Related
Hi All.
I just received the faulty part in my Trinity from cnn.cn. it's the keypad panel which doesn't work that well on my device anymore.
http://cnn.cn/shop/p3600dopod-d810-keypad-p-1825.html
Now, I read the excellent tutorial on how to disassemble the Trinity, but I'm worried about the Warranty sticker found on one of the screw hole.
the question is - is there a way to replace this part without unscrewing that specific screw?? Is there any way to avoid voiding my warranty??
thanks in advance
KamaL said:
Hi All.
I just received the faulty part in my Trinity from cnn.cn. it's the keypad panel which doesn't work that well on my device anymore.
http://cnn.cn/shop/p3600dopod-d810-keypad-p-1825.html
Now, I read the excellent tutorial on how to disassemble the Trinity, but I'm worried about the Warranty sticker found on one of the screw hole.
the question is - is there a way to replace this part without unscrewing that specific screw?? Is there any way to avoid voiding my warranty??
thanks in advance
Click to expand...
Click to collapse
Hello!
I had the same problem with my device. From my point of view dissabamling the phone without breaking the sticker is not possible.
KamaL said:
Hi All.
I just received the faulty part in my Trinity from cnn.cn. it's the keypad panel which doesn't work that well on my device anymore.
http://cnn.cn/shop/p3600dopod-d810-keypad-p-1825.html
Now, I read the excellent tutorial on how to disassemble the Trinity, but I'm worried about the Warranty sticker found on one of the screw hole.
the question is - is there a way to replace this part without unscrewing that specific screw?? Is there any way to avoid voiding my warranty??
thanks in advance
Click to expand...
Click to collapse
jus slip a very thin blade or knife between the sticker and plastic, keep pushin the sharper egde of the blade between them as centred as possible. without movin the blade up or down. and it wil come off. i easily removed my void label. and put it back. muahahaha.
can you point me to the guide for disassmbly please? I took mine apart but couldn't get the last screen connector cable off.
I'm a bit of an expert at removing tamper resistant stickers, but this one would not play ball.
Usually the trick is to warm them or shear them rather than pull, but this pretty much disintegrated when I looked at it ;-)
Just one point - if it's under warranty why are you fixing a faulty part?
ayyu3m said:
jus slip a very thin blade or knife between the sticker and plastic, keep pushin the sharper egde of the blade between them as centred as possible. without movin the blade up or down. and it wil come off. i easily removed my void label. and put it back. muahahaha.
Click to expand...
Click to collapse
Great, I hope I'll manage to do the same. I actually had the same idea, but was afraid the sticker is too "sticky"
can you point me to the guide for disassmbly please? I took mine apart but couldn't get the last screen connector cable off.
I'm a bit of an expert at removing tamper resistant stickers, but this one would not play ball.
Usually the trick is to warm them or shear them rather than pull, but this pretty much disintegrated when I looked at it ;-)
Just one point - if it's under warranty why are you fixing a faulty part?
Click to expand...
Click to collapse
Here's the tutorial:
http://forum.xda-developers.com/showthread.php?t=311463
Regarding your question - sending my device which was bought abroad would cost me much more than the piece+shipping (15$), not to mention the entire weeks I'll be without my device. So I think it's worth the "risk"
nope man! the sticker is not sticky at all....even the stickies on this forum are much stickier than the void label
thanks for putting the link up for Dimantos guide! I've been trying to find it for ages.
The part I get stuck at it removing the screen connector (Red arrow).
I just can't work out what to lift up - it seems like something might break.....
sickboy555 said:
thanks for putting the link up for Dimantos guide! I've been trying to find it for ages.
The part I get stuck at it removing the screen connector (Red arrow).
I just can't work out what to lift up - it seems like something might break.....
Click to expand...
Click to collapse
Hi my friend.
What you have to lift up (using tool No2) is the black lever so that the cable ribbon can slip out of the plug. What you have to be careful with is not to accidentally cut the cable ribbon.
I hope its clear now.
Best regards!
Nice Tutorial
First of all i'd like to thank for this great tutorial. Just followed it and managed to disassemble trinity without breaking anything.
Just wondering if you guys know where to buy the nuts where the screws fasten on the front cover (those little golden pieces, inside the plastic). Bought a black cover from ebay that doesn't have that, so i cannot fasten the screws to reassemble
Thanks in advance
I dropped my phone and need to replace the housing. It looks like the digitiser cannot be easily removed from the housing, so I bought one of these as well. Now all I have to do is move the phone from the old housing to the new and install the digitiser in the new housing.
Now it looks like the digitiser may have been glued in place. What type of glue should I use ?
::Pixel.Freak:: said:
I dropped my phone and need to replace the housing. It looks like the digitiser cannot be easily removed from the housing, so I bought one of these as well. Now all I have to do is move the phone from the old housing to the new and install the digitiser in the new housing.
Now it looks like the digitiser may have been glued in place. What type of glue should I use ?
Click to expand...
Click to collapse
More liked taped in...... I'm sure that lots of people will respond with.. Double sided 3M tape.... but if there's anything better/stronger than that on the market use it. Make sure it''s really thin tape to. I'm gonna be replacing my housing in the next month or so aswell. Goodluck.
As I also will replace mine digitizer, the newton rings are bugging me, it will be appreciable if you can share your experiences of the replacement process.
thanks in advance and god luck
Hey on more thing. I took apart my phone last night and put it back just so I know my way around when parts come in.
If your Digitizer does not work try loosening the top srews 1/4 turn. You have them on too tight.
I wasn't replacing mine so I didn't have to remove the existing one. All I had to do was attach a new digitiser to a new housing.
I was told that double sided tape was the best, so I tried that.
I used the instruction from http://www.pdacenter.ru/razborka/htc-touch-diamond2 which was easy enough.
You need to ensure you remove the micro SD card first.
Also I forgot to move the LED diffuser from the top, so I need to repeat the process at some stage.
The housing I bought had a number of issues
* The two screw point near the bottom of the housing didn't have the metal inserts with the screw threads
* There was no seal between the metal housing and the LCD screen. This could let dust in.
That's about it for a brain dump.
Hi there,
I was also tired from that oil stai and ordered a new digitizer from these guys:
http://xxx.sw-box.com/htc-touch-diamond-2-t5353-digitizer-touch-panel-screen.html
Surely it arrived in 6 days, to my horror it was a generic display,
Had some trouble removing the old one, ended up breaking it
The generic did not fit snugly, I had to sand down the edges to make them round, also had some trouble with the four buttons below getting stuck when pressing down, (shaved of some extra plastic). anyway used double sided scotch film to get the digitizer back in place.
apart from a few difficulties, it works like a charm.
Should have ordered an OEM but what's done is done
Next time I'll do the cover and get a new digitizer
Regards
I would of thought double sided tape too thick to use to stick the digitizer on.
I was thinking of using a very thin sliver of clear silicone.
Anybody tried this or have any other suggestions?
Thanks
I used a very thin layer of supergleu and it worked great!!
My digitizer came pre-glued. I didn't need any sort of glue.
http://forum.xda-developers.com/showthread.php?t=715724
Silicone is OK
I used a very thin layer of black silicone and placed a book on top of the digitizer to keep it pressed flat into the case as it dried overnight. No problems since then...
The missing metal screw inserts can simply be pulled out of the old housing ; insert screw halfway and gently pull with plyers. Carefully hammer into the new casing; insert screw 3/4, put something thin and metal on top to prevent the screwhead from getting damaged and carefully hammer into the void. Make sure it goes in straight.
I've got exactly the same issue with my new housing, no bottom screw threads and no foam for the lcd to rest on. Am trying to pull the threads out with pliers but I think the old case is going to break first or strip the threads.
This is isn't an easy job
have finally finished this epic!!!!
had to break the bottom screw threads out of the old front housing and took a good while hammering them into the new housing so I didn't break it.
used a small sliver of clear silicone to glue the digitizer in which seems to work well so far.
Have not put any foam or anything for the LCD to rest on, time will tell what effect this has.
I need to change mine as well. Where can i buy a good quality digitizer and case preferably pre-glued?
I found a few on ebay but i am not sure of the quality.
Thanks
Today i searched also for shops which have digitizers and housings. I have found 2 shops, but one of them is a german shop (http://www.mobileok.de) which does not deliver outside of germany and austria. But the other one does: http://www.sw-box.com/
what kind of glue? it's the third time that i'm re-gluing it, but dust keeps coming inside....
I guess, it is not possible to hermetical seal the housing. I had dust in my original housing too. There are a lot of small gaps everywhere not only between digitizer and frame. But it would be easy to disassemble the device from time to time, remove the dust and reassemble it again. Save your energy in the effort to make your device dust proof.
I posted in another thread about the issue of digitizer being glued to lcd. I had more pics to show, and decided disassembled pics are useful to all! So new thread for full set! If you want more I can get more! If I get enough questions I might make a tutorial for dis assembly.
General Disassembly
Slideshow:
http://img96.imageshack.us/slideshow/webplayer.php?id=htchd2wificam2.jpg
Desoldered Digitizer Pics
Slideshow:
http://img705.imageshack.us/slideshow/webplayer.php?id=htchd2desolderedtermina.jpg
Digitizer Removal w/ Razor
Slideshow:
http://img696.imageshack.us/slideshow/webplayer.php?id=htchd2digioffrazor.jpg
ENJOY!
This really is a great phone!
can't see anything. please use a different host
brandi said:
can't see anything. please use a different host
Click to expand...
Click to collapse
Fixed problem!
OH NO!! what HAVE U done!!!
I know...The horror...I haven't re-assembled to see if still working...HA!
I disassembled because of a cracked digitizer.
looks like a fur or "plastic" carpet, hope you don't end up with ESD related problems
ESD as in ElectroStatic Discharge ^^
Phone still works just fine.
If anybody knows how to un-solder the digitizer away from the lcd, help would be appreciated!
New images added.
Next up:
digitizer/lcd separation
any updates?
Have you managed to fix it yet?
We all want you to succeed so we can operate on our own cracked ones! Maybe you need the "unglue" chemical - you know, like superglue has an antiglue for reversing it's stickiness. If you could find out what glue bonded it, then a specialist adhesive supplier probably knows how to reverse it.
I'm sure you'll like this (if it isn't posted here before...)
http://pocketnow.com/hardware-1/official-htc-hd2-disassembly-assembly-training-videos-leaked
Still not clear, has he finally removed the lcd on that video from the digitizer? to me it looks they're still cemented
tamas970 said:
Still not clear, has he finally removed the lcd from the digitizer? to me it looks they're still cemented
Click to expand...
Click to collapse
Well if they're cemented (hopefully with some hyper-glue), thats a GOOD thing. Then this will be (hopefully) my first device with NO dust under the glass.
Don't you people have insurances on your devices? Talk to the ensurance company and you will get a new device for a small excess - that is, if it's beyond repair
Halle said:
Well if they're cemented (hopefully with some hyper-glue), thats a GOOD thing. Then this will be (hopefully) my first device with NO dust under the glass.
Click to expand...
Click to collapse
its not ... I have dust under the displayglass.
Floatheavy, and everyone else.
I'm currently on my second HD2, first suffered a hairline crack on the digitizer and it went COMPLETELY unresponsive. After getting the second, I had nothing to loose and disassembled the first. I got everthing apart up to the LCM, this module has everything (the glass digitizer, the LCD and the backlight) all cemented together. As I took the phone apart, priodically I would test that it still worked - everything except the digitizer. When I tried to separate the digitizer from the LCD and baclight I ended up tearing the layers of the LCD apart, now one layer is still glued to the digitizer and one is still glued to the backlight. I have yet to see how this can safely come apart and untill I can buy the LCD the phone is totaly screwed. I think one has to purchase an entire LCM and not just the digitizer.
For those that want to try separating the digitizer - BEWARE, noone seems to have found the secret yet! If I manage to discover something new I'll post.
Yeah. I tried the heat method to separate the digi from the LCD...
No luck
It seems it is more than the simple adhesive broken down by heat.
To get the bezel away from the LCM you can use heat to make easier, but to get the digitizer away from the LCD itself remains a mystery to me.
Anybody get any other results?
OKAY..
Pics updated again...
I was able to get the digitizer apart from the LCD, using a razor.
for separate lcd and digitizer
For separate lcd and digitizer, I used nylo fisher string... and it work good... just right my problem is how to past new one ? neopren glue ?
Honestly, I plan on just adding a dot of super glue to each corner.
I believe most phone adhesives are a sylicon based glue.
It`s almost impossible to un-solder the digitizer away from the lcd, i have succeeded a few times whit hot air and very sharp cutter, but still broke 2 screens from 5...it has to be a solution for this...anyway 3 phones from 5 its not the best rate...
Does anyone know a site where to buy that? I have the white version but black is fine also. I would like a full replacement, digitizer included.
Will it avoid my warranty if I replace it? And do I have to open the whole thing to replace the digitizer only?
thanks in advance
I can't find housings anywhere. And beware, I replaced the digitizer, and when I put it back together, the lcd was cracked in the corner; it's glued on with damn gorilla glue I swear, you will not be able to replace the digitizer without hurting the lcd unless you can somehow get the glue to unbond. Also, yes, you have to take the phone completely apart (like, the last step of disassembly in the service manual) to get at the digitizer.
You can find service manuals in pdf on google
Good luck if you attempt anything, but I wouldn't reccommend it!
*EDIT - Yes you will well and truly void the warranty
try this
http://mobile.brando.com/samsung-gt...eplacement-housing-white_p05872c0670d088.html
Hey everyone my HTC HD2 got the Non-Responsive screen problem a week ago, & did a lot of research and found out that it was most likely a hardware problem with a cable..... So a lot of people would tell the people with the problem that the "Touch Screen Digitizer" is dead (like the cable), or it needs to be cleaned... pretty well go out and buy a new one... BUT I have never found evidence that someone has done this and it has successfully "cured" their HTC HD2 Non-Responsive touch screen problem...
So I was looking for anyone on the forums that could confirm this is a solution or give me any tips on what I should do.... AND no I don't have enough money to get a new phone, nor do I live in the USA so I can't send it in to fix it...
This is what I was going to buy for it:
http://www.ebay.ca/itm/NEW-OEM-HTC-...781?pt=LH_DefaultDomain_0&hash=item519a3d2e45
Thanks for taking the time to read my Thread, its much appreciated!! I hope I can find a fix!!
PS: If anyone wanted to know what it looks like out of curiosity I posted 3 pictures with RED circle HIGHLIGHTING the problem when I try to touch something....
My digitizer has been a bit dodgy for the past few months. It's ironic that when I finally found out what the issue was and called HTC, my factory warranty had ended exactly 4 days prior to the call.
Fast forward 3 months and my phone has now been unresponsive for 3 hours despite my prying and tweaking various hard parts.
I disassembled the phone down to the main board just to see how hard the install is, but it's a bit intimidating once it's time to start pulling all the film and ribbons. A bit too tight and small parts for my liking.
Time to hit CL to see if I can find a cheap replacement.
Good luck with your repairs. I may be following in your footsteps if I can not find a good deal.
Yeah I will see how well it goes... if anyone has useful info, i will be more than grad to hear it
Thanks
Many people attempt to replace a digitizer, but I simply don't recommend it, we see enough of do-it-yourselvers who created problems in addition to the original ones.
What I do recommend, however, and I stated it on many threads already, is to get an LCD+DIGITIZER assembly. Simply because it is easier to fit. Not saying the overall fitting is easy, always depends on your overall skill, so ensure that you are familiar with the procedure BEFORE you begin. But you will save yourself a lot of trouble by getting the whole thing, as opposed to the digitizer only for the sake of a few bucks.
However, if anyone still feels intimidated by the whole thing, I am on the lookout for working main board. Advertised a few times in the marketplace with limited success. So if anyone smashed their baby and will be looking to replace, rather than repair - drop me a PM. I am in NZ. Will pay by Paypal.
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
cheeselump said:
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
Click to expand...
Click to collapse
How much did the set cost?
cheeselump said:
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
Click to expand...
Click to collapse
Thanks I will check it out, hopefully it won't be to hard and I hope I can repair it!! oh and could you post a link of the youtube & manual you used to replace your screen?? Thanks
Oh would anyone suggest then just calling HTC and sending it to them to repair?? or does that cost to much??
Thanks everyone for the help
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
GnatGoSplat said:
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
Click to expand...
Click to collapse
Yah I was looking at the video's and they were taking off EVERYTHING... it looks really hard to do.. I don't know whether I want to do it anymore.....
oh and are you talking about the digitizer itself or the LCD+digitizer for your method?
Thanks
Heronization said:
Yah I was looking at the video's and they were taking off EVERYTHING... it looks really hard to do.. I don't know whether I want to do it anymore.....
oh and are you talking about the digitizer itself or the LCD+digitizer for your method?
Thanks
Click to expand...
Click to collapse
Yep, there is absolutely no reason to take off everything like some people seem to think is necessary.
The way I'm talking about requires removing LCD+digitizer. In fact, I think you'll always have to remove both because the connector for the digitizer is under the LCD. Anyway, the way I did it, I went from removing the the phone insides from the rear housing straight to separating the LCD+digitizer assembly from the frame. No removal of any boards or flex cables. The only cable to be disconnected is the LCD+digitizer assembly one. Getting it disconnected and reconnected does require unplugging the front button flex and removing the screws for the bottom logic board to loosen it, but that's all.
GnatGoSplat said:
Yep, there is absolutely no reason to take off everything like some people seem to think is necessary.
The way I'm talking about requires removing LCD+digitizer. In fact, I think you'll always have to remove both because the connector for the digitizer is under the LCD. Anyway, the way I did it, I went from removing the the phone insides from the rear housing straight to separating the LCD+digitizer assembly from the frame. No removal of any boards or flex cables. The only cable to be disconnected is the LCD+digitizer assembly one. Getting it disconnected and reconnected does require unplugging the front button flex and removing the screws for the bottom logic board to loosen it, but that's all.
Click to expand...
Click to collapse
Wow that sounds pretty simple! and for you it all works perfectly now?? no calibration needed or problems?? Maybe I will try it after all..... but what screw drivers to I need to dissemble it?? the screws look different from normal..
Heronization said:
Wow that sounds pretty simple! and for you it all works perfectly now?? no calibration needed or problems?? Maybe I will try it after all..... but what screw drivers to I need to dissemble it?? the screws look different from normal..
Click to expand...
Click to collapse
Well, it's not that simple because simply getting the HD2 insides out of the rear housing is difficult if you've never done it before. I believe the screwdriver you need is a Torx T-5. Once you get the screws out, you will need a plastic opening tool to go between the digitizer and rear housing frame. They look like this:
http://www.ifixit.com/Tools/Plastic-Opening-Tools/IF145-000
I found it comes out much easier if I use the tool to make a gap along the top edge and then slide the entire end of a scrap credit card into that gap, then that makes the whole assembly easier to pry out along the sides with the tool. I know on one of the vids, the guy takes forever doing this part and I can understand why, but once I figured out sliding a credit card into the top gap as far as it would go, I was able to get it apart much easier.
I can't answer whether the phone will work properly, because I just ordered the new digitizer over the weekend and haven't put it back together. I did remove the LCD+digitizer assembly and then re-connected it and put it back, then powered on the phone just to make sure pulling the LCD didn't hurt it - it didn't, everything worked as well as it did before. I did manage to crack the digitizer more when I tried to get the insides out of the rear housing before I figured out the credit card trick, so fortunately I was not trying to save my digitizer as it was already cracked. If you are just wanting to try to clean or fiddle with the connection, then you're going to have to be a LOT more careful than I was because it was all too easy to crack the digitizer!
I'm guessing yours probably needs replacement though. I sent my HTC Surround in for a funny acting digitizer, and the digitizer was replaced.
Oh, and if I would have bought an LCD+digitizer pre-assembled unit, that would have been super easy to replace. However, I opted to save $50+ by buying just the digitizer. Not too sure how I'm going to prevent dust getting in it, and I've read thickness of the adhesive is critical. I may regret it later!
GnatGoSplat said:
Well, it's not that simple because simply getting the HD2 insides out of the rear housing is difficult if you've never done it before. I believe the screwdriver you need is a Torx T-5. Once you get the screws out, you will need a plastic opening tool to go between the digitizer and rear housing frame. They look like this:
http://www.ifixit.com/Tools/Plastic-Opening-Tools/IF145-000
I found it comes out much easier if I use the tool to make a gap along the top edge and then slide the entire end of a scrap credit card into that gap, then that makes the whole assembly easier to pry out along the sides with the tool. I know on one of the vids, the guy takes forever doing this part and I can understand why, but once I figured out sliding a credit card into the top gap as far as it would go, I was able to get it apart much easier.
I can't answer whether the phone will work properly, because I just ordered the new digitizer over the weekend and haven't put it back together. I did remove the LCD+digitizer assembly and then re-connected it and put it back, then powered on the phone just to make sure pulling the LCD didn't hurt it - it didn't, everything worked as well as it did before. I did manage to crack the digitizer more when I tried to get the insides out of the rear housing before I figured out the credit card trick, so fortunately I was not trying to save my digitizer as it was already cracked. If you are just wanting to try to clean or fiddle with the connection, then you're going to have to be a LOT more careful than I was because it was all too easy to crack the digitizer!
I'm guessing yours probably needs replacement though. I sent my HTC Surround in for a funny acting digitizer, and the digitizer was replaced.
Oh, and if I would have bought an LCD+digitizer pre-assembled unit, that would have been super easy to replace. However, I opted to save $50+ by buying just the digitizer. Not too sure how I'm going to prevent dust getting in it, and I've read thickness of the adhesive is critical. I may regret it later!
Click to expand...
Click to collapse
Ok thanks I think thats what I am going to do, first dissemble it then try to move the cable around because, just yesterday it started to work again and then today it isn't working. I will contact you if I have a problem or get stuck, if that is ok with you
Thanks a lot
Heronization said:
Ok thanks I think thats what I am going to do, first dissemble it then try to move the cable around because, just yesterday it started to work again and then today it isn't working. I will contact you if I have a problem or get stuck, if that is ok with you
Thanks a lot
Click to expand...
Click to collapse
Yeah, no prob. I can post a pic of the digitizer lifted from the frame which shows where the adhesive tapes are that you have to go through, if it would help.
GnatGoSplat said:
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
Click to expand...
Click to collapse
Hey lolz I need your help already, I just took off the back housing and now Im lost on what to do... It looks to me as if you do have to remove the cables from the motherboard to get to it?? and what is the double sided tape? and isn't everything connected to the lcd?? lolz this is my first time doing any phone disassemble.. Thanks
added a picture of what I was thinking of doing... or am I doing this all wrong... because you did say we don't need to remove any flex cable or wires and stuff
Thanks!!
Heronization said:
Hey lolz I need your help already, I just took off the back housing and now Im lost on what to do... It looks to me as if you do have to remove the cables from the motherboard to get to it?? and what is the double sided tape? and isn't everything connected to the lcd?? lolz this is my first time doing any phone disassemble.. Thanks
added a picture of what I was thinking of doing... or am I doing this all wrong... because you did say we don't need to remove any flex cable or wires and stuff
Thanks!!
Click to expand...
Click to collapse
Nope, I didn't disconnect anything except the circled connector on the far right of your picture. You will need to do that to remove the LCD flex cable from the logic board.
I've attached a pic of the LCD module loosened from the frame. What you do is use something thin and flat to separate the adhesive tape holding the LCD to the frame. You will need to lift some of that black fabric tape on the edge to see where the LCD module meets the frame. Near the top, you will probably have to slide your separating tool all the way through to separate the tape (I used a scrap credit card). Avoid the area where the LCD flex cable is, because you could damage it! It's on the lower right of the LCD if you are looking from the front. When the LCD is loose, lift up from left to right (when LCD is facing you), pretending that there is a hinge on the right side. This is because you don't want to put any force on the LCD flex.
Once you've got your phone looking like my picture, you can remove the "captain" (orange tape), unlatch the LCD flex from the top, remove the button flex from its connector, then loosen the bottom logic board from the frame just enough to pull the flex out of the connector.
I hope that makes sense! It probably helps to know that a very strong double-sided sticky tape is all that holds the LCD+digitizer assembly to the frame, and there is only one flex cable connecting LCD+digitizer assembly to the rest of the phone.
GnatGoSplat said:
Nope, I didn't disconnect anything except the circled connector on the far right of your picture. You will need to do that to remove the LCD flex cable from the logic board.
I've attached a pic of the LCD module loosened from the frame. What you do is use something thin and flat to separate the adhesive tape holding the LCD to the frame. You will need to lift some of that black fabric tape on the edge to see where the LCD module meets the frame. Near the top, you will probably have to slide your separating tool all the way through to separate the tape (I used a scrap credit card). Avoid the area where the LCD flex cable is, because you could damage it! It's on the lower right of the LCD if you are looking from the front. When the LCD is loose, lift up from left to right (when LCD is facing you), pretending that there is a hinge on the right side. This is because you don't want to put any force on the LCD flex.
Once you've got your phone looking like my picture, you can remove the "captain" (orange tape), unlatch the LCD flex from the top, remove the button flex from its connector, then loosen the bottom logic board from the frame just enough to pull the flex out of the connector.
I hope that makes sense! It probably helps to know that a very strong double-sided sticky tape is all that holds the LCD+digitizer assembly to the frame, and there is only one flex cable connecting LCD+digitizer assembly to the rest of the phone.
Click to expand...
Click to collapse
Awesome I will try it now, I do need to heat the screen some for the tape to get sticky so I can pry it off right?? and I am guessing once you have removed that tape you can't "just stick it back on together and it will work right?? right??
Heronization said:
Awesome I will try it now, I do need to heat the screen some for the tape to get sticky so I can pry it off right?? and I am guessing once you have removed that tape you can't "just stick it back on together and it will work right?? right??
Click to expand...
Click to collapse
You could try heating; I didn't, but maybe it will come apart easier if you do. In the HTC factory service video, they mentioned putting the whole phone into the oven to loosen the tape. I didn't know if it would be a good idea to do that complete with all the circuit boards or not.
No, without heat, the tape is definitely ruined and I will need to replace it. I was planning to use some leftover tape I have from fixing iPhone digitizers so I didn't even attempt to salvage the existing tape. Not sure if it's even possible to salvage that tape considering you need to stick some kind of tool in there to separate it.
GnatGoSplat said:
You could try heating; I didn't, but maybe it will come apart easier if you do. In the HTC factory service video, they mentioned putting the whole phone into the oven to loosen the tape. I didn't know if it would be a good idea to do that complete with all the circuit boards or not.
No, without heat, the tape is definitely ruined and I will need to replace it. I was planning to use some leftover tape I have from fixing iPhone digitizers so I didn't even attempt to salvage the existing tape. Not sure if it's even possible to salvage that tape considering you need to stick some kind of tool in there to separate it.
Click to expand...
Click to collapse
Alright thanks I have to go and don't know when I'll be back, but I will try it tonight and hopefully I don't break anything...
Thanks for the help!