Galaxy S will not boot past the "Galaxy S" screen on startup - Galaxy S I9000 General

Hi Everyone
my Galaxy S will not boot past the "Galaxy S" screen on startup. I have read several posts with the same problem and I have tried all suggestions that I have come across. Here is what I have tried so far:
Removed battery and sim card for several hours - no change
Went into recovery mode (volume up + power + home button). Received a "E:Can't mount /dev/block/mmcblkOp1 (No such file or directory)" and "E:copy_dbdata_media:Can't mount SDCARD: copy default media content failed." error messages.
In recovery mode, performed a "wipe data/factory reset" to restore the phone back to default - still no change
Do i need to send my phone back to Samsung or take it to a phone shop? or can it be sorted at home?
Brian

Did this just randomly start to occur? did you drop the phone? or did you try to flash another rom & thus got stuck on boot?
If not, have you tried going in to download mode? (volume down + power + home button)

Go into download mode and flash a new ROM including bootloader. You should also tick 'Re-Partition' in Odin and use a PIT-file.
Sent from my GT-I9000 using XDA Premium App

Lunchbox115 said:
Go into download mode and flash a new ROM including bootloader. You should also tick 'Re-Partition' in Odin and use a PIT-file.
Sent from my GT-I9000 using XDA Premium App
Click to expand...
Click to collapse
This would have of course been my next suggestion assuming he can get in dl mode

Try this.

J 3 M said:
Did this just randomly start to occur? did you drop the phone? or did you try to flash another rom & thus got stuck on boot?
If not, have you tried going in to download mode? (volume down + power + home button)
Click to expand...
Click to collapse
I have tried this and can get into the menu but no matter what option i said pick nothing works
Tbh i am not very good at all this lol
It happened because when i conected to Kies it said i need to update so i did and half way through the 2nd update 29% it crashed and now wont work
So the phone can be sorted?
Brian

jamesythfc said:
I have tried this and can get into the menu but no matter what option i said pick nothing works
Tbh i am not very good at all this lol
It happened because when i conected to Kies it said i need to update so i did and half way through the 2nd update 29% it crashed and now wont work
So the phone can be sorted?
Brian
Click to expand...
Click to collapse
Well if you can get into the dl menu your phone is just fine.
Did you read jcspecs posted link?
When you go into download mode it means your phone is ready to flash new software, roms etc, it requires the use of a simple program called Odin (3.1 being the usual preferred choice), from there you install selected roms into it's interface, you then plug in your phone (in download mode) & you let it do it's thing, all being well you'll reboot & your Galaxy S will be born again, only bigger, better, stronger & faster
Let me encourage you into a simple set up to get your phone up & running before you do anything else, once done you can then spend more time reading a lot of stuff just like most of the rest of us has had to do, once you read you'll will be in a better position to decide whether to stick with what works or whether to change, the key is finding what you can & can't do, what works for you etc, trust me you'll get the hang of it & it's well worth it!
I'm assuming your phone is Galaxy S I9000? READ CLICK--> THIS <--CLICK GUIDE THOROUGHLY!
Also take a look at THIS for I9000 models
The idea is to flash your phone back to stock firmware using the correct tools & to then flash over it with seriously better software to show you just what it can & should look & behave like, it'll also hopefully stop you from ever connecting to Kies again.... READ, READ, READ
Also watch the youtube videos by Totallydubbed provided in the links, they will seriously help you out.

simply, Brian, I want to introduce this method for you.
Make yourself understood what is ODIN flash. Please try to search this forum or do a google search. I suggest you use the offical 2.3.4 JVP rom.
ODIN to flash the room.
1st of all, make sure your phone model definitely I9000, no T959 or others.
2nd, don't connect the KIES, and in the settings-->application-->(click this) USB debugging.
3. Download the relevant files for flashing rom. Sorry, I have no link 4 U yet, but I hope it can help.

minishe said:
2nd, don't connect the KIES, and in the settings-->application-->(click this) USB debugging.
Click to expand...
Click to collapse
You should also close all Kies-processes (the one in the taskbar right at the bottom (Win7) too.
Sent from my GT-I9000 using XDA Premium App

Thanks for all the replies its all becoming a bit clearer lol
I have just done the 3 button's and i have on the screen the following
Android system recovery <3e>
Enter:OK key, select : vol up/down
Reboot system now
apply update from sd card
wipe data/factory reset
wipe cache partition
coping mdeoa files...
successfully copied media files.
#manual mode#
appling multi-csc
installing multi-csc
can't access to '/system/csc/ora/system/'.
successfully applied multi-csc
Is this the down load mode people are on about?
Brian

No its not when u have ur phone off press volume down the middle button and power button at same time it will get u into download mode pressing up volume and middle button and power will get u into recoverymode get it? So from download mode hook up ur phone to the computer use odin to flash a new rom to your phone using a pit file a pda file a phone file and csc file load those on odin and press start button make sure u got repartition cheked on and the other two auto reboot and freset time amd press start and you are good to go.... u can get those specific files on the xda website it depends what u want to flash u can go back to 2.2 froyo 2.3.4gingerbread is newest hope this help
Sent from my GT-I9000 using XDA Premium App

jamesythfc said:
Is this the down load mode people are on about?
Brian
Click to expand...
Click to collapse
No that is recovery mode
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This is download mode
As I said, You should watch the great videos by Totallydubbed in those links to get familiar with a few things.
The button sequence for download mode is long press (volume down + power + home button) until that image appears, be careful not to press too hard on those keys m8, you're gonna need them, let us know how you get on.

Thanks mate, i have managed to get into the download mode, just need to sit and go through what i actually have to do now
Brian

Is Odin3_v1.3.exe any good have found one but not sure
All the others have far too many links for me to understand lol
Brian

to be honest, if kies crashed your phone, and you aren't very tech, take it back and while you are at it remind samsung what a piece is sh*t kies is! It happens all too often and its about time they sorted it, failing that you can try as a above posts, and use odin to flash brew firmware
Insanity cm 016/glitchv10c

slaphead20 said:
to be honest, if kies crashed your phone, and you aren't very tech, take it back and while you are at it remind samsung what a piece is sh*t kies is! It happens all too often and its about time they sorted it, failing that you can try as a above posts, and use odin to flash brew firmware
Insanity cm 016/glitchv10c
Click to expand...
Click to collapse
Hah yeah couldn't agree more m8, I found that out 2 weeks after buying the phone, still, it's better to learn the fix now & just how to get the best out of the phone
jamesythfc said:
Is Odin3_v1.3.exe any good have found one but not sure
All the others have far too many links for me to understand lol
Brian
Click to expand...
Click to collapse
Brian, give THIS a go & READ!
Odin & pit HERE free download & then unzip/unrar it.

J 3 M said:
Hah yeah couldn't agree more m8, I found that out 2 weeks after buying the phone, still, it's better to learn the fix now & just how to get the best out of the phone
Brian, give THIS a go & READ!
Odin & pit HERE free download & then unzip/unrar it.
Click to expand...
Click to collapse
Duly agree as you will see from my sig, however he did say he was non tech so sometimes the safe route is the best!
Insanity cm 016/glitchv10c

I have downloaded Darky Resurrection 10.1 file i have used Bitzipper to extract it but when i open Odin 1.7 i can find the PIT file but not the PDA file?
Please help this is driving me mad lol
Brian

At first you have to flash a Gingerbread-firmware from Samsung (NO custom-ROM) containing Gingerbread-bootloader with Odin (flash with PIT-file and Re-Partition ticked) and then anither kernel that brings CWM to you and finally flash the custom-ROM with CWM.
Sent from my GT-I9000 using XDA Premium App

Brian,
It's easy to get confused with too much reading but the answer to your problem is already provided for you in the links however we'll try this.....
Flash Ficeto's Odin JVH base rom here it will root your phone & ready to go to Darky's
As provided
1. use Odin 3.1.3 to be 100% safe, make sure phone is not connected! then press pit file & track to the pit 512 & make sure repartition is ticked!
2. press PDA & track to the TAR file in the Ficeto folder, (do not unzip it!), assuming you've done this correctly you can put the phone into download mode
3. Once in download mode connect phone & wait 10-15 seconds before pressing start.
4. Assuming all of the above steps have went well the phone will be up & running & you can begin to set it up, accounts, wifi, settings etc, once you've done that check back here & let us know & we can then get you to the next step.
Please also say how strong/good your wifi, 3G, call & internet signals are too as you may need to flash through a few different modems to get back to the same quality you had before, then again you may not, however this is a minor step after so just get flashing the roms first.
If for any reason you cannot find Ficeto's PDA/TAR file in the folder it means you've downloaded the CWM version = (clockworkmod) instead, CWM is how you flash roms from an already up & running phone via the power button, so if this is the case just make sure you download the THIS ODIN VERSION from the link provided.

Related

[Tutorial] How To Restore Verizon Galaxy Tab Back To Stock

If you are here the odds are you are looking to take your Verzion Galaxy Tab back to the default setup for one reason or another.
Here are the steps you will need to take.
First let's make sure you have all the files and things are set up for this.
Hemdall
Download Heimdall from HERE, this is the program you are going to use to flash the needed files to your Galaxy Tab. I am putting the version I use on my sever just in case.
But here is a link to the developers page so you can download the original if you want.
http://www.glassechidna.com.au/products/heimdall/
You will also need *Microsoft C++ This also needs installed on your machine because it has .dll files Heimdall uses. (I use Windows 7 and did not need to install this [I think])
Now you will need to install the drivers the is also needed for Heimdall. unzip heimdall and go into the drivers folder where you will see zadig.exe. Run this.
At the top you see options. Click "list all devices"
Then in the dropdown select Android USB composite device (or whatever it says). (NOT*mass*storage)
Click start and let heimdall download/install the drivers.
Files You Are Going To Flash To Your Tab
HERE is where you *are going to download the files needed to flash to you tab.* There are four files in total.
DOWNLOAD
cache.rfs
param.lfs
system.rfs
zImage
Ok, Let's get to flashing over the files and getting your tab back to normal.
1: Connect your tab to your PC
2: Launch your tab into download as it is already connected to your PC.*(Do this by holding the volume down and pushing the power button)
3: Go in to the folder " heimdall" and start " heimdall-frontend.exe"
4: Set up the files you are about to flash to the tab in side of heimdall.* It should look something like this.
THIS IS THE IMPORTANT PART!!!!!! DO NOT SCREW THIS UP - -* I AM NOT RESPONSIBLE!!
DO NOT EVER EVER EVER PUT ANYTHING IN ANY OTHER LOCATION. THESE ARE THE ONLY FILES YOU NEED.
zImage goes in both the Kernel AND Recovery slot.
system.rfs goes in Factoryfs
Param.lfs goes in Param.lfs
cache goes in the cache slot.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5: After you have the files in place click start to flash. ALWAYS make sure your battery is sufficiently charged or you will have MAJOR problems. (I had to push start a few times.)
After this runs you will more than likely boot loop. Power down, wait a few seconds and hold power and up volume to boot into recovery.*(NOTE, do not hold power too long, just long enough to turn it on, then continue holding up volume till you see recovery. WIPE DATA AND CACHE. Tab should boot.
Note, if heimdall fails at the very beginning, just try unplugging and turning off the tab, close, and relaunch heimdall. it will eventually start. sometimes you just need the right combo of plugging in launching the*program.
After this is should be just like you took it out of the box, other than still having root access.
Hope this helps!
Aslo, I did not do any of the work here other than test it out and retype what is on this site to make it available to those on XDA and if you read my blog.
http://www.droidforums.net/forum/samsung-galaxy-tab/113084-how-restore-vzw-galaxy-tab-stock-dj11.html
All credit should go to mike919 at droidforums.net for putting this together!!
You can view his post here.
http://www.droidforums.net/forum/samsung-galaxy-tab/113084-how-restore-vzw-galaxy-tab-stock-dj11.html
Shameless Plug:
If this helped you out would you do me a favor and go to this site and vote/comment?
And pass it along to your friends as well.
Who Pees In The Shower?
Hope this helps some people out around here!
This should be a sticky... Just Saying
Thanks,
I tried to make sure I typed it as good as I could so people like me (mess things up often) would be able to pull it off and host all files I use so that nothing will change.
But I would like someone to look it over and make sure I did not miss something. We are all human after all.
And if there needs to be any other images people can think of to help more people out I will be more than happy to add them.
I cannot find ANY tuts like this for flashing roms, recovery, ect. You, my newfound friend, are the first. We need more exactly like this.
Sent from my SCH-I800 using XDA App
This is great stuff. I messed up a bunch of junk on my VZ galaxy tab and would like to go back to stock. Question about this guide: I've converted to ext4. Can I still follow the steps in this tutorial to return to stock or is there anything else that I need to do first? Thanks very much!
This post made even a retard like me dangerous enough to want to try flashing. Bump for the ext4 answer
Bobby Buggs said:
This post made even a retard like me dangerous enough to want to try flashing. Bump for the ext4 answer
Click to expand...
Click to collapse
Took the plunge anyway. Seems to have worked. Great tutorial!
Had previously used Koush's bootstrapper from the market to convert the file systems to ext4. Later tried to install KhasMek Voodoo Plus v3 kernel on my VZW tab and it nuked it (prob cause I did something wrong). Using these instructions, I got back to stock. Now to boot strap again and try, try again!
Thanks for the guide
fonixmunkee said:
Had previously used Koush's bootstrapper from the market to convert the file systems to ext4. Later tried to install KhasMek Voodoo Plus v3 kernel on my VZW tab and it nuked it (prob cause I did something wrong). Using these instructions, I got back to stock. Now to boot strap again and try, try again!
Thanks for the guide
Click to expand...
Click to collapse
Yeah, I think I get it wrong more than I get it right.
Last weekend I did this like 3 times in an hour.
Happy it is helping a few people out.
chaos67731, I saw in another thread you were having a hard time getting Koush's boot strapper from the market to work. Did you ever get a resolution for that?
fonixmunkee said:
chaos67731, I saw in another thread you were having a hard time getting Koush's boot strapper from the market to work. Did you ever get a resolution for that?
Click to expand...
Click to collapse
No, I tried a few times and did not have any luck. The only thing I am looking to customize with the Tab is really to have it over clocked a little.
I just got the Evo so after I am done setting that up and getting everything worked out I am going to try again.
But if I remember right when ever I run Koush's boot strapper the tab reboots and goes in to recover mode and starts to flash something. (I think, cant seem to remember 100% right now) . Then I get stuck on the Samsung screen..
At that point I am not able to boot back in to recovery mode to wipe anything, but I can boot in to download mode and restore the Tab.
I think I have to be missing something simple?
Got the bootstrapper from the market to work again on my VZW Galaxy Tab. Formatted the SD card and then tried it again...it worked great after that!
Sent from my SCH-I800 using XDA Premium App
fonixmunkee said:
Got the bootstrapper from the market to work again on my VZW Galaxy Tab. Formatted the SD card and then tried it again...it worked great after that!
Sent from my SCH-I800 using XDA Premium App
Click to expand...
Click to collapse
Maybe I am missing something?
Sent from my SCH-I800 using XDA Premium App
hi after restore to stock my screen in blank??help me
this was perfect
you wrote the directions clearer than water bro. thanks! i was dinking around for the 1st time with the tab and screwed something up. i'm back in business!
Your the best... got it first time Great work
- The Mike G.
Had a scary night last night with the old computer/phone/exclamation point error screen but this tutorial helped me out. Thanks a ton.
THANK YOU!
Thanks man! My Galaxy Tab (us cellular branded) was gone after a flash attempt gone bad (black screen and nothing more), but thanks to this tutorial it's finally back to life!!
I LOVE YOU MAN!
VZW Custom Kernel
So out of curiosity, is the Bootstrapper the only way to get a custom recovery set up for the Verizon tab? I used z4root and got the root access, but since then, I haven't had an opportunity to flash roms or kernels because of the lack of a custom recovery. Anybody think they could help ?

[GUIDE] How to use ODIN for dummies

I didnt find any step-by-step tutorials about this on xda, which is kind of weird and because i have spare time and its 3:19am I decided to make this tutorial
EDIT: If you are coming from eclair, install a froyo ROM and make sure it has a bootloader. Remember, if you cancel an installation that changes your bootloader, or stop it in anyway, you may hardbrick your phone. MAKE SURE YOU DON'T CANCEL OR TRY TO PAUSE THE INSTALLATION, JUST LET IT FLASH SMOOTHLY. use a laptop if you can, just in case an unlucky power surge would stop the flashing process
EDIT2: Here is a good Tutorial video from xda user Tejas Ahobala (if you don't know what he is doing at the start, dont worry. He is doing a factory reset before flashing):
EDIT3: A word from one of the commenters:
VelocityJump said:
Thanks a ton for this guide. I had rooted my phone a couple of months back but wasn't really able to figure out how to use ODIN to install a custom ROM all this while. A few pointers for others noobs...
1. The tip about some custom ROMs requiring a wipe data is important.
2. If you're already using CWM, use the 'shutdown' option and not the 'reboot' option when the phone reboots during the flashing process.
Click to expand...
Click to collapse
Here we go...
______________________________________________________________
Terms and words -->
Flashing ==> means installing a new ROM
ROM ==> is the operating system, any version of modded or un-modded android
Android ==> Google made operating system!!!
ODIN ==> Here, it means the program that you can use to flash ROMs on your phone (the phone im going to use here is samsung galaxy 3)
Soft brick ==> No, not the construction brick, this means you've got no working operating system or you have one but its damaged and you can't use it, so you cant see your homescreen, you only see a boot-loop when it wants to come up. You can view your recovery and boot loader (The download screen) when soft bricked, so you can easily fix this problem by re-flashing.
Hard brick ==> Similar to the construction brick, your phone with little hope of recovery without sending to the samsung base for repairs To avoid hard bricks, open the .TAR file which contains your ROM using winRAR, and check if it contains sbl.bin and boot.bin files or not. If it does contain, and you are nervous or this is your first time flashing etc, simply go and flash Kyrillos' ROM or Kyora ROM instead. (I'm not advertising, just stating a couple of ROMs that I know are safe) these ROMs can only soft brick your phone should the worse happen and there is no chance of hard brick
______________________________________________________________
Should this guide be followed carefully, nothing harmful can happen to your phone. Yet I wont take responsibility if something happens to your phone.
______________________________________________________________
**************************************
Remember to Backup your contacts and apps!
**************************************​______________________________________________________________
Stuff to download:
1) ODIN and a .OPS file, found Here, Or alternatively here.
2) The ROM, depending on what ROM you want there are different versions available. check This thread, the kitchens/ stock ROM packs part for stock ROMs, or if you want to try a custom ROM, try any other. I personally use Kyrillos' ROM, or Hillbeast's KyoraROM. Marcellusbe is praised highly by all for giving us the Cyanogenmod.
______________________________________________________________
1) Extract 'Flash tools.rar'
2) open Odin multi-downloader. This is how it's meant to look like.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
NOTE: Sometimes some random error message with a korean writing pops up. dont worry, it's nothing, just press OK every time you see it
3) Press the OPS button located in the 'Select OPS' section, as shown in the image below. NOTE THAT YOU SHOULD ONLY USE THIS OPS FILE IF YOU HAVE SAMSUNG GALAXY 3. YOU MAY ENCOUNTER SERIOUS PROBLEMS IF YOU USE THIS OPS FILE WITH A DIFFERENT PHONE. (works with i5800 and i5801 as far as I know.)
4) Browse for the 'apollo_0531.ops' that came in the rar file with odin and select it.
5) Tick the One Package option located on the left side of the application.
6) The ROM that you have downloaded should have a .tar extension. If its a .rar file, open it. If it has a .tar file inside it, extract it and use it, but if it has some weird ass stuff in it that only Jesus and Chuck Norris understand the meaning of, you need to use the 'free rar extraction frog' application to turn it into a .tar file. Download it for free from here.
7) The above step was just to confirm if you have the right file, so you dont get any errors. Now just select One Package button that is highlighted in the picture and browse and select the .tar file.
8) Make sure you have ticked everything that I have ticked. Use picture from part 5.
9) Go to your phone. go to Settings->Applications->Development and tick USB debugging if its not already ticked.
10) make sure you have the device drivers, just install Samsung KIES from HERE to make sure you do have the drivers. If the page doesn't show, just Google 'download samsung KIES'
11) turn the phone off, take the USB out, and press volume up, home button (the big fat button in between the menu and back buttons) and the power button together. hold them until you see the 'FORCE UPLOAD BY KEY PRESSING' screen. Now plug the USB back in.
12) Odin will immediately recognize your phone, and there will be a yellow label, like so:
13) Double check that you haven't missed anything.
14) Press start! HERE
15) You will see a blue download screen, saying please don't interrupt. PLEASE DON'T INTERUPT IT!!!!
16) The process will finish and system will reboot one or two times. go have some tea and come back 15 minutes later. You should have the Rom of your desire working on your phone.
NOTE: Some custom ROMs require you to wipe system data and then wipe cache. don't forget to do that! restart phone after wiping the data etc. If you've flashed a custom Rom and the device is showing a stupid triangle with an exclamation mark inside it, dont panic, press the menu button and you will see the menu (This menu is called the recovery menu).
EDIT4: How to flash kernels (on galaxy3/apollo/5800/5801)
METHOD 1==>
1--> you go to the kernel thread and download their kernel. it is to be a .tar file. (eg g3mod.tar)
2--> follow steps 3 to 5 from above tutorial
3--> put phone in download mode (step 11) and connect with usb
4--> in odin, select the 'select as one package file' option and browse for the kernel .TAR file. select it.
5--> check youve done everything. YOU SHOULD HAVE DONE EVERYTHING IN THE TUTORIAL EXCEPT THIS TIME INSTEAD OF USING A ROM YOU'RE USING A KERNEL!!
6--> There is no need for wipe unless otherwise stated by the developer.
7--> congratz man, you got yourself a new kernel!!
OPTIONAL 8--> download setcpu from xda (you can also download off market and pay for it for the donation)
its really usefull, it lets you control how much your phone uses the cpu and you can undervolt the cpu etc, you will find more info on the setcpu thread.
METHOD2==> (Only works for some kernels)
1--> go to the g3mod website and download the .zip version of the kernel. (there is a .tar and .zip)
2--> put the .zip in the root of your sd card
3--> go to recovery mode by either using kyrillos' rom (press & hold power
then choose reboot into recovery) or by turning the phone off and pressing volume up and down and the power button all together. select install .zip from sdcard and then select your .zip you downloaded before.
4--> it will install. no wipe needed unless the dev says so. reboot. HAVE FUN!!
HOW TO FLASH ROMS USING SYSTEM.IMG
1) Download system.img from safe source, preferably provided by dev, or any other trusted member who knows what they are doing.
2) Flash g3mod ROM.
3) Copy the system.img and paste into this path in your sdcard:
sdcard/android/data/g3mod/roms/**there are several folders here, just paste the system.img to the folder that suits the rom's name**
4) Boot into recovery.
5) Go to Multiboot.
6) Select desired ROM.
7) Done
________________
______________________________________________________________
THE GODDAMNED END.
Very nice
This is nice bro.....
If you can think of any missing tutorials, pm me, ill make some (might even make vid)
dhirend_6d said:
This is nice bro.....
Click to expand...
Click to collapse
all it took was about two hours
i may make vids about rooting and stuff as well, but im lazy and i think rudolf already done that, so im too late
the reason i made this was that when i first got my phone, it was february last year and the phone was running the eclair (so it sucked ) an i was being pushed by my friends that why i didnt have foryo and it took me literally something like 7 hours to find a 'followable' guide on flashing the xxjpa or something... anyway i thought having a really noob proof guide will be useful too ppl like me a year ago
nicely written
i was searching for tutorial like this 9 monhs ago and never found it with such detailed description
Sent fom Galaxy
Kyorarom Ascendency
a3 powered by
G3mod test 209 OC
Thanks it can help some peoples !
Moderator Message
Thread Stuck
Well done!! Good for the newcomers
Nice guide
doneeeee! easy
vol down + home button takes it directly into download mode
eeshlikhith said:
vol down + home button takes it directly into download mode
Click to expand...
Click to collapse
yea it does. what is the difference tho?
PersianSphinx said:
yea it does. what is the difference tho?
Click to expand...
Click to collapse
Simpler anyway nice guide! Detailed enough for any newbie! When i was new to thid forum i din understand much of all the guides but wif this im sure many more ppl will understand
Sent from my GT-i5801 using XDA App
Hello there!
I tried to do that, but in the middle of instalation of the room JPX/JP4 it failure.
And now my G3 turn on but don't work. It show a picture of a cellphone and computer and a exclamation point!
I tried to downgrade for 5800L, but odin and kied didn't link with usb.
=\
Any help?
xicoo ~ said:
Hello there!
I tried to do that, but in the middle of instalation of the room JPX/JP4 it failure.
And now my G3 turn on but don't work. It show a picture of a cellphone and computer and a exclamation point!
I tried to downgrade for 5800L, but odin and kied didn't link with usb.
=\
Any help?
Click to expand...
Click to collapse
Did you cut off the power or do anything that disrupted the flashing process? Tell us what you did explicitly
Sent from my GT-I9003 using xda premium
Question
Thanks for such a great tutorial.
I have a question.
Does sd card and sim card also needs to be taken out before one start flashing?
Also how long does this procedure take (the flashing process)?
Thanks
gauravgs said:
Thanks for such a great tutorial.
I have a question.
Does sd card and sim card also needs to be taken out before one start flashing?
Also how long does this procedure take (the flashing process)?
Thanks
Click to expand...
Click to collapse
Its not necessary. Flashing takes about 3~4min for me for it to boot up
Sent from my GT-I9003 using xda premium
bscraze said:
Its not necessary. Flashing takes about 3~4min for me for it to boot up
Sent from my GT-I9003 using xda premium
Click to expand...
Click to collapse
that's great.. 3~4 mins only. after that will I be able to use my phone in regular mode (making calls and restoring my address book) or I have to configure it?
Thanks
gauravgs said:
that's great.. 3~4 mins only. after that will I be able to use my phone in regular mode (making calls and restoring my address book) or I have to configure it?
Thanks
Click to expand...
Click to collapse
after flashing it will work like newly released from factory you can restore and all but depending on if you wiped device after the flasing process you will lose data, thats why i said make a backup of your important stuff before flashing
thnx bscraze for answering peoples questions while i was away
PersianSphinx said:
after flashing it will work like newly released from factory you can restore and all but depending on if you wiped device after the flasing process you will lose data, thats why i said make a backup of your important stuff before flashing
thnx bscraze for answering peoples questions while i was away
Click to expand...
Click to collapse
Ok
so should I backup my sdcard contents also on my PC (wipe data will clear both memories sdcard as well as phone's)?
or shall I leave it as it is?
I use titanium backup. Backed up all the user apps using it.
Thanks

[Tutorial] How to Flash and Root Galaxy A [SHW M100S]

This Model is even Older than the Galaxy S SHW M110S but still in the market in third world countries .
The Flashing Procedure for this Korean Galaxy A is similar to the Korean Galaxy S But this model has limited ROM's and Rooting Kernels as it was not that popular once the Galaxy S was revealed three months later.
Downloads
You Can download an Instructions manual from Here
You need to use Odin3 version 1.32 (Attached below)
You need USB Drivers (Attached below)
ROMS Currently Available
Stock ROM DB19
DF27
Galaxy A 2.2.1
EB25
EG04
EG04 Custom
EG04 Jackos
EI08
KyuHyuk 2.0.1 (Rom 2.2.1 Cooked)
Johyengho
Aprime GBV02
MiRu ROM PE 2.5
GA ROM 1.5
How to Root?
You can use Framaroot app or Unlockroot from your PC or Cydia Impactor from PC
or
Flash Rooted ROM EG04
Download Mode : Press and hold vol up + vol down + Power button
Recovery Mode : Press volume up + power button
General advice prior to Flashing any phone
Its always best to do a "clean" install. meaning you should remove any old scripts, data, cache, junk before flashing a new ROM, this is like taking a bath before using new clothes. For some models it is a must do, for others it may not be a major problem or can be resolved by flashing the dbdata.rfs to clear out the remaining junk that you failed to remove before flashing . But if you had "lagfix" and did not undo it, it can cause internal SD card unavailable situation, which can be difficult to resolve.
Hence before flashing its advisable to
a) undo lagfix, IF you had any.
b) Do a factory reset by settings>Privacy> factory reset ( erase SD Card - optional , as formatting SD card could be too)
c) And even going into recovery to wipe everything is also good.
d) Removing SIM Card and External SD card ( makes it easier for phone to boot up initially after flashing a new ROM)
Doing this will give you a "Clean" install or fresh start for your phone.
Make sure your Battery Charge is more than 50%, Samsung requires you to have 100% charge when using KIES to upgrade.
Reminder, What you do with your Phone is your own responsibility, so do it at your own risk​
Flashing Procedure
1). You need to Factory Reset Phone first go to settings >Privacy> factory reset also can be done in recovery
2) Power Down and Enter Recovery Mode and wipe data and wipe cache
3) Power down and remove battery, Then reinsert the battery and Enter Download Mode
4) Fireup Odin3 ver 1.32 on PC and Connect phone with USB cable to PC
5) Now select the ROM you had downloaded in Odin under PDA ( do not tick or press anything else ) and DON'T Interrupt flashing unless stuck for some time
6) Press Start Button on Odin3 and wait till is completed
7) Once phone has booted up and everything is working, power down and enter Recovery Mode, here you "factory Reset" phone one more time
That's it Now you will be using the new ROM you just flashed.
Any problem, just check My Android Solution's for relevant solution​
Check this out! You , YES! you are an " Android ". Not your phone but U.
You Must watch this documentary concerning your privacy Terms & Conditions we had agreed to, by using a PC or Smartphone
How to say Thank you? If you find any post helpful on XDA, please click on the Thanks button
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you are using XDA App or Tapatalk, long press on the post and select :good: Thanks Its easier to give "Feedback" in this manner than make an additional post.​
Its been 3 months & no one Replies to this thread ..
Really man ... This is a million $ thread ... I can just say WOW ...
Thanks
I am very thankful that i found this thread! At last! i am able to find roms for my phone. The sad part is, this phone was given to me, and i didn't know what they did because i found out that my Storage settings states Unavailable, and Available storage 0.00b. I tried flashing it with the stock rom you provided but an error that says like "the file is to large than tha target partition" something like that. Could please kindly direct me what to do? please! I would be very very thankful!
xggwarchildxx said:
I am very thankful that i found this thread! At last! i am able to find roms for my phone. The sad part is, this phone was given to me, and i didn't know what they did because i found out that my Storage settings states Unavailable, and Available storage 0.00b. I tried flashing it with the stock rom you provided but an error that says like "the file is to large than tha target partition" something like that. Could please kindly direct me what to do? please! I would be very very thankful!
Click to expand...
Click to collapse
You need to strictly follow the flashing guide , remove eveything including SIM card and Ext SD card, and format Internal SD card ( If possible) in the phone. After that following the guide flash the DB 19 Stock ROM, to see, if you can recover from the corrupt partitions problem.
Check this out! Links to useful Guides and " Banned " Documentaries ​
Sir, i did follow the flashing guide, but flashing the stock rom still say the same error: The file is too large than the target partition. BTW, there is no sd card in the phone while flashing. But still the same, stock rom say the same error, the other rom (custom?) succeed but still the same problem. Thank you!
Edit:
I think formatting the internal storage is impossible as there is 0.00b available in the phone storage status also the Format Storage cannot be clicked. Thanks!
xggwarchildxx said:
Sir, i did follow the flashing guide, but flashing the stock rom still say the same error: The file is too large than the target partition. BTW, there is no sd card in the phone while flashing. But still the same, stock rom say the same error, the other rom (custom?) succeed but still the same problem. Thank you!
Edit:
I think formatting the internal storage is impossible as there is 0.00b available in the phone storage status also the Format Storage cannot be clicked. Thanks!
Click to expand...
Click to collapse
The thing is , you need a PIT FILE to repartition, unfortunately, I cannot locate one, so you need to search for it. also I do not have this phone, for me to try extracting a PIT File or help you with other methods.
Alternatively, you can try to switch SD Cards, and that needs a modified CWM kernel as ell as an Ext SD card partitioned into two partitions.
Check this out! Links to useful Guides and " Banned " Documentaries ​
xsenman said:
The thing is , you need a PIT FILE to repartition, unfortunately, I cannot locate one, so you need to search for it. also I do not have this phone, for me to try extracting a PIT File or help you with other methods.
Alternatively, you can try to switch SD Cards, and that needs a modified CWM kernel as ell as an Ext SD card partitioned into two partitions.
Check this out! Links to useful Guides and " Banned " Documentaries ​
Click to expand...
Click to collapse
OK sir.. i will try and find if there is any existing PIT file for this. Thank you!
samsung galaxy a shw m100s
i buy samsung galaxy A shw m100s with firmware 2.3.4. this is my first android phone i am intrested in learning new things i download odin3_v1.3.2.exe with a tar.md5 file named {SHW-M100S_HOME_EB25_8G_REV08_user.tar} i connect my android with power+vol down+vol up key download mode and open the odin and upload the tar file i change the firmware 2.3.4 to 2.2.1. now it is hang when i turn on hotspot sheild opened i want to back in 2.3.4 and a stable operating system
please help me please
bhailogs121 said:
i buy samsung galaxy A shw m100s with firmware 2.3.4. this is my first android phone i am intrested in learning new things i download odin3_v1.3.2.exe with a tar.md5 file named {SHW-M100S_HOME_EB25_8G_REV08_user.tar} i connect my android with power+vol down+vol up key download mode and open the odin and upload the tar file i change the firmware 2.3.4 to 2.2.1. now it is hang when i turn on hotspot sheild opened i want to back in 2.3.4 and a stable operating system
please help me please
Click to expand...
Click to collapse
Follow the guide above step by step and after that flash the EG04 or EI08 ROM, it comes in custom, rooted etc or the other after EG04 , will get you back to 2.3.4, remember to do all the wipes and steps.
Check this out! Links to useful Guides and " Banned " Documentaries ​
Brother Is TheRe Any Jelly Bean Rom?????
flashing not starting
xsenman said:
This Model is even Older than the Galaxy S SHW M110S but still in the market in third world countries .
The Flashing Procedure for this Korean Galaxy A is similar to the Korean Galaxy S But this model has limited ROM's and Rooting Kernels as it was not that popular once the Galaxy S was revealed three months later.
Downloads
You Can download an Instructions manual from Here
You need to use Odin3 version 1.32 (Attached below)
You need USB Drivers (Attached below)
ROMS Currently Available
Stock ROM DB19
DF27
Galaxy A 2.2.1
EB25
EG04
EG04 Custom
EG04 Jackos
EI08
KyuHyuk 2.0.1 (Rom 2.2.1 Cooked)
Johyengho
Aprime GBV02
MiRu ROM PE 2.5
GA ROM 1.5
How to Root?
You can use Framaroot app or Unlockroot from your PC or Cydia Impactor from PC
or
Flash Rooted ROM EG04
Download Mode : Press and hold vol up + vol down + Power button
Recovery Mode : Press volume up + power button
General advice prior to Flashing any phone
Its always best to do a "clean" install. meaning you should remove any old scripts, data, cache, junk before flashing a new ROM, this is like taking a bath before using new clothes. For some models it is a must do, for others it may not be a major problem or can be resolved by flashing the dbdata.rfs to clear out the remaining junk that you failed to remove before flashing . But if you had "lagfix" and did not undo it, it can cause internal SD card unavailable situation, which can be difficult to resolve.
Hence before flashing its advisable to
a) undo lagfix, IF you had any.
b) Do a factory reset by settings>Privacy> factory reset ( erase SD Card - optional , as formatting SD card could be too)
c) And even going into recovery to wipe everything is also good.
d) Removing SIM Card and External SD card ( makes it easier for phone to boot up initially after flashing a new ROM)
Doing this will give you a "Clean" install or fresh start for your phone.
Make sure your Battery Charge is more than 50%, Samsung requires you to have 100% charge when using KIES to upgrade.
Reminder, What you do with your Phone is your own responsibility, so do it at your own risk​
Flashing Procedure
1). You need to Factory Reset Phone first go to settings >Privacy> factory reset also can be done in recovery
2) Power Down and Enter Recovery Mode and wipe data and wipe cache
3) Power down and remove battery, Then reinsert the battery and Enter Download Mode
4) Fireup Odin3 ver 1.32 on PC and Connect phone with USB cable to PC
5) Now select the ROM you had downloaded in Odin under PDA ( do not tick or press anything else ) and DON'T Interrupt flashing unless stuck for some time
6) Press Start Button on Odin3 and wait till is completed
7) Once phone has booted up and everything is working, power down and enter Recovery Mode, here you "factory Reset" phone one more time
That's it Now you will be using the new ROM you just flashed.
Any problem, just check My Android Solution's for relevant solution​
Check this out! You , YES! you are an " Android ". Not your phone but U.
You Must watch this documentary concerning your privacy Terms & Conditions we had agreed to, by using a PC or Smartphone
How to say Thank you? If you find any post helpful on XDA, please click on the Thanks button
If you are using XDA App or Tapatalk, long press on the post and select :good: Thanks Its easier to give "Feedback" in this manner than make an additional post.​
Click to expand...
Click to collapse
after i enter in to the download mode nothings gonna happen :'( :'( my device is not showing in the connection status :/
flashing not starting :'(
any solutions plzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz
my shw m100s is stuck at the upgrade screen i dont know what to do
Khizar hayyat said:
Brother Is TheRe Any Jelly Bean Rom?????
Click to expand...
Click to collapse
Sorry mate, This Phone was only sold in Korea and only a few countries. Few month later, Galaxy S came out and died. I remember many many developers back in Korea cooking ROMs but in about 2011, all the development completely stopped and the Galaxy A community closed. Gingerbread and Froyo ROMs are all we've got.
Thank you very much for the ROM

[Root] CFAutoRoot For SM-T807T/SM-T807P + Firmwares

Note: I did not make any of these root methods. Credits of the people who confirmed/ported cfautoroot is at the end of this post. I got permission to post these root methods here as most of the discussion happened in the General thread. I am not responsible for any damages done to your device. This will trip knox as always and this root method is only for the TMobile and Sprint Tab S 10.5! You've been warned!
Root is now available for these devices! Hope you enjoy and hopefully this should get some development going!
CFAutoRoot for SM-T807T(Tmobile)
Ripx88 confirmed T805 Cfautoroot works for SM-T807T, but you may have a broken recovery. He also confirmed that Twrp and Philz CWM for SM-T805 also works on the SM-T807T. Thanks to him!
Download: http://download.chainfire.eu/477/CF...-Auto-Root-chagalllte-chagallltexx-smt805.zip
CFAutoRoot For SM-T807P (Sprint)
Goriell ported Cfautoroot to this model. Props to him! Still awating for others to confim.
Download: https://mega.co.nz/#!eoB3TbxI!fdUUK-GJFfDx7ietfosnxxHHB2WN4tV0SGieQsdL9tA
Mirror: https://docs.google.com/file/d/0B5DZenb7A53cQldyRGw2TWhBeVk/edit?usp=docslist_api
Odin Download
http://forum.xda-developers.com/showthread.php?p=33970642
How to install
Make sure that in settings>general>security reactivation lock is OFF
edan1979 said:
Follow these instructions to the letter. Do not touch any buttons or checkboxes that are not listed below to touch!
- Download and unzip the CF-Auto-Root-....zip file (see posts below this one)
- If you end up with a recovery.img and cache.img file, you've extracted twice. You need to end up with a .tar.md5 file - don't extract that one
- (USB) Disconnect your phone from your computer
- Start Odin3-vX.X.exe
- Click the PDA (AP in odin v3.x) button, and select CF-Auto-Root-....tar.md5
- Put your phone in download mode (turn off phone, then hold VolDown+Home+Power to boot - if it asks you to press a button to continue, press the listed button, or run adb reboot download command)
- (USB) Connect the phone to your computer
- Make sure Repartition is NOT checked
- Click the Start button
- Wait for Android to boot
- Done (if it took you more than 30 seconds, you need practise!)
NOTE: Sometimes the device does *not* boot into recovery mode and root your device. Just do the entire procedure again if this happens. If it still will not install root and such, make sure that in Odin "Auto Reboot" is not checked. Then after flashing, manually shutdown your device and boot with VolUp+Home+Power button to boot into recovery manually. This will start the install process.
New to Samsung? Unfamiliar with Odin? Think all the above is a hassle? Get used to it. It's very simple, and us Samsung folk use Odin (or Mobile ODIN ) for everything! It's so very very convenient once you get used to it. Notice the 30 second comment above? For experienced users, the entire process indeed takes only 30 seconds!
Flashing with Odin
1. Put your phone into download mode. To do this turn the phone off and then press volume down+home button+power button at the same time. You will then get a warning saying press up to continue and down to cancel, press volume up and you are now in download mode
2. Start Odin
3.At this point please make sure that ONLY TWO OPTIONS TICKED are "Auto Reboot" and "F.Reset Time" (otherwise you could end up with a very expensive paperweight)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4. If there was only one tar file when you extracted the firmware put it in the PDA section.This just means this file contains the PDA+PHONE+CSC all in one firmware
If there are three files they should have one of PDA/PHONE/CSC in their names look for this and put them in the corresponding section.
5. Plug your device into the computer, wait for the drivers to install and then wait for the ID:COM section to turn blue.
6.ONCE AGAIN CHECK YOU HAVE NOT TICKED RE-PARTITION OR PUT IN A PIT FILE
7.Press start and the flash will begin, once this has started do not remove the usb cable or turn of your computer or the device the phone will reboot once the flash has finished.
Click to expand...
Click to collapse
Thanks:
-Chainfire for Cfautoroot method
-Ripx88 for confirming root working on T807T. Helped ALOT!
-goriell for explaining how to port and porting it to SM-T807P. Helped ALOT!
-Samsung
-Samsung updates for firmware... took me 14 hours to download and mirror
-Many many more
-Tkkg1994 for help on somethings
Post from main thread.
CF-Auto-Root is the root for "rooting beginners" and those who want to keep as close to stock as possible. CF-Root is meant to be used in combination with stock Samsung firmwares, and be the quickest and easiest way for your first root. In essence, it does nothing but install and enable SuperSU on your system, so apps can gain root access.
Donate
CF-Root and CF-Auto-Root have been available for many devices (over 50 different models !) and have clocked over 9 million downloads. This is not even counting custom ROMs that include CF-Root (non-Auto) kernels. Don't be a leech, buy me a beer (and use the "Thanks" button!). Imagine if every user had donated me $1...
What's installed
- SuperSU binary and APK
- Stock recovery (note that any other recovery you may have installed will be overwritten !)
What's the difference between CF-Auto-Root and CF-Root, and/or other root solutions ?
CF-Root (non-Auto) are manually built rooted kernels and/or flashables that usually provide more than "just root". CF-Auto-Root is built on an automated system that I am constantly improving that takes a stock recovery image and returns an automated rooting packages. These packages are designed to install and enable SuperSU on your device, so apps can gain root access, and nothing more.
The difference with many other rooting solutions is that those will often install a custom recovery for you (I am personally moving away from custom kernels and recoveries, for various reasons), while with CF-Auto-Root you will end up with a stock recovery again.
Not included - custom recovery
A custom recovery like CWM or TWRP is not included.
Not included - Triangle Away
Triangle Away can be used to reset the flash counter after installing CF-Root. The flash counter keeps track of how many custom firmwares you have flashed, as this voids warranty. (No idea what this about ? Read up on it, you will want to use this !)
Not included - adbd Insecure
As this CF-Root does not include a custom kernel, adb shell does not have root access by default (you can still get it by typing su inside the shell), nor is adb remount supported, nor will adb push and adb pull work on system files. adbd Insecure can be used to remedy this situation. (No idea what this is about ? Don't worry about it !)
CF-Auto-Root homepage
http://autoroot.chainfire.eu/
Bugs.
WIFI Bug Fix: In root explorer go into system/etc/dhcpcd/dhcpcd-run-hooks
It needs to have permissions fixed to "execute" by "user" "group" and "others" by using your favorite file explorer
this will fix your "obtaining ip address loop" without having to ever use static ip address- goriell
You know what.. here is the kernel and stock recovery for the SM-T807T.
Bop! https://mega.co.nz/#F!PwwT3JLQ!KHZNbb3ddgfStcdcB4rmlQ
Firmware to SM-T807T: https://mega.co.nz/#!ylYEBA4D!yWUPtuT60dLCIy_zCN_rqnN2L319oZYSCSFtOC_Pv6Q
Firmware for SMT807P: https://docs.google.com/file/d/0B5DZenb7A53caXhNQkhMb0NkMFU/edit?usp=docslist_api
Bop! Recovery and boot image for SMT807P: https://www.dropbox.com/sh/h5zw61wdn6rx319/AADS2Wb8OFDw3DxpuES7GI2Va?dl=0
Incase anything goes wrong Enjoy
Will look into this later this evening. I have been patiently waiting for a root method for my Sprint Tab S, so I'm really hoping this pans out. Thanks for posting the info!
wosiek said:
Will look into this later this evening. I have been patiently waiting for a root method for my Sprint Tab S, so I'm really hoping this pans out. Thanks for posting the info!
Click to expand...
Click to collapse
Please let me know if it works smoothly. I'm still in the process of tweaking it and looking for bugs.
Anyone have the firmware for the T807P? I see the T807T is up there, but think us Sprint users would need the correct firmware correct or we can run the TMo variant and be fine? Just want to confirm. If that is all we need. I'll go ahead with the process right now.
gorriel said:
Please let me know if it works smoothly. I'm still in the process of tweaking it and looking for bugs.
Click to expand...
Click to collapse
Hey do you have the firmware downloaded? If so can you mirror it for us? I dont have an extra 14 hours to download and upload the firmware
Tried to download the CFAutoRoot file (Sprint SM-T807P) from the link in the OP, but the webpage couldn't be found.
Anyone else experience similar behavior?
wosiek said:
Tried to download the CFAutoRoot file (Sprint SM-T807P) from the link in the OP, but the webpage couldn't be found.
Anyone else experience similar behavior?
Click to expand...
Click to collapse
Works fine for me. Are you on att? Mirror to google drive will be coming. Standby
Yeah, the WAN at the office is managed by ATT. Are they notorious for having issues with MEGA?
I'll try downloading again from home this evening - meant to do that last night, but it fell off my radar.
wosiek said:
Yeah, the WAN at the office is managed by ATT. Are they notorious for having issues with MEGA?
I'll try downloading again from home this evening - meant to do that last night, but it fell off my radar.
Click to expand...
Click to collapse
Att blocks mega because of the history of mega and copyright claims. Ill make another mirror with google drive.
For anyone having trouble with the T807P root please post information on what happened and I will try to troubleshoot it. It is suppose to be a quick and easy CFAutoRoot using ODIN. I will say that it doesn't work if you are trying to use Odin on a virtual machine. It will stop as it tries to upload the cache.img. There is something about virtual machines that blocks it or Odin just doesn't like.
Uploading Sprint firmware now Will also upload the boot.img amd recovery if a dev wants them.
CFAutoRoot For SM-T807P (Sprint)
Can you host the
CFAutoRoot For SM-T807P (Sprint) on something other than mega, Like Drive or Dropbox please. I have Time Warner and i can't download it for some reason.
kingakuma said:
Can you host the
CFAutoRoot For SM-T807P (Sprint) on something other than mega, Like Drive or Dropbox please. I have Time Warner and i can't download it for some reason.
Click to expand...
Click to collapse
Will do hold on
DUHAsianSKILLZ said:
Will do hold on
Click to expand...
Click to collapse
Thank you my good sir.
kingakuma said:
Thank you my good sir.
Click to expand...
Click to collapse
Here ya go https://docs.google.com/file/d/0B5DZenb7A53cQldyRGw2TWhBeVk/edit?usp=docslist_api
DUHAsianSKILLZ said:
Here ya go https://docs.google.com/file/d/0B5DZenb7A53cQldyRGw2TWhBeVk/edit?usp=docslist_api
Click to expand...
Click to collapse
Thank you worked great with Odin 3.09
I can only access odin download mode, i can't access any recovery, how can I flash back to stock?

Sprint has released Pie for S8 and S8+, flashing worked perfectly on my AT&T S8+

Hey guys I just got done flashing the G955USQU5DSC1 Android Pie Firmware that Sprint released for the S8/S8+ (and Note 8). The steps are below if you want to do it It's your risk and since we just had the first US carrier push the Pie update the others should be close behind but if you want it now this works perfectly. At least it did for me and for a few others I saw on reddit. I was able to do so without wiping my phone either, no data loss at all. Everything is working perfect, AT&T bootscreen, Wi-Fi calling, VOLTE etc.
Step 1: First off download and install the Samsung USB Drivers for Mobile Phones https://developer.samsung.com/galaxy/others/android-usb-driver-for-windows if you don't have them installed already (reboot after installing them) Use "SamFirm" to download the Sprint Firmware (no throttled download speed like most sites etc) I used v0.3.6 https://bit.ly/2Gso6QQ
Step 2: Launch "SamFirm" (I set the Auto/Manual check box to Auto) and input your model number (Settings>About Phone) or SM-G950U for S8 and SM-G955U for S8+
Step 3: In the "Region" field of "SamFirm" application put in "SPR" for Sprint, and click "Check Update". When you're ready to download it should look like this (G-950U for S8 instead of S8+) When you click download it will ask where to save the Firmware, I just saved to my Downloads folder.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 4: Once the Firmware download and decryption process is complete you can close "SamFirm". Go to where you told the app to download the firmware, right click it and click extract. Now it's time to use ODIN. At this point if you just want to be extra safe I would use Samsung SmartSwitch app on your phone to create a backup of your phone either to your MicroSD card (easiest) or to your PC. This will backup App /w app data, home screen layout, settings, documents, music (not needed if on your SD card) etc. But I didn't loose any data or have a reset when I did this.
Step 5: Download and open ODIN, I used ODIN 3 v3.13.1. Do the usual of clicking BL/AP/CP etc. then point ODIN to that file of the Firmware that is inside the folder you extracted (ODIN will take a second to scan each file as you add it, just wait for it to finish). For CSC make sure you select CSC do NOT select HOME CSC. If you select HOME CSC it will wipe your data/reset your phone. Also do not select the USERDATA file. Leave USERDATA blank in ODIN (at least for AT&T and Verizon users who this guide is for).
Step 6: Boot your device into download mode. Power off your S8/S8+, then press power and hold power, volume down, and bixby button at the same time. You should very quickly get a blue screen, release the buttons. The screen will say press volume up to continue, do so. Now plug your S8/S8+ into your PC. ODIN should show a blue square under ID:COM like in the previous photo. If ODIN looks the same as my screen shot while you're in Download mode you're ready to go. Now just hit start and wait for the process to complete fully. When it dose finish your phone will reboot and ODIN will show a green square with the word "PASS".
It may take a bit longer than normal for your phone to boot this first time. Also the first time my S8+ rebooted I wound up in the recovery menu, but simply hit the power button since the first selected item is "reboot phone" and the power button is the select button. If you get some white text at the bottom saying its doing something just wait for it to finish and when you get the reboot option hit the power button. That's it. After that my S8+ booted up just fine (this boot may be a bit longer as well but only this time) and I was at the lock screen. All my apps still installed, settings the same etc etc. Just like getting the update OTA.
Ive got an unlocked ATT S8+ and appear to be running into an issue when I fill in the info and select auto.
SamFirm v0.3.6.0
Error: Please specify a region
Checking firmware for SM-G955U/ATT/G955USQU1AQC9/G955UOYN1AQC9/G955USQU1AQC9/G955USQU1AQC9
Error: Could not send BinaryInform. Status code 200/400
Request was invalid. Are you sure the input data is correct?
Could not fetch info for SM-G955U/ATT. Please verify the input or use manual info
Click to expand...
Click to collapse
Thoughts?
UnboundGodz said:
Ive got an unlocked ATT S8+ and appear to be running into an issue when I fill in the info and select auto.
Thoughts?
Click to expand...
Click to collapse
You have to choose SPR for CSC code because ATT does not have a pie rom for SM-955u
I flashed it yesterday without any issues over the drl7 beta. Process took 15-20 mins but work like a champ after booting up!
Please read this instructions
Just finished flashing on galaxy s8 SM-G950u unlocked Verizon.it worked like a magic for me .BUT faced some issues like :
* after downloading firmware using samfrim error was crc not match please redownload file.
-Solution: download firmware without crc check option.
*after download and decryption. Trying to extract the downloaded file error msg ( file is corrupted)
-Solution :download 7zip software to your pc and right click on downloaded firmware file then choose check crc when finish right click again and choose 7zip > extract now you will see more then 4 files.
When finishing even if there is error just ignore and follow (Sean8102) guide
After flashing and your device restart you will see error message ..don't panic just do wipe cash and reboot u
Your device..now you can enjoy with android pie and give middle finger to verizon late updates
kumayam said:
You have to choose SPR for CSC code because ATT does not have a pie rom for SM-955u
I flashed it yesterday without any issues over the drl7 beta. Process took 15-20 mins but work like a champ after booting up!
Click to expand...
Click to collapse
Alright thanks, Ill be giving it a go. Curious, what are the benefits to flashing this version?
UnboundGodz said:
Alright thanks, Ill be giving it a go. Curious, what are the benefits to flashing this version?
Click to expand...
Click to collapse
Theres no benefit, it's the 9.0 pie rom update. If u tried the beta versions, it's the same except some
bug fixes. The branded ROMs are all the same, they Just add their own bloatware and other BS but other than that snapdragon rom is the same but are different than exynos rom versions.
Perfect guide.
Thank you very much! I use your guide and was able to flash without wiping any of my data!
omg THANK YOU!
So im doing something wrong, or the files just wont work for my version.
I've placed my device into Downloading Mode with two methods, using adb and the volume down, Bixby, and power button. But for some reason it appears to fail while connecting. Thoughts?
Here it is from these guys using google drive.
https://simunlockremote.com/galaxy-s-series-firmware/
https://drive.google.com/open?id=1YD2JZDalRYRavxLOXWslkrJu88FAJQro
UnboundGodz said:
So im doing something wrong, or the files just wont work for my version.
I've placed my device into Downloading Mode with two methods, using adb and the volume down, Bixby, and power button. But for some reason it appears to fail while connecting. Thoughts?
Click to expand...
Click to collapse
Try to re-install Samsung drivers and see if your data cable is broken or try a different one
kumayam said:
Try to re-install Samsung drivers and see if your data cable is broken or try a different one
Click to expand...
Click to collapse
Some reason Odin crashes while initializing to begin the process. :/
EDIT: Tried multiple cables, ports and reinstalled drivers btw.
UnboundGodz said:
Some reason Odin crashes while initializing to begin the process. :/
Click to expand...
Click to collapse
Have u tried a different Odin? I'm using princecomsey version
kumayam said:
Have u tried a different Odin? I'm using princecomsey version
Click to expand...
Click to collapse
I havent, but I am now. Also ran as Admin if it helps. Will edit when I know more.
EDIT: Appears I just am not getting lucky here. Unsure as to why this is happening, is there anything on my device I should enable/disable for this process?
---------- Post added at 04:20 AM ---------- Previous post was at 04:13 AM ----------
kumayam said:
Have u tried a different Odin? I'm using princecomsey version
Click to expand...
Click to collapse
Updated prior message, appreciate the help!
At&t just released pie for the s8+.
Sent from my SM-G955U using Tapatalk
Question about future Ota updates
I followed your guide successfully, will I continue to receive Ota updates as usual as they are released in the future?
Working good on Verizon ?
---------- Post added at 09:18 AM ---------- Previous post was at 09:17 AM ----------
Yes, but if you're like me you'll end up installing it before the OTA goes out ever again
OK guys its out for ATT right now. Go Get it.
solitarios.lupus said:
OK guys its out for ATT right now. Go Get it.
Click to expand...
Click to collapse
where i can find the 9.0 for pie
daviddiazayuso said:
where i can find the 9.0 for pie
Click to expand...
Click to collapse
I got it by, forcing an Ota update (had to disable my VPN) att site has not updated yet.

Categories

Resources