Related
Guys,
im in extremely deep **** now.I accidentally tried flashing a stock ROM via SD card and now ive gt a ROM code error and 00028002 'Not Allow" error.What makes this worse is that my Vista computer is not recognizing any USB connection when i connect my HD2 to the computer.If i need to flash a stock rom via RUU wrapper to get through this stupid ROM code error, i need a USB connection on the first place...which IS NOT WORKING NOW!!!...im using a 512MBLeo,which is now stuck at SPL-1.42(previously HSPL)...im sitting duck here guys...i really really need your help on this one.i cant boot normally into 6.5,i cant flash a new ROM,i cant use bootloader and flash a LEOIMG using SD card cus it returns the above errors and i cant use my PHONE!!!...im extremely frustrated and helpless.please help guys...thanks alot...
If I understand you can still get to bootloader correct?
Exactly what official ROM did you try to flash?
Where did you get the ROM from?
Just so you know you can still flash HSPL with the 1.42.0000 SPL you have.
ROM code error usually means that official ROM is not for that HD2.
I flashed '1.48.405.2' which i downloaded from the net(http://theunlockr.com/2010/04/22/how-to-get-the-htc-hd2-back-to-stock/)...I tried flashing LEOIMG(SD card method) from Elegancia GTX v5.0 ROM,but thats returning the same error plus...it gets stuck on the white 'loading screen'.I know i can flash HSPL or any other stock rom with my current SPL,but my USB connection is not working...thats exactly the problem now...any idea where to get the actual stock ROM for my HD2?...Maybe that might prevail...Thanks.
kawshigan said:
I flashed '1.48.405.2' which i downloaded from the net...I tried flashing LEOIMG(SD card method) from Elegancia GTX v5.0 ROM,but thats returning the same error.I know i can flash HSPL or any other stock rom with my current SPL,but my USB connection is not working...thats exactly the problem now...any idea where to get the actual stock ROM for my HD2?...Maybe that might prevail...Thanks.
Click to expand...
Click to collapse
Yes go to htc.com amd enter the serial number of your HD2 (can be found under the battery) and it will only let you download the ROMs that are for your HD2. Also make sure the HTC site you go to is for your part of the world, It has links on the site to go to HTC sites for other countries.
As for your no USB go to your device manager in control panel and find your HD2 ther while it is connected via USB it will be listed as unknown, mobile device, or something like that but it will be there. Just click on it once to get it to drop down to the actual device and then right click it and select update drivers and then select from internet. If this does not work download the latest version of Windows Mobile Device Center (WMDC) and install it to your computer and this should give you the drivers you need.
Alright ill try all that and get back to you.Thanks alot for your advice!
Error Resolved
First,i would like to say thanks to you, T-Macgnolia.The ROM downloaded from the HTC website, which i flashed via sd card worked like a dream...However, the same cant be said for my USB connection though(I tried everything you said).My computer still keeps dropping USB connections intermittently...i miraculously managed to flash HSPL 3 on my HD2 just before the USB connection dropped.I was running WM 6.5 and android previously and i want to dual boot wp7 and android...which needs a USB connection(for MAGLDR and WP7)...Charging works fine via AC charger and via USB port(its just USB connection itself...any ideas where the fault lies?).i personally think the problem lies with my USB cable(as other devices work fine with the USB ports in my laptop). Guess i just have to buy a new micro usb cable(...thanks for your advice again.
kawshigan said:
First,i would like to say thanks to you, T-Macgnolia.The ROM downloaded from the HTC website, which i flashed via sd card worked like a dream...However, the same cant be said for my USB connection though(I tried everything you said).My computer still keeps dropping USB connections intermittently...i miraculously managed to flash HSPL 3 on my HD2 just before the USB connection dropped.I was running WM 6.5 and android previously and i want to dual boot wp7 and android...which needs a USB connection(for MAGLDR and WP7)...Charging works fine via AC charger and via USB port(its just USB connection itself...any ideas where the fault lies?).i personally think the problem lies with my USB cable(as other devices work fine with the USB ports in my laptop). Guess i just have to buy a new micro usb cable(...thanks for your advice again.
Click to expand...
Click to collapse
Yeah buy a new cable and see if that helps. If the problem pursists then you probably have a problem with the pins in your micro USB port of your HD2 that are randomly loosing connection to the main board because the solder points for the USB port is become cracked, loose, or just seperating for some reason. You might can find a cell phone repair shop that can resolder the connections for you are just Chang the intierior main board out for you ifcthis is the problem.
Hello,
here is the situation.
i have a hd2 with magldr 1.13
android in nand
android in sd
both are working fine.
im trying to flash wp7 but my pc wont even pick up the connection (device not listed in devmgmt) however the phone is charging no problem.
i have installed, uninstalled and re-installed:
android sdk tools
windows mobile device center
windows phone sdk
i have manually removed each drivers after uninstalling all these through devmgmt.msc
i have also tried all this on 2 other PCs, with the same results so far.
i will try on a 4th PC later tonight.
i havent had the opportunity to try another cable yet.
what is causing this?
Thanks,
In wmdc did you untick "allow USB connections"?
That doesn't make any sense. If you flashed Android to NAND it should Flash WP7 to NAND with the same ease.
Make sure you hate .net 4.0 installed too, I know that helped me.
on the phone do you have it set to charge only from USB?
menu button - settings - Connect to pc - Default connection type
yep "allow USB" is unticked
i have .NET 4.0 installed...
i dont even have that in android:
"menu button - settings - Connect to pc - Default connection type"
do i have a faulty phone? the last time i flashed was about 2.5 weeks ago
willrider said:
yep "allow USB" is unticked
i have .NET 4.0 installed...
i dont even have that in android:
"menu button - settings - Connect to pc - Default connection type"
do i have a faulty phone? the last time i flashed was about 2.5 weeks ago
Click to expand...
Click to collapse
I don't understand what the problem is exactly:
You connect your HD2 to your PC, load up MAGLDR and select usb flash mode.
then you're running the DAF WP7 flasher and then it fails to connect or what?
orangekid said:
I don't understand what the problem is exactly:
You connect your HD2 to your PC, load up MAGLDR and select usb flash mode.
then you're running the DAF WP7 flasher and then it fails to connect or what?
Click to expand...
Click to collapse
on the phone, nothing happens.
on pc flasher fails after a while.
also on the tri-colour HSLP boot, i can see "serial"
but i cant seem to put in "USB" mode.
i tried booting into HSPL with the USB connected but then it wont display "serial" or "USB"... it stays blank
willrider said:
on the phone, nothing happens.
on pc flasher fails after a while.
also on the tri-colour HSLP boot, i can see "serial"
but i cant seem to put in "USB" mode.
i tried booting into HSPL with the USB connected but then it wont display "serial" or "USB"... it stays blank
Click to expand...
Click to collapse
oh well if bootloader stays on serial its almost certainly hardware, cos it should switch to USB regardless of whether flashing works and drivers and what not. You say you can charge so I would suspect a broken data pin inthe socket,perhaps dirty, perhaps bad solder, perhaps faulty cable.
samsamuel said:
oh well if bootloader stays on serial its almost certainly hardware, cos it should switch to USB regardless of whether flashing works and drivers and what not. You say you can charge so I would suspect a broken data pin inthe socket,perhaps dirty, perhaps bad solder, perhaps faulty cable.
Click to expand...
Click to collapse
He's saying it doesn't say serial or USB, so it might be some software issue, "it stays blank"
I would flash stock via SD, then flash HSPL, task29, then flash magldr, then try again.
yea, but since it does say serial when usb isn't connected, means it is detecting something, because it can tell the difference. You may be right in a corrupted bootloader, but id bet its more likely hardware, shorted data pins, or a break on either the phone or the cable. (all just guesswork, of course, , , hurry up and find out, OP! minds with nothing better to do need to know! hehe)
orangekid said:
I would flash stock via SD, then flash HSPL, task29, then flash magldr, then try again.
Click to expand...
Click to collapse
@OP
+1 on that, but of course it will all stop at "stock via SD" if that doesnt fix it,because hspl gone, no usb to reapply it, no radio flashing, so no more android, just stock winmo roms,, so think carefully what you want, if you can live with what you have, id be tempted to leave it alone until you need to.
samsamuel said:
yea, but since it does say serial when usb isn't connected, means it is detecting something, because it can tell the difference. You may be right in a corrupted bootloader, but id bet its more likely hardware, shorted data pins, or a break on either the phone or the cable. (all just guesswork, of course, , , hurry up and find out, OP! minds with nothing better to do need to know! hehe)
@OP
+1 on that, but of course it will all stop at "stock via SD" if that doesnt fix it,because hspl gone, no usb to reapply it, no radio flashing, so no more android, so think carefullyu what you want.
Click to expand...
Click to collapse
That's true, if you flash stock via sd then you're back to SPL 3.03, but reflashing HSPL might be what you need to do, so it's hit or miss.
If it's hardware then you will find out this way and since you'll hopefully be back to stock SPL you could do warranty on it.
I hate to say it but that's most likely a dead physical USB port. I work on the HD2's daily and have seen this problem several times and it was 100% not software related which I have verified after a fully memory sweep and write of a JTAG dump from a working phone to the defective one. In these case the phone would also charge but had no PC connectivity either. You can however flash all the WinMO ROM's you would like over the SD-Card and definitely still benefit from the SD-Card style of booting Android ROM's so the phone is not a total wash. You can also still hope that Cotulla or some DEV will come up with a way to flash CWM Recovery from the SD-Card to the NAND. Then you could even still have NAND based Android ROM's as the CWM step is the only part of MAGLDR to Android that involves PC > Phone flashing.
The port is cheap at about $6.00 USD but the skill required to put one on is high. I don't offer it as a service yet but I'm planning on it soon as I solder frequently on JTAG ports smaller than the usb ports themselves and have the skill to do this.
EDIT: I'm also not 100% sure it's the port to blame but most likely it is. However, it could still be something inline with the USB data bus on the phone to blame.
connexion2005 said:
I hate to say it but that's most likely a dead physical USB port. I work on the HD2's daily and have seen this problem several times and it was 100% not software related which I have verified after a fully memory sweep and write of a JTAG dump from a working phone to the defective one. In these case the phone would also charge but had no PC connectivity either. You can however flash all the WinMO ROM's you would like over the SD-Card and definitely still benefit from the SD-Card style of booting Android ROM's so the phone is not a total wash. You can also still hope that Cotulla or some DEV will come up with a way to flash CWM Recovery from the SD-Card to the NAND. Then you could even still have NAND based Android ROM's as the CWM step is the only part of MAGLDR to Android that involves PC > Phone flashing.
The port is cheap at about $6.00 USD but the skill required to put one on is high. I don't offer it as a service yet but I'm planning on it soon as I solder frequently on JTAG ports smaller than the usb ports themselves and have the skill to do this.
EDIT: I'm also not 100% sure it's the port to blame but most likely it is. However, it could still be something inline with the USB data bus on the phone to blame.
Click to expand...
Click to collapse
If this is the case I wouldn't flash stock via SD since you have no way to flash HSPL after that.
Just bought a used HD2 (TMOUS). I checked the bootloader and it already had HSPL installed. However, I wanted to flash stock ROM and do task29 prior to installing HSPL again myself.
I flashed the stock ROM v3.14.531.1 via microSD card method. Then I tried to run task29 and it failed. Bootloader wouldn't detected the USB connection. I also try to install HSPL but it doesn't work. I get an error: USB COnnect Failed!
When I connect to PC or wall charger, the phone charges perfectly fine. I even see the icon that says its connected.
When I am on the bootloader and connect the phone to my PC via USB, the white background area says "Serial" and it doesn't change to "USB".
I tried using different USB cables and also different PC, but still no luck.
What is wrong? Why can't I connect via USB? Help please.
Have you tried droidexployer? Doubt that'll work but worth a shot. What might be wrong is you don't have the proper drivers installed.
Sent from my Desire HD-2 using XDA App
htccraze said:
Have you tried droidexployer? Doubt that'll work but worth a shot. What might be wrong is you don't have the proper drivers installed.
Sent from my Desire HD-2 using XDA App
Click to expand...
Click to collapse
Droidexployer is for devices running rooted android. mine is still stuck on windows, i can't install hspl in order to run android...
i am sure its not a driver problem because i have another hd2 which connects perfectly fine.
Have you tried it on a different usb port on the pc? Sometimes one will work while another won't for some reason. Also remember to check the options in ActiveSync or WMDC to ensure usb connections are allowed, seems a stupid mistake, but one I have made myself before. If all that fails, maybe try on a different pc or with a different usb cable. Sorry for the super simple answers, I see you're not a brand new user, but its often these simple little things that hang us up
Change the battery
Change the battery ?
I seen your comment that said you already had hspl so I just assumed it was on android, sorry. Yea the different usb ports is a great idea if it wasn't for the fact that you even tried it on a different computer as well. Since you said you bought it used would you mind saying where from? I've known people who have problems with they're phone & can't find out how to fix it so they try and sell it on ebay. If you did get it from there the best thing to do is contact the seller and explain your problem. Ask if it had this problem before and say you don't want this phone if it's not repairable. With ebay you only have a short time to file a complaint if it leads to that.
Sent from my Desire HD using XDA App
another "simple" thing..
check for dirt or fluff in usb port
same here but I have EU version of HTC HD2...
also i Have MIUI 1.8.5. Gibgerbread 2.3.5 and same thing with bootloader...when start phone everything works fine !!!
If you find any solutions please write it to me so i can solve problem! Thanks
Are you able to charge the phone? if not, it's possible the microusb port is broken.
yes able to charge phone....i think its manufacture something cause tryed to connect to other PC with other USB and still same prob.
sportman123 said:
yes able to charge phone....i think its manufacture something cause tryed to connect to other PC with other USB and still same prob.
Click to expand...
Click to collapse
Have you installed windows mobile device center?
I am having the same issue. It worked a couple weeks ago. Now I can not get USB connection in MAGLDR or Bootloader...
Any help?
Yeah, me too.
Get your self a new sparkly xoom and wanna put android on my hd2. Oh well no mobile internet for my xoom. Unless any one knows of any wm6.5 app/prog that'll do it?
Arty U.K.
I want to ask if there is possibility to install CLK and CWM on phone with WM 6.5 without USB because my friend´s HD2 can only be charged via USB beacause of broken USB port and MB......If there is any possibility like SD install please help me.
Thank you
This is not possible. Did you install drivers for the phone on the pc? Also some micro usb cables do not allow a data connection. If it is still charging over usb these two points could be possible issues that cause your problem.
Sent from my HTC HD2
They said to him that they fixed the USB port to charge but its impossible now to connect it to USB-PC
It's better to fix the usb problem and then to install androind on your phone
I have CMYLXGO's Topia HD-NAND Edition on my hd2.
The problem that I am having is that Mobile device Center does not show my phone when I connected to the usb.
can anyone help me?
Thanking you in advance,
Henry
Isn't mobile device center for windows mobile only?
You're on Android, why do you want to connect ti WMDC anyway?
Yeah, you don't have a WMo phone anymore, so to say.
If you want to connect to the PC, try USB mass storage.
If you need any help, just let me know.
Ok, so how can I change differents roms if my phone does not sync. with my pc, I used to able to do it, now for some reason I can't.
thank you for yor reply,
Henry
It depends on what room are you using?
If you are using magldr, clk or you are just flashing through clockworkmod.
For every type of bootloader there is a way to enter the flashing menu.
Just tell me what rom (and what type of bootloader) are you using and I'll tell you what to do.
-----------------------------------
HTC HD2
ACA GB 237 CM7
kernel 2.6.32.15
NAND Android ROCKS!
As a relative noob myself I recommend either HD2 tools or easyandroid, the latter being easy to use and explains every step of the process as you go and confirms you have correct radio, magldr HPSL ect already installed.
If you are looking for a good ROM, Team Blue Droid have produced an excellent sense 3.5 Rom which looks the business and works far better than many others I have flashed recently on mh EU HD2. I am not that technically minded regarding SD card partition types, but I run mine via SD card after flasing a 1024 partition using CMR and the accompanying DAF.exe.
From reading many threads I understand camcorder is less than perfect on most roms at highest res.
link is below
http://forum.xda-developers.com/show....php?t=1275119
Try it with "HTC Sync" (download 4free) instead of mobile device center.
kikimax said:
Ok, so how can I change differents roms if my phone does not sync. with my pc, I used to able to do it, now for some reason I can't.
thank you for yor reply,
Henry
Click to expand...
Click to collapse
if yo uare flashing DAF roms the nyou go intothe bootloader and flash
most roms these days are CWM based and you install themn via zip file from the sd card no need for the computer
Ok, let me try to explain myself better so you can try to help me, thanks.
I did install the magldr 1.13 on my phone, when I plugged the phone to my pc for the first time it showed that it was intalling the driver and that went ok, my problem is that I don't see my phone on the screen so if I want to flash another rom how do I know that my phone is comunicating with my pc, my friend tells me that the minute he plugged he's phone to his pc, he sees his phone on the screen.
Can you help me?
Thanking everyone in advance,
Henry
have you tried removing and reinstalling wmdc? once just because of that i had to format my pc
1. You need to enter magldr bootloader, just reboot the phone and hold the on/ off key until you get on the magldr options screen. With your usb plugged in, scroll to usb flasher and confirm the option by pressing the call button.
Then open the rom you want to install in your PC and go for the flash. If the phone is not connected, then it shouldn't do anything. If it is, it will install.
2. Other option, from what I'm reading, I think your driver might not have been installed properly.
Try connecting the phone to other PCs. And do the usb flasher thing.
Let me know if this helped.
Sent from my HD2 using my fingers.