[Q] Repairing (the keypad of) a HD2 - HD2 General

After replacing the main board of my HD2, the keypad no longer works. At first the button on the left (answer phone) was still working while the other weren't but after reseating the flex cable of the keypad, none of the keys work.
I don't think the main board (or the connector) is broken but I will be able to test that soon enough since I ordered a replacement keypad board. I will be able to just plug that one in without having to disassemble the HD2 to check if it's indeed the keypad that's broken.
But if the keypad is indeed broken, I will need to replace it (obviously). I can find how to disassemble the HD2 (video's, pictorials, etc), but nowhere can I find how to assemble the HD2.
For instance, you will need to separate the screen from the chassis by heating it up (with a heatgun or blow dryer) since those are glued/taped together. But I can't find anywhere how to glue/tape those two parts together again.
So can anyone direct me to some instructions? Or have any tips?

(Shameless) Bump?

Related

[Q] HTC HD2 [TMo] LCD Ribbon or Socket Broken

So here is my story. I installed a new digitizer for my broken HD2 screen, and ended up creating a crease on the ribbon cable. I managed to also break off half of the lock-in bar (the black bar) on the socket, but it still locks half of the other pins down and in place.
Heres the problem.
I turn on the phone, and the screen lights up but doesn't show me my display. The backlight IS on, but isn't showing the bootup, or anything. I DID manage to get it to show the screen by messing with the cable, but only for a few seconds and then it wouldn't anymore. The phone functions fine, I had a friend send me a text and the phone vibrated, and when I pressed the lock button it locked and unlocked (for my Android ROM). I know it did this because the backlight would turn on and off on the LCD.
Would buying a new LCD fix the problem or does that little black bar on the socket matter? I figured all it did was lock the pins in place so it shouldn't be a big deal..
there is 3 ways out of that.
One put a tape over the back side of the flex. it might work sometimes, but not reliable
Two buy a new socket from ebay and resolder it.
Three hardcorely wire them. It is possible I fixed a broken volume flex before.
the lock does not just hold the cable in place it also pushes it down on the contact face.
You may be able to pack the ribbon on the back to help it fit tighter in the sock & increase pressure to the mating faces, hopefully the rest of cable is serviceable ! extra lock security can be added with tape & ribbon can be reinforced with tape too if helps.

Damaged HD2 before even using :(

So i bought a used HD2 so i could get rid of my Aria and do a dual boot
The digitizer was bad so i bought that as well as a new screen, replacing it the main flex ribbon that connects to volume port broke which is unrepairable and the pcb where the flex connects to the socket lid broke half way when removing the tape so dang fragile.
But the ribbon still goes in and it still closes, so the main issue is the flex ribbon with the broken volume button.
So my tech is an idiot. But i really want to use the HD2. Is there somebody that has those parts and can fix it?
I already spent $65 on the digi and screen so i feel
Yes go onto ebay and look for hd2 side volume key pcb.
It's a lengthy repair but nothing too difficult if you like electronics.
http://www.ebay.com/itm/New-OEM-HTC...ultDomain_0&hash=item1c21fcc331#ht_1766wt_964
found it, should have some fun now

HTC HD2 assembly problem

Hi guys,
I just disassembled my HD2 to replace my broken digitizer and touchscreen.
But now i'm stuck with a problem.
What shall I use to glue both items together again?
And the keyboard makes some issues.
I tried to place both parts over eachother to see if they fit but I can't press the keys after it.
Seems like they are stuck.
That's why I didn't want to use superglue because after assembling it I wouldn't be able to change anything.
Maybe pictures tell more than words.
http://www.youtube.com/watch?v=t8Q7mXdcJ54&feature=player_embedded
hope that helps you
thanks wasn't the information I was looking for but nevermind
I assembled the device now .. but the next problem occured ..
the hd2 is loading without problems (led shows it) but when I try to power it on it's completely dead. nothing happends
with my old touchscreen it was at least possible to power it on.
my question is:
could the new soldered touchscreen + digitizer be broken? or did I break something during disassembly and assembly?
To be honest I didn't see any mistakes I made.
It's not my first time repairing stuff like that because I used to repair notebooks as a hobby.
Still i'm unsure what the heck is going on with my phone atm.
did you check if the flex cable from display is in the port, there is an white stripe that shows how far it must in the port. Did the phone vibrate when you pressed power button?
I checked the cables and found nothing suspicious.
and the phone didnt even vibrate after trying to power it on.
I'm trying to get a new hardkey board (i hope you know what I mean).
Had problems with the keys being stuck and maybe I killed that one by trying to assemble it.
if the phone doesn't recognize me pushing the power on key it's no wonder it won't do anything.
hope this will fix the problem
12dollar said:
I checked the cables and found nothing suspicious.
and the phone didnt even vibrate after trying to power it on.
I'm trying to get a new hardkey board (i hope you know what I mean).
Had problems with the keys being stuck and maybe I killed that one by trying to assemble it.
if the phone doesn't recognize me pushing the power on key it's no wonder it won't do anything.
hope this will fix the problem
Click to expand...
Click to collapse
Most likely something is wrong with your Power button, but you should turn it on with 2nd method:
- pull out battery;
- insert usb cable(connected to PC)/charger in your usb port;
- insert battery.
This way it should turn on whatever OS you have installed on.
If your OS is Android through MAGLDR, connecting it through usb should turn it on by default, unless your battery is not dead!
Check it out!
bib*oops said:
Most likely something is wrong with your Power button, but you should turn it on with 2nd method:
- pull out battery;
- insert usb cable(connected to PC)/charger in your usb port;
- insert battery.
This way it should turn on whatever OS you have installed on.
If your OS is Android through MAGLDR, connecting it through usb should turn it on by default, unless your battery is not dead!
Check it out!
Click to expand...
Click to collapse
I just did as you said and yeah the phone came to life.
so there is definately a dead power button (probably the board is broken)
12dollar said:
I just did as you said and yeah the phone came to life.
so there is definately a dead power button (probably the board is broken)
Click to expand...
Click to collapse
Glad to hear that!
Definitely you should replace your keypad flex!
Did you fix the problem with the hardware keys
Hi,
I have very similar problem.
I changed the touch screen on my HD2 and after reassembling I cannot get the hardware keys clicked.
I ordered a brand new key board and brand new plastic buttons. I received them but situation is the same.
If somebody can explain is there any trick during adjusting the plastic buttons to the clickable "small dots" on the board - please help me.
Best Regards
maznevh said:
Hi,
I have very similar problem.
I changed the touch screen on my HD2 and after reassembling I cannot get the hardware keys clicked.
I ordered a brand new key board and brand new plastic buttons. I received them but situation is the same.
If somebody can explain is there any trick during adjusting the plastic buttons to the clickable "small dots" on the board - please help me.
Best Regards
Click to expand...
Click to collapse
Normally this is always down to glass digitizer not being aligned correctly when stuck to LCD.
0.05mm can make all the difference here.
You need review current digitizer position & pre test assembly to centre chassis without tape for a test run on button function.
Also check button board position is exact & located correctly in the pin holes at each end of the board.
original board quality is normally far better than most of the very cheap eBay pattern parts but one or two sellers offer a decent board around $4.50
Also clean all old tape from back of LCD & centre chassis plate so parts fit flush & once all checked new tape can be added, I also use small spots of up40 adhesive sealant near corners & near middle edges for final build up as holds far better than even the best tapes & gives an original strength & long lasting flush look to final job plus us easily removed with razor blade if repair ever needed again.
Super glue is a BIG no no NO.
Hard to get hardware buttons clickable
Mister B said:
Normally this is always down to glass digitizer not being aligned correctly when stuck to LCD.
0.05mm can make all the difference here.
You need review current digitizer position & pre test assembly to centre chassis without tape for a test run on button function.
Also check button board position is exact & located correctly in the pin holes at each end of the board.
original board quality is normally far better than most of the very cheap eBay pattern parts but one or two sellers offer a decent board around $4.50
Also clean all old tape from back of LCD & centre chassis plate so parts fit flush & once all checked new tape can be added, I also use small spots of up40 adhesive sealant near corners & near middle edges for final build up as holds far better than even the best tapes & gives an original strength & long lasting flush look to final job plus us easily removed with razor blade if repair ever needed again.
Super glue is a BIG no no NO.
Click to expand...
Click to collapse
It is not the case in my case , because I ordered full set (digitizer + display) and they arrived factory assembled.
But you are definitely right - 0.05 mm make the difference. I think the problem comes from the fact that the board with buttons cannot be firmly fixed to the 2 small juts on the chassis. You know the plug of the buttons board is on the tail like extension. Probably when I try to cover the buttons board with the LCD+digitizer - the frame of the LCD slightly pushes the buttons board and the juts on the plastic buttons cannot be fixed exactly on the top of the actual buttons on the board. Anyway we are speaking about precise fixing something around 0.05 mm over something else, which is exactly same size... and in the same time you have to fix this without any visibility.
I will continue trying. If you can give me any other ideas - I will appreciate this.
Thanks
maznevh said:
It is not the case in my case , because I ordered full set (digitizer + display) and they arrived factory assembled.
But you are definitely right - 0.05 mm make the difference. I think the problem comes from the fact that the board with buttons cannot be firmly fixed to the 2 small juts on the chassis. You know the plug of the buttons board is on the tail like extension. Probably when I try to cover the buttons board with the LCD+digitizer - the frame of the LCD slightly pushes the buttons board and the juts on the plastic buttons cannot be fixed exactly on the top of the actual buttons on the board. Anyway we are speaking about precise fixing something around 0.05 mm over something else, which is exactly same size... and in the same time you have to fix this without any visibility.
I will continue trying. If you can give me any other ideas - I will appreciate this.
Thanks
Click to expand...
Click to collapse
Do not rule out the LCD/Digitizer assembly as the china combos are prone to not the best accuracy of assembly as sounds like maybe LCD is mounted just a fraction too low on the digitizer perhaps.
Button board should be fixed via 3M style tape & most replacement boards come with tape ready for fitting.
worth making effort with button board to centre chassis to mount securely then mounting lcd to chassis without tape for a trial assembly & try and check for possible issues such as bent chassis or old tape not removed sufficiently or new assembly alignment not the best.
I would also recommend using original plastic button strip as the copy ones are not always good & have had experience with them before.

HD2 screen and input jack problems.

Hello,
Where can I find a good replacement for HD2 digitizer?
I have Windows Phone 7.8 on it (I had the same problem on Android) and sometimes when I am using it, the digitizer registers my touches wrong.
Seems to be the left side is most affected by this - Like when I press e, it presses q also, or w then q too. Also happens with s (a) and symbols. Cannot even pinch to zoom.
This has rendered my HD2 a unpractical phone. It started randomly last summer.
Should I change the digitizer in this case or is there something I can try?
Also, my input jack is messed up - when I have a headphone connected to it and the plug shakes in the slightest - The phone things I want to pause the song or play it. Also activates the voice search which is a freaking PAIN.
Can anyone please help me and tell me what I should do about these issues?
Digitizer & other parts such as assembly tape can be found on eBay.
Dosome homework on digitizers & stripdown guide to save yourself from common problems/mistakes.
Audio plug maybe harder issue to rectify, it can be replaced but requires a good solderer to do good job. You may improve things by cleaning socket & cable plug & trying to improve contact spring arms tension position in socket with a pin or similar.
Mister B said:
Digitizer & other parts such as assembly tape can be found on eBay.
Dosome homework on digitizers & stripdown guide to save yourself from common problems/mistakes.
Audio plug maybe harder issue to rectify, it can be replaced but requires a good solderer to do good job. You may improve things by cleaning socket & cable plug & trying to improve contact spring arms tension position in socket with a pin or similar.
Click to expand...
Click to collapse
But does this issue seem related to digitizer being faulty or just a cable a bit damaged? Sometimes the issue appears and sometimes it doesn't.
Ribbon on digitizer is all one piece & any permanent repair usually is only really achieved by replacement of digitizer.
I have had similar issues of screen presses activating other area on screen & dead zones on digitizer error & also the more common no touch issue, all required digitizer to fix .
Anyone know where to find a replacement jack in the USA??
Sent from my HTC One X using xda app-developers app

[Q] HTC HD2 Black screen after falling

My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
any body ????
muhama said:
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
Click to expand...
Click to collapse
any body ????
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Mister B said:
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Click to expand...
Click to collapse
Thanks for reply me:good:
How can i open my phone? And where is connector located?
Do you have a link to view that?
Have a read of this thread for start
http://forum.xda-developers.com/showthread.php?t=1566179
Plenty more if do a search
Basically be very very careful, use plastic pry tool ONLY to remove back, start at top. 2 clips about 7mm in from top edges then once released work down right side, DO NOT stick any tools in near the volume key, if doing it right the back comes of very easy (2 pry tools are better as can keep one in top sstopping it clipping back in)
Once back off handle with care, rough handling breaks th spring contacts for antenna etc.
LCD from mainboad can be disconnected from mainboard without fully removing flex & is absolute best way do it.
I did write few posts on it so will try dig them up & link you.
If buy lcd/gigi assemble also buy a button board ribbon as they like only $3USD, with spare button ribbon you can easily plug new lcd/digi in & plug new button board ribbon into mainboard & hold a battery on it to do a test befoe sticking things together.
Also you likely damage ribbon if not careful so spare likely get used on rebuild.
Parts link is in HD2 Wiki
http://forum.xda-developers.com/wiki/HTC_HD2#Fixes.2C_Hints_.26_Tips

Categories

Resources