Hi everyone!!
First of all, i want to apologize for open this thread but i can't post it in the RAFDROID one.
A few weeks ago i succesfully install the 3.1 version and today i upgraded to 4.0. I followed all the steps to install the ROM... everything goes well until i made the first reboot, well i turned off the device and then i turned on again.
When the phone starts in first place appears the RAFDROID image and then an animation, well my problem starts here it doesn't appear this animation anymore and then, after boot, i get error msg "system process..."
So, i need some help hahaha! What i have to do? Reinstall the rom? Any recommendation?
Thanks in advance!
P.S/ I made the backup and format the SD... but i think i did it wrong the format, 'cos i format all the SD no the ext3 partition...
EDIT:
I found the answer finally! Sorry again!! The thread can be closed!!
u may have to reformat the card with the build instead of the backup itself
if you found a solution write what helped you, in case anybody else has similar problem he won't have to start a new thread.
Related
Hi there
i've had a search through the forums and google, but havent come up with anything...
the isue is, after flashing a new CWM NAND ROM on my HD2, the rom will load perfectly the first time. however the issue is when i try to reboot the phone... it loads through cwm, but hangs on loading the rom...
this has happened on several different rom's, and after several task29/mgldr/cwm re-flashes...
Any ideas?
Cheers
Gav
fatmcgav said:
Hi there
i've had a search through the forums and google, but havent come up with anything...
the isue is, after flashing a new CWM NAND ROM on my HD2, the rom will load perfectly the first time. however the issue is when i try to reboot the phone... it loads through cwm, but hangs on loading the rom...
this has happened on several different rom's, and after several task29/mgldr/cwm re-flashes...
Any ideas?
Cheers
Gav
Click to expand...
Click to collapse
Have you tried doing absolutely nothing after first boot, other than skipping through the setup wizard? What I'm wondering is what you may be installing / doing that could be causing this.
One thing that could help is to run logcat with the phone connected during bootup and you could see what is causing it.
Digital Outcast said:
Have you tried doing absolutely nothing after first boot, other than skipping through the setup wizard? What I'm wondering is what you may be installing / doing that could be causing this.
One thing that could help is to run logcat with the phone connected during bootup and you could see what is causing it.
Click to expand...
Click to collapse
hi there
cheers for the suggestion. i tried a re-flash and skipping the setup wizard, but still the same issue.
attached is a logcat capture.
any help appreciated.
cheers
gav
fatmcgav said:
hi there
cheers for the suggestion. i tried a re-flash and skipping the setup wizard, but still the same issue.
attached is a logcat capture.
any help appreciated.
cheers
gav
Click to expand...
Click to collapse
Yeah, looking at your log, you are definitely in a boot loop. Android keeps restarting after what looks like initializing the audio... looks like some files are missing.
What ROM are you using? Have you applied anything (updates) else at all through CWM other than the ROM? Does the ROM you are using require an SD-EXT partition? Is your SD card in the phone?
Digital Outcast said:
Yeah, looking at your log, you are definitely in a boot loop. Android keeps restarting after what looks like initializing the audio... looks like some files are missing.
What ROM are you using? Have you applied anything (updates) else at all through CWM other than the ROM? Does the ROM you are using require an SD-EXT partition? Is your SD card in the phone?
Click to expand...
Click to collapse
hi
i've been trying "skink_Clean_Desire_v1.1_update_signed" and "NexusHD2-Gingerbread_V2.2_NAND_update"...
SD was partioned and formatted using cwm, with a 1Gb ext partition... SD card is present as am flashing using cwm zip from sd...
cheers
gav
fatmcgav said:
hi
i've been trying "skink_Clean_Desire_v1.1_update_signed" and "NexusHD2-Gingerbread_V2.2_NAND_update"...
SD was partioned and formatted using cwm, with a 1Gb ext partition... SD card is present as am flashing using cwm zip from sd...
cheers
gav
Click to expand...
Click to collapse
Which version of CWM are you using? Is it 1.13? Whatever it is, what size did you flash (the partition layout) for your system partition?
Digital Outcast said:
Which version of CWM are you using? Is it 1.13? Whatever it is, what size did you flash (the partition layout) for your system partition?
Click to expand...
Click to collapse
I'm using the latest versions of Magldr and CWM. I flashed a 250Mb system partition.
Gav
Are you sure that is a large enough partition? Is that what the ROM developer recommends?
Digital Outcast said:
Are you sure that is a large enough partition? Is that what the ROM developer recommends?
Click to expand...
Click to collapse
250 is the recommended size on the cwm thread...
not been able to confirm from the 2 rom threads though...
however i have got a mdj rom whuch flashed succesfully on this size...
fatmcgav said:
250 is the recommended size on the cwm thread...
not been able to confirm from the 2 rom threads though...
however i have got a mdj rom whuch flashed succesfully on this size...
Click to expand...
Click to collapse
just use the "daf" folder that comes with the build once you unzip it.
it has the CWR setting configuration all done ready for the build
just flash it.
My issue is: When phone loads android from NAND (sometimes it freezes in GO GO GO) I can use it some unpredictable time. FE. When I switching Mobile Network on it(after 1-2 it freezes). I even upgraded radio to 2.15. No changes still freezes. Second point is, when I turn off radio module and starting using dev. (FE while playing Angry Birds) it freezes again, with the noise on spekers. In my case I detaching battery and waiting for a while (because if you put battery again after a second) it freezes on GOGOGO again. WTF with device. Maybe it is a physical problem?
Dev is TMOUS HD2 16gb.
ps. When I used Android via SD same freeze always happened only with Angry Birds. In WinMo I didnt recognize such issues. Oooh. One more thing. When I tried to go back to WM 6.5 off.ROM. nothing happened after upgrade. I think my device will always live with Android till the end of the days. Thank you in advance!
Thanks to this forum, i was able to get 7.0.0 stable to run great on my Android. There are a few bugs that seems like the new stable covers. This is my first time updating, I'm sorry that this is extremely rudimentary but I am unsure. Do I just delete the current .zip of 7.0.0 and place the new one in? If so, do i have to boot from sd card again so everything can compile? Or is it a little more complicated?
Did you install it on nand or Sd ?!
i installed it on SD, i can still boot into stock nook.
Anybody help out? Looking to do the update! Just swap .zip files and voila? Or more?
Copy the new update (stable or nightly) to the boot partition of your SD, then insert the SD and do a recovery boot. Verygreen's instructions work fine, I refer to them if I forget!!:
http://forum.xda-developers.com/showthread.php?t=1000957
so i auto updated from 7.0 to 7.02 and now wireless doesn't work....any ideas? thx
ps-i also updated clockwork at the same time (which worked, now 4.2.0.0)
nevermind i rebooted the router
winterps said:
nevermind i rebooted the router
Click to expand...
Click to collapse
Sometimes a simple reboot of your Nook will fix wifi issues, try turning on wifi as soon as it boots up.
Hey guys, I need some quick suggestions if anyone has it. Currently I have a non working phone.
I have been running an ICS NAND rom on my hd2 for a while now, havnt had any issues (a few niggles with the rom, nothing major) so I thought today I would update to the latest version.
I used the hd2toolkit to resize the partition to the biggest size it would allow, then used ad recovery to flash the new .zip to the nand. This is where my problems started, whenever i booted it just showed the boot animation, (I waited over an hour and pulled the battery out and re booted / reflashed a few times).
I found with a differnet rom i tried, pulling out the SD car would allow it to get to the welcome screen, but no screen input was accepted. I thought this was a bit weird but pushed on. I tried a different rom and it stated after flashing that it was optimising applications and looked like it was stuck in a boot loop. I did some reading up about it and found that task29 should help. I ran this but then all the phone would do is show the green HTC on the white background, it wouldnt let me to get into magdlr menu.
I then decided to to a full restore and go back to the wm rom from th HTC site (The australia telstra version), this seemed to flash on fine, but now I can not slide or click buttons in wm, no screen input is accepted. Which is strange as it was doing this in an android rom, as I mentioned previously.
Any ideas on how I can get touch working / get a NAND android rom to work again.
Thanks in advance guys
First verify that you have hspl installed by powering on while holding vol down button to get to bootloader screen
Go back to the hd2 nand toolkit
1.task29
2. Select either cLK repartition or Magldr repartition and select size for your rom (not the maximum size). 200 mb is fine for ics using sdext partition.
3.Select magldr update recovery or cLK install recovery depending on your selection above.
4. Reboot phone by pressing power and holding to get to magldr or power and home button to get to cwm recovery.
5. Install ICS from sd card as before
Thanks for the help, I had to flash a different radio version to get magdlr to boot.
I now have android running of my NAND, but the screen is non-responsive now, as it was yesterday.
I doubt it is hardware related, because I have never had an issue before yesterday when I wanted to change the android version, any ideas how I could get it working?
Make a backup and then repartition again using HD2 toolkit. Maybe you got a bad download or something. Seems simple but it does happen. To me if I didn't know you choose the biggest it would sound like the partition wasn't big enough. Maybe try a cyanogen ROM since it reguires very little partition size and report back if successful.
htccraze said:
Make a backup and then repartition again using HD2 toolkit. Maybe you got a bad download or something. Seems simple but it does happen. To me if I didn't know you choose the biggest it would sound like the partition wasn't big enough. Maybe try a cyanogen ROM since it reguires very little partition size and report back if successful.
Click to expand...
Click to collapse
I have tried two different android roms and the stock wm image from htc's site, all of which the screen doesn't work on. I will have a try with a cyanogen ROM and see if that makes a difference. Thanks
http://forum.xda-developers.com/showthread.php?t=769026
I just tried this rom and still no deal. This is very weird as I haven't had any issues with the screen at all, the phone is still in new physical condition.
Does anyone want to have a stab in the dark, as I really need to use it as a GPS tomorrow and any help would be appreciated.
Tell me what the steps you take to install a new ROM. Do you have MAGLDR or clk? Have you task29 yet? Are you sure your using the right partition? Are you using nand or sd Android?
If all else fails maybe check out this thread to reinstall
MAGLDR and then cwm. I've had problems in the past installing HyperDroid without
wiping my SD card first. Maybe check out this nand ROM instead or Coredroid found in my signature.
htccraze said:
Tell me what the steps you take to install a new ROM. Do you have MAGLDR or clk? Have you task29 yet? Are you sure your using the right partition? Are you using nand or sd Android?
If all else fails maybe check out this thread to reinstall
MAGLDR and then cwm. I've had problems in the past installing HyperDroid without
wiping my SD card first. Maybe check out this nand ROM instead or Coredroid found in my signature.
Click to expand...
Click to collapse
When installing a new rom, I have resized the magdlr partition, then copied the .zip to the sd card, then in ad recovery installed the zip through there. This has worked fine in the past. I followed the videos you have linked and I'm pretty sure I'm doing everything right and yes ive used task29 several times. In AD Recovery every time it states that installation has been successful. I have also formatted my SD card many times.
The ROM you linked, I can find download links on the page, not sure if I'm just missing them.
I just tried an SD card rom, its doing the same thing, no touch input is accepted.
Does NAND roms and SD roms not working imply that it could well be hardware? I just dont understand as it stopped working when I was reflashing yesterday and it was not dropped or roughly handled in anyway during this process.
I am now going to investigate MTTY (for bad blocks) and try reflashing back to original WM again. Please post more suggestions if anyone has them.
Another update: I just restored to default using the method listed below.
http://www.jayceooi.com/2011/08/15/how-to-restore-stock-rom-on-htc-hd2-video/
It took around 40-ish minutes and still no input from the screen, this is seriously frustrating.
WM boots fine and everything, but still no input is accepted.
I'm sorry to say but if your having the same problem with all that then it sounds like the digitizer stopped working. Maybe someone else knows something I don't so I would wait to see if they could help out.
Sent from my HTC HD2 using XDA
Thanks mate, I am not sure why it would have just stopped last night. Appreciate all the help! I'll see if anyone else has any suggestions.
It's not a problem. I do have to admit that it does seem pretty odd the timing of it. Hopefully it's a not the digitizer and someone would be able to point out what might be the cause of everything.
Sent from my HTC HD2 using XDA
This may seem a little crazy, but after having a search online about my issue, it seems that a ribbon going to the screen / digitizer is behind the power button on the HD2s, which apparently can get loose and after a sharp press of the button it started accepting screen input again!
The issue for me now is that when the power button it will stop accepting input again, untill I press it firmly again. I think I may need to open up the phone and check all the connections now.
Hello everyone,
I flashed Hyperdroid about half a year ago and today I decided that it's time for me to update my HD2.
I looked in the Hyperdroid thread, but I couldn't find any tutorial or "This file you need for update" or something like that...
Someone here can help me?
Thank you a lot,
frost-bit
This is the release post of 5.9.0 http://forum.xda-developers.com/showpost.php?p=22959907&postcount=18891
frost-bit said:
Hello everyone,
I flashed Hyperdroid about half a year ago and today I decided that it's time for me to update my HD2.
I looked in the Hyperdroid thread, but I couldn't find any tutorial or "This file you need for update" or something like that...
Someone here can help me?
Thank you a lot,
frost-bit
Click to expand...
Click to collapse
To update your ROM while retaining user data. Follow steps below.
1. In CWM go to mounts and storage
2. Format BOOT and SYSTEM ONLY!!!
3. Clear cache and dalvik cache
3. Press back button
4. Flash the new ROM.zip file from link above or the latest which is 5.10
5. Reboot
Since hyperdroid is a CM7 ROM just like Typhoon, I would assume the update process is the same. Just flash the new updated ROM over the old one and all your data will be retained, although any system apps you've uninstalled will be restored, and the kernel will be restored to the same one which originally came with the ROM if you changed it
Sent from my HTC HD2 using XDA
Hi, so today iv'e flashed my HD2 into NexusHD2, Instalation went fine nd complete till once rom starts up to begin installation of language nd ect.. a window pops in none stop saying.. Unfortunately, the process com.android.phone has stopped, so i'm really stuck in here and just wondering whats so wrong ive done, and any help would be appreciated. thank you.
Btw.., iv'e looked for similar posts but wasnt the same case, so here a new thread that goes in.
You problem lacks of information.
For example:
-Did You flash Nand or DataOnExt,
-And do You have TmoUS or EU htc?
Maybe You had too small cache/partition size.
Strange, i had similar trouble 2 days ago.
I had no troubles with rom, but My phone started to flash itself into lang welcome screen every morning and i had no internal storage after that.
I tried to re-create EXT partition on ClockWorkMod and reflashed dozen of times, but without progress.
Finally I deleted this rom, was one day with useless phone and flashed it again with full wipe/clean flash.
Now it seems to work like a charm, didnt flash for 2nd day so theres a hope for me )
!
Be sure if You set up good settings for cache and system partition as author said.
I rember, that once i flashed 4.2.2 rom with NAND option, although i have only 512mb of ram and NAND option is for HTC T-Mobile US version with 1Gb of ram, so after installation every 5sec i had same error, couldnt do sh1t.
Sorry if i speak wrong or it's nosense, cause it's just too late to think harder
Give me feedback and check every possibility as i mentioned!
Have a good week
Sent from my NexusHD2 using xda app-developers app