Looking for help... X10 bricked and tried everything. - XPERIA X10 General

Hi,
About a week ago I checked my Rogers X10 to see if there was any software update. It said that I had the most current version. I went to hit the ok key and instead hit the key to reload software. It started to reload and then crashed part way through.
I tried to repair with PC Companion but it crashes near the end of the repair and says retry or contact support. The retry did not work.
I tried through SEUS to load the software and it gets near the end and aborts.
I tried flashing with the 2.9.1 flashtool and the 3.0 flashtool no luck.
I tried firmware X10a generic .435. It aborted part way through the flash.
I tried the X10a AT&T gingerbread firmware. It flashes and says completed, unplug, start your X10, etc. The first time it did this the AT&T world screen starts to come up and then reboots and gets stuck in a constant reboot cycle. I tried flashing again and it aborted. I went to PC Companion and tried repair again and it aborted. I tried 2.9.1 flashtool and tried the gingerbread flash again and the 2.1 generic flash. The 2.1 aborts, the gingerbread says it loads but when you power up, you feel the vibrate like a normal power on but the screen stays blank. If you try to reflash gingerbread twice in a row it aborts the second time. generic .435 aborts everytime.
I have tried every combination of PC Companion repair and update, SEUS update, Flashtool's and firmwares I can think of. The best I can do is to get the gingerbread to say it loaded fine but it will not boot. Everything else aborts in the update or flash stage.
ANY HELP would be appreciated.
Thanks

wotanserver
http://www.wotanserver.com

Update Service
Use Update Service not PC companion. If Update Service does not work, re-install it and try again. should work. downlaod link i could find: http://sony-ericsson-update-service.en.uptodown.com/download
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Devin-J said:
Use Update Service not PC companion. If Update Service does not work, re-install it and try again. should work. downlaod link i could find: http://sony-ericsson-update-service.en.uptodown.com/download
Click to expand...
Click to collapse
he already tried Update service (SEUS) (Sony Erricsson Update Service)
Reds4ever said:
Hi,
I tried through SEUS to load the software and it gets near the end and aborts.
Thanks
Click to expand...
Click to collapse
those probably phone hardware issue. SE service center might able to solve this.

Related

[Q] Errors while using Odin

What was my original post is not relevant anymore. Im stuck with a AT&T logo after using the odin3 one-click downloader. http://forum.xda-developers.com/showthread.php?t=731989
Somebody who can help me with this would be SUPER nice.
what does that Asian looking error message say?
seems like you are having some windows problem, it's probably missing some files
ok..ok but what? Should I reinstall Samsung drivers? (I have KIES installed)
I just updated my windows this morning.. anything to do with that?
Appreciate the reply.. but need a little more direction at where to go.
ok guys got a new problem. After searching for hours I found a thread wich contained the *solution* I thought was I looking for. It was the odin3 one click downloader (http://forum.xda-developers.com/showthread.php?t=731989)
Ofcourse that was about american i9000 phones and not for my phone. So now im stuck with a phone that doesnt do anything besides showing a AT&T logo for 5 seconds on and off.
anyone that can help me. Or did I just majorly f*ck it up?
Im also getting this problem, but I was able to flash my firmware to JM5 after a couple of retries, still unable to narrow down the real problem.. there are times I can reflash or get this error with the very same firmware.. what gives?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
download a JG8 rom from samsungfirmware website, and then use Odin3 to flash it again in Download Mode
remember to select repartition and use the 512 pit file
These errors seem to be pretty random, for the past week I was able to flash w/o seeing this error and now its back again.. Im currently at JM2 right now and I need to flash back to JG6 w/c i cant since im getting the error again.. anybody know what that error above means ?
EDIT:
Right now im using WXMJ2, flashing to XFJM6,JG8,JG5,JM5 gives me the above error.. already tried it all of my USB ports, power cycled the phone and the computer.. I am able to reflash JM2 over and over ( sometimes I get the error ) my battery level is at 95%, any know a fix or whats causing this error ?
Heres how I normally flash w/c has been going great since the past week execpt today, put the phone in download mode, run odin and select the required files and tick repartition, connect the phone and click start when a com# appears.
Is this some sort of big mystery ??

[Q] BIg problem

I tried to instal new room when i finised i have bootlop an i try to go to recovery but not working,then i tried seus but teling me that i have latest software and no repair buton instal anyway this buton is gone what to do .I am on stock kernel so wat to do is ther any way to instal stock room or whatt help meee
Repair with PC Companion
http://www.sonyericsson.com/cws/sup...oads/subject/pccompanion/xperiax8?cc=gb&lc=en
I cant pc companon want to turn the phone but i cant turn the phone becouse wont bot only sony ericson leters
Go to PC Companion > Click on Support Zone > Click on Repair.
Click on a blue link "repair your phone" (or something like that)
It will download all the necessary stuff and ask you to put you phone in flash mode.
Flash mode: turn off your phone, press back button while you plug the USB cable. The green led will turn on.
Just wait until the process finish. Unplug the USB and your phone will be rebooted.
help i cant repair seus no pc compainon no its said ,seus you have latest software, pc companion ther is no new software yet for your phone
Haha I was about to help then somebody else did.
Just note, afted this you have to root your phone all over again. Back at where you started. Remember to fully understand things before doing it, or it could cause a lot of troubles and time wasting!
Hit the THANKS button if I helped you!
This mail was delivered from my W8 using Tapatalk!!
no it wont i click repair evrithing is starte preparing hold back key an then ther is no software upate ,i tried to flash this room [X8] Achotjan Semc Debrand Engine | V1.0_Beta1 | FreeXperia Project and now i am stuck please help
When you run PCC, left your phone unplugged. The software will not identify the phone, so you have to click on this link as I show in screen below:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
yes i did an then this after prepering to repair this room is messed my phone http://img11.imageshack.us/img11/7344/capturexti.png
hunn.. for me always work... it download software, prepare, then you plug phone, it install and finish.
i dont know about/why this error, sorry
yes for mee to always worked but now stuck after this room
wotanclient 350 save my ass
this app flashed me new firmware you have to register and you have one poen to do firmware on the phone.Atlast my phone is working again
Relax that is a soft brick and very simple to fix.
PCC and sues won't work for most people. You will need to download and repair with flashtool. Download the x8 ftf file and flash. Just Google xperia x8 softbrick to find the thread with the downloads, I would do it for you but I'm on my phone.
Sent from my XPERIA X8 using xda premium

Stuck on emergency recovery screen T-380

Hi everyone. While I was attempting to root my tablet I ran in to a problem. It turned out since I had updated to 8.1 it had an RMM state that's prenormal, which makes it impossible to root. I found a guide to use Miracle Box to downgrade it to 7.1 where I'd be able to root. However in this process when I saw Miracle Box was done I decided to unplug the tablet. Well it turns out the tablet was still loading it, so unplugging it caused an error. Now whenever it boots up I'm stuck on the error screen which says to use the emergency recovery mode on smart switch. Well, smart switch won't find my device. Neither will kies. I've tried downloading 2 different stock roms for my exact device and using odin to install them, but I get an error on odin and it fails. I have tried two different versions of odin too, 3.12 and 3.13.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Here's the log and error I'm getting.
Here's my tablet screen.
I have no idea what else to do here to get my device back in usable state. Please help!
Smasher39 said:
Hi everyone. While I was attempting to root my tablet I ran in to a problem. It turned out since I had updated to 8.1 it had an RMM state that's prenormal, which makes it impossible to root. I found a guide to use Miracle Box to downgrade it to 7.1 where I'd be able to root. However in this process when I saw Miracle Box was done I decided to unplug the tablet. Well it turns out the tablet was still loading it, so unplugging it caused an error. Now whenever it boots up I'm stuck on the error screen which says to use the emergency recovery mode on smart switch. Well, smart switch won't find my device. Neither will kies. I've tried downloading 2 different stock roms for my exact device and using odin to install them, but I get an error on odin and it fails. I have tried two different versions of odin too, 3.12 and 3.13.
Here's the log and error I'm getting.
Here's my tablet screen.
I have no idea what else to do here to get my device back in usable state. Please help!
Click to expand...
Click to collapse
What error are you getting? There is no picture of your tablet or the error. Also did you try patched Odin? If SmartSwitch won't recognize it do you have the samsung USB drivers installed from here? https://developer.samsung.com/mobile/android-usb-driver.html

Issues returning to stock

Howdy everyone...
OnePlus 7t Pro McLaren edition (International Edition **NOT T-MOBILE**)
Model: HD1913
Current Software Build: Oxygen OS 10.0.5.HD01AA (OTA update when I first unboxed).
I am having issues trying to return to stock. I rooted the phone with a combination of a couple guides found here (https://forum.xda-developers.com/7t-pro/how-to/10-0-3-patched-boot-image-oneplus-7t-pro-t3986351 and . I noticed after doing that I was missing the stock Oxygen apps and my build information was missing data. Not a huge deal, but I need to wipe the phone and start from scratch anyway, for other reasons. I decided to go back to stock if I have to redo everything anywhere.
First thing I tried, I got the stock firmwares (https://forum.xda-developers.com/7t-pro/how-to/oneplus-7t-pro-repo-oxygen-os-builds-t4003455). And this is where my issues started. My software build is weird... I have the HD1913, however my software build is HD01AA. Per that post, I should have HD01BA. I grabbed both of them for giggles, put them on my storage and booted into TWRP. Tried to flash the HD01AA (since that was what I have now), and it failed. Tried the other one, same issue. I'm getting a bunch of errors while trying to mount the system ("System unable to mount: invalid argument").
Second thing I tried, was to use the built in software update that OnePlus says to use (through the system update). It wouldn't install them (surprise).
Third attempt... Using the MsmDownloadTool (https://forum.xda-developers.com/7t-pro/how-to/op7tpro-unbrick-tool-to-restore-device-t4002909) I downloaded both versions cause I don't know which to use, and followed the instructions to get the phone into the mode. Turn the phone off, hold the vol up button and plug the cable in (very simple). It shows up connected in the software. Exactly 5 seconds later, the phone reboots and boots normally... I repeat this process aprox. 2.3 million more times. It does not matter what USB-C cable I use, the port on my computer, or how long I hold the buttons. The phone will boot into the download mode (or whatever it's called) show up as connected in MsmDownload and then reboot.
The phone works. I am still able to boot it up.... All I want to do is get this phone back to stock. I don't HAVE to, but now that it's fighting me, I have to beat it...
imgur.com/a/KhBGwao
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Okay - After sacrificing an iPhone to the Android God, I got it.
Instead of using the button combination to get into EDL Mode, I found an article that gave an adb command (adb reboot edl) to get to it. It did not reboot this time, and I was able to flash HD01BA to it, which matches what the phone should have...

Custom Binary (SYSTEM) Blocked by OEM lock

hey guys i recently had an update on my s10+ and mid through the update the phone just powered off(it was plugged to the charger) and since then ive been stuck on a blue screen saying i have to use the emergency recovery function in the smart switch pc app so i downloaded the app and tried to do that but the app wont recognize my phone. i searched all over the internet i tried flashing with odin a previous version and even the version it was trying to update to but it all failed. it gets stuck around 50% through the install and just sits there for hours without continuing. i am hopeless and have no idea what else i can do i even took the phone to a repair shop and they also failed to fix this problem. my last resort would be changing motherboard but i doubt its worth it. anyone has ideas what else i can do in order to fix this issue?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Are you able to get in to oden mode Google this to see how it's done.....
Sent from my CPH1951 using Tapatalk
stinka318 said:
Are you able to get in to oden mode Google this to see how it's done.....
Sent from my CPH1951 using Tapatalk
Click to expand...
Click to collapse
no i am unable to get into download mode i tried everything possible but the phone wont respond its stuck on a blue screen saying " An error has occurred while updating the device software. use the Emergency recovery function in the smart switch pc software.
also the phone only power on when its plugged to charger or a pc but it has battery for sure
Here is something to try......no guarantee.
https://drfone.wondershare.com/android-issue/android-blue-screen-of-death.html
Sent from my CPH1951 using Tapatalk
stinka318 said:
Here is something to try......no guarantee.
they dont have the latest phones on their list. latest version available they have is s9 plus
Click to expand...
Click to collapse
MrJoni94 said:
stinka318 said:
Here is something to try......no guarantee.
they dont have the latest phones on their list. latest version available they have is s9 plus
Click to expand...
Click to collapse
Email them to see if they can help in some way not sure if they'll can but it is worth a try but as I said no guarantee.......
Click to expand...
Click to collapse
Not sure if you've tried this but maybe it will work...
1) Hold bixby, volume down and while holding these, put the usb-c cable in the s10 when connected to the PC. This will (hopefully) get you into download mode if the other method fails
2)If Odin is still recognizing your phone, you have hope.
3)Make sure you use the latest version of Odin. I have previously tried to flash a new firmware with an old Odin and failed
4)Once you have the right Odin, try flash the latest stock firmware you can find. You may not be able to downgrade once upgraded

Categories

Resources