Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
hi guys.....i`m a new member in this forum.
right now, i have problem with my xda exec and need your help badly.
the problem starts with phone gets slower and it seems needed to be "soft reset" as always with the pocket pc.after i did the soft reset, the phone wont turn on.because of it, i try to perform hard reset on my phone, after i pushed 0 to restore factory default, the only message i got is "clearing now" for about 1 sec and after that the exec turn off again. i try this hard reset for several time and the result is still the same.
i also read in this forum how to get into the "boot loader mode" but there is nothing happened with my phone after i perform the 3 button push.
so, PLSSSSS let me know if any of you could solve my problem with my exec.......
btw, i already try to connect my exec with my pc and the message i get is unknown usb device
sorry for u guys who`s already open my thread and thank u so much for trying to help me.i already solve my problem after i read in one of the threads from this forum. thank u so much to this forum, its the greatest mobilephone forum ever .......its true....
Hi guys,
A few months ago I updated from O2s 6.1 to a 6.5 ROM.
Now I want to go back the O2 ROM but the update freezes at 34%. The popup box says it lost connection with the phone.
I tried installing HardSPL but it didnt help. So I tried a hard reset but now I just get a RGB screen with
POLA200 MFG
SPL-2.20.OliNex
CPLD-2
Any suggestions in sorting my problem would be appreciated
Many Thanks
rikpotts said:
Hi guys,
A few months ago I updated from O2s 6.1 to a 6.5 ROM.
Now I want to go back the O2 ROM but the update freezes at 34%. The popup box says it lost connection with the phone.
I tried installing HardSPL but it didnt help. So I tried a hard reset but now I just get a RGB screen with
POLA200 MFG
SPL-2.20.OliNex
CPLD-2
Any suggestions in sorting my problem would be appreciated
Many Thanks
Click to expand...
Click to collapse
First of all check your USB cable... and choose another USB port to connect the cable and try to flash your ROM again
Try this as it has been solved before may help you out
http://forum.xda-developers.com/showthread.php?t=425922
same problem
hi everyone. I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help
Many Thanks for the replies.
I followed the link and i'm confident it will solve my problem. Unfortunately I cannot get mtty to offer "USB" from the dropdown. I remember going round in circles trying to get USB show a few years ago with a SPV C550.
If anyone can help me, that would be great. I'm using Vista. This might be why the steps in both the initial post and replies on the first page don't work for me.
Sorry, i know there so many posts about this problem, but i can't understand it very well, sorry for that.
Here's my problem:
The JasJam that i have says "No GSM", so i tried to fix it, i searched the net for possible solutions, so luckily i found one, well i thought that was the answer, unfortunately i think i downloaded SPL version 7 (which i think is not the right thing to do) then when i was upgrading it, "tricolour bootloader" appears, and then next screen was loading and it is 0%.. then the ERROR #somethng appear, and it stucked on the tricolour bootloader, i tried to fix it again, i tried to upgrade the ROM, SPL, and all because im so hopeless already. Next problem is ActiveSync 4.5 can't detect the jasjam, i tried everything, different PC, laptop and different USB cable as well, i update its .NET framework also, but still there's no connection..
Please HeLp!
I need it badly, please do it step by step, i really really need it please
THANKS IN ADVANCE!
Useful Links:
http://forum.xda-developers.com/showthread.php?t=369434
http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Mike
Hi ladies,
after searching the threads about bootloader mode and activesync I didnt find a working solution for me. I just received a new HD2 with WM and have had a couple of failed boots - I just resetted the phone and started over. This is working more or less 1-2 times before failing the boot mode again.
So i wanted to install magldr and secondly android rom (DHD), but I cant activesync in bootloader mode in the first place. ofc the display beneath the htc logo shows 0% all the time. What can i do? Unfortunately I dont understand what others said to do in this case (RUU, HSPL )
Can some1 pls explain me what to do?
thx and regards
Ladies?
Read this here, if you still don´t understand what to do, re-read.
And please learn about the search function of this forum, the term "bootloader" will guide to at least one more sticky thread with basic tips and hints.
Thx, this was what i was looking for. Fixed it so far.
Thx tictac