Database Users

i reeallyyyy need somebody's help with unbricking my phone.. please hellpppp!!

alright.. i made a similar post to this before and i came across the wiki...
well i can't view what my SPL or my IPL because as soon as i turn the device on, all that shows is the boot loader screen and displays serial on the top with 0.16-0.90 in red characters on the bottom (I'm not sure what those are)...
here are the only details that i know about my phone:
I DON'T have hard SPL
My Original ROM i was using before was an htc windows mobile 5 rom
The reason that my phone is bricked right now is because the usb cable disconnected in the middle of the flash
I'm using Windows Vista for flashing
Computer won't recognize the phone when on usb
My phone (qtek 9600) can't load the operating system
*EDIT*
THE PHONE IS STUCK ON BOOTLOADER WHEN I TURN IT ON, NOTHING ELSE, BUT THE BOOTLOADER SCRREN DOESN'T SHOW MY SPL AT ALL.
ALSO, MY COMPUTER DOESN'T RECOGNIZE THE PHONE....... MY PHONE HAS A TYPE 2A BRICK
Helping me will be greatly appreciated
come on.. I'm without a phone

Do you have a 2GB or smaller SD card? Copy a rom image to it and rename it HERMIMG.NBH
Turn it on and you might get lucky!

Just make sure its stock rom that was supplied, or the updated WM06 version as the CID should check out then...
vwkess forgot to mention, reset into bootloader, hold power, ok button and reset with stylus. Hold all buttons in until you get to the tri-colour screen. If it works, follow the prompts....
Cheers...

hi,
i think i can hlep.
i had recently bricked my phone with a custom wm6 image, it worked fine for two days and then i reboot, and all i see was the welcome image, nothing else.
so what i did is -
i pressed the hard reset buttons - power + OK + SOFT RESET (Stylus), kept it pressed for 3-4 seconds, the fone rebooted, the screen was full with some colored bricks i connected my fone in USB and on screen i saw USB.
I then again flashed my fone with the working update, it worked perfectly for me, try may be you can get some luck
ps - before doing all these, i turned my fone off by removing the battery, i removed sim card and mmc card as well.
regards

That may work too, but again, try to flash with a stock rom, untick "connect with USB" in activesync and then try.
Make sure you go to boootloader screen, instruction in rajivlodha's post, before you connect to the pc.
Goodluck...

I need some help as well.
I think I may have bricked my phone. It's a rooted htc hero cdma. I'm running cyogenmod on it and it was working fine, until using metamorph to apply some changes to the theme.
I went to reboot, and it now it won't load past the htc screen. Even when i try the key combination to put it into recover mode. I didn't install a nandroid backup, and i'd be fine with just completely wiping my phone. help is appreciated.

HTC HD2 ROM Upgrade Fail on O2

Hello All,
Just wondering if you can help, I have tried to upgrade my HTC HD2. I installed HSPL on the phone, the phone was hacked fine, all went well. I downloaded the Energy Rom, all started to install fine, then it started to load it up for the first time, and then restarted. Now the HD2 won't connect to Active Sync and is just on the O2 Welcome screen and doesn't go any further, any ideas of how I can sort this out please?
Thanks a lot,
Gavin.

flash a compatible radio. check in the first post of your roms thread, the chef will probably recomend one.
power off, hold vol down, tap power keeping vol down, this boots you to bootloader.
when the word 'serial' turns to 'usb' flash the radio.
restart the phone.

Cheers for that managed to sort it.

How to fix an HD2 that Freezes at the splash screen and won't boot

HI,
I just had this problem and I saw that a ton of others had it too. It was where my phone would stop at the windows screen and not boot, and my PC wouldn't read the phone so I couldn't load a new rom or Hard SPL. How I fixed it was by getting my phone into bootloader mode, (the multi colored screen). Here's how to do it.
While phone is Off:
Hold Volume down & press power button
While phone is On
Hold Volume down & press Reset Button (meaning the little yellow button by the battery that you have to press with a pen to soft reset it)
Once your on the bootloader screen, plug your phone into your PC, you will hear the ding that the computer recognized it but your Windows Mobile desktop software will still say your not connected, don't worry about that,, you are connected. After that, just pick whatever rom you want, then just install it like normal. and it works. If your not running a rom, do the same but install hard SPL instead of a ROM.
I hope this helps,
As long as your phone turns on at least to the opening screen there is hope.
kn0t.

i had that problem, my phone was stuck on stock together splash screen, but I just called up tmo and they have sent me a new hd2.

Three words. I LOVE YOU! well not really since I'm not gay ha!
By the way This also works for the HTC Imagio!

can someone help me ! i have the same problem. im not sure i can even open the bootloader menu . when i reset it ,it still goes 3 colours. when i try puting a new rom on it it comes up error 262. tried task29 but still error 262. tried reinstalling activesinc , still error 262,something is telling me to sign into my comp as admin but ... can anyone help?

waigstar said:
can someone help me ! i have the same problem. im not sure i can even open the bootloader menu . when i reset it ,it still goes 3 colours. when i try puting a new rom on it it comes up error 262. tried task29 but still error 262. tried reinstalling activesinc , still error 262,something is telling me to sign into my comp as admin but ... can anyone help?
Click to expand...
Click to collapse
Ok first off what ROM do you have and what SPL does it show when you are in the muticolor bootloader screen? Secound if you are trying to flash a ROM yse right clicking the .exe file and selecting run as adminastrator is a good idea. l

I had the same problem.. what usually helps for me is when it gets stuck.. pull out the battery and give it a solid 15-20 minutes.. and then turn it on and do nothing up until after it has booted

i do the battery thing but i cant go on doing this , i put a little txt or phone call and the phone goes bonkers and heats up,nightmare!
ok on the tri colour screen it says
PBB110 HX-BC
SPL-S.08.0000 8G XE
MICRO(LED) 0X05
MICROP(TOUCH)
SERIAL
AH!! just got into the boatloader screen !! by pressing volume up and down together~! rest it! but i need to wait cos ive pulled the battery again!!!

I am having the same issue. I had a android rom then was finally able to flash via sd the stock rom, but it would just freeze on splash screen when trying to boot. Now when I try to flash rom again it will start and freeze on 1%. Any suggestions?

Now when I try to load rom via usb it starts and then freezes on 1%. Then will say communication error and then when trying to boot phone it says software issue and now I cant even get a rom put back on! Please help lol

stormohio said:
Now when I try to load rom via usb it starts and then freezes on 1%. Then will say communication error and then when trying to boot phone it says software issue and now I cant even get a rom put back on! Please help lol
Click to expand...
Click to collapse
Ok try going to windowsmobile.com/getstarted and download and install the latest version of ActiveSync or Windows Mobile Device Center (WMDC) , wich ever one you have to have for your computer, and install it on your computer as they have updated USB drivers for your HD2.

have you tried loading a rom from the root of your memory card LEOimg.nbh?

i have this problem too...but what is worse is after i went to splash screen and connect my phone to pc, my pc wont detect my hd2...so i cant flash a new rom...
ps : im on stock rom bought this almost 2 years ago if im not mistaken

melodicstealer said:
i have this problem too...but what is worse is after i went to splash screen and connect my phone to pc, my pc wont detect my hd2...so i cant flash a new rom...
ps : im on stock rom bought this almost 2 years ago if im not mistaken
Click to expand...
Click to collapse
You need to put your phone into bootloader then your computer will recognize it. Hold the volume down button down while you power on the phone and the multicolor bootloader will come up. Next connect your HD2 to your computer via your USB cable. Wait for the Serial in the white bar of bootloader changes to USB and then flash. If you go to the device manager of your computer while you see USB on your phone it should say HTC USB Sync if you want to be assured that you have a connection to flash with.

[Q] HD2 cannot turn on...

hi there, im new here and ive been searching on the forum for a long time, but i didnt see any solution for my problem... (or maybe i was blind) so when i was trying to flash back original ROM from bootloader screen through USB, it didnt show my current image version info on the screen, but it did show the image version that im going to upgrade... however, i still let it updated and it said its succeed. but when my phone going to reboot, it stuck on the "stick together" screen... btw, my phone is PB81120 SS-B3 SPL-2.08. HSPL 8G XE. hope someone can help me solve my problem... thanks first :]

Go into bootloader again and connect the device to your PC via usb (should show USB at the the bottom in bootloader) and run the Rom Update Utility again. But first make sure the ROM is compatible with TmoUS Hd2.
I would recommend flashing stock from the bootloader just to be safe.

but i was trying to install T-Mobile_HD2_MR_Software_2.13.531.1 under bootloader, and it still the same... :[

Was that what you origonally tried updating to? Or was it a custom rom you had tried?
Sent from my HTC HD2 using XDA App

that was the latest i tried to updating to, or any different kinds of version of original ROMs... before, i tried to update a custom ROM on it first, but it failed :[ actually, when i first got my phone it was unlocked, so while i was waiting to get the unlock code for it, i decided to install android on it... later on i had successfuly putting android on it, and by that time i got my unlock code too. then i typed it in and my phone just reboot and stuck on the "stick together" screen till now... so i started to look through the forum and found out that most ppl said is to reflash the ROM back to the original one first, and then everything would be alright... but i guess it didnt work on my phone D:

Have you tried a hard reset? (Hold both volume buttons while booting)
Sent from my HTC HD2 using XDA App

yeah... i tried everything :[

hi,
don't worry, your problem is resolvable. (as long as you see something on screen, you are lucky.)
1) When the stick together screen comes, do you see any numbers on left bottom after waiting for some time say 1 min.
if yes, then your problem is missing OS image only.
in this case, take out the battery. after that, keep volume down pressed all the time and insert battery again. press power button, if mobile does not start immediately. please keep volume down button pressed till the time tricolor screen does not come on. after that connect cable to computer and update normally.
2) If you don't see any number, it may mean multiple things, which all are resolvable. (most likely bootloader stuck in another mode.)
in any case, try steps in given in 1 and report back. before reporting back please install mtty on your computer as it is needed to send commands to mobile to get out of this mode.

Try this: http://forum.xda-developers.com/showthread.php?t=668347

[Q] Need Help Fixing My Htc Elf

Hi, I have a HTC Elf0101 and i recently flashed its rom using romutilityuprade.exe and a CID unlocker. I think something went wrong because i cant turn the phone completely on now. When i push the power buttonn, it goes to the htc screen but then turns off automatically before it gets to the windows mobile screen. Also if i connect it back to the computer, activesync doesnt detect it. I can enter bootloader and connect it. Any ideas on how to fix it?
IMEI#: 358472010187127
IPL#: 2.21.0002
SPL#: 1.11.0000