I was wanting to put the uk3rom onto a previously orange branded phone.
I was told to boot up into recovery and flash the file splhard1_update_signed.zip.
Upon doing this my phone will now not start up?
I have also noticed that the charging light does not come on, when plugged in
(well no light comes on anyway)
I was asked to format the sd card and put DREAIMG.nbh on and then reboot using home and power/on. It didnt work
I took it to a local repairer but he said was bad flash and that it was now irrepairable. Another one, said it was beyond him *-(
I have since been told told that if i can find a repairer that uses ort jtag, they would be able to restore the boot,which will allow connection then 2 be made to pc. Then hopefully i can then flash original orange firmware back... is this possible guys?
Does anyone know of any such repairer in UK
cheers
Beano
how bout HTC they bfixed my bricked hero if they ask tell them it ran out of bat updating to 2.1
cool....
Do you happen to have any contact numbers for them in UK
How did you get on with yours?
thanks
Beano
Contact number is here htc.com/uk/CA_Hotline.aspx
Ummm, why were you flashing the spl for a dream?
And really if you do this, remember you're technically committing fraud, since you caused the damage to the handset yourself.
I am sure HTC will wise up to this "trick" pretty soon.
BTW, op, flash only hero roms on a hero. I'm sure you've discovered that now, but just reiterating.
If you can find the JTAG schematics for the Hero chipset, and find the right points it is possible to JTAG yourself.
You'll need an LPT port on a PC, HJTAG, NoICE Programs, some cable (I have previously used an LPT cable to JTAG a device) solder, some board to solder to, wire, resistors, and a logic chip.
If you're not up to that, which is possible due to the circumstances, buy a new phone, as you don't want to be commiting fraud now do you!
Now back in Canada, i sent off to HTC.
They advised me that they will perform the repair, but they have identified that a firmware alien to them resides on the phone. They suggested i invalidated my warranty but for 100 bucks, they see to it....
a hard lesson but one ill learn from...
thanks all
Stumbled upon this a bit ago, a company called Mobile Tech is offering an "unbricking" service on all versions of the Galaxy Tab. At the time of this writing they charge $50. I have not used this service, am not in any affiliated with this company and cannot vouch for their work, so beware. Just thought someone out there might use this when other options aren't available.
They have a nifty video up on youtube showing how they do it:
it will be a good help for those who brick their tab because they ain't follow the steps .. thanks for sharing this out
I can actually vouch third party for this service. Have had two friends use it and the device was returned within a few days. If I'm not mistaken, the guy lives in the southern US, but can arrange international he says.
Sent from my "better than an iPad" tab... Running Overcome GINGERBREAD!!!
This is cool, but I would recommend trying to go through Samsung first if you are still under warranty. I screwed up my primary bootloader and contacted them. They took care of shipping costs, fixed it up, and sent it back in about a week and a half. If Samsung hadn't fixed it I would defiantly have payed the $50 here though.
WOW, that seems like a lot of work for $50.
Thanks for the info, should I ever screw something up its nice to know there are people out there who can clean up my mess!
spacemoose1 said:
a company called Mobile Tech is offering an "unbricking" service on all versions of the Galaxy Tab.
Click to expand...
Click to collapse
Hi spacemoose1
Thanks for link and as always, thanks for honeycomb port. I would like to ascertain the definition of BRICK? with your help, if I may.
(disclaimer: pls forgive my wrong terms or exagerated explanation, but most importantly, pls correct me if I'm wrong)
BRICKed = software total lost, must use JTAG to force revive it, Samsung has it, or buy from web supplier around 300 USD ??? 500 USD ???
JTAG is a device to push software into all newly borned IC. I.E. when factory make IC, it's empty software inside, hence has a special device to push voltage into all sections of the IC, then force the code in.
Another term is ???CRASH??? or ???HANG???, (I don't know) anyway is not BRICKed, hence a reflash can recover it.
Samsung uses proprietary method a lot, not follow conventional, make usb driver very complex. USB driver install EXE around 15MB to 28MB depends on version, ALL work the same.
but, when the device = sgt7 in different state/condition, the driver must RE-ESTABLISH again, or else cannot work.
I.E.
state 1 = "OPERATIONAL"device in android operation, normal use, surf web, phone call etc
state 2 = "SLEEP" device powered off, show battery big icon charging when powered by charger
state 3 = RECOVERY mode
state 4 = DOWNLOAD mode - this is one of the way to FORCE flash to recover, as long as bootloader and something still intact
state 5 = PHONE-!-PC mode
stage 6 = "COMA" device powered off, NO show of battery big icon, even when charger supplied. Don't panic, let it charge fully 4 hours from 2 amperes supply, 10 hours from PC 500mA. It will start again !!!. Battery big icon will appear around 30% battery charged, I know because that's what I saw. I didn't check when it's in 10% or 20%. The 1st time I check was already 30% up from no-boot or no respone.
User need to plug device into PC during each of the state above at least once, in order for various flashing functions to work.
i.e. when it's a newly arrived device, usually install the usb driver 1st, with device state in android OS running properly, then plug in to USB and see "new device detected" installing, pls wait. Finished.
But when flashing via Odin using state 4 = DOWNLOAD mode, user may experience no connection, no COM3 or something. Because device must be unplugged in USB, power-up in state 4 = DOWNLOAD mode, plug in USB, "new device detected" installing = RE-ESTABLISH, done. UNPLUG USB, replug in usb, then COM3 appears FLASH will be succesfull.
same goes for other state.
p.s. many users reported BRICKed but then recovered WITHOUT JTAG is misleading beginners, hence should rename the term to ???CRASH??? or ???HANG???. although some previously use "SEMI-brick", which is acceptable.
stage 3 = ClockWorkMod flashing (super convenient, especially on the move without PC)
stage 4 = Odin / Heimdall both works (still convenient and easy )
stage 5 = Odin / Heimdall both works (still convenient and easy )
???CRASH??? or ???HANG??? or "SEMI-brick" is usually SUCCESFULLY recovered via restock+PIT
(final disclaimer, incase above is correct and help and is copied, pls correct whatever mistakes found, feel free.)
*** Thanks for all those who taught me my mistakes *** devs and fellow forumers
ManticoreX said:
This is cool, but I would recommend trying to go through Samsung first if you are still under warranty. I screwed up my primary bootloader and contacted them. They took care of shipping costs, fixed it up, and sent it back in about a week and a half. If Samsung hadn't fixed it I would defiantly have payed the $50 here though.
Click to expand...
Click to collapse
Yeah, warranty repair is always a better choice. But sometimes you've already voided the warranty, lol.
I guess, if u change factory installed rom/kernel warranty gonna be history
thanx for the post ... it might gonna be the last resort...
cx5 said:
Hi spacemoose1
Thanks for link and as always, thanks for honeycomb port. I would like to ascertain the definition of BRICK? with your help, if I may.
(disclaimer: pls forgive my wrong terms or exagerated explanation, but most importantly, pls correct me if I'm wrong)
BRICKed = software total lost, must use JTAG to force revive it, Samsung has it, or buy from web supplier around 300 USD ??? 500 USD ???
JTAG is a device to push software into all newly borned IC. I.E. when factory make IC, it's empty software inside, hence has a special device to push voltage into all sections of the IC, then force the code in.
Another term is ???CRASH??? or ???HANG???, (I don't know) anyway is not BRICKed, hence a reflash can recover it.
Samsung uses proprietary method a lot, not follow conventional, make usb driver very complex. USB driver install EXE around 15MB to 28MB depends on version, ALL work the same.
but, when the device = sgt7 in different state/condition, the driver must RE-ESTABLISH again, or else cannot work.
I.E.
state 1 = "OPERATIONAL"device in android operation, normal use, surf web, phone call etc
state 2 = "SLEEP" device powered off, show battery big icon charging when powered by charger
state 3 = RECOVERY mode
state 4 = DOWNLOAD mode - this is one of the way to FORCE flash to recover, as long as bootloader and something still intact
state 5 = PHONE-!-PC mode
stage 6 = "COMA" device powered off, NO show of battery big icon, even when charger supplied. Don't panic, let it charge fully 4 hours from 2 amperes supply, 10 hours from PC 500mA. It will start again !!!. Battery big icon will appear around 30% battery charged, I know because that's what I saw. I didn't check when it's in 10% or 20%. The 1st time I check was already 30% up from no-boot or no respone.
User need to plug device into PC during each of the state above at least once, in order for various flashing functions to work.
i.e. when it's a newly arrived device, usually install the usb driver 1st, with device state in android OS running properly, then plug in to USB and see "new device detected" installing, pls wait. Finished.
But when flashing via Odin using state 4 = DOWNLOAD mode, user may experience no connection, no COM3 or something. Because device must be unplugged in USB, power-up in state 4 = DOWNLOAD mode, plug in USB, "new device detected" installing = RE-ESTABLISH, done. UNPLUG USB, replug in usb, then COM3 appears FLASH will be succesfull.
same goes for other state.
p.s. many users reported BRICKed but then recovered WITHOUT JTAG is misleading beginners, hence should rename the term to ???CRASH??? or ???HANG???. although some previously use "SEMI-brick", which is acceptable.
stage 3 = ClockWorkMod flashing (super convenient, especially on the move without PC)
stage 4 = Odin / Heimdall both works (still convenient and easy )
stage 5 = Odin / Heimdall both works (still convenient and easy )
???CRASH??? or ???HANG??? or "SEMI-brick" is usually SUCCESFULLY recovered via restock+PIT
(final disclaimer, incase above is correct and help and is copied, pls correct whatever mistakes found, feel free.)
*** Thanks for all those who taught me my mistakes *** devs and fellow forumers
Click to expand...
Click to collapse
I pretty much agree, but I might refine:
BRICK= Unit does not power up, visibly charge, reach a boot-screen of any kind including a service or "download" screen. A device in this state requires service from the manufacturer or an individual equipped with the proper tools. There is no other way to recover a device in this state.
SOFT-BRICK= Unit powers up, reaches a "download" or service screen, visibly charges but does not boot into an OS. Crashing, hanging etc. all apply here. It is easy to recover a device from this state so long as one has access to a firmware that was designed for the device and the ability to flash said firmware.
SEMI-BRICK= See soft-brick above
JTAG= Provides access to system hardware by applying the correct voltage to the correct pins in order to push software via an external program.
In regards to the usb drivers, there are only actually 4 states
1. Active userspace
2. Serial gadget mode
3. Recovery
4. USB storage mode
And there is a separate driver for each of these (except recovery) in the Samsung driver package that should install automatically when the device is plugged in during normal use on a stock rom, or with the installation package available on the web.
The rest of it you've got pretty much correct.
Money seems right, but the amount of work that guy has to go thru is amazing, so much to tare it apart, and reassemble. Then again when it is put back toether, he checks it, what if it did not take the fix... all over again.
Hardbricked Tab Save by Mobile Tech
I hardbricked my galaxy tab bought in Cambodia. My little brother open the tab trying to take the battery off and put it back on, thus void the warranty, found him on the Samsung vibrant forum, sent the tab to him got it back good as new. This person is professional, honest and good communication with his customers, you'll be happy with his work, if he can't fix it you get your money back (minus shipping and diagnosis)...Glad he is arround to help...
spacemoose1 said:
I pretty much agree, but I might refine:
BRICK= Unit does not power up, visibly charge, reach a boot-screen of any kind including a service or "download" screen. A device in this state requires service from the manufacturer or an individual equipped with the proper tools. There is no other way to recover a device in this state.
SOFT-BRICK= Unit powers up, reaches a "download" or service screen, visibly charges but does not boot into an OS. Crashing, hanging etc. all apply here. It is easy to recover a device from this state so long as one has access to a firmware that was designed for the device and the ability to flash said firmware.
SEMI-BRICK= See soft-brick above
JTAG= Provides access to system hardware by applying the correct voltage to the correct pins in order to push software via an external program.
In regards to the usb drivers, there are only actually 4 states
1. Active userspace
2. Serial gadget mode
3. Recovery
4. USB storage mode
And there is a separate driver for each of these (except recovery) in the Samsung driver package that should install automatically when the device is plugged in during normal use on a stock rom, or with the installation package available on the web.
The rest of it you've got pretty much correct.
Click to expand...
Click to collapse
You should post this in Q/A thread on its own as its very helpful and maybe it will stop the 1% of people saying help my phone is bricked comments ... the other 99% don't read anyway otherwise they would discover their phone isn't bricked and if they read properly it would not have gotten to the state in the first place .. and no I never posted something like that myself >:¬}
but well done on this..
alexgogan said:
You should post this in Q/A thread on its own as its very helpful and maybe it will stop the 1% of people saying help my phone is bricked comments ... the other 99% don't read anyway otherwise they would discover their phone isn't bricked and if they read properly it would not have gotten to the state in the first place .. and no I never posted something like that myself >:¬}
but well done on this..
Click to expand...
Click to collapse
+1
Sent from my GT-P1000 using Tapatalk
Nice find. For that amount of effort disassembling, and reviving, $50 is a very realistic price. I'll keep these guys in mind if I run into issues with my tab.
$50 for that much work is an absolute bargain! I wish I didn't live in a country where you get charged $200/hr for someone to pick their nose.
It's actually not that much more difficult than popping an OS install CD into a hosed computer and pressing 3 keys to let it run through the installation after flashing a corrupt motherboard BIOS. Yes, it takes familiarity with the software and hardware, but it's by no means a feat that requires a special skillset.
Granted, few people have JTAG stuff handy, so $50 is definitely worth it if you've hosed your device, but don't make it sound like he's sweating and coding the bootloader by hand, strenuously manipulating micro tools to disassemble the tablet and flipping DIP switches to restore the bootloader. You spend 5 minutes taking apart the tablet, you attach the JTAG cable, run the supplied software on your computer, and sit there recording the screen with your video recorder while the progressbar moves from 0 to 100.
Again, it's worth $50 simply because not everyone and their mother has JTAG hardware sitting around, but by no means is it hard. It's the same reason I can get away with charging $100 to clean viruses off of a computer. People either don't have the tools or don't know how to use them. That being said, I don't know a damn thing about using JTAG to restore a corrupt bootloader, nor do I have the right hardware, so I'd pay $50 if I were ever in the situation.
Edit: And yes, $100 for a virus clean is a lot, but people generally change their mind when I explain to them why they got viruses, as well as installing proper antivirus software and then instructing them on how to avoid infection in the future. I rarely get repeat business from the same customer but I get A LOT of referrals ;p They're happy paying that much when the person educates them instead of cleaning, not installing/explaining, then having to bring the computer in again two weeks later for another wallet-gouge, which most other computer 'repair people' gladly do over and over.
Everything in this world is rinse and repeat... The money comes from time spent learning to use the hardware properly, micro soldering skills (which isn't easy, no matter who you are), confidence enough to offer it as a service, not to mention the couple hundred bucks for the jtag software and hardware.
Now, the fact that if you have your device in a bricked state you likely voided the warranty, it's a 600 dollar brick if your samsung tech recognized it... 50 bucks is a steal to not deal with samsung anyway.
Try to be less pompous next time oh savoir of the hundred bone virus... Your poop stinks too, promise.
Sent from my "better than an iPad" tab running Overcome Hermes.
LycaonX said:
It's actually not that much more difficult than popping an OS install CD into a hosed computer and pressing 3 keys to let it run through the installation after flashing a corrupt motherboard BIOS. Yes, it takes familiarity with the software and hardware, but it's by no means a feat that requires a special skillset.
Granted, few people have JTAG stuff handy, so $50 is definitely worth it if you've hosed your device, but don't make it sound like he's sweating and coding the bootloader by hand, strenuously manipulating micro tools to disassemble the tablet and flipping DIP switches to restore the bootloader. You spend 5 minutes taking apart the tablet, you attach the JTAG cable, run the supplied software on your computer, and sit there recording the screen with your video recorder while the progressbar moves from 0 to 100.
Again, it's worth $50 simply because not everyone and their mother has JTAG hardware sitting around, but by no means is it hard. It's the same reason I can get away with charging $100 to clean viruses off of a computer. People either don't have the tools or don't know how to use them. That being said, I don't know a damn thing about using JTAG to restore a corrupt bootloader, nor do I have the right hardware, so I'd pay $50 if I were ever in the situation.
Edit: And yes, $100 for a virus clean is a lot, but people generally change their mind when I explain to them why they got viruses, as well as installing proper antivirus software and then instructing them on how to avoid infection in the future. I rarely get repeat business from the same customer but I get A LOT of referrals ;p They're happy paying that much when the person educates them instead of cleaning, not installing/explaining, then having to bring the computer in again two weeks later for another wallet-gouge, which most other computer 'repair people' gladly do over and over.
Click to expand...
Click to collapse
I've got to call you out on this one. Mis-connecting or shorting any wires will lead to a damaged PCB and an un-resurrectable TAB. I'm also a Systems Admin for a living so I understand where you are coming from. You must realize that I solder at levels of .1mm in spacing on the Captivate, Vibrant and Nexus S. Electrical engineers and technicians have first hand talked with me about the difficulty of doing this and is NOT something that anyone can do. You'd think twice when you burn up a phone or two valued at $500 a pop trying to JTAG them. There is more skill involved than you would think. Not to mention the liability when dis-assembling the device. JTAG software is decent but it's not fully automated. There are TCK frequencies, RTCK frequencies different PBL partition sizes, full dcc loader read/writes and the requirement of EXACT voltage from an external power supply that are needed in MANY cases. Plus, there is little to no support when fixing a device. This means that if you can't figure it out, nobody else is going to for you. I'm not trying to brag but yet point out that this isn't like plugging in your phone for an ODIN flash. I've taken hundreds of hours of time and 1000's of dollars to create what I feel is the most trusted JTAG authority online ANYWHERE. I greatly appreciate having the opportunity to help the community and enthusiasts in this community. If this was as easy as you are claiming, you could get JTAG hardware and a manual at Best Buy. I have to say you put it best when you said you don't know anything about JTAG... Ok end of rant I was just a bit bothered by your post.
Ok with that being said, thanks for the personal testimonies and compliments. I will be here whenever anyone needs JTAG assistance in the future or around the forums to help answer Q&A when it doesn't require JTAG. Here is a Nexus S promo to realize how tiny some of these things are
http://www.youtube.com/watch?v=Ecp8jKmm48k
i would love to learn more on how to do stuff like this if i had moneyz. the .1mm ext.
not just for android but to make my own ish.
thanks for the awsome videos.
Thanks for the link, hope I won't need it ;-)
Sent from my GT-P1000 using XDA App
I hope someone can help explain my S4's odd behavior. I'll try to be brief but give enough details for the experts to get an idea.
- The phone discharges to about 30% and then either turns off or starts to bootloop or just behaves weirdly by closing processes and apps making it unusable
- Once fully charged, it'll finally boot again almost normally but first I have to go into recovery and wipe partition and after various attempts it'll finally boot. Its behavior will be normal and everything will function perfectly well until it goes back down to about 30% charge again
- There are 2 things to rule-out: battery and rom. The battery is brand new and 100% original because I've already changed it thinking that it was the culprit. I'm currently using AOSP 4.4 rom but the behavior is the same with any rom even stock roms
- I can't get it serviced because thanks to the new bootloader my warranty is void
Any suggestions?
USB board/port. Replace it first. Given it's quick/cheap/easy to do on the S2, I think you'll find it's the same on the S4. Search online & here for details/the service manuals which might be useful. You could also pay a local mobile repair shop to do it, but why pay them 3-5x (or more) what the part costs in labour to do it when you can do it yourself ?
Thanks! Will try that and will def do it myself:good:. Am pretty familiar with hardware. I too think at this stage that it's a hardware issue
MistahBungle said:
USB board/port. Replace it first. Given it's quick/cheap/easy to do on the S2, I think you'll find it's the same on the S4. Search online & here for details/the service manuals which might be useful. You could also pay a local mobile repair shop to do it, but why pay them 3-5x (or more) what the part costs in labour to do it when you can do it yourself ?
Click to expand...
Click to collapse
Just out of curiosity, why do you think it's the usb port? I have to say that it crossed my mind once as well because on a few rare occasions I had problems charging my phone as if the usb cable or port was defective. My PC at times has also had problems recognizing my galaxy when plugged in, but only very rarely so I didn't make much of it
The charging issues you've had, another battery not solving those issues, and the auto shutdowns/auto bootloops for no reason have always been symptomatic of the USB board/port on the fritz on the S2 and the S3 (saw so many of these in S2 Q&A this year particularly), just sounds a lot like it. Put it this way, if it's not, it's something much worse hardware-wise, but I think you'll find the easy fix will resolve it in this case.
Hi guys!
So while using my phone halfway, it suddenly powered off and died. At first I thought it was something small and tried to power it on again, but unfortunately it seems to be a much bigger problem. I am unable to do anything with the phone at all. It's become a literal brick.
I have not done any rooting nor have I dropped the phone into the water. I dropped my phone a couple of times, but it was with a proper phone cover.
When I tried to charge my phone, the charging light did not come on. I have tried the battery in an external charging kit and it works fine, therefore I do not believe that it is a battery problem.
The lucky thing is that my phone is still under warranty. However, I was told that the SOP for servicing the phone is to remove all personal data during the recovery process.
Unfortunately, I didn't back up the files in my phone because I didn't see any signs that the phone was gonna die on me, so I was wondering if there was any other way to save my data.
I read online that it may be worth trying to use a USB jig to try to force the phone into download mode. Is this possible? Does anyone know where I may be able to purchase one?
Unfortunately, I do not know which specific model my carrier sells, but it's a Qualcomm 2.7 KHz 4G+ note 4. Can't remember the exact firmware it was running on, but it should be the latest stock firmware.
Would greatly appreciate any advice. Thanks!
Is there anyone here who has any advice for me?
royaloyalz said:
Is there anyone here who has any advice for me?
Click to expand...
Click to collapse
jig is basically a 300K ohm resistor across pins 4 and 5, so searching for brand names/judging by marketing descriptions won't help. It can only fix soft bricks for you, specifically it lets you enter download mode where you can use odin to flash stuff you want. It wont help you in any other way.
Now that we are clear, the cheapest ones I could find are these:
http://www.amazon.com/SainSonic-Dongle-Samsung-Captivate-Vibrant/dp/B0053H73JQ
http://www.amazon.com/Download-adapter-Samsung-Galaxy-Unbrick/dp/B008THL0V4
Buy whichever you like
And if its a hard brick, off to the service center you go!
PS: i have no idea about any way to backup from download mode, maybe someone else can help you on that part.
If you are able to dirty flash a rom and get it booting then you can backup all you want. Hope that works for you.
Thanks for the advice!
Unfortunately because I wasn't able to power up the device I had to send it into the service center. They replaced the motherboard and the charging point for me and I got back my phone 4 hours later.
Lesson learnt, always backup your data every day.
so, this phone died for me in 2017, and have been in a drawer since then. then i thought why not ask. so long story short if i remember correctly: bought it new. i rooted it since all the cool kids do that. then i did some update i think. and then in the winter of 2017 in beginning it just started behaving weirdly for me and then it turned off and all kinds of shenanigans. cant restart using different methods, sometimes it blinks, sometimes that bios menu comes up. blabla. so i tried to send it to the local repairshop that the seller used. but since i had it rooted they refused to fix it. so now i have a phone that costed 600 euro + 70 euro in service cost and it doesnt work. and then its been in a drawer since then.
i took it out, had it and the battery in a freezer for a while like some has said on internet didnt work.
anyway. does anyone here know any tips? if i want to flash the room can that be possible? or is this a lost cause? was this a common problem with note 4? i loved it and it crushed my heart when it stopped working. i still have a few months of pics etc on it from back then that ive never been able to get out. i attached it to the computer now and the computer makes a sound but nothing more.
any tips?
darknessviking said:
so, this phone died for me in 2017, and have been in a drawer since then. then i thought why not ask. so long story short if i remember correctly: bought it new. i rooted it since all the cool kids do that. then i did some update i think. and then in the winter of 2017 in beginning it just started behaving weirdly for me and then it turned off and all kinds of shenanigans. cant restart using different methods, sometimes it blinks, sometimes that bios menu comes up. blabla. so i tried to send it to the local repairshop that the seller used. but since i had it rooted they refused to fix it. so now i have a phone that costed 600 euro + 70 euro in service cost and it doesnt work. and then its been in a drawer since then.
i took it out, had it and the battery in a freezer for a while like some has said on internet didnt work.
anyway. does anyone here know any tips? if i want to flash the room can that be possible? or is this a lost cause? was this a common problem with note 4? i loved it and it crushed my heart when it stopped working. i still have a few months of pics etc on it from back then that ive never been able to get out. i attached it to the computer now and the computer makes a sound but nothing more.
any tips?
Click to expand...
Click to collapse
Sounds to me like either dead emmc or misconnection.
If it's just? misconnection there are tips (increasing the pressure by cardboard).
Can you access download mode?
Sometimes it shows there "dead emmc".
I somewhere read about a testing app.
Gotta search.
Where in Europe are you?
In the German Android-hilfe forum there is a member who fixes that.
Either exchanging the emmc or resoldering it.
If the chip is dead probably the data are lost.
afaik flashing the stock ROM deletes data.
It's a known problem, yes.
bmwdroid said:
Sounds to me like either dead emmc or misconnection.
If it's just? misconnection there are tips (increasing the pressure by cardboard).
Can you access download mode?
Sometimes it shows there "dead emmc".
I somewhere read about a testing app.
Gotta search.
Where in Europe are you?
In the German Android-hilfe forum there is a member who fixes that.
Either exchanging the emmc or resoldering it.
If the chip is dead probably the data are lost.
afaik flashing the stock ROM deletes data.
It's a known problem, yes.
Click to expand...
Click to collapse
Excellent feedback and assessment @bmwdroid . Thank you for sharing.
I only wish to add that there is a way to flash Samsung firmware while keeping user data. Of course, this method wouldn't be effective when it comes to emmc hardware failure so Im posting it for general information purposes only.
If you have downloaded the firmware for your Samsung Galaxy device you’ll find 2 CSC binaries with *.tar.md5*extension (namely CSC and Home_CSC ) inside along with BL, AP, and CP.*CSC*and*HOME_CSC*are necessary for different purposes, and you have to choose one or the other depending on your goal.
CSC –*If you flash the CSC file, it’ll perform a*factory reset*of your Galaxy device and wipe all data while installing a new firmware to bring your device to the same*state as it was when you purchased it. Go with CSC if you want a*clean installation.
HOME_CSC*–* On the other hand, if you want to*keep your Samsung phone’s data and settings*even flashing the stock firmware, you can select the HOME_CSC file.