I can not enter the boot loader! - Omnia 7 General

Hi,
I Aasttia for access to the download status??
After reading about some of the solutions I learned that the issue Pot Lauder is not required so I can get into this situation.
OS ver.7.0.7390.0.
Firmware rev. num. :2424.10.10.6
HW rev. num. 3.15.0.4
Radio soft. ver. 2424.10.10.6
Radio hw. ver. 0.0.0.800
Bootloader ver. 4.10.1.9
Chip SoC 0.36.2.0
--------------------------------------------------------------------
Forgive me for my English, I spoke except by divorce

If you really need to get into download mode on 4.10.1.9 you need to use a usb jig / home made resistor jig.
the guide is here http://forum.xda-developers.com/showthread.php?t=1092824
However people have said that they have updated to 7392 ok without being able to enter download mode.

Thanks for your response.
'm Going to try this method

It worked fine for me and I was able to apply the Samsung patch that was released some time ago

Related

Newbie Here seeking guidance

Just obtained from ebay T-Mobile PPC Rom Ver: 3.08.10 ENG, Rom Date: 07/11/02, Radio Ver: 6.02, Protocal Ver: 324e4, CPU: ARMSA11110, Model: PW10B1, came with no sim card. Looking to unlock, which would best to use from here. Also how do it find what Bootloader version is on it and where or not the PPC2002 version I have is modem capiable? :lol: :roll:
to unlock, download the xda unlock tool from www.xda-developers.com/XDAunlock/ and run it on your xda.
the modem s/w is named wmodem.exe and you should find its link under programs.
good luck ...
opps! ... you can get the boorloader screen by pressing soft reset while pressing and holding the power button.
XDAunlock .exe
Ran this and got the following: error getting unlock code. What would cause this? :roll:
Could this be that this does not have a modem.
Or maybe this is the problem:
To Find Your Current ROM Version:
Select Start -> Settings -> System and choose the Device Information icon.
If your device is running 3.08.10, you should upgrade.
A full list of benefits of the upgrade is contained in the release notes.
Pocket PC Phone Edition Download Center:
To download the current upgrade software (15.9MB), please enter your 10 digit valid T-Mobile phone number:

Unsuccessful Omnia 7 updates to 7392 only! (Using samsung latest tool or Zune. )

(If Looking for " USB-JIG for Samsung OMNIA 7 - Correct instructions! Quick and very SIMPLE guide ". Go Here....)
There are few update threads but this one is for unsuccessful updates only.
Please post your phone details and your NODO update method.
A - "Walsh method"
B - "Hungarian IP no data 15 sec. hack "
C - Regular Zune update.
Note: if you are looking for " USB-JIG for Samsung OMNIA 7 - Correct instructions! Quick and very SIMPLE guide " , go Here....
_____
My case:
Not branded - Samsung Omnia 7 updated with NODO using method B. ("Hungarian IP no data 15 sec. hack ")
Never rooted or used any unlocking tools.
OS ver.7.0.7390.0.
Firmware rev. num. :2424.10.10.6
HW rev. num. 3.15.0.4
Radio soft. ver. 2424.10.10.6
Radio hw. ver. 0.0.0.800
Bootloader ver. 4.10.1.9
Chip SoC 0.36.2.0
Cant get the phone in Download mode.
To get your Omnia7 into Download mode:
Phone off and:
- Press and hold the Camera button;
- Press and hold the Volume DOWN button;
- Press and hold the Power button;
- Release the power button when you see white Samsung Omnia7 Logo on your screen.
You should have entered Omnia7 download mode.
Remark: On lots of places you will find out that "VOLUME UP" is correct button but this is not the case with my SO7.
1. I tried using Samsung Omnia 7 Update tool. or go to MS Windows Omnia 7 page .
After trying for more than 1 hour I could not enter into boot loader mode.
(There is a message on the bottom of the Samsung tool to contact service support if I can’t enter the bootloader mode)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2. Zune reported that update is available.
- On the PC: I started the update but process stuck on “rebooting the phone” page. ( page 6 of 10 )
- On the phone: rebooting process stuck on “Samsung Omnia 7” white color msg.
Waited for 20 minutes and then
- Disconnect the USB cable,
- Pressed and hold the power button for minimum 5 sec for a phone restart.
- After the Windows Phone screen loaded ( BIG HUH!) I reconnected the usb cable.
- Phone was detected by Zune and the following message appeared.
- The update zune error code is because I have to disconnect the USB cable – reboot and connect again.
- If using Samsung update tool – Cant get the phone in DL mode.
- Bootloader ver. 4.10.1.9 (see first post)
This will be ugly.
Repeated everything 3 times.
Let the headache begin !
KraFT
UPDATE:
If you have 4.10.1.9 that does not mean that you will have problems updating. Most of the affected are devices with that version. Do not assume that your update wont work if you have that version.( Or any other.)
- At this point nothing is fixed. Hardly they will fix anything at this point.
So:
- Your update might work without any problems.
- Your update might work without any problems after you used the Samsung update tool.
- Your update might NOT WORK AT ALL as described in the first post.
UPDATE: If you want to try and update with USB-JIG I created this simple guide here.
Just to clarify:
A. To get your Omnia7 into Download mode:
Phone off and:
- Press and hold the Camera button;
- Press and hold the Volume DOWN button;
- Press and hold the Power button;
- Release the power button when you see white Samsung Omnia7 Logo on your screen.
You have entered Omnia7 download mode.
Note:
On lots of places you will find out that "VOLUME UP" is correct button but this is not the case with my SO7.
B. To get your Omnia7 into "USB ---to----> PC" mode.
Phone off and:
- Press and hold the Camera button;
- Press and hold the Power button;
- Release the power button when you see white Samsung Omnia7 Logo on your screen.
You have entered with your Omnia7 into "USB ---to----> PC" mode.
KraFT
Looks like you got the Samsung error code. Try the following steps in the attached link; should help you out
http://wmpoweruser.com/samsung-releases-801812c1-update-error-fix-for-the-samsung-omnia-7/
what is your bootloader version?
Its neither of that.
- If using update from Zune - the phone cant reboot on page 6 of 10.
- The update zune error code is because I have to disconnect the USB cable – reboot and connect again.
- If using Samsung update tool – Cant get the phone in DL mode.
- Bootloader ver. 4.10.1.9 (see first post)
This will be ugly.
K
Bootloader ver. 4.10.1.9. Same problem. Used option B to update to Nodo. Tried using Samsung Tool but download mode wont come up.
Called Samsung service centre as per advise on the Samsung Update tool but they told me nothing they can do and to call Microsoft. Meh!
Unable to update even after using Samsung Tool. Phone keeps rebooting at Samsung Omnia 7 logo.
OS Version: 7.0.7390.0
Firmware revision number: 2424.10.11.1
Hardware revision number: 3.15.0.4
Radio software revision: 2424.10.11.1
Radio hardware version: 0.0.0.800
Bootloader version: 4.11.0.3
Chip SOC version: 0.36.2.0
Try this guide
http://windowsteamblog.com/windows_...spx?utm_source=twitterfeed&utm_medium=twitter
Tony.Montana. said:
Try this guide
http://windowsteamblog.com/windows_...spx?utm_source=twitterfeed&utm_medium=twitter
Click to expand...
Click to collapse
I came from there. Doesn't work for me. Samsung still having issues...
sorry about that...It worked for me
wow... just wow....
I have said 4.10.1.9 bootloader version. I did nothing wrong, i updated my phone when prompted by official means and MS response is to call samsung support?
That is frankly not on. I am really angry about this, I have been such a strong supporter of MS and their products. I have Windows on my PC, I've had both XBox console and had windows mobile and now windows phone. I feel so let down by this, what a load of crap.
VoodooKing said:
Unable to update even after using Samsung Tool. Phone keeps rebooting at Samsung Omnia 7 logo.
OS Version: 7.0.7390.0
Firmware revision number: 2424.10.11.1
Hardware revision number: 3.15.0.4
Radio software revision: 2424.10.11.1
Radio hardware version: 0.0.0.800
Bootloader version: 4.11.0.3
Chip SOC version: 0.36.2.0
Click to expand...
Click to collapse
Same bootloader, successfully updated from 7008 only with zune
I have bootloader 4.10.1.9, and I managed to update my phone by putting the phone in download mode using the trick as described in this video: http://youtu.be/D0aoabVtPJ8
As an alternative, you could use a usb jig, the same ones that can be used for Samsung Galaxy S.
By putting the phone in download mode, you can install the Samsung patch. After that I had no problems installing the 7392 update through the Zune client.
Omnia 7 8Gb unlocked from factory.
My configuration was:
OS Version: 7.0.7008.0 (updated from 7004 removing the mobileOperator ID into the registry)
Firmware revision number: 2424.10.10.6
Hardware revision number: 3.15.0.4
Radio software revision: 2424.10.10.6
Radio hardware version: 0.0.0.800
Bootloader version: 4.10.1.9
Chip SOC version: 0.36.2.0
I did the trick of hungarian vpn to update to 7390, but in one week I restored to 7008 version again due to warning of Microsoft about unofficial updates.
Now I have 7.0.7392.0 using Zune normal update. No problems at all updating.
Very happy after long waiting.
I have bootloader version 4.10.1.9 and I updated from NoDo to 4392 using Zune. Did not need to use the Samsung tool. My phone is a T-Mobile UK unlocked.
Successfully updated from 7008 to 7392 only with Zune, all steps went fine.
My configuration now:
Samsung Omnia 7 16GB unbranded from Germany
OS Version: 7.0.7392.0 (before it was 7008)
Firmware revision number: 2424.10.11.1
Hardware revision number: 3.15.0.4
Radio software revision: 2424.10.11.1
Radio hardware version: 0.0.0.800
Bootloader version: 4.11.0.3
Chip SOC version: 0.36.2.0
The same problem here, unbranded Omnia 7
Updated to NODO with the wifi trick.
Bootloader version: 4.10.1.9
Can't get the phone in Download Mode.
Samsung...never again, the last phone from this OEM I buy.
And another:
Unbranded Omnia 7
Updated to NoDo with the 'pull network cable after 3 seconds' trick.
Bootloader version: 4.10.1.9
Can't get the phone in Download Mode.
Last thing to try is the trick with the 3 resitors and the USB port to get it into download mode (first need to find me the 100 ohm resistors)
Also considering not to buy another Samsung... but I do like the display!
Hello,
I have a debranded omnia 7
botloader: 4.10.1.5
firmware pda: JJ5
firmware phone: JJ3
nodo update throught zune desconect method
yesterday i try to update from nodo to 7392 and its imposible. allways stop in steep 6, during the reboot of the phone.
I apply samsung patch and the i can update to 7392 in the first atemp.
Unsuccessful after patch
I used the Samsung tool before even trying the 7392 update from 7390. After that, I tried updating but I'm getting the endless boot loop. I don't even know if it would have worked without the patch. I'm debating whether I should call Samsung up and see what solutions they've got for me, but I'm not sending my phone in if that's what they'll request! -.-
Samsung response
They suck! They said to contact Microsoft because it has nothing to do with them since the phone isn't able to connect with the Zune software or something..... I don't think she understood that it all works fine and dandy up until the phone needs to reboot and it just loops over and over again without even getting to the update screen... -.- Which, to me sounds like it's their problem since they need to be able to get the phone to boot up into the update mode screen (whatever the name for it is again...).
I never intended to have anything to do with Samsung because I knew how I hated their phones and designs (although the Omnia 7 is exempt from the design statement) but that's the only Windows Phone that Three UK offered!! :/

[Q] Omnia 7 updating - Where to start?

Hi. This will most definitely sound noob, but I have to ask in order to upgrade my omnia 7 8GB:
I bought my Omnia 7 a week ago, in Serbia and it is (apparently) "taken" from the Hungarian T Mobile (the logo screen is there) but it is carrier unlocked because I can put any SIM card and it works. At first there were problems like not displaying the sms and e-mail messages, and when I changed the "System locale" language and stuff it couldn't connect to the internet via Internet Explorer (I left it to Hungarian, so now it does). i also did the "Reset your phone" option in the settings -> about menu and the SMS and E-mails are now fine, BUT, I don't understand how to wake up the phone when it's on standby because sometimes the only way to wake it is by pressing the power button (at first I thought the WINDOWS button was non-responsive, but I was wrong). I even tried the download screen and hard reset screen (combo of keys) and while the Download mode is O.K. (I guess 'cos it displays the triangle screen) the Hard REST SCREEN seems to be faulty because it lasts only for a half a second and then the phone restarts without even letting me choose whether to reset or not?!?!
I still haven't even connected it to Zune. I've downloaded the MS Windos Phone Dev tools (the 400 MB package) on Windows 7, but waht to do next.
I also don't understand entirely what is 'firmware', what is 'ROM' (i know in other devices that the firmware is something like BIOS, but ROM can also be some oprating system, right?) and 'CSC (I know it has to do with the country selection) and which update contains what, and so on> I mean I've read the forums and I know what is to developer-unlock and carrier-unlock (sorta), and I'm getting along with OSes since the ZX Spectrum's basic - upto Ipad's iOS4, but I don't know what to do. I want to developer unlock it, to update to NoDo, or even Mango, and to try to sideload homebrew apps WITHOUT relocking and WITHOUT BRanding it (or carriel-lock it). Because the firmware and all are pretty old, what should I do first: flash the phone, or update via Zune or do the Chevron or something else 'cos I'm afraid if it can't be upgraded or if there may be some issues. PLEASE HELP and sorry 2 bother U guys
Thanx in advance
My firmware and everything is pretty old from what I've seen so far:
OS version: 7.0.7004.0
Firmware revision number: 2424.10.10.4
Hardware revision number: 3.15.0.4
Radio software version: 2424.10.10.3
Radio hardware version: 0.0.0.800
Bootloader version: 4.10.1.2 (this is pretty old, right?)
Chip SOC version: 0.36.2.0
and the Diagnosis data:
Diagnosis (ver.0929)
PDA: I8700XXJJ4
Phone: I8700XXJJ3
CSC: I8700TMHJJ4 (NOTE: the TMH isn't mentioned anywhere on the web but I think it's TMobile HU)
Bluetooth S/W: 0.01
Bluetooth H/W: 0.01
Bluetooth MAC: bla bla bla
Wi-Fi S/W: 1.0
Wi-Fi H/W: 1.0
Wi-Fi MAC: bla bla bla
O.K. So I couldn't wait and unlocked the phone with Chevron. It worked O.K. and Zune installed the update 7008. After that I even deployed a .xap (it worked ). When I tried to deploy again it started O.K. but then it said something like "The port to comunicate is not a socket" or smt like that. Then, I noticed that Zune warned me that another update was ready (the 7392) and started and went well until the last step when it said "update fail, error code 801812dd". I googled and found that that may be because of the USB cable / port (I have the original cable). So I connected the phone to a USB port at the back of my PC, but Zune doesn't recognise any updateds any more? What should I do? Thanx in advance
Well, I figured it out. I DID IT, I installed the 7392 update. It works like a charm. It even updated my bootloader and what not. Thanx guys, you're awesome, but mostly thank to those who tried to explain the stuff in a more simple manner, for us, the beginners.
My new stats:
OS version: 7.0.7392.0
Firmware revision number: 2424.11.2.3
Hardware revision number: 3.15.0.4
Radio software version: 2424.11.2.2
Radio hardware version: 0.0.0.800
Bootloader version: 5.2.1.4
Chip SOC version: 0.36.2.0
and the Diagnosis data:
Diagnosis (ver.0929)
PDA: I8700XXKB3
Phone: I8700XXKB2
CSC: I8700TMHKB3 (NOTE: the TMH isn't mentioned anywhere on the web but I think it's TMobile HU)
Bluetooth S/W: 0.01
Bluetooth H/W: 0.01
Bluetooth MAC: bla bla bla
Wi-Fi S/W: 1.0
Wi-Fi H/W: 1.0
Wi-Fi MAC: bla bla bla

[Q] 80180048 error when updating to 7740

Hello,
I got the infamous 80180048 error when I update to 7740 on my Samsung Focus.
Infos:
OS : 7.10.7720.68
FW : 2124.11.9.4
HW : 3.1.0.7
Radio Soft : 2124.11.9.4
Radio HW : 0.0.0.2
Bootloader : 5.9.2.2
Chip SOC : 0.36.2.0
I tried the WP Support tool but I got "The phone is not in the 'Connect to PC' state." even if I have indeed the image, killed Zune and see phone in USB device.
Any idea ?
i have the sam Problem, any idea ?
I end up flashing the original ROM and doing all the updates up to 7740.16.
The program to use and instructions are here
http://forum.xda-developers.com/showthread.php?t=973420
the ROM's for several companies are here
http://forum.xda-developers.com/showthread.php?t=1131891
I tried this before, and it messed up my ability to connect to the network on Rogers. After using it, my phone wouldn't connect to 3g and barely connected to any other type of network...
Think i just got a bad ROM? it was a rogers ROM
Did you try with the official retail one from this post:
http://forum.xda-developers.com/showthread.php?t=1131022

[Q] Help needed for focus rev 1.4 [Solved]

Hi everyone,
I just received at&t unlocked focus having rev 1.4 . I am not using this phone with at&t sim.
I am facing too many problems:
1. GPS is not working. GPSInfo says that location service is disabled, though it's enabled in settings. When I tried with samsung diagnosis app (##634## then *#1472365#), it says "location service is not supported on this device".
2.
A] Device is not updating to mango. Zune recognizes the device only when it's connected to computer and rebooted. After that zune works fine but when I try to update, I get error 800705b4 and sometimes 800706be.
B] Tried phone support tool but it says that device is not in "connect to pc" mode.
C] When tried manually updating via cab files using updatew.exe, it doesn't work.
Is there any way of updating it to mango? Also can just gps be fixed somehow?
Device details:
Samsung focus i917 rev 1.4 at&t
OS version: 7.0.7392.0
Firmware: 2103.11.4.1
Hardware: 3.1.0.7
Radio software: 2103.11.4.1
Radio hardware: 0.0.0.4
Bootloader: 5.4.2.1
Chip SOC: 0.36.2.0
Solution found:
I flashed Samsung i917 Focus firmware UCJK3 ATT USA 4K available in one of the threads and then zune updated it to mango 7720 in about 2 hrs. Now everything is working properly. Thanks to all those who took time to view my post.
I sensed something wrong with you PC.
Maybe you should reset your phone, and dial ##634# and enter *#7284#, switch to ZUNE SYNC.

Categories

Resources