my computer restarted when i was updating and now when i turn the phone on i hangs on the black screen with SE logo on it...when i put it in bootloader mode(volume down+power button) it vibrates and doesnt show anything at all, the update service recognises it but it says that i have the newest version installed and i dont have the option to reinstall...i tried to remove the db folder from sony ericsson folder, but that didnt do anything, can someone tell me how to fix that problem?
Related
Hi, I bought a Sony Ericsson Xperia X2 and decided to update the firmware through SE Update Suite. In the middle of firmware update, the computer BSoDed on me. The phone went dead and the PC did not detect it any more (Unknown USB device in device manager).
Eventually I managed to detect the phone by SEUS (on another machine); now I have a "COMXX SSE X2 Software DOWNLOAD" in device manager. I follow the instructions in SEUS to update the firmware, press and hold Vol Down + Power buttons. The phone vibrates and device manager shows "COMXX SE X2 Software DOWNLOAD", but SEUS does not update the phone.
What can I do to recover the phone?
update firmware
How can I update firmware from card?
bdadabayev said:
How can I update firmware from card?
Click to expand...
Click to collapse
???
You have to do it through SEUS.
don't worry
this happened to me too. heres what you do read all the steps before you do it
first go ahead and charge you phone just plug it into the wall then follow these directions
1.) start suess and continue like you normally would
2.) remove your battery cover and leave it off
2.) when you get to the step that asks you to plug in your phone, connect your phone via usb to you computer, then hold the down volume button + the power button + while you are holding these buttons push the soft restart button* do this all at once and do not let go of any of the buttons until you see the white screen with the sony ericson logo and it should update like normal.
*to get to the soft restart look at the back of the phone with the battery cover off, now pull out the stylus right there next to you camera where you stylus came out is a little button push it with your stylus.
this worked for me when i thought i bricked my phone and it worked, so good luck and tell me how it works out
doministry said:
???
You have to do it through SEUS.
Click to expand...
Click to collapse
Can I flash without SEUS, other methods?
yummy-fun said:
this happened to me too. heres what you do read all the steps before you do it
first go ahead and charge you phone just plug it into the wall then follow these directions
1.) start suess and continue like you normally would
2.) remove your battery cover and leave it off
2.) when you get to the step that asks you to plug in your phone, connect your phone via usb to you computer, then hold the down volume button + the power button + while you are holding these buttons push the soft restart button* do this all at once and do not let go of any of the buttons until you see the white screen with the sony ericson logo and it should update like normal.
*to get to the soft restart look at the back of the phone with the battery cover off, now pull out the stylus right there next to you camera where you stylus came out is a little button push it with your stylus.
this worked for me when i thought i bricked my phone and it worked, so good luck and tell me how it works out
Click to expand...
Click to collapse
doesn't wurk, device unknown maybe you didn't brick your phone, that's why it was still booting to logo screen...
I noticed that "COMXX SSE X2 Software DOWNLOAD" device appears in Device manager when the Volume UP is pressed on boot instead of Volume DOWN.
One more thing... There is a useful piece of software out there called QPST (Qualcomm Phone Service Tool). When I have the phone in download mode it detects the device (since it's Qualcomm platform, pretty much like ZTE 3G modems). But I don't have loaders or software to flash the phone baseband from QPST. Maybe if someone can parse the firmware available on the Net and extract the said loaders and software, then I could flash the Baseband and get the phone detected by SEUS to continue flashing Windows part. Unfortunately, decrypting the firmware is way beyond my knowledge. Anyone more knowledgeable on this subject?
First of all: Charge your phone for at least 2 hours from wall charger. I have experienced that it does not charge from USB always, especially when in update mode.
Please try this if you have only charged from USB previously.
Prydplante said:
First of all: Charge your phone for at least 2 hours from wall charger. I have experienced that it does not charge from USB always, especially when in update mode.
Please try this if you have only charged from USB previously.
Click to expand...
Click to collapse
Thanks for your advice, but I am aware that phones don't always get full charge with damaged firmware. That is why I took the battery out and charged it fully with a special charger for batteries.
Need help
Can anybody help? - Problem is that i cant "push" my phone to go to bootloader (tried soft-reset, vol down+shut down..nothing helps), so it i cant update via SEUS. And after trying to instal manualy R3 cab's, "Clear phone memory" is gone - now i even can't reset my phone.
Anybody, please help.
what i think you trying to do is boot the rom from the sd card is that right? if you are, it won't work because you need a alternative bootloader or a hard-spl which the x2 doesn't have... yet. thats why we HAVE to use SUES. if you can't get your computer to recognize your phone even after charging it in you special charger and forcing it into bootloader via SUESS (the option i pitched earlier) your best bet is to contact Sony Ericsson or who ever you bought it from and tell them they sold you a faulty device and they HAVE to replace it. if you get the opportunity to talk to them on the phone be firm and don't ever place fault on yourself and push that they sold you a broken device, hopefully they will send you a new one. i'm sorry i couldn't help. At this time my knowledge in Winmo is ignorant at best. good luck
anyone know how to help?? i also have this problem.... ><
Down volume button + the power button doesn't have the logo of SE..
and the SEUS can't detect my x2... wanna cry//
Hi!
Do exactly like this:
1 Charge the battery with the wall charger to at least 50.
2 Remove all cables connected to X2. This is important!
3 Remove and re-insert battery.
4 Push and hold volume down.
5 While still holding volume down, push and hold Power at the same time.
6 Hold until SE logo on white background appears, then release both buttons.
7 Now connect USB cable.
Be careful to follow this exactly or it will not work!
x2 prob
I have same problem in my phone , during update with SEUS computer hang and now
my phone shows only vibrate.
i have tried volume down+power+reset
but it can't go to white screen or sonyericsson logo.
any other solution
bdadabayev said:
Thanks for your advice, but I am aware that phones don't always get full charge with damaged firmware. That is why I took the battery out and charged it fully with a special charger for batteries.
Click to expand...
Click to collapse
Or You might need go to " C " drive - Progam files _ sony Ericson than remove any SEUS in that folder befor you go to inStall new F/Ware up date , everytime you want to reflash new SEUS you have to remove the last time F/Ware evenly that is the same one SEUS .than you go on for update new F/Ware SEUS to your phone .
Here is the support site for US. SE has a dedicated Nr and mail for x2.
what about new's for xperia x2 flashing
i have one stuck on logo after installing cab
and seus say's that no new update
Rise said:
I have same problem in my phone , during update with SEUS computer hang and now
my phone shows only vibrate.
i have tried volume down+power+reset
but it can't go to white screen or sonyericsson logo.
any other solution
Click to expand...
Click to collapse
same problem i have
is there anythng new?
what to do is any way to fix it?
X2 morto !!!
I have the same problem, now I try to modify the language of my phone, just missing to finish the installation program displayed an error message and now I can not in flash mode puts you ... what friends do?
hi everyone.
I have this Xperia X2 which is stuck in FTM mode. I tried using SEUS but it says no updates available. I also tried the phone repair option in PC suite but when i press Power and Volumn down it gives me a blue screen with Sony ericsson logo and says Sony ericsson software update on top. Please help me. I appreciate your time
Hi,
Dears, I've try to install another ROM on my Xperia X8, and I've copy all required
files to "system\bin" and every things is coming well.
When try to enter to recovery mode by pressing "Back button" after SonyEricsson
logo is appeared the recovery window isn't come !
So can anybody help me in this issue ?
I know it's not clear to understand this but I'm not able to explain :S
Regards,
if you really copied them, and it didn´t say "cannot paste here because file system is read-only" there are two possibilities:
1. You pressed the button when the white "Sony Ericsson" appeared, but you long-pressed it.
Press it as often as you can (don´t worry,it´s not really difficult)
2. You pressed it when you saw the bootanimation, which is also SE logo, but it´s animated.
You have to press it when you see the white SE.
Hope I could help.
Have you installed Busybox?
if you really copied them, and it didn´t say "cannot paste here because file system is read-only" there are two possibilities:
1. You pressed the button when the white "Sony Ericsson" appeared, but you long-pressed it.
Press it as often as you can (don´t worry,it´s not really difficult)
2. You pressed it when you saw the bootanimation, which is also SE logo, but it´s animated.
You have to press it when you see the white SE.
Hope I could help.
Click to expand...
Click to collapse
Hmm, I' ve press it when the SE logo has appeared
I'll try again and update you
Thanks,
Sent from my LT15i using Tapatalk
When i done with instaling ROM (Froyo or GXgin 5.4) i restart phone in xRecover and when Sony Ericsson logo disapears second logo apears and never disapears. Phone never turn on in operating system. But when i restore to default ROM it turn on. Where is the problem? Help me i'm noobeee
andriss4461 said:
When i done with instaling ROM (Froyo or GXgin 5.4) i restart phone in xRecover and when Sony Ericsson logo disapears second logo apears and never disapears. Phone never turn on in operating system. But when i restore to default ROM it turn on. Where is the problem? Help me i'm noobeee
Click to expand...
Click to collapse
You are facing a bootloop. If you can enter xRecovery, try making a full wipe.
Suhaib Haidar said:
Hi,
Dears, I've try to install another ROM on my Xperia X8, and I've copy all required
files to "system\bin" and every things is coming well.
When try to enter to recovery mode by pressing "Back button" after SonyEricsson
logo is appeared the recovery window isn't come !
So can anybody help me in this issue ?
I know it's not clear to understand this but I'm not able to explain :S
Regards,
Click to expand...
Click to collapse
After you copy the 3 xRec files in system/bin, long press on each xRec file, tap permissions and tick all boxes. Reboot phone and when the white Sony Ericsson TEXT appears (not the logo with the round thingy), start tapping the back button, don't long press it, just keep tapping it fast till the xRecovery menu shows up.
And yes, make sure you have installed busybox from the market.
thanks, it helped
now using minicm 1.0.2. but... when i'm trying to install other rom like froyobread v016 the installation aborted cause by edify....
anybody have problem like me... plz help
The problem is still exist,
I've press the Back button a lot of time when SonyEricsson is appeared
and I've give the three files " Full Access Permission ", but nothing new.
Thanks for all, and I'll try to do it again, so any body have any advise ?
Regards,
Please help me. I am in a sort of panic right now.
I have a ZTE Blade C2 v809, sold here in Portugal as Meo Smart A12. It was rooted and working fine. I was however getting some error 24's trying to install apps. I thought this might have had to do with using Titanium Backup to remove TouchPal (I did make a backup first), so I decided to restore TouchPal. There were however some errors in the restore and it was stuck there, so I decided to reboot the phone.
Chaos. Now it wont boot. If I press the button normally, the phone boots, I see the android logo, the screen goes black (Not shutdown black, a sort of light black background) and nothing happens. If I try to boot into Recovery mode by holding the power button and the volume down key, I just get the android logo stuck there, nothing happens. If I hold the power button and the volume up key, I get the picture of that laying down android with the message error.
Any more info I must provide please tell me, I am desperate for a solution, If I lose this phone I wont be able to get another one.
Okay I fixed it. Turns out the recovery menu DID work if I waited for a long time and tapped the screen. Used the update.zip available from the site, and it works like a charm
Yay, I bricked my phone, too.
I did something similar, changed recovery-from-boot.p name to recovery-from-boot.p-bak and install-recovery.sh to install-recovery.sh-bak
Now the phone doesn't boot properly, in fact it's stuck in a boot loop:
>starts
>shows white ZTE logo on screen
>restarts
Tried connecting the phone via USB cable and used fastboot devices & adb devices commands, no devices found.
Also tried pressing "power + vol down" and "power + vol up", nothing. I can't enter recovery mode or bootloader.
Apparently the remaining way to get in it's trough the SD slot, or maybe there's another way.
I kindly ask for help, couldn't be possible that I ruined this cell phone so fast.
Ideas, somebody?
Hi all,
Its my son's phone. Suddenly the phone froze, had to remove battery to switch off anf on. Thats it.. from that moment it doesn't turn on. The brand logo comes up and pressing vol up+ power didn't take me to recovery mode. I tried several keys but nothing.
When connected to the pc, on device manager it shows "android phone" and th subtitle is adb interface!!
Please help snd advice thank you