Ok I'm trying to install NAND Android on my HD2 & have found a thread that I can follow but to get started I need to have SPL 1.42.0000, 1.62.0000, 1.66.0000, 2.07.0000, 2.08.0000 or 2.10.0000 installed & I had 3.03 having just debranded the phone using HSPL.
Now I know I have to use bootloader to downgrade which I have managed to do but now have "Not Allowed" come up on the screen, the phone just goes into tri colour & now shows SPL 1.42.0000.
I think I know the reason - this was a stock rom I downloaded from the HTC site & my phone is a TMobile UK so presumably I would need an SPL as above for the TMobile network to strat with? If so where can I get one from as HTC don't appear to have one on their site with the SPL numbers as above?
Many thanks
Junks
spls are not specific to any network.
run hspl4 choose 2.08.hspl, done.
samsamuel said:
spls are not specific to any network.
run hspl4 choose 2.08.hspl, done.
Click to expand...
Click to collapse
Thanks Sam - Didn't realise that, I still have to get the phone to start though as I can't now get a connection to the PC as its stuck in tri colour mode with no USB
Plug in the cable, when "serial" becomes "USB" at bottom of bootloader screen, you're good to go. Forget you ever heard of an "activesync connection",,, it doesn't mean the activesync program, it means " USB connection"( using the activesync drivers)
Thanks again Sam, sorted that now & got HSPL4 loaded.
Need to put up another post now as stuck on the MAGLDR screen & cant get the NAND DAF to load!! I shouldn't have started this!
Junks666 said:
Thanks again Sam, sorted that now & got HSPL4 loaded.
Need to put up another post now as stuck on the MAGLDR screen & cant get the NAND DAF to load!! I shouldn't have started this!
Click to expand...
Click to collapse
Use Clock Work Mode Recovery to flash your NAND Android ROM. Check my sig for a link to CWM. With CWM all you have to do is copy the .zip.file to your SD card and then use CWM to flash it. It is very easy this way. The thread on CWM will tell you how to flash it and all info need to know about it.
Thanks for that but I've only just managed to do the simpler method wrong & don't understand the CWM at all at the moment. Was just trying to get the easiest route for my first flash but after trying three NAND ROM's I get the same error after loading MAGLDR & running the DAF.exe
As MAGLDR is loading...........SS SD kernel open failed
Then after running the DAF.exe files
Happen error
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: file not exist
Info: .\RSPL\RSPL.cpp (346)
Did you get it going Junks?
Don't panic, we can fix this
T-Macgnolia said:
With CWM all you have to do is copy the .zip.file to your SD card and then use CWM to flash it. It is very easy this way. The thread on CWM will tell you how to flash it and all info need to know about it.
Click to expand...
Click to collapse
Junks666 said:
Was just trying to get the easiest route for my first flash
Click to expand...
Click to collapse
Go read the thread on CWM!!! As I said you just copy the .zip file of the ROM to your SFD card wich is how you download the ROM meaning you have to only download it nothing else. To copy it to your SD card use USB MassStg option #4 of MAGLDR but you have to have your phone connected to your computer via USB cable. To flash CWM connect your HD2 via USB and select the USB Flasher option #5 of MAGLDR then run the DAF of CWM. This will flash CWM to yor HD2. when your phone reboots keep the power button pressed down to get MAGLDR back up then select AD Recovery option #8 of MAGLDR. This will bring up CWM, then select "install zip from sdcard" then select "choos zip from sdcard" then find the .zip file that you just copied to your SD card and select it and it will flash the ROM. Oh yeah you have to use the send button to select each thing. Now what else do you not understand?
Look at my signature for links to MAGLDR and CWM.
Not yet Mez
Well I thought that seemed easy to understand TMac but.................
I intalled the cleandroid zip file but I guess since it didn't work you meant extract to the SD card (CWM didnt find the cleandroid zip file)? Also is there anyway of booting normally at the moment as I think I should charge the battery again after all this trying without success before I try again?
Thanks for your patience, I'm really not used to this sort of thing at all & at 54 yrs old I think I'm doing quite well!! lol
Junks666 said:
Not yet Mez
Well I thought that seemed easy to understand TMac but.................
I intalled the cleandroid zip file but I guess since it didn't work you meant extract to the SD card (CWM didnt find the cleandroid zip file)? Also is there anyway of booting normally at the moment as I think I should charge the battery again after all this trying without success before I try again?
Thanks for your patience, I'm really not used to this sort of thing at all & at 54 yrs old I think I'm doing quite well!! lol
Click to expand...
Click to collapse
Clean droid is also my fav rom
Assuming that you are able to boot into MAGLDR screen and you have the Cleandroid rom in your PC.
Now, in MAGLDR screen, select menu no.5 (USB Flasher) and subsequently connect your phone ( Plug UsB to PC). On your PC, run the DAF.exe of Cleandroid rom.
If you succeed, it will reboot to android.
Before doing that, please make sure battery above 50 %, spl 2.08 HSPL and radio 2.15.xx were installed.
Good luck
silverwind said:
Clean droid is also my fav rom
Assuming that you are able to boot into MAGLDR screen and you have the Cleandroid rom in your PC.
Now, in MAGLDR screen, select menu no.5 (USB Flasher) and subsequently connect your phone ( Plug UsB to PC). On your PC, run the DAF.exe of Cleandroid rom.
If you succeed, it will reboot to android.
Before doing that, please make sure battery above 50 %, spl 2.08 HSPL and radio 2.15.xx were installed.
Good luck
Click to expand...
Click to collapse
Thanks but tried that as posted earlier & get the happen error, now I'm not sure of the battery charge so want to charge that before trying again with CWM but can't charge it from the MAGLDR screen, tried plugging into the mains & reset but what ever I do it boots into MAGLDR & no charge
Yes MAGLDR makes your phone do that. Have you been able to flash a ROM yet no? Are you making sure your going to the 'USB Flasher' in MAGLDR? Run the daf when you're there, if you're getting that error still, make sure you disable USB connections inside of ActiveSync or WMDC on Vista/7.
Sent from my HTC Vision using XDA App
Thanks I'll try that next then - any ideas on getting the battery charged up again now though?
Junks666 said:
Thanks I'll try that next then - any ideas on getting the battery charged up again now though?
Click to expand...
Click to collapse
I would suggest you to reflash winmo from boot loader screen using micro sd in order to be able to charge battery. After that, you can retry the android flashing
Thanks - sorry if I'm a bit thick here, so does that mean I've put the phone back to original then start the whole process over again from the beginning?
You're battery should be fine while the USB is in. It won't die on you while flashing through MAGLDR. Once the USB is in.your phone it will he fine. Silly old cautious men. haha
Sent from my HTC Vision using XDA App
lol Ok I'm going to try one more time then give up!!
I have tried both methods now
Tried installing 3 different NANDS without CWM using the DAF & get the happen error with all three:
Happen error
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: file not exist
Info: .\RSPL\RSPL.cpp (346)
Tried with & without WMDC running
Then tried as suggested using CWM but after getting through all stages the last bit I get CWM Recovery files not found!! I checked the SD card & the Cleandroid winrar file is there, its there zipped & now unzipped in a temp folder (which shows on the phone) & also in the root just in case..........nothing nada zippo.............files not found.
Any last ideas before I buy a Nokia?? lol
Its really frustrating, I managed to get all the way through on both routes but can't get the ROM installed either way.
Thanks
Are you able to go in to CWM by going to AD Recovery in MAGLDR? How are you trying to flash a ROM? Go in to the settings in WMDC and make sure the USB Connections is unchecked.
Sent from my HTC Vision using XDA App
Junks666 said:
Not yet Mez
Well I thought that seemed easy to understand TMac but.................
I intalled the cleandroid zip file but I guess since it didn't work you meant extract to the SD card (CWM didnt find the cleandroid zip file)? Also is there anyway of booting normally at the moment as I think I should charge the battery again after all this trying without success before I try again?
Thanks for your patience, I'm really not used to this sort of thing at all & at 54 yrs old I think I'm doing quite well!! lol
Click to expand...
Click to collapse
Sorry man did not mean to seem rude. I just wanted to make sure you tried the CWM method as it is the easiest way to me. also yes you are doing freaking awesome considering I know your age now. Not to say older folks are illiterate or stupid just some older people have a hard time grasping new new technologies. Don't worry none my friend, like member mezcal9 posted yesterday we will get you back going.
Also do you have this, striaght from the MAGLDR OP
You need radio which support 576 RAM.
Click to expand...
Click to collapse
Skellyyy said:
You're battery should be fine while the USB is in. It won't die on you while flashing through MAGLDR. Once the USB is in.your phone it will he fine. Silly old cautious men. haha
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
Sorry Skellyyy but yoy are wrong about this statement as you have to have a ROM runing for your battery to charge. MAGLDR does not support battery charging yet.
*Fixed Power-Off-Cable-Plug-Stop. Phone now detects this situation and reboots. Battery controller inside LEO needs runtime control during charge, it implemented in OS.
Click to expand...
Click to collapse
Notice it says it is implemented by the OS. Check my sig for a link to the thread.
Related
had this not so great idea last night that I would flash my nand android ROM for my HTC HD2 on Tmobile UK, by formatting the SD card then reinstalling CWD and flashing the ROM...
Unfortunately my fone will not switch on, I can get it into bootloader but do not know what to do from here...
any ideas?
I think I need to reinstall magdlr 1.3, then clockwork mod then my nand android rom, can anyone confirm this is right?
please help
ta
whilst I can get into bootloader and it says USB , my PC will not let me access the SD card, nothing happens at all like when the Open folder pop up appears, well it doesnt....
what have I done??
Is the HSPL 3 already installed on the phone?
http://forum.xda-developers.com/showpost.php?p=6891358&postcount=1893
You need to take your sd card out of your phone and use a card reader. There is a problem with Magdlr usb so that would be the only way to copy things to and from the sd card.
I would do a task29, reinstall magldr, clockwork and then go into clockwork and install.
Hope this helps.
bodyman
I have HPSL 2.08 do I need HPSL 3.0??
Sure I have a card reader
But its erm, well formatted now to FAT32...
Whats task29??
How can I reinstall MAGDLR when the phone will only go into bootloader but my PC will not open the sd folder?
thanks
xirokx said:
I have HPSL 2.08 do I need HPSL 3.0??
Sure I have a card reader
But its erm, well formatted now to FAT32...
Whats task29??
How can I reinstall MAGDLR when the phone will only go into bootloader but my PC will not open the sd folder?
thanks
Click to expand...
Click to collapse
quick seaches found this:
Task29
and you need to be in the bootloader to install magldr -- you use RUU to install that. Then once into madldr, then you can install clockwork -- that uses DAF.
Also, you should upgrade to 3.0.
Hope this helps
Please go read some n00b guides, everything you asked about here is VERY cleary documented, There is absolutley no need at all for this type of topic.
Not trying to be an arse but its just really annoying seeing the forums flooded with these types of topics daily and its because people dont follow simple logic and look at stickies or guide topics prior to jumping in.
trouble is when I connect my phone via usb to PC in order to update to HARDSPL3 nothing happens...
Its like my phone just will not sync with my pc
Even if I get the phone to bootloader mode, where it first says serial, when I connect the fone it does say USB but nothing else happens...
Where are these guides? why are they so hidden...
I dont know if my fone is bricked...please help
If I where you, I would start from scatch.
Go to bootloader when it says USB flash stock WM6.5
Flash HSPL 2.08
Flash MAGLDR
and so and so...
Same problem here with my boys phone. Only thing is, I can't flash anything and wmdc won't recognize the hd2. I feel like an ars lol. Just go buy an android phone and leave winmo in the dust ;-P You might enjoy unloading on it with an ar15 though muahaha
Sent from my HTC Glacier using XDA App
Try using different UBS port or UBS cord and make sure when in bootload your pc show a driver connecting with it or it won't work. And if your on window Vista or 7 try right clicking and run as admin
Also do not have your SD card in while doing this
Sent from my HTC Desire using XDA App
heres an update:
I installed HARDSPL 3.0
The phone then restarted and is working however I now need to install TASK29
But from lets call it my nand ROM main screen one it has loaded, when I connect attach a USB cable the phone will not sync will windows mobile device centre so I unable to perform TASK29
How can I get around this?
Its great the phone is working again however all I am confident after I manage to run TASK29 it will be clean so that I can install another NAND rom on to it...
Just desperately need my pc OS windows 7 to now recognise my phone so TASK 29 will work, but how?
thanks guys for your help
the plot thickens....
I went into booloader and it still shows SPL2.08 when I downloaded and installed HARDSPL3??? This is the filename I downloaded and installed HSPL3_PKG
Also after removing SD card, the phone boots into MAGDLR v1.13 and then keeps looping into reboot...
On a different note, this time when I phone switched on with USB attached but without SD CARD, my pc OS windows 7 installed a driver and it sees it but now I cannot get into the main ROM screen to run TASK29....
Gonna put the SD Card back in and hope it gets me there that way..will report back in 2 mins..
thanks for your help
so i reinstalled magldr 1.13 and clockworkmod but now when I am in magldr and go to boot ad sd I get the following error message:
load zImage
k: zimage
SD KERNAL OPEN FAILED
it cannot find clockwork mod is that right?
where do i go from here?
thanks for your help
all fixed thanks for your input especially connecting to usb ports this one thing helped me resolve everything
there should be a sticky will all info easily accessible what to do when this happens..
thanks
p.s. if anyone can tell me why my bootloader still shows hardspl 2.08 when I upgraded to 3.0 i would be grateful
thanks guys
xirokx said:
all fixed thanks for your input especially connecting to usb ports this one thing helped me resolve everything
there should be a sticky will all info easily accessible what to do when this happens..
thanks
p.s. if anyone can tell me why my bootloader still shows hardspl 2.08 when I upgraded to 3.0 i would be grateful
thanks guys
Click to expand...
Click to collapse
3.0 is just an update to 2.08 that works for the newer hd2's
also, task29 will format your NAND -- it is like the ultimate hard reset. I use it when I switch from different roms. That way there is no residuals left over from any previous roms that may or may not cause problems.
check here for any ?'s that you might have. All stickies have been rolled up into one thread.
Well i noticed that task29 doesn't wipe everyhing. I had issues with various rome for a while, I tried task29 many times with no success, the only thing that solved theme where flashing stock 6.5...
And don't go to spl3 or you won't be able to flash magldr, stay on 2.08
xirokx said:
all fixed thanks for your input especially connecting to usb ports this one thing helped me resolve everything
there should be a sticky will all info easily accessible what to do when this happens..
thanks guys
Click to expand...
Click to collapse
Is this a joke? i mean, the stickies are there, you only need to read them and follow the steps you have tutorials and howtos in task29 thread, then in the hardspl thread and in the hd2 sections (sd,nand).
anyway, i am glad, you worked it out
Hi...
I have a TMOUS HD2 and I had a MDJ Rom on it but i travelled to India and i had occasional hangups and restarts with the phone. So i tried flashing to a different ROM and i tried MIUI but the condition persisted (HAD MAGLDR 1.11 and CWM 1.2)
However that didnt work and i couldnt update the radio too (assuming that the EDGE connection is messing up the phone)
So i flashed back to the TMOUS Stock Rom RUU_Leo_1_5_TMOUS_2.10.531.0_Radio_Signed_15.34.50.07U_2.08.50.08_2_Ship
and installed Radio 2.15.50.14 and HSPL 2.08.
After that i tried installing MAGLDR (1.13) in my Windows 7 system but it wouldnt. So i used a windows vista system and installed it using Romupdate utility.
Now i am trying to install CWM 1.3 but i keep getting this error
An error has occurred
Read below for more information
Error Description: send partition data failed
Info: .\RSPL\RSPL.cpp (815)
Error Description:
Info: .\RSPL\RSPL.cpp (558)
On phone:
Partition layout same
Erase
...
...
Save EMBR...
Default OS is AD NAND
Empty 0 partition .. OK
Flashing 1 partition... 1 [221-23E] MO
Can someone help pls? i couldnt post in the development forum cos i have to make atleast 10 posts else i would have posted this in the CWM 1.3 thread or this one even http://forum.xda-developers.com/showthread.php?t=981811.
Also in option USB Flasher from MAGLDR
the prompt says WAIT USB... even after connecting the USB to the phone. HOwever on running the DAF, it comes as WAIT USB...USB but many threads say that it has to be WAIT USB..USB even before running the DAF for CWM.
Thanks in advance
Andrew
Shamelessly bumping the thread so that someone could help me!!!
AJ
What's wrong is that you have allowed USB connections in ActiveSync. Open ActiveSync and untick the "allow USB connections" box and reflash and it'll flash correctly.
Ok... since its windows 7 / Vista there is only Mobile Device Center and i have unchecked the option "Allow USB Connections" And I still get the error...
Is there any workaround for this ?
Does anyone know why there was frequent system hangups ? Could someone help me find the root cause of this one ?
I am trying to install any new rom and see if the problem disappears in anything. But unfortunately I am stuck with CWM install.
AJ
which size cwm are you trying? there have been a few reports lately (myself included) that teh 150 ver failed in various ways, , download the 250meg ver and edit flash.cfg to 150 (or just leave as 250 for a quick test flash) and see if it works.
samsamuel said:
which size cwm are you trying? there have been a few reports lately (myself included) that teh 150 ver failed in various ways, , download the 250meg ver and edit flash.cfg to 150 (or just leave as 250 for a quick test flash) and see if it works.
Click to expand...
Click to collapse
Hi,
I tried the 250 one and the 450 one but it still fails. I dont know what is going wrong.
AJ
Try doing it like this.
Turn on your phone with vol down key held to enter bootloader (tri colour screen)
Run Task29.
When the phone reboots hold vol down again to get back into bootloader.
Flash MAGLDR 1.13 from bootloader by running "ROMUpdateUtility" instead of the DAF.exe.
Should work without a problem, I always flash MAGLDR like this.
I don't think it relies on mobile device centre like this so should eliminate any problems in that area.
This time when it reboots hold the power button to get into MAGLDR. Select USB flasher and flash the 150MB CWM partition. I sometimes have problems with the larger partitions but 150MB one always works.
Then install which ever rom you use using recovery option from MAGLDR.
Also make sure you have the latest versions of everything:
MAGLDR 1.13 - http://forum.xda-developers.com/showthread.php?t=893618
CWM partition should be version 1.3 - http://forum.xda-developers.com/showthread.php?t=898913
zX TheRipper Xz said:
Try doing it like this.
Turn on your phone with vol down key held to enter bootloader (tri colour screen)
Run Task29.
When the phone reboots hold vol down again to get back into bootloader.
Flash MAGLDR 1.13 from bootloader by running "ROMUpdateUtility" instead of the DAF.exe.
Should work without a problem, I always flash MAGLDR like this.
I don't think it relies on mobile device centre like this so should eliminate any problems in that area.
This time when it reboots hold the power button to get into MAGLDR. Select USB flasher and flash the 150MB CWM partition. I sometimes have problems with the larger partitions but 150MB one always works.
Then install which ever rom you use using recovery option from MAGLDR.
Also make sure you have the latest versions of everything:
MAGLDR 1.13 - http://forum.xda-developers.com/showthread.php?t=893618
CWM partition should be version 1.3 - http://forum.xda-developers.com/showthread.php?t=898913
Click to expand...
Click to collapse
Hi,
I tried doing like you said.
I downloaded TASK29...
Got into bootloader (4 color screen).
Connected the USB cable... waited for drivers to install and then waited till the prompt changed from SERIAL to USB.
Started TASK29. (as adminstrator - windows vista 32 bit)
Showed Image version as blank and Updated ROM as 2.00.000.00.
Clicked on NEXT and then the Screen changed the HTC with 0%.
It is stuck there.
Now i am unsure what to do.
AJ
HunterAJ said:
Hi,
I tried doing like you said.
I downloaded TASK29...
Got into bootloader (4 color screen).
Connected the USB cable... waited for drivers to install and then waited till the prompt changed from SERIAL to USB.
Started TASK29. (as adminstrator - windows vista 32 bit)
Showed Image version as blank and Updated ROM as 2.00.000.00.
Clicked on NEXT and then the Screen changed the HTC with 0%.
It is stuck there.
Now i am unsure what to do.
AJ
Click to expand...
Click to collapse
Don't know if you should unplug the phone. After it's started, it's possible to brick your device by unplugging in the process of wiping. I don't have any advice after that, but just a note if you're wondering whether it's safe to unplug. Wait 'til someone other than I with experience says otherwise. Sorry and good luck.
That has happened to me once before, not sure if it was during Task29, flashing a stock rom / radio or MAGLDR. I left it for a long time and in the end decided there was nothing I could do but pull the battery and pray my phone wasn't bricked. Luckily it was ok and I tried again and everything was fine. Don't think anyone will tell you to do that though because none of us want to be responsible for bricking your phone!
If it hasn't got anywhere after 10 minutes or so then I guess you won't have much choice.
In theory if it's stuck at 0% then it hasn't started yet so it might be ok to unplug and pop the battery but don't take my word for it.
Would probably be more of a risk if it was half way through and you unplugged it.
Good Luck!
Well i did post earlier that i didnt brick my phone yet... but i have tried everything else that has been said in the community and now i am losing all hope of getting the android to work on my HD2...
Can someone pls help ??
Cotulla / bebe - Anyone ? I know you possibly might not check these forums but just wanted to ask your help.
AJ
Give this a try...
Use the task29 from my thread .. do what it says ..
DL one of the setup programs.. 150 - 430 depending on what ROM you want.
And follow the on screen helps ..
http://forum.xda-developers.com/showthread.php?t=981811
Hi there
I got an HD2 from a friend (he bought off ebay) and seems to just boot to the Tmobile sticking together logo and won't boot.
I don't think it charges as well...
there was no lines (radio?) at the bottom of the Sticking Together pink square screen...
is this phone bricked? or can I still flash a rom?
Ok try this, turn the phone off then hold the low volume botton n the power botton at the same time, n if it takes u to the bootloader then u r good, just search on how to install a rom of ur choise, good luck
Sent from my HTC HD2 using XDA Premium App
froibet said:
Hi there
I got an HD2 from a friend (he bought off ebay) and seems to just boot to the Tmobile sticking together logo and won't boot.
I don't think it charges as well...
there was no lines (radio?) at the bottom of the Sticking Together pink square screen...
is this phone bricked? or can I still flash a rom?
Click to expand...
Click to collapse
Well the fact that it will even turn on means it is not bricked. A bricked HD2 will not even turn on the most it will do is flash tihe led light and vibrait a couple of times.
Follow the instructions of the above post and pull up bootloader, if bootloader comes up you can save the HD2. Depending on if you want to flash a official srock ROM or a custom ROM to the HD2 will dictate your next step.
If you want a official stock ROM then just download and flash the official update from T-Mobile.com just type in HTC HD2 update in the search box on the home page and you will find it. You will have to enter the IMEI number to download it wich you can find this number behind the battery. To flash it connect the HD2 to a computer via USB cable while in bootloader and wait for the serial in the white bar at the bottom of the bootloader screen to change to USB and the computer to show it recognizes the HD2 then run the update utility and follow all the on screen instructions.
If you want to flash a custom ROM as in custom Windows Mobile, NAND Andriod ROM, or Windows Phone 7 ROM then you will have to flash HSPL to the HD2. Download HSPL4 and flash 2.08 HSPL if hou want to flash a NAND Andriod ROM as MAGLDR only supports 2.08 HSPL. Or a Windows Phone 7 Rom, or flash 3.03 if you just want to flash a custom Windows Mobile ROM.
Now if you want a NAND Andriod ROM or Windows Phone 7 you will have to download MAGLDR and flash it to the HD2.
If you want a custom Windows Mobile ROM download the ROM of your choice and fladh it using the .exe or RUU wich ever one the ROM has. Note do all flashing of what I have previously mentioned via the method I mentioned before.
If you are wanting to flash a NAND Andriod ROM or Windows Phone 7 ROM then download the ROM of your coice and flash it using MAGLDR and the instructions of the ROM developer in thread for the ROM.
Now this is very important. I see from the picture you have a T-Mobile(TMOUS) HD2 so no matter what you do, do not flash a ROM with a radio version that reads like these 2.04.50.xx, 2.05.50.xx, or any radio that is x.xx.51.xx they will brick/kill a TMOUS HD2.
froibet said:
Hi there
I got an HD2 from a friend (he bought off ebay) and seems to just boot to the Tmobile sticking together logo and won't boot.
I don't think it charges as well...
there was no lines (radio?) at the bottom of the Sticking Together pink square screen...
is this phone bricked? or can I still flash a rom?
Click to expand...
Click to collapse
I would recommend flashing a stock T-Mobile ROM, since that appears to be the flavor of the phone. This will install the correct radio. Once the phone is working, continue as per normal for flashing the ROM. You will have to reinstall hardspl.
thanks for the info guys! i really appreciate the support!
it seems like it won't read the USB... is the port busted?
froibet said:
thanks for the info guys! i really appreciate the support!
it seems like it won't read the USB... is the port busted?
Click to expand...
Click to collapse
try this:
1) download your stock ROM.
2) put it on your SD card via a card reader, you want an .NBH file.
3) rename the file LEOIMG.NBH
4) make sure the phone is off, make sure your SD card is back in your phone.
5) hold down and power
6) it should go to a tri-color screen and say something about flashing the image, hit power to confirm
7) it should flash no problems.
MAKE SURE YOU DOWNLOAD THE CORRECT ROM FOR A TMOBILE US HD2
Have exactly the same problem with my friends phone.
Its a TMOUS and sticks on the same boot screen.
He screwed it up when trying to install Android NAND on it.
I can enter bootloader And I have managed to get rid of MAGLDR and CWM.
I have HSPL 3.03 installed on it, but when I try to install the latest ROM from TMOUS it fails at 8% and tells me that
'ERROR 290: INVALID COMMAND
This update Utility cannot be used for your PDA phone. Please check your update utility'
Tried copying the relevant file to the SD card and renaming it leoimg.nbh but the install fails HERE aswell with the error:
"RADIO_V2 - RSA Fail"
I managed to install an energyrom onto it, but it wouldnt go past the initial boot screen
Any help appreciated
Boradan said:
Have exactly the same problem with my friends phone.
Its a TMOUS and sticks on the same boot screen.
He screwed it up when trying to install Android NAND on it.
I can enter bootloader And I have managed to get rid of MAGLDR and CWM.
I have HSPL 3.03 installed on it, but when I try to install the latest ROM from TMOUS it fails at 8% and tells me that
'ERROR 290: INVALID COMMAND
This update Utility cannot be used for your PDA phone. Please check your update utility'
Tried copying the relevant file to the SD card and renaming it leoimg.nbh but the install fails HERE aswell with the error:
"RADIO_V2 - RSA Fail"
I managed to install an energyrom onto it, but it wouldnt go past the initial boot screen
Any help appreciated
Click to expand...
Click to collapse
Try running a Task 29 on your friends HD2. This willtotally clean out the NAND memory of the HD2 and reformat it, kinda sounds like that is what is needed to be done. He may have messed the NAND memory format up when he was trying to install the Andriod. You will have to reflash a Windows Mobile ROM after you run the Task 29 as it will not ha e a ROM on the phone then. You will not have to reflash HSPL cause it will not remove it.
It seems that the problem is RADIO related. I can task 29, and I can install The latest Energyrom, but I CANT install a radio.
There is no radio ON the phone at the minute it seems. When I try to do a radio install, it asks me if I want to go from version ' ' to the update I am using.
None of the installers see a radio on the phone, and trying to install the radio always fails at 96%. This would seem to be the same if I try to install the official TMOUS latest ROM with radio from SD Card. It fails at the radio install part.......
Maybe time for a new thread for this one.......
orangekid said:
try this:
1) download your stock ROM.
2) put it on your SD card via a card reader, you want an .NBH file.
3) rename the file LEOIMG.NBH
4) make sure the phone is off, make sure your SD card is back in your phone.
5) hold down and power
6) it should go to a tri-color screen and say something about flashing the image, hit power to confirm
7) it should flash no problems.
MAKE SURE YOU DOWNLOAD THE CORRECT ROM FOR A TMOBILE US HD2
Click to expand...
Click to collapse
i can do all this without connecting to the PC? just flashes from the SD card???
froibet said:
i can do all this without connecting to the PC? just flashes from the SD card???
Click to expand...
Click to collapse
Yes you can flash radio and ROM from your SD card. Here is a link to the thread on doing this gives step by step, check it out.
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
when you turn on your phone hold the red power button until the magldr screen pops up then go to flash to usb then download the stock rom for win 6.5 it should be in the win6.5 development threads on XDA the rom should be a .exe file, run the file once u establish a usb connection with the computer. if you can't get on the magldr screen, try going to the boot screen ( the one with the color stripes) and re-flash your magldr or the hspl4. as long as you can get into the magldr boot screen then you should be able to flash android or winmo. hope that helps.
Phongsta said:
when you turn on your phone hold the red power button until the magldr screen pops up then go to flash to usb then download the stock rom for win 6.5 it should be in the win6.5 development threads on XDA the rom should be a .exe file, run the file once u establish a usb connection with the computer. if you can't get on the magldr screen, try going to the boot screen ( the one with the color stripes) and re-flash your magldr or the hspl4. as long as you can get into the magldr boot screen then you should be able to flash android or winmo. hope that helps.
Click to expand...
Click to collapse
This couldn't be more wrong lol. You can't flash WinMo ROM's from MAGLDR, only WP7 and Android.
Anyway why don't you just try flash a different Android ROM? Even one that has a daf and not a .zip that you have through CWM.
If you do want to go back to stock though, download your stock ROM from the HTC site or T-mobile depending on which phone you have (T-mobile say t-mobile at the top and has red and green call/end buttons). Then once you've downloaded it, rename the file to .zip (should be .exe by default) then using WinRar open the file and look for a file that ends with '.nbh' in WinRar. Once you've found that file just extract it to wherever you want and rename it to 'LEOIMG.nbh'. Once you've done that, place it on the root of your SD card, then POP your SD card back in to your HD2, boot to HSPL (tri colour) and you'll come to a screen which will allow you to flash the ROM from SD and you're done.
PS. you need a 4GB or smaller SD card to flash it.
Good luck.
Sent from my HTC Vision using XDA App
Skellyyy said:
This couldn't be more wrong lol. You can't flash WinMo ROM's from MAGLDR, only WP7 and Android.
Anyway why don't you just try flash a different Android ROM? Even one that has a daf and not a .zip that you have through CWM.
If you do want to go back to stock though, download your stock ROM from the HTC site or T-mobile depending on which phone you have (T-mobile say t-mobile at the top and has red and green call/end buttons). Then once you've downloaded it, rename the file to .zip (should be .exe by default) then using WinRar open the file and look for a file that ends with '.nbh' in WinRar. Once you've found that file just extract it to wherever you want and rename it to 'LEOIMG.nbh'. Once you've done that, place it on the root of your SD card, then POP your SD card back in to your HD2, boot to HSPL (tri colour) and you'll come to a screen which will allow you to flash the ROM from SD and you're done.
PS. you need a 4GB or smaller SD card to flash it.
Good luck.
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
I think this should work for you ,,, it always work for me this way
mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
WOW!! for a newbie, u sure know how to go for d big guns ...Anyway according to your post, i tk it u downloaded the "TyphooN_CM7_v2.8.0-cLK.zip" file ryt?...Well in [cLK/MAGLDR]TyphooN CyanogenMod 7 RC2+ v2.8.4's thread, it tells you there are two ways to install this particular build...I'm guessing u tried installing the "TyphooN_CM7_v2.8.0-cLK.zip" thru MAGLDR-CWM instead of following Charmacas's cLk tutorial.
So in d spirit of learning, Start d whole process again (Task 29, etc), go back to the build's thread (link above), choose which method is most comfortable 2 u ( i recommend MAGLDR) and re-download the latest & APPROPRIATE build for the process or just download from the links below....
MAGLDR Method.
cLK Method.
Nw abt reflashing WinMO, U've got HSPL installed so u r good...Just perform a Task 29 (dis wipes ur phone clean, leaving ur HSPL & radio intact) from the bootloader screen...Should usb fail? unplug n try another usb port on your pc...Then simply flash ur desired WinMo ROM.
This my friend is what happens when dev's instructions are not followed...Do read, understand n be more careful nxt time...Donate to the devs if i helped u.
All done !
voncrane said:
WOW!! for a newbie, u sure know how to go for d big guns ...Anyway according to your post, i tk it u downloaded the "TyphooN_CM7_v2.8.0-cLK.zip" file ryt?...Well in [cLK/MAGLDR]TyphooN CyanogenMod 7 RC2+ v2.8.4's thread, it tells you there are two ways to install this particular build...I'm guessing u tried installing the "TyphooN_CM7_v2.8.0-cLK.zip" thru MAGLDR-CWM instead of following Charmacas's cLk tutorial.
So in d spirit of learning, Start d whole process again (Task 29, etc), go back to the build's thread (link above), choose which method is most comfortable 2 u ( i recommend MAGLDR) and re-download the latest & APPROPRIATE build for the process or just download from the links below....
MAGLDR Method.
cLK Method.
Nw abt reflashing WinMO, U've got HSPL installed so u r good...Just perform a Task 29 (dis wipes ur phone clean, leaving ur HSPL & radio intact) from the bootloader screen...Should usb fail? unplug n try another usb port on your pc...Then simply flash ur desired WinMo ROM.
This my friend is what happens when dev's instructions are not followed...Do read, understand n be more careful nxt time...Donate to the devs if i helped u.
Click to expand...
Click to collapse
Thanks m8... I figured out my problem... HAVE TO RUN EVERYTHING 'AS ADMINISTRATOR' ... anyway... won't make that mistake again...
Thanks Everyone for all your help!!!!
mburian said:
Thanks m8... I figured out my problem... HAVE TO RUN EVERYTHING 'AS ADMINISTRATOR' ... anyway... won't make that mistake again...
Thanks Everyone for all your help!!!!
Click to expand...
Click to collapse
Glad 2 help, just hit d thanks button nxt time....Enjoy ur device.
mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
you must istall zip for MAGLDR not for CLK!!
mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
you must istall romzip for MAGLDR not for CLK!!
i just put on nand rom for the first time, and i want to re-do it with american android, but when i try running magldr 1.13, it says usb not connected and i cant get past this to flash american android, any answers for this plz, ty much, error :260:
can you give us pls some more input on what you are doing exactly? Where does it get stucked, when you boot it or do you select something from the menu and then the problem with no usb connected occurs?
well when i go into magldr and try to get it to go into usb flash, so i can flash american android, it opens and i check the boxes and click next, then it scans for the usb, but it wont bring up an error, and it tells me to make sure my usb is connected and it is connected already???? im a noob at this so i cant explain to much into what im doing wrong, im just going by the steps ive read, i have android on it and it works just great, but i want a dif rom, not the stock rom i found.
when you choose usb flasher do you see:usb flasher......usb
i think americandroid is using daf method.so right click on aca.exe and run as administror.
be sure you downloded mgldr version of it (not clk)
never mind, my mistake
when i try running magldr it says error and it wont run magldr, and usb is connected, but it says it isnt...?
plz can anyone tell me what im doing wrong??? im running magldr and my hd2 is connected, but when i check the boxes in magldr and click next it looks for my pda, then says error 260 and make sure cradle/cable is plugged into pc, and it is, and it wont go into magldr so i can click usb flash drive...???
please be more specific and write your steps. what do you mean by saying ' i'm running mgldr'.have you flashed it to your phone in usb flasher mode? what are specifications of your phone.have you done these:
1)hspl 2.08
2)task 29?
3)flash mgldr
4)partition of sd
5)partition of nand by cwr
mutil said:
please be more specific and write your steps. what do you mean by saying ' i'm running mgldr'.have you flashed it to your phone in usb flasher mode? what are specifications of your phone.have you done these:
1)hspl 2.08
2)task 29?
3)flash mgldr
4)partition of sd
5)partition of nand by cwr
Click to expand...
Click to collapse
ok last night i did my first nand on my nd2, i ran the hspl, then i ran the magldr 1.13, then i scrolled down to usb flasher, then i ran the rom that the youtube link gave me, http://www.youtube.com/watch?v=cvS4EvS0PAw then it all worked, i had android on my phone, but i dont want the rom in the youtube link, i want one from this forum american android, and i was wondering, when i go to run magldr on my nand android i flashed, it tells me error and that to check if my phone is connected, and im just trying to do what i did in the youtube video but with a dif rom, but it wont work from android, it did just fine on wm 6.5, and my phone is connected to the usb, but it tells me it isnt, but i can still transfer music and other things, but when i go to run magldr it tells me my phone isnt connected, so i cant get into magldr and scroll down to flash usb and use the rom i want to use from this site, better? plz help thanks much.
in order to go into mgldr menu power off the phone.then power on but hold down the power key until mgldr menu comes. its not necessary to reload mgldr for each rom.if you installed it to your phone now it is in it.
i left it alone, and i powered off and tried turning it back on this morning when i woke up, and it powers on and then stops on quietly briliant, it wont even go into android now, is there any way i can go back to wm 6.5? or make my phone work again? when i go into magldr in usb flasher mode and try flashing a new rom, it tells me an error has occurred, error descriptio: USB init failed info: \rspl\rspl.cpp 736??? now my phone doesnt work at all... :<
getting phone working...
_fly
have you used the the HD2 toolkit? You can find/download from here
http://forum.xda-developers.com/showthread.php?t=1090783
try wiping the phone with task29, then loading the MAGLDR or cLK / which ever nand/rom you want to use. Hopefully this works for you....
_fly said:
i left it alone, and i powered off and tried turning it back on this morning when i woke up, and it powers on and then stops on quietly briliant, it wont even go into android now, is there any way i can go back to wm 6.5? or make my phone work again? when i go into magldr in usb flasher mode and try flashing a new rom, it tells me an error has occurred, error descriptio: USB init failed info: \rspl\rspl.cpp 736??? now my phone doesnt work at all... :<
Click to expand...
Click to collapse
you mustn't flash new roms in mgldr-usb flasher mod.
1)just put rom.zip into sd
2)go to mgldr-ad recovery-install zip from sd-choose zip from sd-find rom in the list and choose with call button.after installation is completed reboot.
try these with that rom:http://forum.xda-developers.com/showthread.php?t=933951
mutil said:
you mustn't flash new roms in mgldr-usb flasher mod.
1)just put rom.zip into sd
2)go to mgldr-ad recovery-install zip from sd-choose zip from sd-find rom in the list and choose with call button.after installation is completed reboot.
try these with that rom:http://forum.xda-developers.com/showthread.php?t=933951
Click to expand...
Click to collapse
when i go into ad recovery it says no boot source???
Then you have to install cwm first.
I have had a similar problem with my phone and what worked for me was disconnecting the usb cable and plugging it back in. then it seen it as usb and i was able to flash the ROM. i know it seems rather simple but this small fix might work for you as it did for me.
if you can install cwm i would highly suggest to do that and also looking into the hd2 toolkit as someone else as already pointed out.