Need fellow Atrix owner's response... - Atrix 4G General

I've noticed on my Atrix two interesting things about the glass and I was wondering if fellow Atrix owners could give me an idea if their Atrix has the same issue:
1.) On the right side, the glass is sunk a tiny bit below the casing/frame so that when you run your finger on the glass left-to-right and go off the right edge, you feel a slight "bump". BUT on the left side the glass is more or less flush with the casing/frame. Perhaps (maybe just in my head) very slightly above it.
2.) When pushing on the corners or edges (lightly) there is a bit of play where the glass "squishes" down a bit. It feels almost as though it's like there is a tiny rubber gasket under it allowing it to take a bit or absorption.
Has anyone else noticed either of these issues, more importantly #1? I figure #2 is standard and I'm not concerned about but with #1 I really don't want to find myself down the road having issues with the front glass.
Thanks very much.

I just checked mine and I didn't notice either of these issues, if you're within 30 days I'd recommend an exchange....

I notice #2... there definitely is some play and I remember reading that some others reported this as well. Have to push quite hard on it though, definitely not noticeable during normal use.
Gabbosgreats said:
I've noticed on my Atrix two interesting things about the glass and I was wondering if fellow Atrix owners could give me an idea if their Atrix has the same issue:
1.) On the right side, the glass is sunk a tiny bit below the casing/frame so that when you run your finger on the glass left-to-right and go off the right edge, you feel a slight "bump". BUT on the left side the glass is more or less flush with the casing/frame. Perhaps (maybe just in my head) very slightly above it.
2.) When pushing on the corners or edges (lightly) there is a bit of play where the glass "squishes" down a bit. It feels almost as though it's like there is a tiny rubber gasket under it allowing it to take a bit or absorption.
Has anyone else noticed either of these issues, more importantly #1? I figure #2 is standard and I'm not concerned about but with #1 I really don't want to find myself down the road having issues with the front glass.
Thanks very much.
Click to expand...
Click to collapse

Hadn't noticed before but yes on mine to both. Its nothing id worry about
Sent from my MB860 using XDA Premium App

Gabbosgreats said:
I've noticed on my Atrix two interesting things about the glass and I was wondering if fellow Atrix owners could give me an idea if their Atrix has the same issue:
1.) On the right side, the glass is sunk a tiny bit below the casing/frame so that when you run your finger on the glass left-to-right and go off the right edge, you feel a slight "bump". BUT on the left side the glass is more or less flush with the casing/frame. Perhaps (maybe just in my head) very slightly above it.
2.) When pushing on the corners or edges (lightly) there is a bit of play where the glass "squishes" down a bit. It feels almost as though it's like there is a tiny rubber gasket under it allowing it to take a bit or absorption.
Has anyone else noticed either of these issues, more importantly #1? I figure #2 is standard and I'm not concerned about but with #1 I really don't want to find myself down the road having issues with the front glass.
Thanks very much.
Click to expand...
Click to collapse
It is normal. The only time you should be worried is if the glass is lifting and you can actually see the edges of the glass. But as long as it is flush or deeper there's nothing to worry about. It's common amongst phones with fronts that are completely glass. The iPhone 4 doesn't have this problem because they use a harder plastic material as a "gasket" but that is also why their back glass panels are so easy to break. I would rather have a little "play" then worry about dropping my phone 4 inches from the ground.

mine is solid, solid as a rock..

Thanks for the replies. Anymore owners care to chime in?
Sent from my MB860 using XDA App

For issue 1 I have that also for issue 2 take off your battery cover and see what happens. I had it really bad until I got my battery cover replaced at AT&T. Once I did that it reduced significantly, seems to be some Battery Covers don't fit just right.
Gabbosgreats said:
I've noticed on my Atrix two interesting things about the glass and I was wondering if fellow Atrix owners could give me an idea if their Atrix has the same issue:
1.) On the right side, the glass is sunk a tiny bit below the casing/frame so that when you run your finger on the glass left-to-right and go off the right edge, you feel a slight "bump". BUT on the left side the glass is more or less flush with the casing/frame. Perhaps (maybe just in my head) very slightly above it.
2.) When pushing on the corners or edges (lightly) there is a bit of play where the glass "squishes" down a bit. It feels almost as though it's like there is a tiny rubber gasket under it allowing it to take a bit or absorption.
Has anyone else noticed either of these issues, more importantly #1? I figure #2 is standard and I'm not concerned about but with #1 I really don't want to find myself down the road having issues with the front glass.
Thanks very much.
Click to expand...
Click to collapse

Mine has both 1 and 2.

I've got both also. No biggie.
Sent from my MB860 using XDA App

I have both as well. I'm not worried either.
I think #1 might just be the entire phone being pushed further into the plastic backing and not actually the screen getting pushed into the internals of the phone.

Thanks for the responses. This helps in a big way. I'm guessing I should RDWHAHB and just use the phone. If it leads to any deficiency, it would likely occur within the 1 year warrenty (knock on wood).

Related

Dust in LCD

I an always overprotective of a new gadget, and the Evo I am getting tomorrow will be no exception. I was looking through a blog and I saw an image of the front glass being removed. They noted how easy it is to remove, and lauded this as a feature. When I see this, all I can think is about the horror I felt when I found a stream of dust particles between the LCD and the glass on my iPhone and my Sprint Hero (and yeah, every single other thing I ever get, somehow).
I was thinking about how much I hate this and I want to avoid it this time around. For those of you that use full body cases, have you ever had this problem? For that matter, has ANYONE ever had this problem? I wouldn't be that surprised if it turned out I am alone in my compulsiveness.
Regards!
Pick it up and blow on it....jk
I highly doubt that anyone has had this prob. The reason why on the video it was like that is because he had already taken the screen of a million time before.
there is a tiny gap in the seam between the screen and the housing and i have already seen dust get in there
however i have not seen any dust under the glass (yet) and i have definitely been watching out for it. i'm hoping my silicone skin that covers the seam will help to prevent dust seepage (like it did with my hero, though my hero eventually got dusted regardless)
The n1 had this issue but i have not seen one post about evo with dust. My evo looks and feels like it was built 10x better then my n1.
i have some dust building up on top left corner...right below the hTc logo
I've had dust under my screen on the top left underneath the htc logo for like 2 weeks. I have no idea how it got there. Very aggravating
Sent from my EVO using XDA App
I use the seidio active case and have no dust. Had the phone since launch day
Sent from my PC36100 using Tapatalk
Evos have had issues with the screen rising up due to improper adhesion.
Solution involves using a hairdryer on hot to gently heat the adhesive while pushing down on the screen.
I am uncertain whether what I stated is the correct method or not. I read it some time ago, and I cannot remember where.
Just noticed quite a bit of dust in the upper left corner of the lcd... Can't unsee it now. Seems there are a bunch of reports of this exact area being a problem.
konfuzed said:
i have some dust building up on top left corner...right below the hTc logo
Click to expand...
Click to collapse
Same here. It is way less noticeable than my hero was.
Top left corner = dust
I noticed dust in the top left corner since 6 days after getting thephone
Sent from my PC36100 using XDA App
We need some pics of phones with this effect. My screen has the dust too. Its bs. It has never been dropped in dirt or near the beach yet when the screen is off its obvious.
Sent from my PC36100
So went to Sprint one day to ask if they could clean the dust that is in the top left corner (which has been done on my previous hero phone a lot) and i was told that they didn't have too because that is normal wear and tear. Like if your car was to get dust in it the dealership wouldn't be responsible. I just laughed in his face and said are you serious. I have all the protection plans and i demanded he go and clean it. Then he tells me that he has to take off my protection screen because he claimed that there was dust under that. Which i know how to put on a screen in dust free area and it was impossible for dust to get under it when the screen is on. This guy was an idiot. So he went in the back and came out moments later saying well we moved the dust off the screen but they couldn't remove it from the phone. I looked at the phone and the dust appeared to be gone. About 15 min later the dust was back. I am not sure was is going on but it is really wierd that all of you have the same dust in the upper left hand corner like mine. Anyone else go to sprint and ask about it? I am curious to here what they have told you. I am going to another sprint store to see what they say to me this time
There is another thread about the same thing. Its probably the headphone jack.
x iFLaWz said:
There is another thread about the same thing. Its probably the headphone jack.
Click to expand...
Click to collapse
It is because of the headphone jack. Its going to happen to all EVO's, just the nature dust and having a jack near the screen like that without being fully protected from the lcd screens.. Case's do help and I've heard of plugs coming out to plug into the jack to prevent dust and moisture getting inside.
All of a sudden silicone caps for ports don't sound so 1995 anymore. Im not sure its the headphone jack, to me it looks like its getting in around the earpiece/speaker. Not sure of that though.
My first handset had dust in the upper left corner.. one of the main reasons I asked for an exchange. My second handset has dust accumulating in the same spot but I'm trying to ignore it.. =\
The Evo I have now has dust in the bottom right corner. Noticeably a large piece about 2mm from the bottom. I got sent a replacement from sprint due to another issue, and right out of the plastic packaging i noticed a LARGE piece of dust right in the middle of the screen. Very annoying, and I sent it back. I cannot believe HTC would let this get through a quality inspection.

Screen raised a little bit higher than the bezel near the dock connector

I'm close to my 14 days return period at bb and suddenly I noticed that the glass screen on my Iconia is separating a bit noticeable enough for my fingers to feel it when I touch that section. It is the area at the docking connector side, the screen is raised a bit higher than the side metal bezel. When I pushed it down hard it flushed back in but raised again after some time. I never noticed it before and I've been really using it daily for more than a week now and only until yesterday I saw this. I feel really bad because I really love my Iconia and was really planning to keep it. I had the same issue with my HTC EVO, but I held on to it because I've read in the EVO forum that others have even worst screen separation and mine wasn't as bad. So I'm wondering if most Iconias have this issue so I don't need to return it anymore. I've checked the display unit at bb and it has same screen lifting around that section near the docking connector.
Sent from my A500 using Tapatalk
Same issue here. I noticed it the other day. I have a week left on my 14 day return period. Honestly it is not that big of a problem to me. I cannot push it back down, I just figured it was made that way. I noticed the demo unit at my local best buy was the same way. I do not think it is a deal breaker to me.
Yeah mine is like that too :\
MMm - no trouble here yet. Then again I was a first generation nook owner who never had a button crack, and those were hard to find ;-)
I take mine to and from work every day and use it at least 2 hours a day not counting weekend software development time where it's my test platform, so you could call mine pretty high wear and tear.
So it seems like it is common to have that slight lift on the screen and hopefully will not get worst than it is. I will just keep it and not replace with another one, who knows the replacement might even be worst or have dust like the others were complaining. I've put too much time setting this up and I really love it even with all the criticism it gets from other users.
I feel a slight raise on mine - but far from calling it an issue.
There's some dust particles getting under there now...think Staples would accept a return for that? Still in my 14 days. It's annoying.
Staples told me they would take it back for any reason in 14 days... even if you just decided you didn't like it.
cdkizzle said:
There's some dust particles getting under there now...think Staples would accept a return for that? Still in my 14 days. It's annoying.
Click to expand...
Click to collapse
Oh no, I hate dust inside the screen. Was your screen raised really high or just a bit?
Sent from my A500 using Tapatalk
lol. There shouldn't be any question at all....take it back.
I'm not returning mine but this is irritating for sure
I believe it is designed that way, just as there is the gap between the glass and frame on the opposite side (where the microphone is placed in the center).
I for one find the A500 a great piece of hardware, and this doesn't bother me a bit... I actually hadn't noticed until you mentioned it here ;-)
Sent from my A500 using XDA Premium App
Raised here as well
Looks like an intentional raise to me though. The sides are flush and begin to raise about 1.5 inches in from the side of the tablet toward the center until it reaches it's highest point dead center to the dock port. Then back down by the same amount.
If it is not intentional it sure is a nicely implemented defect.
If I run my finger along the edge of the screen I can feel the glass being raised ever so slightly, fractions of a millimeter, towards the middle, above the dock connector.
Though as I look closer and use a metal ruler I find that it's not the glass that is raised but rather the bezel that is lowered slightly in the middle, above the connector.
All of them I have seen are like that, don't think its a defect at all.
It looks like it is easy for dust to get in past the microsd slot area as you can see the back of the screen through the cracks. I would be careful outside and in dusty areas. I am going to look for a sleeve that covers it or something...it should be sealed better than this.
I haven't had any dust yet, (hopefully never) and my screen is raised. (or the bezel is lowered)
I'm getting that too now. It's definately raised. I checked when the OP first posted this and it was not like this. Now I can press on the glass just above and slightly to the right of the dock connector and the screen goes down flatter. The raised area is not quite centered. I've had this tablet 3 days shy of 1 month.
Sent from my A500 using Tapatalk

Build quality issues.

I have to exchange my acer, the screen at the bottom near the dock sticks up past the outer frame. If you push right there it moves also. You can definitely feel the edge of the glass sticking up. Has anyone else had this issue?
~Sent using my Humble Charge~
Mine does at the top right corner.. and its slighty spongy. lots of people have said the same thing.. This is due to the design of the glass going all the way to the edge with no frame. Mine has been this way since day one and has not gotten any worse .i could see how there could be a assembly issue causing this to be much worse for some.. mine is appox the thickness of a credit card higher then the frame on that side..that is with the screen protector on it ..
I would use your own descression on rather to exchange it or not
Maybe I am being to picky but, it sticks up about as far as you said, about the thickness of a credit card for a good 3 inches along the bottom edge.
~Sent from my Droid SuperCharge~
Spoiled Customer
You have every right to take it back.. its a expensive device.. I have mine in a case with screen protector so does not bother me.. If it were a scratch on my van that you almost not see . OR A SCUFF MARK ON A PAIR OF HEELS .. I WOULD SCREAM LIKE A SCORN UNGRATEFUL Spoiled Bxxxh.
Good Luck..
Mine bows up in the same spot as well. It doesn't bother me too much but I'm having other issues so mine is going to Acer. Damn micro-HDMI port.
Materials
Mine does the same thing, but I can bend the bezel back. It is IMHO not an assembly issue, the case simply is not as sturdy as it could have been.
Well, I got mine replaced and it is much better, there is a slight edge there but i can live with it, plus no stuck pixel, like my first one.

Just an odd question about the battery cover

Never really noticed because I've had a seidio case on since new, but my cover seems too be a bit too small. The front bezel sticks out about the thickness of a piece of paper. This probably normal just thought I'd ask.
Mine was just like that too. I took apart the phone and found out that my camera wasn't seated properly. May not be the same for you, but it might be something to look into.
Tappin and talkin kindle fire + cm9 lovely
I think this is normal and intended as it protects the screen from pressure. My phone looks like yours as far as you described it and as i wrote it makes sense as to protect the screen.
yeah thats about the best way I can describe it. The battery cover snaps on just fine, but when you feel with your finger it feels like the front part is just a tad bigger. Its not an issue I just never noticed it. I took the batter cover off and everything seems fine.
Here is kinda what I noticed, Im not talking about the gap between the two but how the bezel just protrudes from the cover on the left side.
I have the same thing, it's really annoying. Also, it squeaks -.-
MaXmeOliver said:
Also, it squeaks -.-
Click to expand...
Click to collapse
+1 here
No squeak here.

Iffy Proximity Sensor

Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
bert682 said:
Hi All
Picked up a Nexus 4 a few days ago and only just noticed (as result of a call) that the proximity sensor is reporting that its "blocked" at all times, so the phone things its against my head. I can workaround this by using the "Power button to hang Up" option but at present cannot access any in call features.
When I look under good light the sensor, there are 2 areas so not sure which is the sensor, I can see what looks like a bubble under both. if you imagine what an air pocket looks like under a screen protector thats what it looks like but its behind the glass, perfectly centred. I guess its possible that something has broken here as a result of the drop, the top left corner was the point of impact, does that seem likely?
I got the phone cheap as it had a broke screen so have a new one coming. Its the full screen, glass and digitizer. Does anyone know of the sensor is part of the screen or does it sit behind and then I could be really screwed!
Ta
Click to expand...
Click to collapse
Ok so I did a little more reading and it seems that a gorilla has changed the screen on this phone in the past and he / she has used compound to stick the screen down and some of it has gone around the sensor and the resulting press down on the screen has created a few air pockets.
Looking less forward to changing the screen now as no doubt with my luck the "technician" will have used some crazy heat resistant glue!
Also....missing the speaker grille....funny how you only notice things after you have bought them!
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
Search for proximity sensor fix after screen replacement here on xda. I've found out that if you switch sides of the little rubber /plastic cover that covers the proximity sensor, your problem will be solved. And the light sensor will work with no problems as well.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
It will work for sure, I posted this fix on a YouTube screen replacement guide of octopus glues I think and its confirmed to work from a lot of people. Then if you use a custom rom go to brightness settings while having auto brightness enabled and try changing light sources from dark to very bright places to see the instant lux values you get. If you are not satisfied with the result try custom auto brightness values.
Sent from my Nexus 4 using Tapatalk
bert682 said:
Really?
From reading the thing to do is either make the height of the bushing a little larger, height wise. Or, to increase the diameter of the holes.
I like your fix the best though....no messing about, just rotate.
Will give it a go, thanks!
Click to expand...
Click to collapse
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Planterz said:
Yep, I discovered this "fix" in a random youtube comment (was that you @Sp_Ark?) just a few days ago, and it worked for me. Then I found a thread here that confirmed that this could be a solution (which could have saved me a week of frustration).
If there's actually something on the proximity sensor, then you might be screwed. Well, not really, or $10 from China. The module is a snap-in piece with connector ribbon that also has the headphone jack. The prox sensor is the smaller one on the right side (when looking at the screen).
Disassembly of the Nexus 4 is pretty simple compared to many other smartphones. You'll need a T5 TORX wrench/bit for the screws at the bottom, and a very small Phillips driver for all the screws in the inside. You'll also need a tool to split the 2 halves apart (your screen replacement might have come with tools). You can find a couple videos on youtube, as well as a detailed teardown (pics) at ifixit.com. If you have a hairdryer (or an actual heat gun) you can make the process easier by softening the glue with heat, but it's not absolutely necessary. Just go slowly and be careful when prying the halves apart so you don't flex it too much and break the glass back.
Which screen assembly did you get? You can get it where it's just the LCD and the digitizer, and you can also get it that has the bezel and speaker with it. When I replaced the screen on my N4, I got the whole deal with the bezel and speaker, since it meant less work and fewer things to screw up.
Click to expand...
Click to collapse
I got a "kit" off eBay, [URL="http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT"]http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
That's the full part. The one you've posted is the type I usually go for, they're good quality so far.
bert682 said:
I got a "kit" off eBay, http://www.ebay.co.uk/itm/181144377215?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT so it appears to be the complete screen. Ive watched a few videos but from the pictures it looks like the screen comes with the metal backing so I suspect I dont need to remove the old screen from the casing, thoughts?
Im expecting this to be the screen, bezel, and metal backing so I need to do is connect in my motherboard and all the other components.
Am I off in thinking this?
Click to expand...
Click to collapse
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you), I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other components shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Planterz said:
You made a wise choice, young padawan.
Yeah, that looks to be the entire front assembly, including the screen+digitizer, already installed in the bezel. Also includes the earpiece plus the speaker grill that you're missing. You'll have to swap over the guts, and that's about it. It's easiest to swap the power and volume rocker buttons first since it's a bit harder to get them where they go if you've got the logic board in the way. Just remember that the contact points need to make a ^ rather than a v when you're assembling it with the screen facing down. Tweezers are good to have, especially if they're very long and even better if they're curved. I also recommend doing this over a clean towel to avoid scratching the screen (there'll probably be a film over it too), and the fluffier the towel the better, to catch the tiny screws from flying and disappearing.
Honestly, getting the 2 halves apart is probably the hardest part. They make specialized tools for this, and often the sellers will include them, but it doesn't look like your purchase includes them (mine didn't either). Something plastic is the best choice, since you're less likely to cause cosmetic damage to the plastic (especially the bezel) if you slip (and you will slip). As I said before, GO SLOWLY. Work it apart a little bit at a time, alternate side to side, starting from the bottom. Eventually you'll be able to pull the 2 halves apart.
The battery will be stuck in pretty good and will need to be pried out. If I were you (and a week or so ago, I was you, I'd pop a new battery in while you're at it. At this point in the phone's life, it's probably had at least a few hundred cycles on the battery and has lost 10-20% of its original capacity. The other comments shouldn't be nearly as hard to get out. Just pry in various points until the piece pops out. Do not force anything. Just work it out slowly. After you pop off the piece that covers the USB port, there's the board that has the port, and that can be slightly tricky to get out. Best way I found is to slip something small and flat (screwdriver?) into the port and push up and out, and the board should come out easily.
Thankfully, there's only 3 different screws used, and they're all easily differentiated from each other. There's the 2 T5 TORX that hold the halves together, the 2 very short screws with wide heads that hold the battery in place, and the rest that hold everything else are all identical to each other.
It looks like on your assembly, it comes with its own adhesives. Everywhere there's a blue film, pull it off and there'll be adhesive underneath. I'd recommend leaving the film on over the part where the sensor/headphone jack module goes until you're sure you can stick it in place with the proximity sensor not acting wonky. Download an app (I used Phone Tester) that can read the prox sensor. FYI, as long as everything is in place, and you've attached the battery, you can boot the phone without replacing the back cover, and test the sensor (just depress the center bit of the power button board). You don't need to screw everything in, but you should at least screw and tighten down the few that surround the sensor area. Once you've got it reading properly (best of luck), it's time to put all back together.
You should familiarize yourself with the teardown/reassembly guides out there. Go to ifixit.com and have everything ready to look at. This is the video[/i] that I used to guide me, and I watched it through a few times before I attempted it myself. You should be just fine with your phone after familiarizing yourself, but if you have any specific problems or questions, feel free to ask, and I'm all too happy to help.
Click to expand...
Click to collapse
Awesome, I saw some cheaper screens but that one notes that its LG compliant etc. I bought a set of tools separately so will have all the stuff needed. Didnt think about the battery, will order one as it does make sense!
Thanks for the info, will update as I go.
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Sp_Ark said:
If you want to have a working battery like it used to be before removing it, you have to be very patient and extra careful while trying to remove it. Use some heat for the glue and try with something very thin like a nylon guitar pick. In anyway don't bent the battery and don't start from top. It will be easier to first remove the mother board. Iv already destroyed 4 5 batteries while trying to remove them. Sorry for my English, I hope you understand.
Sent from my Nexus 4 using Tapatalk
Click to expand...
Click to collapse
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
bert682 said:
Yea was extra careful, used a little heat. Someone has definately replaced the screen on the phone before but seems to have been careful enough as no screws missing etc, except the lost the little speaker grille
New screen in and working well. The proximity sensor seems to be working but it reports all or nothing rather than varied. Is this correct?
Click to expand...
Click to collapse
Yeah this is normal.
Sent from my Nexus 4 using Tapatalk
bert682 said:
New screen in and working well.
Click to expand...
Click to collapse
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Planterz said:
Awesome! See, it wasn't too bad, was it? Ifixit gives the N4 a 7/10 for repairability, and that's pretty high for them. After replacing my N4 screen, friend/coworker asked if I could do the same for his HTC One M7 with a completely shattered, yet functional digitizer. I said "HEEEEEEEEEEELL NO!"
Click to expand...
Click to collapse
No, not with the correct tools. I will admit had I not bought the plastic tools, tweezers etc I may have struggled.
The battery was my main concern, its really stuck down, even though this had been replaced before and likely a less tacky glue used it was still tough. Had to use some heat to soften it and the "battery cover" has seen better days. Next thing to replace is that, just for piece of mind.
All in all, pretty nice experience, the phone seems more modular that other phones I have taken apart which is nice.

Categories

Resources