I've had this issue with my wife's vibrant. I hook up to the PC and went I pull down the status bar and there's nothing about usb on it. It just charges. Help plz. I'm a noob in parrell
Sent from my LG-P999 using XDA App
anyone find a solution? my phone will charge when plugged in but only randomly says its debugging (yes i have it checked). Also, when i unplug my phone itll still say its charging for like the next hour
What rom are you on, sounds like recognition issues. MIUI or cm7 may not recognize your pc, ie charging issues, different drivers.
Also it could be your cable, if you have another give it a shot, also if you haven't tried a different usb port, try that.
Sent from my Vibrant running Ice Cream Sandwich
@fatchuckyd: not sure what your problem is, but try this out in your setting.
Go to Setting/Application/Development, then check on the first 2 boxes: USB debugging, and USB debugging notify.
Hope this help.
@WhiteBoyAwesome: use the original USB cable that comes with your phone.
Related
My phone just stopped connecting to my computer over USB. I went to update Fission to 1.2.1 and got stuck at trying to actually connect my phone to the computer. USB debugging is enabled and SetCPU is setting the USB charge profile, but I don't get either of the notifications I'm used to, and my computer doesn't register that I plugged it in. Anyone else run into this?
About phone states that the battery is discharging as well. Bad cable? Charges just fine over the other charger I have (dedicated wall charger, so I can't swap cables).
vcarl said:
My phone just stopped connecting to my computer over USB. I went to update Fission to 1.2.1 and got stuck at trying to actually connect my phone to the computer. USB debugging is enabled and SetCPU is setting the USB charge profile, but I don't get either of the notifications I'm used to, and my computer doesn't register that I plugged it in. Anyone else run into this?
About phone states that the battery is discharging as well. Bad cable? Charges just fine over the other charger I have (dedicated wall charger, so I can't swap cables).
Click to expand...
Click to collapse
Sometimes its something simple. Are you trying to access your SD card? Make sure your USB sync is on USB Storage.
I get this problem as well. If I reboot my phone a few times it seems to start working again.
Yep, sure enough, after a second reboot it works fine. Thanks.
Make sure your USB sync is on USB Storage.
Click to expand...
Click to collapse
That was the problem, it never even gave me that option. just didn't register that it was plugged in at all.
vcarl said:
Yep, sure enough, after a second reboot it works fine. Thanks.
That was the problem, it never even gave me that option. just didn't register that it was plugged in at all.
Click to expand...
Click to collapse
Always try a reboot when something goes wrong. Id say 75% of the time it will fix your problem.
Might or might not be related, but...I just recently got a Droid 2 to "play with" and noticed that the internal memory can't be read by Astro File Manager or the stock "File Manager". When I plug the phone to my Mac I can only mount the SD card. I'm still looking at older threads but I figure I ask here just in case.
When I plug my usb cable in the phone beeps as if its charging but no usb icons come up.
usb debugging on is and its set to usb mass storage.
ive tried turning off the settings and then turning them on with it unplugged
any help would be great
Do you have the drivers installed?
Are you plugging your phone in through a USB hub or is it directly plugged in?
Do you have the usb icon in the notification bar at the top of your screen? If so just drag the bar down and click on it. It will ask you if you want to mount the sd card.
Sent from my SCH-I500 using XDA App
What ROM are you running?
I have the same issue. It seems these phones are EXTREMELY picky about what USB cables that you use. I don't have the stock one anymore (damn cat), I have a few LG's and two from a Droid 1. All of them I have to 'wiggle' a little bit to get my computer to see the phone. Please remember not to push or force the cord, otherwise you will snap the charge port.
- Also, yes I get the USB icon
- Yes it is charging
- Yes I have the right drivers installed
Also sometimes I get "this device can preform faster", it just seems to me that the opening for the cable is a odd size and the other non OEM cables do not fit so well.
Hey guys,
I am running Binox Next Gen V2 and it was running great until a week ago. I am ahving issues where when I plug the phone in the charger it doesnt charge, but when I unplug it says "Battery low. Please Plug in charger to keep using." When the phones on and I connect it to the computer Odin picks it up however, when i actually go into downlad mode and plug in the usb cable nothing happens..My computer beeps twice and odin doesn't pick it up either..
Any suggestions on what's wrong or what could be causing these issues?
Try looking at the pins on the bottom of the USB charging cable to see if any are pushed too far in, cuz I had both pins on my cable pushed in and the phone port wouldn't read it from time to time. If it is, just take a needle and bend them out again.
Sent from my SGH-T959 using xda premium
Just starting yesterday, when I plug my phone into my computer all it does is charge. No option to mount, no "usb not recognized", nothing. I can get into download mode but Odin doesn't recognize it.
I've searched dozens of other threads, tried most suggestions and can't seem to get anything to work. Suggestions would be appreciated.
Maybe you don't have drivers or bad USB I have 2 one only charges the other does both
Sent from my SGH-T959 using XDA App
Reboot the phone
Sent from my SGH-T959 using XDA App
I have the drivers, I've had no problems connecting previously. I've rebooted the phone multiple times.
Out of 3 galaxy s type devices: 1 doesn't even charge anymore, 1 charges but wont do data and 1 works if the cable is held at an angle. I think samsung can't make usb ports
I'm just now about to start a post asking how to change roms with out my usb. I had the same problem start months ago. First things where normal. Then, every now and then I would have to re plug the usb cable into the port to get it to mount. Then finally one time it just all together stopped working. I can charge, the charging icon comes up but no mounting options.
On the bright side, this is the first phone I have ever owned that I can just sync over wifi. And at least its not an apple device, if charging stops I can get an external battery charger ; )
Nick
My vibe is over a year old and I never close the door on the usb port. When I had the same issue as the OP it was a dirty usb port. I carefully cleaned it, which took a few times and it finally worked. Do it with the battery pulled. The loose port is caused from the male end of the original cable not the phone so I bought a new cable and it fits snug.
I have a serious issue with my Nexus 7 2012. I put CM11 on it and all was great. The power got down to 11% on me, so I plugged it into my computer. I noticed it wasn’t charging, MTP didn’t kick in, and I couldn't get into ADB. I figured I’d screwed up the USB port. I tried different cables all with the same results. I turned the tablet off and plugged it in and the battery started charging. I couldn’t get MTP or PTP to work nor could I get into ADB after it was charged. I did a factory reset, clearing everything, and reinstalled. Same issue.
I can use my OTG cable and TWRP to install software on the tablet. I tried AKOP ROM. It allows me to use my OTG cable but the tablet doesn’t charge. I try to toggle MTP to PTP or turn off USB debugging and the tablet locks and reboots. I try to turn off the developer options toggle and the tablet locks and restarts.
Help! I don’t know what to do with it. I've searched all day.
Check the basics. When you plug your N7 into your computer, are you using a USB 2.0 port? Is it directly mounted on the computer's motherboard (i.e., a rear port)? Are the proper drivers installed so your N7 is recognized as a Nexus 7?
USB specifications only provide .5A power, v. 2.0A power from the AC charger. Get your N7 fully charged,then get back with whether it locks and reboots.
exglynco said:
Check the basics. When you plug your N7 into your computer, are you using a USB 2.0 port? Is it directly mounted on the computer's motherboard (i.e., a rear port)? Are the proper drivers installed so your N7 is recognized as a Nexus 7?
USB specifications only provide .5A power, v. 2.0A power from the AC charger. Get your N7 fully charged,then get back with whether it locks and reboots.
Click to expand...
Click to collapse
Thanks for the reply. Yes. I've done all of that. Multiple computers, multiple cables, multiple chargers. The Nexus is at 100%.
Here's the exact issue I have now: http://forum.xda-developers.com/showthread.php?t=2536272
Well. I'm going to say disregard. My searches show that a craptastic 12 volt car charger probably hosed the N7's mother board. I'm going to try one more fix but I'm sure it's toast.