Little Cap covering Car Antenna Connector missing,suggestions? - 8525, TyTN, MDA Vario II, JasJam General

Don't know how it happened, but just looked at the back of my Tytn, and it is missing that little plastic/rubber cap that goes over the Car Angenna Connector (that's what they call it in the manual). Can anyone suggest how I could get/buy a new/used one ? I haven't seen any posts of this type of thing happening to anyone else..not sure why? I now realize that it must be a removeable cap. I am surprised that nobody else, seems to lose theirs. Anyways, any suggestions are appreciated. It certainly shouldn't cost a fortune for such a puny thing!..

see if you can find it here..
good luck.

If all else fails, try the end cap from a Bic Stic ballpoint pen -- the little plastic bit plugging the non-writing end of the pen's barrel. Should be pretty close to the right size.

Thank you for your suggestions
Will try your link,, and try your Bic suggestions.

One thing you could also do is use a piece of black electrical tape to cover the antenna hole underneath the battery door. When you put the battery door back on, it will look just as it did before as the tape will be underneath it.

I think I found an almost perfect substitute
I went to the Home Depot and bought a package of Self-Adhesive Foam and Vinyl Pads. Different sizes, but the one that I bought had black ones, different sizes. I just had to trim ,make a smaller circle out of any of the black ones, to slightly ,but barely overcover the hole, then I placed back the back cover on top of it. You should make sure that the pad isn't too thick. Mine were fine. I suppose, instead of even taking off the back, you could approach it by keeping the back on, cutting a round piece that would fit snuggly into the hole. Too boot, the sticky part, should more or less adhere to the exposed bits that are in the hole. I prefered the other way, because it adhered to the actual back of the phone,near the hole a lot better. Hopefully I helped those people find a better way, than using bic pens blunt end. I tried that , but not nearly as good as my method.

Related

Body Glove Case Issues

Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.
chibahawk said:
Anyone else buy and have problems with it? I searched around after thinking I saw a complaint on it like I've got but couldn't find.
Basicly, I put it on started noticing the top was putting pressure onto the screen I think. THe touch screen got extremely laggy, unresponsivess, and just seemed to go crazy. I'm going to try sanding it down on the inside but I think that just sucks.
On top of that the phone fell out of the back/belt clip half one night and caused a nice freakin dent in my phone and allowed the battery to flip out almost down a sewer.
Anyone care to give me a positive review so I don't just throw this thing out?
Also - is it possible to buy a new physical case to replace a scratched/dented case? Not the body glove I mean the actual phone casing.
Click to expand...
Click to collapse
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.
Praygo said:
I have this case and had the same problem. I have read that many others have had it too. Honestly I dont know why a company would put out a product like this. They all should be recalled, however me being me decided to just fix it by Taking a dremel tool and shaving some of the inside part of the screen protector off, making it put less pressure on the screen. It fixed it immediately. The case does a great job in protecting the phone, just a major flaw that can be fixed if you have the time and tools. If you dont, ***** to the company and get your money back and try something else.
Click to expand...
Click to collapse
Yes I could see that the inside casing was a bit rough so sanding should stop the problem - but seriously that's a major issue.
Have you found that it holds the phone well though? Because I'm very upset that my phone fell out of it once already but maybe it was an error on my part and it wasn't secure enough...
I've never had the phone fall out of the body glove case.
i mangled my body glove case.
someone bumped into me and the phone fell out of the case AGAIN.
i ripped it to shreds and left it on the side of the road to rot into plastic hell.
i dont recommend this product.
I returned mine. I had the exact same issues (screen and phone falling out). It also didn't attach properly on the top left corner, it was always bowed out. I don't recommend it either.
Anyone got any else to share?
I was THIS CLOSE ( || ) to buying it. lol
Is there anything out there that's similar to it in design, but better?
returned
When all the way snapped on, mine pushed the top left corner so hard the entire screen would not respond to touch. Returned it.
My friend and i had the same issue. We just took it off messed around with it and put it back and it works fine, SOMETIMES it happens again but we just take it off and put it on.
Since there is not any other case that provides this type of protection we are keeping it. I rather my phone be safe than anything else.
I just ordered mine yesterday so I'm anxiously awaiting its arrival.
What exactly did you have to mod to get it to work? According to my readings, you just need to sand down the edges that connect with the screen right?
I may just buy the case and sand down what was mentioned. I like the design of the case..only one so far I really like.
I've been using one for about two weeks and am very happy with it. Had read about the screen pressure issue on other posts (searching helps folks), and scraped down the top corners before I put it on. Don't need a dremel tool or sandpaper. No problems, fits perfectly. The only warning is that it's a little dicey to take off once it's on -- it really fits snugly.
Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.
Torkrench said:
Yout're talking about the "sand texture" clip-on case, right? If so, yes, I bought the case too. The top cover was too tight and caused the screen issue people are mentioning. That was an easy fix by shaving down the edges that were pressing too hard (actually, I just cleaned off the coating from the plastic that was causing it... The bottom of the case however wouldn't fit at all. no matter what I tried, I couldn't get all of the clips to lock over the edges of the phone. I removed the felt lining and still had issues. I got around it by using thin double sided tape (for a temporary fix until I got a new case). I wouldn't trust the belt clip with the double stick tape though. I ordered the rubberized case on ebay and the fit is perfect. Just get that one. I sent an e-mail in to Body Glove and have had no response yet. We should all get our money back on these cases, or at least a redesigned bottom case that fits correctly. Right now it was just a complete waste of money. It's a shame, because I really liked the feel of the case.
Click to expand...
Click to collapse
Could you give us the link for the ebay one please!
http://cgi.ebay.com/NEW-RUBBERIZED-...5|66:2|65:12|39:1|240:1318|301:1|293:1|294:50
That is the one I ordered, and the fit is perfect. The only thing I wish it had was the belt clip insert for the case included. I don't know where to find one, but I mostly keep it in my pocket anyway.
you guys want a good case that protects? check out the monaco aluminum case, it comes with a clear lens on it which I haven't removed but you could if you wanted quick access to the touchscreen. I work in the construction field and have yet to have it fall off my clip. I also dropped my tilt (when I used it) from about 8" off a ladder and it was perfectly fine. The aluminum case for the fuze isn't any more bulky than the body glove case either.
bilbobrian said:
check out the monaco aluminum case
Click to expand...
Click to collapse
I've got one of these as well...and while it does protect the phone very well it will also lower your signal strength. I've had these type cases for the Wizard and Tilt and now the Fuze...whenever I'm in an area where the signal was a little iffy to begin with I WILL either drop the call or be unable to answer with the metal case. So, stay away from the aluminum ones if you go into lower coverage areas (and no...the slots they cut in the back to help improve the signal don't actually help.)

stylus issues

I just got my replacement phone and the stylus barely "clicks" into place and dosent have that "mushy" feeling as you slide it in to place, and it take nothing to jar it loose.
is there a quick fix in this situation?
Two quick fixes 1 you can put a small piece of electrical tape around it depending on how much you need you just can add or subtract or for a more permanent solution bend the stylus ever so slightly to make it fit snugly.
One fix that will cost soem money and take a bit long
Buy a thicker stylus of ebay by thicker i dont mean buy a different phone im saying buy those heavy duty ones they dont say but there fit is a little bit tighter than the normal ones. (my current stylus is a littler skinnier one with a thicker top but i can remove the black top and its a ball point pen
I lost mine and read to avoid the cheapies, so I searched for true OEM replacements. I bought these on eBay and they work very well. There are many offered as generics or clones, only a few have the real ones. oem stylus
there's a piece of plastic that holds it in there. it sits next to the battery.
GeLopez said:
there's a piece of plastic that holds it in there. it sits next to the battery.
Click to expand...
Click to collapse
Thanks, that was driving me nuts too. I just pushed on that piece a bit and now the stylus is back to being nice and secure!

Third-party add-on request: Battery cover with handstrap clip

It is bothering me that I can't attach a strap to my HD2 which would help getting it out of pockets with cold hands, golves etc. and stop it being dropped. However HTC in their wisdom, or lack of, have not included a hand-strap hole.
So it occurred to me, if some kind souls would make an after-market battery cover with a small hole for a strap on the side (not back it'd be ugly), that would be perfect!
Hopefully will see one on ebay in the coming months!
Sounds dangerous to me, I can see problems with supporting the entire weight of the device by the battery cover while it's pulled out of pockets.
This way of preventing it being dropped would probably result in it being dropped more.
I agree that doing it on the side would be a bad idea, since pulling the sides of the battery cover is how it unlatches.
However, by reasoning along the same lines, it ought to work if done on the back of the phone, where by pulling you would cause the back cover to come together, thus tightening its grip on the sides of the phone.
In fact, I suppose that if you have a Dremel-like tool, you could get a thin drill bit and just drill two small holes in the cover and do it yourself.
The cover is really tight and I don't think it would come off easily with the strap attached.
Drilling is unfortunately not an option, as even if you drill holes, there'd be no space for a thread to go through, so it needs something that stands out a little too.

2 minute lanyard tape hack - drop protection

Something I always liked about my Kaiser was having a lanyard attached to it. I did this after dropping it a couple of times due to it slipping out of my hand.
As the HD2 is even more slippery in my fingers and probably more likely to shatter or break on dropping, I was disappointed that there was no lanyard hole.
I contemplated drilling a hole in battery cover but didn't have a drill. So I've duct taped a lanyard onto the back, a la the attached pic.
First I lay the lanyard ring on the back and threaded duct tape through it, locking the lanyard ring to the phone. Then I layered a bit more duct tape on top to give it some strength.
It may look a bit messy and I could have done it neater. At the end of the day it will (hopefully) stop me dropping and breaking a £500 phone which I'm happy about. It's also surprisingly strong and will give an indication before it eventually gives way. Takes about 2 minutes.
Edit: Ugly duct tape method replaced by neater black tape version.
Edit2: Video howto added: http://www.youtube.com/watch?v=yL3owsWT3E4
Disclaimer: If you try this and end up dropping your HD2 anyway, I accept no responsibility!
That could be the worst monstrosity to a HD2 Ive ever seen.
Haha, you may be right. But I don't have a mobile phone to look pretty, I have it to use it and rely on it to be working when I need it, not broken into 100 pieces on the floor.
Here's a neater black tape version. Not sure it will be as strong as the first though.
Biffy said:
Here's a neater black tape version. Not sure it will be as strong as the first though.
Click to expand...
Click to collapse
looks sooo fragile , also u should try take it to a gravire-er if u dont have a drill and make a hole suitable
Job done no messing!
I can't understand why HC didnt add a lanyard bar and at the end of the day your solution will work and probably save your phone one day.
Nice graduated background on your photo and good image quality, what camera did you use?
It's the Panasonic FT1. A little waterproof compact.
Combining duct tape as the first layer and then black tape over for neatness is the best solution so far.
I've also considered super gluing the lanyard into the 3.5mm jack, but know I'd regret doing it straight after!
well, you guys aint the first to do this.
i invented a similar design a few weeks ago, mine used a 1" belt, meaning it can be strapped to your waist any time you like, safe as houses and pretty cool aesthetically
Final version
After a bit of testing, this is the final method I will use.
Some folded black tape under the battery cover. The battery cover adds extra strength to the tape and it looks so much neater than the Duct tape.
to be honest, that is just ugly. sorry.
I also missed such a whole for it, as I also did that with my Kaiser.
Now I sticked to a Silicon/Plastic Combi Case
why dont you get a jelly case or something like that and you can make hole in it. tape will hold fora few days only
I'm going to get a case as well I think. But the tape solution outlined which is partly under the battery case will last a lot longer than a few days.
The tape should only be under any pressure if you're about to drop your HD2, which won't be that often and then the weight isn't that great.
I think it's a great idea, and the 'under battery cover' mod (V 1.3? ) looks fine. I'm going to try copying it so I can clip it to my handbag, but with fishing line for the loop.
Mariad said:
I think it's a great idea, and the 'under battery cover' mod (V 1.3? ) looks fine. I'm going to try copying it so I can clip it to my handbag, but with fishing line for the loop.
Click to expand...
Click to collapse
Yeah, I agree. The third version looks nice and clean! The only question is: What did you attach the tape to? To the cover itself? Because I wonder how much strength it requires to pull off the cover and if that wouldn't happen if the device falls...
EDIT: I love how you labeled this a "hack"!
I attached the tape to the plastic under the cover, where the sim card is. I'll put a quick video together to illustrate.
I left it hanging by the lanyard last night, for about 7 hours, 7 feet in the air, no probs. It's not intended to be pulled as hard as a regular lanyard loop may be, but for a precaution if the phone slips from your hands. And then it will be fine.
And here's the not very good howto video: http://www.youtube.com/watch?v=yL3owsWT3E4
I dont mean to jinx you or anything, but the piece of string from the lanyard could easily split the single layer of duct tape where it's folded.. that's going to be where the weak point is....especially considering the weight of the HD2. It's not going to matter how many pieces of tape you've got under the batter cover.
Now if you were to have your HD2 on a desk or in your pocket, the temptation of grabbing it by the lanyard will be there... or if someone else decided to yank the lanyard.....
I'd suggest trying that method of attachment on something of a similar weight and shaking it around for a bit to see how the duct tape handles.
Remember... the HD2 screen is thin glass... One drop on a hard surface or if it lands at the wrong angle, it'll be time to order a new one!
I've tested it by pulling far more strongly on the lanyard than it ever would be subjected to in real use. I was able to pull it hard about 20 times before the tape started to give way. By then it was visibly starting to tear away, so you should have a good warning before it breaks. It will perfectly suit my needs anyway and I might try doubling the tape up for more strength next. Also, I think this could be improved by using even stronger tape.
Very good on the last release.
Great idea, man.
I'm going to try, but I've only two left hands....
Pink strap should be nice too ;-)

Iffy Proximity Sensor

Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
bert682 said:
Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
Click to expand...
Click to collapse
Ok so I did a little more reading and it seems that a gorilla has changed the screen on this phone in the past and he / she has used compound to stick the screen down and some of it has gone around the sensor and the resulting press down on the screen has created a few air pockets.
Looking less forward to changing the screen now as no doubt with my luck the "technician" will have used some crazy heat resistant glue!
Also....missing the speaker grille....funny how you only notice things after you have bought them!
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
It will work for sure, I posted this fix on a YouTube screen replacement guide of octopus glues I think and its confirmed to work from a lot of people. Then if you use a custom rom go to brightness settings while having auto brightness enabled and try changing light sources from dark to very bright places to see the instant lux values you get. If you are not satisfied with the result try custom auto brightness values.
Sent from my Nexus 4 using Tapatalk
bert682 said:
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
Click to expand...
Click to collapse
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Planterz said:
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Click to expand...
Click to collapse
I got a "kit" off eBay, [URL="http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT"]http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
That's the full part. The one you've posted is the type I usually go for, they're good quality so far.
bert682 said:
I got a "kit" off eBay, http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
Click to expand...
Click to collapse
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you), I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other components shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Planterz said:
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you, I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other comments shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video[/i] that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Click to expand...
Click to collapse
Awesome, I saw some cheaper screens but that one notes that its LG compliant etc. I bought a set of tools separately so will have all the stuff needed. Didnt think about the battery, will order one as it does make sense!
Thanks for the info, will update as I go.
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
bert682 said:
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
Click to expand...
Click to collapse
Yeah this is normal.
Sent from my Nexus 4 using Tapatalk
bert682 said:
New screen in and working well.
Click to expand...
Click to collapse
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Planterz said:
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Click to expand...
Click to collapse
No, not with the correct tools. I will admit had I not bought the plastic tools, tweezers etc I may have struggled.
The battery was my main concern, its really stuck down, even though this had been replaced before and likely a less tacky glue used it was still tough. Had to use some heat to soften it and the "battery cover" has seen better days. Next thing to replace is that, just for piece of mind.
All in all, pretty nice experience, the phone seems more modular that other phones I have taken apart which is nice.

Categories

Resources