hi i am trying to upgrade my Typhoon to 6.1 but i haver got to the point in the upgrading process in which i need to restart and press 0 for the IU the only issue is i do not recive this message and i cannot get any further.
Edit: my SPL is 2.05.0130
you must go to the patched SPL 1.09 for Typhoon befor you go any further.
yes it is true said tobbie, with 1.09 SPL you can flash any rom like WM6.1 or WM6.5 on your Typhoon
for SPL 1:09 Can you get HERE
oh well ive tried poatching the spl before but i just recive errorr 260 or 240 and i cannont make no progress i have tried using a different computer but to no avail
oh well... if the device is still original, then you must follow a sequence of actions to allow such upgrade.
These should be mentioned in any custom rom thread. Essentially you must get the SPL 1.09 on the device then you can load any custom ROM.
1. application unlock the old OS
2. CID unlock the device with lokiwiz toolset
3. load SPL 1.09
4. load custom ROM
good luck!
I belive i have already application unlocked and supercided it with lokiwiz toolset but i have peforemd a hard reset due to that connection issue, would that haver affected it in anyway? thanks
If you are back the old WM2k3 and you cannot upgrade the SPL, then lokiwiz probably has not super-CID your device. To check, connect your device in Bootloader mode to mtty (with AS having USB disabled) and enter "info 1" (no quotes) then try "info 2" (no quotes) and report both results.
Not sure about above myself as I have no device at hand today to check right now.
Hard reset does not affect the CID or SIM Unlock - these are stored in the encrpyted area of the ROM (64kb Block) that is not affected by Hard-Rest or OS-flashing.
sorry for my noobiness but it will not show in mtty i have tried the usb drivers? but the phone does not show in mtty
You must make sure that Active Sync (Windows XP) or Mobile Device Center is not using the USB port to connect the device. You can disable the use in Active Sync selecting the "Connections" menu and then disabling there.
Reconnect the device and restart mtty. The USB button will be there only if the USB connection is accessible and the device is connected to the USB port.
sorry for the bump but ive came back to my phone and i am having so my trouble superCIDin the phone i have done everything by the book, ive hard reset the phone and tried everything again and now SDA unclokder says "phone is not unlockable" and the lokiwiz.bat will not super cid it.
Look at mediafire in my kitchen folder here:
http://www.mediafire.com/?3tt15dyp4mbuu
the "...one time per device" ZIP has all tools inside. There is another (on board application unlock) that will do the trick. It installs a tool on the device, execute it there first and then start SDA Unlock. No need to reboot as the changed security policies are active immediately.
i downloaded your kitchen and i ran the htcunlock the the sda unlocker still says the phone is unlockable
So these Orange devices are quite resistant to application unlock. Did you notice that the HTC Unlocker kind of "remote controls" a registry editor? It may be that the changes did not really go through.
It is quite complicated and a lot of trial and error what you will have to do and I cannot advise in detail as I have no such device.
Key is that the application that changes the policy on the device is permitted to do so. Usually as well SDA Unlocker (remotely via the RAPI Policy) or the signed Registry editor controlled via HTC Unlocker can do that. It all goes to the registry keys in HKLM\Security\Policies\Policies where the relevant policy IDs have to assigned the right values (role permissions). You can use the free CE-Command (from ghisler.com) which has a registry tool built in or the same registry editor that HTC Unlcok controls to check if the values that the tools try to write are really written or not. I suspect they are simply NOT written. If you cannot find a tool that can change the policy, then there is another way around this:
The Gold Card method. Get the trial version of "revskills" from www.revskills.com and create a gold card with the device for the "Typhoon". With this card in the device, the SPL will allow ANY (also non Orange) signed ROM to be loaded. Use any non Orange shipped ROM for the Typhoon and load it to the device. This OS should allow to change the application lock and also allow the further steps.
Mind that ROMs for the Feeler or Amadeus have different key-handling (especially for the joystick) - so best you get also a Typhoon ROM for that exercise.
I think in the Tornado Forum was once a description how to unlock a Cingular 2125, possibly similar actions may allow you the first step. Not sure here though.
thanks for your help i beelive that your tool changes the registrey values correctly im nnot sure about this i have tried running it a few times but with the same results
Just to reassure that: Your device is not CID unlocked yet after all the trials you did? What does the SPL tell when you enter "info 2" in mtty connected?
Do you know how to work with a PC registry editor and to connect with the device? There are several that can do that, e.g. "Registry Workshop" or "Smartione" or "CE Regeditor". All these can connect to the device via Active Sync and read out the HKLM\Security\Policies\Policies branch.
Could you just post the export of that branch here?
You can also do that on board the device with CECmd, get into virtual two window mode, on one side go to the branch above (exactly, on top of the second "\Policies"), on the other in any file-directory, can also be root. Then on the registry side press "5" for copy and confirm to copy the "\Policies" branch to the other side. You get a text file called "policies.reg" - attach or post it here.
Finally you could search for the Microsoft tool "security configuration manager". This allows to select the security model "Security off" - once applied to the device the lokiwiz should run with success.
Related
Dear everybody,
I have also killed my 2 day old MDA compact 3 by using the PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap.exe (Feel really frustrated about it)
It will not load windows only
IPL 1.13.0001
SPL 1.13.0001
GSM 02.49.90
OS 1.28.0.0
I've tried a lot but nothing has worked so far. Now my last resort is using XDA tools to make a bootable sd card.
Is there anyone who make a file that the artemis can use of an SD card?
I would be very much obliged!
did you do CID unlock before installing new ROM?
CID unlock is not required for flashing the PDAMobiz Powermap 1.1.2 ROM. Just make sure you follow the right instructions. I did it and you can find it here:
http://forum.xda-developers.com/showthread.php?t=294830&page=2
But make sure that you have synced your Outlook data on desktop as there is something wrong with restoring from backup file the PIM related info (I use Spb Backup, but seems it is same with any backup application)
http://forum.xda-developers.com/showthread.php?t=295295
more info.
ianvanhaaren:
1. Please provide more info what exactly happens when you try to turn on your device.
2. What type of error you have when you try to re-flash device? At what percent it stops.
3. Connect device to USB, disable USB connection in activesync. Start mtty console, choose USB type connection (mtty attached, in case you need it).
4. type set 32 in console. send this output.
If CID area on device is corrupted, for the moment only imei-check who knows how to re-calculate this area. Even so, if device won't boot in windows it will not help. You need to connect to device thru jtag interface, in order to load modified spl into ram and perform writing into security area, to recover it. Imei-check says, they know jtag for Artemis.
It may cost you a bit of money.
If you have an option to send it to service center, do it. It would be your best choice.
Regards.
Hi to all in this forum.
I have one T-Mobile MDA Compact II PM200. In this forum i hound that his name is Charmer. I try to unlock it with Lokiwiz03a. Program give me a code but device says that code is wrong. I try with other software to unlock it and after that mobile work with SIM card but no signal
I reflash mobiele with WM6 founded her in the forum, not it have English (before have German) but again no signal. I try now to unlock it with Lokiwiz02a and choose CID unlock. Again no signal.
When device in Automatic search mode no found network. If in Manual mode found but unable to register in network. When i put mobile to my computer speakers no outgoing signal from mobile that's not normal.
What is the problem ?
Can onyone help me with information ot needed software ?
In moment mobile information is:
ROM version: 10.2.0.8 WWE
ROM date: 2/03/07
Radio version: 01.12.20
Protocol version: 4.0.13.23
Identity:
Model No.: WIZA200
Platform: PocketPC
IMEI: 35703700051525500
Hardware:
CPU: OMAP850
Speed: 195 MHz
...
I try to found information about this problem here in forum but w/o result.
10x in advance
Did you try to flash a new radio? 2.69 or 2.19?
No.
I found this files:
BREEIMG.zip
breeze.zip
inside breeze.zip are:
SSPL.exe
spl
breezessplv1.nb
inside BREEIMG.zip is:
BREEIMG.nbh
is this needed files for radio flashing ?
if not then what files I need to try with other radio version ?
I download Radio from ftp on this form for Prophet. And try with Prophet_G4_RadioRom_v2.47.11 but now mobile not start. Go to splash screen and after few seconds restart.
I try to put it in bootloader mode but ActiveSync can't make connection and for that flash software can't wreit new radio or flash into mobile.
I ry with:
1. dowenload this t-mobile official rom (http://www.tm-phonedownloads.com/files/RUU_Compact ll_2060227_20602110_021921_T-MobileUK_Ship.exe)
2. enter your Charmer into bootloader mode by pressing power + camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the Charmer to your pc (make sure your battery is fully charged)
4. run the t-mobile rom.
5. good luck!
but ActiveSync can't make conection.
?
If you are in bootloader Active Sync wont make a connection. Just plug in the usb cable into your phone while in bootloader and run RUU.
Cheers,
vlodeck.
I try with this 2:
1. T-Mobile official rom RUU_Compact ll_2060227_20602110_021921_T-MobileUK_Ship
2. Prophet_G4_RadioRom_v2.69.21
T-Mobile official rom RUU_Compact ll_2060227_20602110_021921_T-MobileUK_Ship
===================================
inside are this files:
EnterBootloader.exe
nk.nbf
README.doc
ROMUpdateUtility.exe
RUUGetInfo.exe
RUUResource.dll
Prophet_G4_RadioRom_v2.69.21
========================
inside are this files:
EnterBootLoader.exe
nk.nbf
ROMUpdateUtility_G4.exe
RUUGetInfo.exe
RUUResource.dll
phone not start normaly. just start and after 5sec restart. i put it in Bootloader mode (press Camera, Power_buton and Reset. then release Reset and after few sec. mobile goto in Bootloader mode). when conect USB cable ActiveSync not find mobile and this file not make upadte/conection: ROMUpdateUtility.exe and ROMUpdateUtility_G4.exe
if I try to start RUUGetInfo.exe windows says that this is not valid Win32 application.
then what RUU to start ?
how to flash other Radio into this mobile or to reflash it again to be alive ?
anyone will help me for my problem ?
in moment when i start my pocetpc it displays:
IPL 1.12
SPL 1.12.0000
OS 10.2.0.8
the row GSM .... missing.
in moment i can't make connection with ActiveSync. then how to flash again mobile ?
now i try to flash it with RUU:
http://www.tm-phonedownloads.com/download_manager_mda_com2.html
http://www.t-mobile.de/downloads/?r...ku3.3_38222_382117_026921_tmo_de_ger_ship.zip
but it gives a error
i try with this:
http://www.my-audio.net/xda/Univers...s/Universal_Upgrade_v1.30.68_radio_1.09.0.zip
but when software start flashing says that this Utility is not for my device and to find right
?????
I'm guessing that this universal radio upgrade is for universal
Download this:
http://www.mobione.pl/pliki/ruu_252_eng.zip
Extract it, copy the .nbf of the rom you want to upgrade your device with to the extracted RUU folder. Once copied - run RUU.
P.S. The problem with your device is that you have upgraded wm6 on 1.xx bootloader. Thats why the system doesnt start. If the method I described above doesnt work. Post me.
Cheers,
vlodeck.
now i can bootloader mode,
i did it but got this error while i upgrade my rom to newest rom 3.3...
i got this "invalid command 326": please check your NBF data, this NBF data cannot be used for your PDA Phone.
hi again to all
after long time i try to play agian with this brick-PM200 that haven't signal.
last time (before more 2 years) i write ROM and after that PM200 not start, only in Bootloader mode (3 color lines).
today i revive it when flash this:
HTC_charmer_upgradeut_noid.rar
(
EnterBootloader.exe
nk.nbf
ROMUpdateUtility.exe
RUUGetInfo.exe
RUUResource.dll
)
PM200 start, in begin fave full signal. after 30-40 seconds signal gone (but not test in/out call). i try to restart mobile, try hardreset, try manual search on operator - all no result.
on start i put near radio but power amplifier not work. i think that this is harware problem.
but not 100% sure.
is possible this problem to be from wrong radio settings ?
i try to write different radios for Prophet but every time get message "Invalid tool" and radio flashers stop.
i try with universal radio thata Vlodeck says but again this message.
what to do ?
before two days i repair one HTC Touch Elf100 and read that can sniff USB comunication to check Vendor ID and other ID.
but in my PM200 this not work. on Elf100 work easy like is writed here in forum.
when start wyty (or what's name is) make connections with mobile but after write:
ruurun 0
says that need password. if try with password for Elf100 not accept it.
what is the password for Charmer (PM200) ?
or if there is other way to get Vendor ID and other ID how ?
I can help you maybe. You need to downgrade to Aku 2.2 using the original utulity. Then the Radio will be downgraded too. But nobody knows the exact way on how to do that. (Maybe Vlodeck knows that?) I'll try to get it this week and tell you then.
As for the password try CHARMER. I have never been able to test it with MTTY cause I don't get in the right mode but I think the olny possibility is CHARMER. Just try it with whatever tool you want.
Hope that was helpfull
10x for answer.
next day will test password and post result.
how to downgread to aku2.2 ?
if you find solution please post it.
today i try but w/o success:
Cmd>password charmer
Cmd>ruurun 0
Cmd>getdevinfo
Invalid command : getdevinfo
For a help screen, use command ? or h
Cmd>
i try and with passwrod CHARMER. result is same.
what are commands for MTTY that supported Charmer ?
OK you have the same problem I have. You have Cmd> in the window. To get the comands and the password working you need USB> instead of Cmd>. That is the same problem I have and I don't know how to fix it.
in moment i use MTTY 1.42
before 3-4 days i repayr one HTC Touch Elf100. and this MTTY work find. no problem that write CMD not USB.
terminal show CMD> i write commands and mobile answer w/o problem.
but in my Charmer not answer.
possible reason is access password. but not sure.
There are simple comands. And for them you don't need SuperCID. I tried them and they haven't worked too. So I think there is something else with it. Maybe the Bootloader locks all comands and you need a password for that too. But I don't know about that.
@ChrBeck
you try to make SuperCID SD card to have full access to mobile. and after that to try flash it with RUU ?
next morning will try this.
p.s. now find this:
http://www.tm-phonedownloads.com/
http://t-mobile.iris-global.com
Well, we can't SuperCID and Security unlock a Charmer with a bootloader over 1.x at the moment. This is surely impossible. That won't work using a SD Card too. So I think you will not have any luck.
I have an HTC Innovation, Qtek 9100...also wizard i think, Os: 1.1.7.8
GSM 1.4.10, SPL 1.01, Ipl 1.01, The language is in french.
I want at least to change the language to english, but i want it also a little updated.
I don't know what g3, g4 means and how to find out what version i have.
Please tell me where to begin to upgrade the phone, here are to many post and are some terms i don't understand like g3, g4, ipl, spl.
I don't think the phone is locked.
I also have vista
Thankyou and please guide me a little.
Start Here
http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
You have a G3 device
Here is a link to flash an english rom to your device
ftp://xda:[email protected]_9100_RUU_Prodigy_10107105_Qtek_WWE_ship.exe
it is not an upgrade basically the same as you have now but in english
here is a link to all the files you need to unlock the wizard both sim unlock(any sim card can be used) and cid unlock( You can install any rom)
http://rapidshare.com/files/53377946/Wizard__CID___Sim_Unlocker.rar
password for rar file is scousemartin
Once you have all this installed, you can flash any wm5/6 rom available for the wizard
thankyou, u've cleared things up for me ...
just how u know that is ia g3 or g4, g i think g stands for generation right??.....
found the info from the links...thanks again..
lanst question, after u what is the best wm5/6 to install onto the wizard? what rom posted here? i see here some tnt rom, are they good?
I use tnt 1933 from here and have no problems with it ,i would use radio 2.19 as well,as people have issues with missed calls etc, a link for that is there too
I know you have a g3 as your ipl and spl are 1.01 if it was a g4 it would be 1.01.xx
http://forum.xda-developers.com/showthread.php?t=341550
download links are located in post 3
you know what is not working? the link to the original wwe rom, from the ftp, looks like it is not there anymore!? can u verify that? or is my computer the problem?
yes i have just checked it isnt available anymore, in fact none of them are there anymore. download my wizard unlock pack and unlock the wizard with lokiwiz2b how to is here http://forum.xda-developers.com/showthread.php?t=249474
hope this is my last question!
What i have missed or what am i doing wrong?
so, i installed the rom from your unlock archive and it is ok, my wizard is in english now
i tried my simcard and it works so that results that my phone is not sim locked so i didn't use any of the sim unlock tools.
now i try to flash the tnt rom and gives me : error 295 and says something like imposible to use on your device and says to use some newer nfb file
...and what is the extended rom?
now i am reading: You MUST have an IPL and SPL at 2.xx or higher (BOTH not just one or the other).
so this means i can't install this rom if i have ipl spl 1.01?
reading a tutorial while updating this post!, so i red that i have to install a tmobile rom before i can install any rom? is this true?
Which rom did you install the button rom? or the o2 rom?
if it was the button rom did you follow these instructions
1 - Unzip lokiwiz.zip to a folder on your desktop
2 - Copy EnableRapi.cab to your Wizard
3 - Execute the EnableRapi.cab in your phone. Wait for it to finish
4 - Guarantee that your phone is connected via activesync with the computer
press the windows key + r and type cmd and press enter to get a dos window,that way when lokiwiz finishes you will still be able to read what it says
5 - Click on the black dos window that has opened and type cd desktop then type dir /ad and then a list of all the directorys on your desktop will be shown then change directory to the lokiwiz2b directory and Execute lokiwiz.bat (on your computer!)
Extended rom is what it says, a part of rom that is in an extended partition, basically it contains customisation programs and important files for installing into the wizard when it is hard reset.
when you say you tried your simcard ,was it the same provider e.g. o2 that you were using before? If it is the same that wont make a difference, try a sim from a provider that you dont have like t-mobile.
Anyway simunlock just allows you to use any sim, cid unlock allows you to load any ROM which is what you want to do.
After I read http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
It says The WM6 does not work on PH20A2 (Harrier) (Audiovox PPC-6600 / PPC-6601 / XV6600)/ CDMA device! <-- that is my mistake
My mistake steps:
1. upgrade 2003 2nd edition to WM6 (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
2. use mytt <-- may not hurt (I see 4 color strip with "NO GSM" at the bottom, stuck in there. The PPC will stop if I remove the battery for a few seconds and put battery back)
3. Do hard reset, format the PPC (stuck in white screen, then do soft reset. The PPC will ""NOT"" stop if I remove the battery for a few seconds and put battery back)
reflash
Have you tried re-flashing with the original ROM?
AbuGWM5 said:
Have you tried re-flashing with the original ROM?
Click to expand...
Click to collapse
What do you mean reflash?
Does it mean that Reinstall the WM6, or install other OS like WM5?
However,Without activesync how can I do that?
OR reflash mean formart?
I try to fomart my ppc, but stuck in the white screen
You got to revert back to WM 2003 SE with your original OS.
April 1 said:
You got to revert back to WM 2003 SE with your original OS.
Click to expand...
Click to collapse
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
king2004c said:
I try to connect my phone under bootloader mode. However, both my computer and my notebook can not detect my Pocket PC.
Click to expand...
Click to collapse
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
rickwyatt said:
put you ppc into bootloader mode then put it into the craidle then go to startmenu on you computer
then go to computer then right ckick youll see properties click it
then system properties sould show click hardware then device manager
do you see windows CE USB Devices if you do then click it then you sould see microsoft USB Sync
if it dose then go here
http://wiki.xda-developers.com/index.php?pagename=BlueangelFAQhave
Click to expand...
Click to collapse
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
try to take out first SD Card and SIM CARD from your BA first before connect to your notebook/PC
king2004c said:
I tried to upgrade my win2003 2nd edition in ppc 6600 to WM6, but it seems that WM6 won't work with ppc 6600. Then,
1. I download the WM5 rom from http://wiki.xda-developers.com/index.php?pagename=Helmi
2. Try to reflash the PPC
3. I see that the PPC response
4. Try to do the reset after finished upload rom
5. Four color strip screen & "NO gps" and "5.02... WWE"
6. Try to restart again, and wait, result is the same
7. Try to go to bootloader mode, use mtty, do "set 14 0", "task 28", "task 0", PPC still keep the same. I have tried all reset, hard reset, etc
8. *** Try to reflash the PPC again, I find out that there is no current ROM when the ROM upload program try to read my current PPC condition.
Btw, I post the question to the FAQ too
Click to expand...
Click to collapse
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
xplode said:
You did very stupid thing, you have flashed GSM based rom to a CDMA device, the only thing you can do is to use WM2003SE, flash your device with its original or any CDMA (Harrier) based WM2003SE rom
Quick Howto:
Put your device in bootloader mode, put it on the cradle, start the upgrade including radio (the same version can be flashed on top of the previous one), this will fix your device, if it does not then after successful WM2003SE upgrade do the MTTY "set 14 0", "task 28", "task 0".
Keep me posted if you have problem
P.S.
WM5 and WM6 does not work on Harrier (CDMA Blueangel) device, i hope my instructions to help you to have at least usable device
Click to expand...
Click to collapse
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
king2004c said:
I can reboot my device now, but the bluetooth does not work (all other main function seem works OK). I hope there is some solution that help me to fix the bluetooth becuase I have a external bluetooth gps receiver which I need to use it with my ppc all the time. Please help
Click to expand...
Click to collapse
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
April 1 said:
Please understand what xplode wrote to you, you can not use the GSM ROM on your device, so dont try to check bluetooth etc, go back and reflash your device with the original ROM following what explode said above. Dont you want to save your device?
Click to expand...
Click to collapse
I have already find a CDMA rom. Now the only problem in my phone is bluetooth
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
xplode said:
Well describe the exact problem, BT does not turn on at all, or maybe it returns error of some kind?
Please be more specific
Click to expand...
Click to collapse
So far, I can use the phone without any problem. Previously, I tried to upgrade my phone because I want to use bluetooth headset to listen music. That can only be done in WM5 or later. Now I reinstall my CDMA version of WM2003. I find out that the bluetooth does not work due to expire of lincese key. Does anyone have any suggestion how I can over come it? I just want my phone back to exact a few day ago. Thanks
thanks
lincese
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
meehaa said:
Someone has posted the attached file and said that it can fix BT license expired error. I have not tried it myself since I dont face such prob, so use it on your own risk.
To use it - extract archive to your PocketPC and run EXE file.
Click to expand...
Click to collapse
Thanks, but does not work on my PPC6600
Hi everyone! This is my first post and I would like to thank You all for great job done on this forum, I'm rather beginner but already gathered a lot of knowledge by reading various posts
My first post will be about HTC Universal, that came to me few days ago. From first look it's an amazing piece of hardware and I would like to make it working, because (obviously) it is not
Uni's characteristics:
Black O2 XDA Exec
NAND Flash - DiskOnChip G4
Uni's behaviour:
after turning on is showing bootloader screen with some artifacts and following info:
R 1.17.00
G 42.53.P8
O D. 08.81 TML
can access bootloader menu (three yes/no settings, KITL) - same artifacts are here too
combination of backlight+power+reset gives black screen
hard reset doesn't change anything, screen with O and X is ok, with no artifacts
device is not recognized by PC so I cannot flash it (dev 0000, ven 0000 on windows / cannot enumerate on linux) - USB transmit lines are ok because situation changes after choosing KITL mode (every other is unrecognized)
Already done:
I thought it may be damaged USB port, but I succesfully managed to make it work after choosing KITL mode from bootloader menu (backlight? + reset). It doesn't accept any commands through mtty but at least installed in windows as HTC Sync Device (not remember correctly?) and showed some prompt in console (KITL$ ?).
I didn't really know what KITL is so i googled for other methods of unbricking and found amazing discussion between scholbert and roglio in topic about rescuing uni from scratch via JTAG. So I remodelled my adapter to the same as Wiggler2 and connected to mainboard. However, my situation, if I understand correctly, is not the same as scholberts or roglios was. I have working IPL and partially working SPL, that is, I think I have
Is there any method of writing SPL into ram and running it in this situation? Maybe then USB will be working and let me flash new firmware? I found solutions like this for some other HTCs but I don't really know how to load something into RAM, because it looks like it is unaccessible at the moment (errors in openocd, zeroes readed by urjtag). I'm working with newest openocd version, it recognizes PXA270 without problem, same as urjtag.
Or is it possible to restore Uni via KITL mode? Maybe I try to download software required in topic about Hermes and run it at some free time, but I have to connect my old windows box to internet
I'll be very thankful for every answer and I hope that this Uni will work once again
P.S.: I'm sorry if some of statements are not understoodable, I lack possibility of using english daily and practicing it, so my english is little poor
Best Regards, Karol
#------
Ah, yes, I forgot. Not black screen after combination of backlight+power+reset, but Serial + v2.01. Does not react to USB. If I connect USB first, then reset, it's "USB v2.01" - device not recognized. The same with SD card inserted -> reset -> "USB v2.01" -> took card -> unrecognized...
Welcome to forums,
Have a read on the thread just above this one, you´ll find almost all you need
Hi!
Thank You for your answer. I have already read this and other topics regarding "stuck at bootloader" and other problems, and tried all the provided solutions, with no luck
The main problem is usb not working properly. I'd rather not suspect hardware damage, because it works in KITL mode.
#---
I've done some more research. Downloaded and installed Platform Builder, and following instruction for hermes (changing only processor type) tried to run system through KITL, but with no success, image (awfully small - about 900kB) was downloaded to device, but there was no answer from it - KITL screen have not changed.
After few tries I focused on another method - based on tomal's SDFlash_G3. I took 416 byte header found later in topic about SDFlash (OllieD's) and connected it with decrypted official nk.nbf image from O2 and later with one from tomal's rom.
My device was reacting kind of strange while trying to recognize rom from card. For first, it haven't tried at all, not until I !removed! MMC card! (instead of this later I was hovering the sd card slot pin responsible for card detect).
Then, there was two scenarios:
first, when I took card too fast after entering bootloader, it showed message about too short rom
second, where I waited some more seconds, it showed error about sections=1 and not allowing to update
So I searched about this section=1 error and found that it is incompatibility between 416 byte header and rom image - header points that there should be more sections in rom, but there is only one.
Don't really know how to change it, is there any documentation about header structure?
In topic about SDFlash_G3 there was mentioned that this method is "without 2nd device", but I haven't found anything about "with 2nd device", is it worth giving a try?
Can someone provide me with mmc/sd card image (compressed of course) with backup from G4 Universal device done with d2s command?
I'll be very thankful for any help.
Best regards, Karol