Hi, when i try update ROM (http://forum.xda-developers.com/showthread.php?t=1236027) (from 7008 to 7392) after 2% backup Zune show restarting and give me error 801812DC. I try it with 2 different sd card and with 2 PC and always same error.
Anybody can help? Thanks
Yea I had that. Uninstall Zune before you do this update. Delete the contents of the Zune folder in Program Files, then reinstall zune and run the update again.
nikc0069 said:
Yea I had that. Uninstall Zune before you do this update. Delete the contents of the Zune folder in Program Files, then reinstall zune and run the update again.
Click to expand...
Click to collapse
Thanks, but no luck with that. Still show error. Any other idea?
EDIT: And after last atempt to update (after error) phone stuck on SIM Pin page and I must do 3 hard reset.
Ok, I try it now again and now backup status stuck on 1% and again resrart and error, and again freeze PIN page...
Does it work if you don't use a sim that requires a pin?
nikc0069 said:
Does it work if you don't use a sim that requires a pin?
Click to expand...
Click to collapse
No it stuck on another (first screen after start)
EDIT: Now I try completly instal WP7 again (WM 6.5, Radio ROM, MAGLDR, try also radio ROM 5.51T..., still show update error and still freezing)
This is a bad rom,I will wait some better, it is full errors.
glorfindel.mladenovic said:
This is a bad rom,I will wait some better, it is full errors.
Click to expand...
Click to collapse
Yeah, me to. I don't think this is bad ROM but after 3 days of testing I need working phone so i must go back to android...
Related
Ok my last 3 days I've been simply trying to install some custom ROMs and did all the reading and research step by step, but my AT&T HTC Pure just wont update the HSPL no matter what.
Steps I've taken so far:
1. Formatted SD Card
2. Obtained and put goldcard.img on SD Card
3. Fully connected phone via Windows Mobile Device Center
4. Antivirus turned off
5. Tried Topaz-HardSPL_V5_00R5_183HSPL in in auto-mode, fails telling me " Fatal Error" and underneath "Please make sure the device is properly synced; Please retry after syncing device (via Activesync or Windows Mobile Device Center)" which I have...
6. Tried installing ENABLERAPINEW.cab with results "unsuccessful" (but again my phone does sync just fine, I still took this step)
7. Tried Manual Flash, my phone never goes into bootloader, and right after "verifying phone information" shows screen saying "ERROR [224]: DEVICE NOT RESPONDING"
8. Tried entering bootloader mode and during auto-mode to flash, tells me same exact thing as without bootloader
9. Tried Manual Flash in bootloader, it gets to flashing screen with a progress bar at 0% on both PC and phone forever, I waited 20 mins and it didn't change.
It seems as if there is something preventing RUU to be writing anything on my phone, so that's why it throws connection error, but I am not sure. And I am seriously loosing all hope in this and dont know what to do, so HELP please!
Update
I also forgot to mention that I tried to Hard_SPL from another computer that is Windows XP, used Activesync, which didn't work either...
The only thing i can tell you is to read this thread (what you have already done i think)
http://forum.xda-developers.com/showthread.php?t=520312
SerGTR said:
Ok my last 3 days I've been simply trying to install some custom ROMs and did all the reading and research step by step, but my AT&T HTC Pure just wont update the HSPL no matter what.
Steps I've taken so far:
1. Formatted SD Card
2. Obtained and put goldcard.img on SD Card
3. Fully connected phone via Windows Mobile Device Center
4. Antivirus turned off
5. Tried Topaz-HardSPL_V5_00R5_183HSPL in in auto-mode, fails telling me " Fatal Error" and underneath "Please make sure the device is properly synced; Please retry after syncing device (via Activesync or Windows Mobile Device Center)" which I have...
6. Tried installing ENABLERAPINEW.cab with results "unsuccessful" (but again my phone does sync just fine, I still took this step)
7. Tried Manual Flash, my phone never goes into bootloader, and right after "verifying phone information" shows screen saying "ERROR [224]: DEVICE NOT RESPONDING"
8. Tried entering bootloader mode and during auto-mode to flash, tells me same exact thing as without bootloader
9. Tried Manual Flash in bootloader, it gets to flashing screen with a progress bar at 0% on both PC and phone forever, I waited 20 mins and it didn't change.
It seems as if there is something preventing RUU to be writing anything on my phone, so that's why it throws connection error, but I am not sure. And I am seriously loosing all hope in this and dont know what to do, so HELP please!
Click to expand...
Click to collapse
you cant flash hardspl on the sd card, it must be done over activsync. u dont put it on your card, you run it from your computer. make a new folder{on your computer} and name it whatever , then unrar the file into the folder, then you should be able to flash the hardspl.make sure the ruu and the nbh file are in the folder.
leemoss84 said:
you cant flash hardspl on the sd card, it must be done over activsync. u dont put it on your card, you run it from your computer. make a new folder{on your computer} and name it whatever , then unrar the file into the folder, then you should be able to flash the hardspl.make sure the ruu and the nbh file are in the folder.
Click to expand...
Click to collapse
I do run Custom RUU from desktop local drive and not from SD Card and results mentioned above are the ones I get. Again tried with phone on, it just tells me ERROR [224] and never goes into bootloader or anything. Tried entering the the phone to bootloader manually and connecting it to usb and run RUU, it goes a little further where it finally gets to screen of flashing progress but freezes at 0% and thats it.
Could missteps in obtaining Goldcard be the reason for such behavior?
leemoss84 said:
you cant flash hardspl on the sd card, it must be done over activsync. u dont put it on your card, you run it from your computer. make a new folder{on your computer} and name it whatever , then unrar the file into the folder, then you should be able to flash the hardspl.make sure the ruu and the nbh file are in the folder.
Click to expand...
Click to collapse
Yes, you can flash ANY .nbh from your SD card by renaming it TOPAIMG.nbh.
SerGTR said:
I do run Custom RUU from desktop local drive and not from SD Card and results mentioned above are the ones I get. Again tried with phone on, it just tells me ERROR [224] and never goes into bootloader or anything. Tried entering the the phone to bootloader manually and connecting it to usb and run RUU, it goes a little further where it finally gets to screen of flashing progress but freezes at 0% and thats it.
Could missteps in obtaining Goldcard be the reason for such behavior?
Click to expand...
Click to collapse
Sorry for my ignorance but what is goldcard?
What is the current SPL?
I agree leemoss. You need Hardspl from your system. First synch your phone to system through Active sync. Execute the HardSpl.183, select auto flash.
Second thing i noted is on SDcard you have to rename the ROM file and store it as TOPAIMG.nbh and place in the root folder.
I read about people having problems, and the ones that weren't spent the 20 bucks on the Sim unlocker. I'd never flashed a phone before, so I went that route. It's worth it IMO.
rbrsddn said:
I read about people having problems, and the ones that weren't spent the 20 bucks on the Sim unlocker. I'd never flashed a phone before, so I went that route. It's worth it IMO.
Click to expand...
Click to collapse
See I do take ever single step that is in the guide here:
http://forum.xda-developers.com/showthread.php?t=530335
But it just doesnt work, but again I flashed HSPL and custom ROMs before on my Xperia X1a (unlocked) without any problems. I attached a pic of my bootloader, and when I try to run some custom ROM which I name TOPAIMG.nbh it enter screen "loading..." and freezes so have to rest my phone by taking battery out so it loads back just fine.
Again this phone I am using is HTC Pure by AT&T and thats what confuses me, maybe I really do have to SIM unlock my phone before I can HSPL and flash custom .nbh ROMs?
gold card
Bruce Inman said:
Sorry for my ignorance but what is goldcard?
What is the current SPL?
Click to expand...
Click to collapse
My stock SPL is in pic attached, and Goldcard.img suppose to be something I had to put on my SD Card so that I have SuperCID so I can flash HSPL and any custom ROMs, you can read more about it here: http://forum.xda-developers.com/showthread.php?t=530335
SerGTR said:
See I do take ever single step that is in the guide here:
http://forum.xda-developers.com/showthread.php?t=530335
But it just doesnt work, but again I flashed HSPL and custom ROMs before on my Xperia X1a (unlocked) without any problems. I attached a pic of my bootloader, and when I try to run some custom ROM which I name TOPAIMG.nbh it enter screen "loading..." and freezes so have to rest my phone by taking battery out so it loads back just fine.
Again this phone I am using is HTC Pure by AT&T and thats what confuses me, maybe I really do have to SIM unlock my phone before I can HSPL and flash custom .nbh ROMs?
Click to expand...
Click to collapse
You only need to CID unlock to flash ROMs, if you buy the SIM unlocker you get both CID and Security unlocked but it still may not work.
I see you have 1.8.33 which is good because there is not a working HSPL for 2.54
You say you tried running custom ROMs as TOPAIMG.nbh, but did you try it with the HSPL nhb? It would be the same process as doing a ROM from SD card.
I would also get rid of goldcard as that is only to recover a bricked device.
Get all goldcard stuff off your card and PC, reformatt your card to Fat32 the place the renamed TOPAIMG.nbh and proceed to bootloader.
One last pointer, another method to flash is to download Topaz Custom RUU Wrapper and put the exe file in the same folder as the .nbh on your desktop and run the .exe after your sync'd. **Make sure all firewalls and antivirus are off.**
Good Luck.
Bruce Inman said:
You only need to CID unlock to flash ROMs, if you buy the SIM unlocker you get both CID and Security unlocked but it still may not work.
I see you have 1.8.33 which is good because there is not a working HSPL for 2.54
You say you tried running custom ROMs as TOPAIMG.nbh, but did you try it with the HSPL nhb? It would be the same process as doing a ROM from SD card.
I would also get rid of goldcard as that is only to recover a bricked device.
Get all goldcard stuff off your card and PC, reformatt your card to Fat32 the place the renamed TOPAIMG.nbh and proceed to bootloader.
One last pointer, another method to flash is to download Topaz Custom RUU Wrapper and put the exe file in the same folder as the .nbh on your desktop and run the .exe after your sync'd. **Make sure all firewalls and antivirus are off.**
Good Luck.
Click to expand...
Click to collapse
Tried still same results... freezes at flashing with 0% at progress bar. I attached view screens that concern me that RUU cant read my stock ROM Image version, is this normal? The only other thing I am gonna try to do is maybe reinstall the entire Windows Mobile Device Center, besides that I am clueless.
Have you install the enablerapinew.cab first?
If so, I'm outta tricks. Others have been having issues as well in the HSPL thread. You may have to wait for an update.
I don't think its anything on your PC unless firewall or AV aren't turned off.
Remove SD-Card and Sim-Card before HardSPL from PC. I had 2 TouchDuals before TD2, one was no prob to flash, second needed SD-Card to be removed! Once HardSPL succeeded you may leave SD-Card in TD2.
WORKING!!!
YES!!! I finally got it to SPL, what it was that my phone could not accept any .cab installations due to security issue with "unknown publisher" signature, that's why my phone didn't allow me to install enablerapinew.cab but then I just hard reset my phone installed enablerapinew.cab and everything worked, YEY! Thank you Bruce Inman, and everyone else who spend time to try to guide me through my issues, tnx!
i didnt unlock mine. all i did was flash it.theres gotta be sumthn ur doin wrong.
Problem solved!
leemoss84 said:
i didnt unlock mine. all i did was flash it.theres gotta be sumthn ur doin wrong.
Click to expand...
Click to collapse
I figured it out man, tnx.
SerGTR said:
I figured it out man, tnx.
Click to expand...
Click to collapse
good deal man. what was the prob?
leemoss84 said:
good deal man. what was the prob?
Click to expand...
Click to collapse
What it was that my phone could not accept any .cab installations due to security issue with "unknown publisher" signature, that's why my phone didn't allow me to install enablerapinew.cab but then I just hard reset my phone installed enablerapinew.cab and everything worked.
hi guys,
im attempting to update my hd2 but cannont. i sync it with active sync, start the update and it changes the phone to the tri color screen, but immediately disconnects on the computer, and a 1 minute later i get the error [260] connection screen.
can anyone assist me with updating? i also heard there is a way to update from the memory card...that might be the best way for me if someone can help me with that. THANKS
trexxcrap2 said:
hi guys,
im attempting to update my hd2 but cannont. i sync it with active sync, start the update and it changes the phone to the tri color screen, but immediately disconnects on the computer, and a 1 minute later i get the error [260] connection screen.
can anyone assist me with updating? i also heard there is a way to update from the memory card...that might be the best way for me if someone can help me with that. THANKS
Click to expand...
Click to collapse
What are you trying to update it to?
secano said:
What are you trying to update it to?
Click to expand...
Click to collapse
the new update that came out a few days ago....
trexxcrap2 said:
im attempting to update my hd2 but cannont. i sync it with active sync, start the update and it changes the phone to the tri color screen, but immediately disconnects on the computer, and a 1 minute later i get the error [260] connection screen.
Click to expand...
Click to collapse
Here is a link to the error codes. Your error means you need to go back to SSPL before you can flash that ROM.
trexxcrap2 said:
i also heard there is a way to update from the memory card...that might be the best way for me if someone can help me with that. THANKS
Click to expand...
Click to collapse
Here is a link to my tutorial on how to flash via SD card.
i am having the same issue each time i attempt to update my rom. error 260.
jenelson said:
i am having the same issue each time i attempt to update my rom. error 260.
Click to expand...
Click to collapse
You are still using the original SSPL (Soft Second Program Loader) which will only accept official update ROMs.
In order to flash the custom ROMs available here, you will need to flash in a HSPL (Hard Second Program Loader).
I don't know if you are totally new to flashing ROMs or not, since you didn't say and your post indicator said that was your first post here, but I would advise you to be very, very careful. In the early days (last month, actually) a TON of people were bricking their phones because they accidentally downloaded the European ROMs for the 512Leo. Ours is the 1024Leo and only ROMs designed for our phones will work.
The phone I am using is actually a replacement from TMO. I was having issues with the original device I purchased.
How do I use a HSPL or whatever... I am slightly confused but I can catch up quickly...
Thanks.
same thing happened to me, what i did was i restarted the update without disconnecting the phone from the computer, and it worked.
nyaznteen said:
same thing happened to me, what i did was i restarted the update without disconnecting the phone from the computer, and it worked.
Click to expand...
Click to collapse
I encountered the same problem and it appeared that my computer was slow in "re-recognizing" the phone. For some reason, it had to reinstall drivers before continuing with the update. After the device was again recognized, I restartde the update (without disconnecting the phone) and it continued without issue.
I had been worried that the phone had become a paperweight when I saw the tricolor screen, but everything has been fine and the upgrade appears to have worked correctly.
jenelson said:
The phone I am using is actually a replacement from TMO. I was having issues with the original device I purchased.
How do I use a HSPL or whatever... I am slightly confused but I can catch up quickly...
Thanks.
Click to expand...
Click to collapse
Think of HSPL as your BIOS (it isn't, but it may help you to think of it as such). You don't have any control over the options, but you need it to load or install your OS. Installing HSPL is simply a matter of following the directions in the link that I posted last time: http://forum.xda-developers.com/showthread.php?t=653614
Once you have HSPL installed, you should be able to "flash" any ROM. Of course, this also allows you to flash ROMs that are not meant for your phone, so that's the danger behind it.
When you visit a thread that offers a ROM, it should either have instructions or a link to instructions on how to install. If it does not, a google search for "xda how to install a custom rom" should give you a million helpful links. (This is actually beyond the scope of this post so I won't go into details)
Hope this helped some...
Same problem but i have hspl?
not sure what im doing wrong here I've installed hspl 1.42 which was enough trouble for what seemed like a pretty straight forward job. now whatever i try to install all i get is error 260? on top of this i don't seem to be able to send message tho i can receive and the camera on my phone no longer seems to work?
i am a newbie but Ive been reading and clicking and trying to install stuff for hours and hours and so far all Ive managed to do is install hspl and reduce my phones usability.
i got windows mobile device center 6.1 tried it with and without allow usb connections.
my antivirus and firewall is off.
.net framework 4 installed.
tried different usb ports
ive tried installing Duttys_Leo_Sense_2.5_5.23569.5.5.0_2.14_Holy_Grail_576MB_V4.3_WWE and a stock rom
my computer has vista 64 on it.
im hoping im just being a bit dense here please help me i just wanna join in on all this flashing fun!!
mumbles85 said:
not sure what im doing wrong here I've installed hspl 1.42 which was enough trouble for what seemed like a pretty straight forward job. now whatever i try to install all i get is error 260? on top of this i don't seem to be able to send message tho i can receive and the camera on my phone no longer seems to work?
i am a newbie but Ive been reading and clicking and trying to install stuff for hours and hours and so far all Ive managed to do is install hspl and reduce my phones usability.
i got windows mobile device center 6.1 tried it with and without allow usb connections.
my antivirus and firewall is off.
.net framework 4 installed.
tried different usb ports
ive tried installing Duttys_Leo_Sense_2.5_5.23569.5.5.0_2.14_Holy_Grail_576MB_V4.3_WWE and a stock rom
my computer has vista 64 on it.
im hoping im just being a bit dense here please help me i just wanna join in on all this flashing fun!!
Click to expand...
Click to collapse
just for kicks did you try a different ROM, find another ROM that is Compatible and try it, not saying there is anything wrong with Dutty's , but could just be the download , but not sure since you tried stock too ...
You may need to reinstall HSPL3, if you tried to flash a stock rom, and even if it failed it could have removed HSPL ...
Also try plugging the USB cable into the back of the machine
error 260 1024hd2
Hey guys,
I am having the same issue although I may know the answer but not sure how to fix it. Prior to flashing chuckyRom, I installed HSPL but I don't think I installed the correct version (still worked). So does anyone think this entire problem is attributed to initially installing the wrong hard SPL. If so, how can this be fixed? android is running great on chuckyRom but it would be nice to use a rom that is used for more than running android.
Please help, I have been in misery trying to solve this for over two weeks now.
Error 260, T-mobile HD2
Error 260 during ROM update
I had the same problem and tried everything (?)
Finally I got it work.
After I started the update the first time, I got the message, driver was not installed successfuly ...blabla
I ignored the message, tried and the connection disconnected every time again.
At the end I used another usb port and it asked me to download the CDMA driver. After download and installation, the update was in 5 min. done
Snarksneeze said:
You are still using the original SSPL (Soft Second Program Loader) which will only accept official update ROMs.
In order to flash the custom ROMs available here, you will need to flash in a HSPL (Hard Second Program Loader).
Click to expand...
Click to collapse
He was trying to install the OEM rom. I'm doing the same and have the same issues.
Error 260 on Htc Hd2 running windows mobile 7
I cannot get data on my hd2 when I installed win7 so I wanted to downgrade the os back to 6.5 but I get Error 260 when I connect to my phone to my cpu via usb. Is there a work around?
Dizzle88 said:
I cannot get data on my hd2 when I installed win7 so I wanted to downgrade the os back to 6.5 but I get Error 260 when I connect to my phone to my cpu via usb. Is there a work around?
Click to expand...
Click to collapse
Put the phone into BootLoader Mode then connect to the PC. Run the ROM.
Error 260 connection in HTC HD2
Dear all;
i have this problem in windows 7 each time i connect my phone with pc it gave me error 260 , so when i connect the usb cable i choose the first choice sync not the default one storage and it worked for me .
Ahmed Hosni
thanks for the note
fred_up said:
Put the phone into BootLoader Mode then connect to the PC. Run the ROM.
Click to expand...
Click to collapse
First time flashing the radio and kept getting error 260 from CustomRUU.
Read so many threads and all say sync the phone with your PC and run CustomRUU. Nobody said to run it under BootLoader Mode.
This simple note helped a lot for a newbie like me.... thanks
Error [260]
Hello
I want to try to update my HD2 from 2.2 to 2.3.x but I always geht thr Connection error.
I´ve flashed my HD2 from Windows Mobile 6 to Android.
I thank you for your help.
Ok, so I went to flash a new ROM on my phone, and when I go to the run the RUU, I get the screen with the 4 steps to complete, which are already completed, then hit next. Now I get "Error [240] : File Open" and below that it says "The Update Utility cannot open the requested file. Please check the update utility."
I tried downloading the Update Utility again, but it still does the same thing. Ive flashed my phone before, and Im pretty sure Im not doin anything different this time, but its not workin. Am I missing somethin?
Thanks
new-b said:
Ok, so I went to flash a new ROM on my phone, and when I go to the run the RUU, I get the screen with the 4 steps to complete, which are already completed, then hit next. Now I get "Error [240] : File Open" and below that it says "The Update Utility cannot open the requested file. Please check the update utility."
I tried downloading the Update Utility again, but it still does the same thing. Ive flashed my phone before, and Im pretty sure Im not doin anything different this time, but its not workin. Am I missing somethin?
Thanks
Click to expand...
Click to collapse
Check if your harddrive isn't full.
A RUU extract some files, and if your harddrive is full it can't
Nope, its not full. Far from it actually lol.
new-b said:
Nope, its not full. Far from it actually lol.
Click to expand...
Click to collapse
flashing trough sd-card?
im having the same problem i get the error code as well, is it possble to flash from the microsd. I am a nooby at this and understand how to flash.
xmoo said:
flashing trough sd-card?
Click to expand...
Click to collapse
Nope, win mo device center.
WeaponX2010 said:
im having the same problem i get the error code as well, is it possble to flash from the microsd. I am a nooby at this and understand how to flash.
Click to expand...
Click to collapse
Its in the tutorial, but I havent tried it yet. Ive never had a problem flashing through the USB before.
Tried it from the SD card. Went great. Just takes a little longer.
Still open to suggestions about usin active sync though.
xmoo said:
Check if your harddrive isn't full.
A RUU extract some files, and if your harddrive is full it can't
Click to expand...
Click to collapse
Hi xmoo. Can YOU please help? With this:
leo70 said:
URGENT MAJOR HELP REQUIRED *PLEASE*:
I am stuck on DFT boot screen (after doing 1234-vol up_down-wp7-reset) and this is *after* (wp7 here !) all the chains b4 that are done: ie: power on, hspl, htc, magldr- for windows phone 7 on hd2. Sometimes get thru to windows phone 7. but generally reboots. Done spl back to stock and leoimg on sd back to stock and tried task28s, 29s, etc but just reboots constantly and randomly.
Any thoughts here? What is warranty process? DO they replace at all with NEW? or new BOARDS/RAM? Gone back to 1.66 spl and sent in for repairs. because - the stupid recommended Romupdateutility HTC stock rom 'upgrade' did this damage. yes, was Windows Phone 7 and activated using dev hack with marketplace & xbox/live. Also - although I activate ok and can use it on market fine once it boots good - still when both my hd7 (hd2) and Mozart are signed into XboxLive using same address at same time: (mozart is legit fully/eula-signed etc) then the hd2 seems to reset a LOT here at this point. maybe this has something to do with usual xbox-live security? ie: http://www.wpcentral.com/hack-xbox-live-windows-phone-7-get-perma-banned-microsoft ?????????? please hlp me - I am fully capable of mtty, sd-leoimg, whatever it takes- but need to know why this would be the case? same with Android roms/stock too. Anyone know about task2a on hd2? how many bad blocks I should have? partition/re-partition droid or wp7 to avoid these bad blocks? I just WISH Cotulla/DFT let you run the windows phone 7 installer in such a way that all bad bloks could be excluded totally as if the never exist... ie make hd2 clean.
Click to expand...
Click to collapse
note: although I have gone bak to original spl+rom in past I have (both unsuccs &succesfully) have previously done task2a and even spl-mfg install and radios/roms as DEBUG/SPL-MFG. xmoo?
What will be happening if I do install NoDo update over Zune on my HD2?
My Phone remember me all the time, like zune, that the new Update ist avaible.
I have think about it for two days, but I'm too cowardly. Have someone test it?
Or would it damage my WP7?
Your phone wil stop working if you do....then you have to redo everything
pteradactyle said:
Your phone wil stop working if you do....then you have to redo everything
Click to expand...
Click to collapse
no it wont,
it wont install, it will restart and will be just the same as normal, end of story
No update no problem
Tried it last week.
The software tried to set up and crashed when it tried to reboot the phone.
First time it stopped when the phone booted to Android (Magldr preference)
Changed preference and tried again
got to a screen (on the phone) showing a link between the PC and WP7, then after 5 min crashed out. Phone rebooted without any changes.
I am now patiently waiting on the good folks at DFT to finish creating a NoDo for my Leo.
dazza9075 said:
no it wont,
it wont install, it will restart and will be just the same as normal, end of story
Click to expand...
Click to collapse
O well, I'm out of WP7.
Hi,
I just installed WP 7 7004 on my way to Mango installation.
However, the phone is constantly resetting.
What could be the problem?
It could be caused by the SD card. Last time I went this route to load Mango, I left the SD card until I got the first two updates installed. There is some info on this in other posts.
appa73 said:
Hi,
I just installed WP 7 7004 on my way to Mango installation.
However, the phone is constantly resetting.
What could be the problem?
Click to expand...
Click to collapse
If you are starting out from 7004, do not reboot after the initial flash. Go straight into flashing the next set of cabs. Sounds like you're flashing Yuki/XBmod'a ROM.
hjhjhj said:
If you are starting out from 7004, do not reboot after the initial flash. Go straight into flashing the next set of cabs. Sounds like you're flashing Yuki/XBmod'a ROM.
Click to expand...
Click to collapse
yes, i am. thank you. i removed the SD card and re-flashed the ROM. Its working. However, I am trying to upgrade from 7004 to 7720 directly but unable to find
WP7-7004-7720-Patch.zip anywhere. The old multiupload locations are not working.
Do you know anywhere else i can find it?
appa73 said:
yes, i am. thank you. i removed the SD card and re-flashed the ROM. Its working. However, I am trying to upgrade from 7004 to 7720 directly but unable to find
WP7-7004-7720-Patch.zip anywhere. The old multiupload locations are not working.
Do you know anywhere else i can find it?
Click to expand...
Click to collapse
You can find all of Yuki/XBmod's cabs and xaps here.
http://xboxmod.sylvester20007.com
Go to http://xboxmod.sylvester20007.com/CABS/OSBUILD.CAB/ and use the 7004 to 8107 autoinstaller. This is a nonstop update installer except for a pause after the first set of installs...follow screen instructions once the installation starts.
Don't forget to flash SP1 cab once the above is completed.
hjhjhj said:
You can find all of Yuki/XBmod's cabs and xaps here.
Go to and use the 7004 to 8107 autoinstaller. This is a nonstop update installer except for a pause after the first set of installs...follow screen instructions once the installation starts.
Don't forget to flash SP1 cab once the above is completed.
Click to expand...
Click to collapse
Thanks once again, i did that and it worked fine till i flashed SP1 after 7720. I should have first got to 7740, but i flashed SP1 a step earlier.
Can I now go to 7740 and again flash SP1? Else how to undo SP1?
appa73 said:
Thanks once again, i did that and it worked fine till i flashed SP1 after 7720. I should have first got to 7740, but i flashed SP1 a step earlier.
Can I now go to 7740 and again flash SP1? Else how to undo SP1?
Click to expand...
Click to collapse
nope...have to start over again and flash from scratch...just flash sp1 last after 8107 mango finishes. you should not stop the flash going from 7004 to 8107...DO NOT INTERRUPT THE AUTOINSTALLER...JUST PRESS ANY KEY WHEN IT SAYS 'PRESS ANY KEY TO CONTINUE' TO FINISH THE INSTALL TO 8107.
THE TOTAL TIME TAKES ABOUT 1.5 HRS.
READ THE SUGGESTED FLASH ON THE 1ST POST ON YUKI'S FORUM.