When you turn on the computer miniUSB then the E900, it recognizes the USB drivers, Zune does not start automatically. When I run zune manuel says " No device connected". Someone that some information or instructions on how to solve the problem.
Which USB driver are you currently loading? use the MFG application to load MS Composite driver, reboot the phone then connect it, you'll find all the info how to fire up MFG and change the driver on this forum.
Related
Hi there.
Just wandering.. I use Win7 Ult. 64-bit. And when I connect my HD2, it appears as an uknown device "Generic Serial" in device manager.
Trying to uninstall it, remove it, and restart pc, but doesn`t help.
Does anyone know how to fix this?
EDIT: Never mind. Win7 Ult. 64-bit does not come with "Windows Mobile Decvice Center" Dowloading latest WMDC (6.1 for 64-bit) solved the problem.
Sorry about the unnecessary post
Thank you
regards
Ztonez
Install, if it is "Generic Serial" run Windows Update. It downloads and install update and after reboot it´ll be OK
I don't have the "Generic serial" but have a "Bluetooth periferal device" with the yellow mark on it in my Win7 / HD2 installation, which I can not solve by running windows update.
Anyone has any ideas on hoy to fix that?
Posible fx
Try this:
Disconnect HD2 from PC, reboot pc
On de the HD2 go into settings -> connections -> USB to PC
UNcheck the "faster connection" thingy under active sync.
Press OK and when PC is rebooted connect the HD2 to an USB port you havent connected the HD2 to yet or use bluetooth. Make sure you have the lastest async/mob dev cent running.
let us know if it works
Good day today install W7 SP1 from MSDN and trying to connect my phone LG E900H "Telcel " only recognized as "Generic Serial" and installs the driver "Microsft USB Sync" but Zune does not sync, any idea?
Go to Device Manager, and uninstall whatever driver is assigned to your phone. Restart both your phone and computer, and run Windows Update again (or Zune update through the Zune Software) and make sure you have the latest version of Zune. Go to Services, and enable all three Zune services at the bottom. Then, connect your phone directly to a USB port on your computer (not a Hub), and let the driver install. It should bring up Zune Software as well. If that didn't work, uninstall the driver ( and make sure to tick the "delete driver" as well ), then run Zune, and connect your phone again. This should work.
I've had the following problem which I solved and now I'm wondering if anyone else found it, since I'm afraid it might point out to some hardware fault.
When selecting LG Software mode on the phone for connecting to your PC, Windows (in my case, 7 x64) attempts to install an MTP USB Device, but fails with Code 10: Device cannot start. At this point I (after many trial-and-error cycles) had to select Update Driver for that device in Device Manager, select Browse my computer for driver software > Let me pick from a list of drivers, and from the next screen, pick USB Composite Device instead of MTP USB Device. It installed right away and then 4 other USB devices popped up, which also were installed (using Windows Update). After this, LG PC Suite (and also LG Mobile Support Tool) detected the phone with no problems.
So, were any of you confronted with this?
Just wanted to say I had the same problems following your steps allowed me to get this to work. Thanked!
Thank you so much. This solved the problem.
I'm actually having this same issue. When I click "Show me a list of blah blah" it doesn't give me a USB Composite option. I only get two MTP options, and if I check "Show Compatible Hardware" it shows a bunch of drivers for MTP, WMP, and some other protocols. Any ideas?
gunnarizbeast said:
I'm actually having this same issue. When I click "Show me a list of blah blah" it doesn't give me a USB Composite option. I only get two MTP options, and if I check "Show Compatible Hardware" it shows a bunch of drivers for MTP, WMP, and some other protocols. Any ideas?
Click to expand...
Click to collapse
I am in the same situation, can you help how to fix this?
this problem fix?
I have a problem. Phone download mod work but I connect computer not connect phone. Says "This device can work faster". Device manager says yellow exclamation.
I try any computer but problem doesnt fix.
metalboy94 said:
I've had the following problem which I solved and now I'm wondering if anyone else found it, since I'm afraid it might point out to some hardware fault.
pick USB Composite Device instead of MTP USB Device. It installed right away and then 4 other USB devices popped up, which also were installed (using Windows Update). After this, LG PC Suite (and also LG Mobile Support Tool) detected the phone with no problems.
So, were any of you confronted with this?
Click to expand...
Click to collapse
yes, but unfortunately i don't have USB Composite Device as a selection on Windows 7 64bit. any other suggestions to get this stupid lg software installed?
After spending over 6 hours on this problem and installing a new windows, I finally found the culprit, it was Xposed Media Scanner, disabling it fixed the problem. Of course if you did not install this module before then the solution is not for you, maybe it will help someone reaching this page from Google.
I have downloaded the proper set of shield drivers.
I have set the shield to enable developer and debugging is on.
When I connect the shield to my Win 7 PC it shows up as an unknown device.
Now when I go to the device manager and try to update my driver for said device with my disc, Windows reports that the latest driver is installed.
I've also tried to right click on the .inf file but it will not install.
It seems that my problem is that the Shield is no showing up as something other than an unknown device.
Suggestions please
TNX
Having the same issue here; windows 10 keeps forcefully installing the "generic drivers". When I try to right click and update, it says the generic drivers are the best option (they're not!). Unfortunately the generic drivers wont show up on adb devices also..
did any1 resolve this
Hi
I am a new user for nexus 6p, For the first time I connected my device to Computer running windows 10 updated. My laptop didn't detect the usb and the driver is not installed properly, I tried downloading the latest usb driver but it didnt help , While searching for the driver folder it throws
Windows was unable to install your unkown drive
You can get the USB drivers straight from Google and try to uninstall/reinstall or download Wugfresh's NRT. There is very good driver installation tool and test to confirm you get both USB and fastboot drivers installed properly. Just follow the "Full Driver Installation Guide"
Tonyjaqs92 said:
Hi
I am a new user for nexus 6p, For the first time I connected my device to Computer running windows 10 updated. My laptop didn't detect the usb and the driver is not installed properly, I tried downloading the latest usb driver but it didnt help , While searching for the driver folder it throws
Windows was unable to install your unkown drive
Click to expand...
Click to collapse
Hi... Do you have ADB enabled in developer options? If you don't have developer options enabled, go in: settings>about phone and type 7 times on the build number, then go back in settings > developer options and enable "android debugging".
Plug your N6 on your computer, check your phone screen and allow press ok when it asks to "allow USB debugging".
Does it change something? Is your N6 recognized in device manager? Does the driver updates?
...
So My puter recognizes my phone fine....
Pop opened the configuration and General tab says:
This device is not configured correctly. (Code 1)
A service installation section in this INF is invalid.
To find a driver for this device, click Update Driver.
I try and update the driver using the "Let the puter search" feature and it finds one and tells me:
Windows encountered a problem installing the driver software for your device.
Windows found driver software for your device but encountered an error while attempting to install it.
MPE Device
A service installation section in this INF is invalid.
If you know the manufacturer of your device, you can visit its website and check the support section for driver software.
This is all AFTER I downloaded the latest Google USB drivers and unzipped them.
Phone is set to MTP mode and debugging mode is unlocked and usb debugging is on.
No Go.