Hi all. After trying to unlock my HTC's CID, everything looked fine, until my phone resetted. When I try to turn my phone on, all that comes up on the screen is: Smart Mobility
for about 7secons. Then my phone just turns off. Before I tried to unlock the CID I made a ROM backup. I've tried to flash it back; but this doesn't help. It still just turns off after 7seconds. I got the CID Unlocker from this page:
http://forum.xda-developers.com/showthread.php?t=320155
Does anyone know how I can fix my phone??? I really don't know what to do. Please help...
Just a little search http://forum.xda-developers.com/showthread.php?t=911688&highlight=stuck+smart+mobility
Hi tito12. Thanks alot man. But I still cant find a guide to unbricking my HTC. I used pof's patched 1.11.0000SPL. There is only a guide on how to unbrick your HTC if its HardSPL and not Stock SPL. The only unbricking guide I could find is this one:
http://forum.xda-developers.com/showpost.php?p=3395787&postcount=155
But as I said; its for HardSPL and not StockSPL Any help to where I can find a guide would be very much appreciated.
You can't flash anything when in smart mobility.
Can you get into Bootloader? There are a few methods described in the wiki. If you can so you need an official rom.
There are at least 2 threads dealing with cid unlock (Aman's Uspl and cmonex Hspl), read them carefully, there must be someone who experienced a similar problem. Read this one too http://forum.xda-developers.com/showthread.php?t=372152
Yeah I can still get into bootloader. But where and how do I get an official rom??? I've searched everywhere, but I just cant find a guide to unbricking my HTC....
password BsaD5SeoA
password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
g_cKeyCardSecurityLevel = 0
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
Cmd>ruurun 0
ruurun 0
Cmd>getdevinfo
getdevinfo
HTCSELF010050gUH¥HTCE
Cmd>ResetDevice
ResetDevice
Click to expand...
Click to collapse
Hi tito12. Ok according to this post, my phone IS CID unlocked...
= FF Means that you have a CID LOCKED Device, you most find your original ROM to revive it. So keep reading step B)
= 00 Means that your device stay CID Unlocked yet, so you can try with almost any kind of rom, i suggest that you try DUMPED or COOKED roms first to revice your device.
Click to expand...
Click to collapse
So whats the deal... Do you know why I cant flash custom ROMS or why my phone keeps resetting after "Smart Mobility" ?? I am really confused now...
Hi tito12. Don't worryh. I got it sorted out. But the problem now is everytime I try to flash a rom it gives me this error: Error[270] Image file is corrupted
Any idea how to fix this???? Thanks
Another question: Can I unlock my CID again with HardSPL if my HTC's CID is already unlocked with StockSPL??? I hear HardSPL works better...
I am confused too cause error 270 is cid locked!
When you are in bootloader, what spl and ipl does it display?
IPL : 2.27.0002
SPL: 2.27.0000
Hope you can help me....
Hi tito12. Don't worry; I figured it out. I never did Unlock my CID. So I used HardSPL found HERE
Trust me; HardSPL works the best. And I Flashed the ONYX 6 Rom to my HTC. Works PERFECTLY!! Thanks for the help tito.
EDIT:
Ok so everything worked fine, UNTIL I switched my phone of... And it did the same thing AGAIN. Stuck at the "Smart Mobility" screen. Ok I know for sure that the CID is unlocked and that I successfully flashed the ONYX 6 ROM. But what I don't understand is that everytime I switch my phone of, it gets stuck at the "Smart Mobility" screen....
Does anyone know what is wrong????
Hi, sorry to hear the bad news, I still think you aren't cid unlocked. Pls post the values from your bootloader again. If spl doesn't end with "cmonex" your cid is locked.
IPL: 2.27.0002
SPL: 1.11.0000
(SPL doenst end with cmonex)
Ok so if my CID is still locked. Why could I flash the cooked ROM???
EDIT:
Hi tito12. Ok EVERYTHING is sorted out this time. For sure. I found the problem:
EDIT 06/09/08: Directly upgrading IPL/USPL in one go may or may not work for all of Elf owners (if the Elf is pre-release or old one). If your phone (Elf only) is stuck at Smart mobility screen with IPL 2.26, SPL 2.26, try downgrading the IPL to 1.19 or 1.17.
Click to expand...
Click to collapse
I found it in THIS forum. After updating my IPL to 3.07, I then just followed the steps; and everything works. No more freezing at the Smart Mobility screen! Thanks for all the help
Congratulations
am have this same problem but i cant fix it.....
when i put phone in bootloader i can see this
IPL 1.11.0002
SPL 1.11.0000
PLEASE WHAT FILES DO I NEED TO SOLVE MY PROBLEM...am new with this staff, thankx
wzupfones said:
am have this same problem but i cant fix it.....
when i put phone in bootloader i can see this
IPL 1.11.0002
SPL 1.11.0000
PLEASE WHAT FILES DO I NEED TO SOLVE MY PROBLEM...am new with this staff, thankx
Click to expand...
Click to collapse
Bro Check here....
Related
Brother i am upgrading my device it stoped at 2% now its dead only goes to bootloader show
ipl 1.81.00001
spl 1.81.00001
i master reset but nothing happened i flash all roms on wiki nothing happened always say invalid tool
i need this rom because this has previous this
Rom version 1.8.415.2 wwe
Rom date 11-3-06
Radio 02.71.90
protocol version 4.1.13.31
EXT Rom 1.8.415.102
Thanks in advance who help me in this case
I have another set of that how can i read other set rom and flash in to that set
Was it CID locked? did you buy the phone r did you get it with a subsciption?
oddball1 said:
Was it CID locked? did you buy the phone r did you get it with a subsciption?
Click to expand...
Click to collapse
Not it is Not Cid locked & Also Not Sim Locked.. yes i buy from a shop in pakistan but when i upgrade i get problem
I also have bricked my Herald after upgrading to Aserg but nothing now ,,only green screen and off ...
it was CID locked
from Mobinil Plz Help
zubi1984: i had the same problem.
try mtty.exe (use wiki), and try the commands for it.
if it says something clearly, then you can -somehow- unbrick your device.
if it gives error..
-this happedned to me-
you should bring it to the service, with warranty.
if you are lucky, they will fix it to you without price.
i hope you have warranty, because the man in the service said that i really fuc*ed it up... the new motherboard would have been very expensive.. without warranty
so first of all, calm down, and let's start reading about the upgrade, read a lot, and go to another forums, maybe somebody can help to you unbrick your device
____
my device said:
error 30* invalid upgrade tool (for any roms)
only in bootloader mode running
hard reset failed
reset does not works
no charge lights on charge
mtty.exe error, commands: no answere.
pulyka
Hi pulyka, Can you Please tell me about commands for mtty.exe..what to write inside te command box exactly ,,
any more details about "mtty " would be thankful
for me:
Cmd>info 1
Invalid command : info 1
For a help screen, use command ? or h
Cmd>info 2
Invalid command : info 2
For a help screen, use command ? or h
_____________
this is wrong.
___
read it carefully!
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
try it, but in your own risk..
unfortunately i am not an expert in this..
some people helped me in a hungarian forum.. and they said, my pda is bricked completely:S
if mtty working properly:
sb
I already connect to USB!
Cmd>info 0
GetDeviceInfo=0x00000000
Wizard
Cmd>info 1
GetDeviceInfo=0x00000001
2.21.0000
Cmd>info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0x1EB80000 Bytes
HTCSWIZTMO07 â-r€HTCE
Cmd>info 3
GetDeviceInfo=0x00000003
this is died device:
info1
Invalid command : info1
For a help screen, use command ? or h
Cmd>info 1
GetDeviceInfo=0x00000001
2.24.0000
Cmd>info 0
GetDeviceInfo=0x00000000
Wizard
Cmd>r2sd all
***** user area size = 0x1DE40000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
GetDeviceCID: Error - InitDecoder
GetDeviceCID: Error - InitDecoder
You didn't get the proper security level to download a specific image
Cmd>
pulyka
After trying to upgrade firmware on Herald got brick(?)
When i try to upgrade it by Rom Update Utility - always get 300 error.
I've tried to make Goldcard (tried 3 different sd-cards) with QMAT and typhoonnbfdecode perl script, goldcard always creates succesfully, but
f*** Searching for SD card and moment later tri-color then...
Before that everything was o.k...
When i turn it on there is green display...
Any ideas guys? any suggestions??? what mistakes could i made?
mtty says
SDInit---
SDInit OK
Unlimited time!
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = 0
....
Cmd>getdevinfo
GetDeviceCID: Error - InitDecoder
So, now I cant get anything working in my P4350 except the bootloader mode.
The way I got here:
Installed many roms, trying to find the best for me. After some time, even the most stable rom was not stable, all of them crashed, freezed, rebooted after about 1 day usage. (With and without SD card, and no apps installed).
So I decided to remove hardspl and do the whole thing again. I downloaded Aserg-Remove-Hard-Spl pack, and run it. After the second step the phone was not completly blank, I saw the console staying at the "praying ..." text (without backlight), and the phone didnt responded for any buttons or touch. So here came the third step, the RUU, but it gave me error 260, that it cant find my device. (How would this, since the activesync was not connected?)
So i couldnt do anything, I soft reseted the phone, but it wont turned on, or it did but the screen left blank. - like no rom were installed. I tried to press the camera, and the RGB screen came up, saying IPL 4.14.0001 and SPL 4.70 Yang.
Tried to hard reset, but when I pressed send, it said fail.
Tried to update at this position with RUU, but its need activesync so it gave me the same error. Tried to install 3 different roms from 2 differenct SD Cards (that worked before), and It checks the Card, the the RGB screen comes up (like no rom would be on the SD card).
Created a GoldCard, and installed the official ROM. The "Checking SD Card" text stays here for 5 secs, then the RGB screen comes up.. wtf?
Same with heradiag.nbh
Now tried again the Hard reset, it said succesfull, but when it tries to boot I just get a green to black gardient image, something like this: http://www.cylekx.net/help/tutorial_assets/images/byte ramp and green gradient.jpg (but rotated), and nothing else happens.
Any ideas to get the device back to life?
Maybe there are some hardware malfunction inside the phone?
Thanks, and sorry if I posted this to a wrong thread. (was not sure where it should go)
Just got a WhiteScreen crash at the "Checking SD Contents" screen.. It cant be software problem i guess.
Cmd>getdevinfo
GetDeviceCID: Error - InitDecoder
HTCSHTCE
Cmd>ls
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
start download
==CreateFile err==nb0 Sync bytes error(0) 6B != 42
Error : DownloadImage return error (code = 0xFFFFFFFF)
While your phone is in Bootloader mode, install the original ROM with the RUU. All Heralds (P4350) and Atlas'(Wing P4351) can be flashed while on the bootloader screen. Just disregard the step on the RUU that says to make sure your phone is connected to ActiveSync. Also if you have downloaded the whole RUU for the Original ROM, you have to edit the .EXE file to remove the .SPL file that is inside. You can use 7-Zip to get inside of the .EXE file. If not, then just install the ROM as you normally would. You will not need a SD card to install this. Let us know what happens. EVERYONE: if I have forgotten to mention something, please add.
baronmxc said:
While your phone is in Bootloader mode, install the original ROM with the RUU. All Heralds (P4350) and Atlas'(Wing P4351) can be flashed while on the bootloader screen. Just disregard the step on the RUU that says to make sure your phone is connected to ActiveSync. Also if you have downloaded the whole RUU for the Original ROM, you have to edit the .EXE file to remove the .SPL file that is inside. You can use 7-Zip to get inside of the .EXE file. If not, then just install the ROM as you normally would. You will not need a SD card to install this. Let us know what happens. EVERYONE: if I have forgotten to mention something, please add.
Click to expand...
Click to collapse
Hah, i was so unlucky A chip on the motherboard burnt, so if u plugged in the USB it crashed immadiatelly, no wonder why the PC couldnt recognise it..
But still have a problem. Tried to flash the original shipped rom, and another costum rom but both said INVALID MODEL ID.
So what now?
thanks
Cmd>getdevinfo
GetDeviceCID: Error - InitDecoder
HTCSHTCE
Cmd>ls
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
start download
==CreateFile err==nb0 Sync bytes error(0) 6B != 42
Error : DownloadImage return error (code = 0xFFFFFFFF)
Cmd>set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
PL_SDSetSlotNumber() - MPUIO_SDIF_SEL1=0, MPUIO_SD_IF_SEL=0
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SD Ver2.00: Low Capacity
SD clock to 24MHz
***** user area size = 0x79A00000 Bytes
SDInit---
SDInit OK
Unlimited time!
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = 0
HTCE
More Info:
Now i can connect with MTTY and write commands in the bootloader. With this SPL version most commands i found doesnt work, but I got some information about my phones status: the GoldCard's security level is 0, thats correct. The problem is with the CID: GetDeviceCID: Error - InitDecode
I think the problem is this, since it cant get the CID, cant verify the rom matches .
I can write things with mtty into ram or storage, is it possible to write the whole rom directly to the devices boot dir?
CheeseDave said:
Hah, i was so unlucky A chip on the motherboard burnt, so if u plugged in the USB it crashed immadiatelly, no wonder why the PC couldnt recognise it..
But still have a problem. Tried to flash the original shipped rom, and another costum rom but both said INVALID MODEL ID.
So what now?
thanks
More Info:
Now i can connect with MTTY and write commands in the bootloader. With this SPL version most commands i found doesnt work, but I got some information about my phones status: the GoldCard's security level is 0, thats correct. The problem is with the CID: GetDeviceCID: Error - InitDecode
I think the problem is this, since it cant get the CID, cant verify the rom matches .
I can write things with mtty into ram or storage, is it possible to write the whole rom directly to the devices boot dir?
Click to expand...
Click to collapse
a INVALID MODEL ID error occurs when you use the wrong RUU/ROM for a phone. Heralds must use the Herald RUU and Wings must use the Wing RUU.
Herald RUU (P4350) <- English version is the 3rd link.
T-Mobile Wing [Atlas](P4351) RUU <- Phone Number and IMEI Required
T-Mobile Wing [Atlas](P4351) RUU<- Phone Number and IMEI NOT Required however I believe that this is an older Windows 6.0 Build
If you want to keep your phone hard spl'd, you need to modify the EXE of the RUU and erase the SPL.nbh file.
As far as writing the ROM directly, that is out of my expertise. Someone else will have to answer that.
baronmxc said:
a INVALID MODEL ID error occurs when you use the wrong RUU/ROM for a phone. Heralds must use the Herald RUU and Wings must use the Wing RUU.
Herald RUU (P4350) <- English version is the 3rd link.
T-Mobile Wing [Atlas](P4351) RUU <- Phone Number and IMEI Required
T-Mobile Wing [Atlas](P4351) RUU<- Phone Number and IMEI NOT Required however I believe that this is an older Windows 6.0 Build
If you want to keep your phone hard spl'd, you need to modify the EXE of the RUU and erase the SPL.nbh file.
As far as writing the ROM directly, that is out of my expertise. Someone else will have to answer that.
Click to expand...
Click to collapse
Thanks for your help, but as i said my device ID is messed up with the USPL process... "GetDeviceCID: Error - InitDecoder" None of the RUUs works.
Waiting for the directly-writing method, or i'll have to replace the storage at the mainboard... (wont be cheap).
Hi Guys,
I tried to upgrade my artemis (Windows 5 Swisscom) and while upgrading I got error message:
This operation will delete
all your personal data, and
reset all settings to
manufacturer default.
Press Send to restore
manufacturer default,
or press other keys to
cancel.
Click to expand...
Click to collapse
I pressed send button and nothing happens. wait some minutes... Pressed again send button and nothing happens. After 10 minutes a press reset button.
Now I cannot switch on the phone. I can only presse right and left software key + reset button to get the message above. If I press send button, i got for a second 2 new lines:
Format Fat partition
Format is failed
Click to expand...
Click to collapse
then the display switched to a green colour gradient with red signs
IPL 1.14.0001
SPL 1.14.0000
Click to expand...
Click to collapse
Connection to active sync is not possible (nothin happens) and I don't know hot to use MTTY to enter bootloader via PC. I spent 3 hours reading threads in this and other forums, but got no solution.
Can anyone help?
...
The bootloader is accessed by pressing and holding the Power and Record button, using the stylus at the same time press the SOFTRESET/stylus button... keep both buttons pressed after releasing the softreset/stylus button.
when you have it in bootloader ''(a green colour gradient with red signs.lol)'' you can just run the RUU (rom update utility) on your pc, no need for mtty.
(Windows 5 Swisscom) - i suggest you download this and flash with this first because its the only way to revive it if your SPL is:
1.14.0000 and your stuck on bootloader.
look for it at..
http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
......................................................................................
when you have done that its time to do Update SPL on your device..
connect to activesync
run dos window on pc
soft rest when the RUU window appears on pc
connect to activesync
RUU - click through and flash Uspl cmon
SPL: 1.11.cmom = its done
USPL CMON:
http://forum.xda-developers.com/attachment.php?attachmentid=41246&d=1181558635
now download any artemis/p3300 rom and flash.
Hi raving_nanza,
yes, I pressed and hold the record and power button while using sft reset button and was able to enter bootloader (it is red,green,blue,white).
On your hyperlink, I found no Swisscom ROM and a lot of dead links or rapidshare was overloaded, so I tried the swedish one (yes I speak a little bit swedish).
-- HTC_P3300_SVE_3.13.413.1_4.1.13.44_02.94.90_Ship_R.exe --
Now I connect device to USB and "USB" is shown on display, but I was not able to connect via Active Sync. So I restart my PC. After restart, I was NOT able to enter bootloader again :-(
I pressed record, power and soft reset in right way but nothing happens...
What is wrong? For a short time it seems to working, but now.... nothing!
pls help.
thanks in advance
...
for it to work you must find the original rom that is for the device..
its not worked because it needs to be the correct rom your flashing..
(your phone is a brick untill you find the original rom)
these are yours..
IPL 1.14.0001
SPL 1.14.0000
is there anything else displayed?
looks like your going to have to have a night in looking for the rom on google.lol
when i have some time tomorrow ill help you search...
as for bootloader, dont worry about that untill you get the original rom..
...
i know how to use mtty, so no worries...
(unless you cant find rom then your stuck until someone posts a link or uploads it.lol)
* hopefully find rom
* flash through bootloader or mtty
* flash Uspl cmon
* flash NEW rom
* DONE
you could email the swisscom helpcenter and ask if they still have an original rom for the p3300 available. maybe u are lucky
mvenneker said:
you could email the swisscom helpcenter and ask if they still have an original rom for the p3300 available. maybe u are lucky
Click to expand...
Click to collapse
I sent a mail to swisscom. Maybe it works. Thanks.
raving_nanza said:
for it to work you must find the original rom that is for the device..
its not worked because it needs to be the correct rom your flashing..
(your phone is a brick untill you find the original rom)
these are yours..
IPL 1.14.0001
SPL 1.14.0000
Click to expand...
Click to collapse
How should I search in Google the correct ROM? Is it not possible the flash to any ROM I found in this forum?
raving_nanza said:
is there anything else displayed?
Click to expand...
Click to collapse
Not really. After connecting USB calble, on bottom of display "USB" is showing, but no active sync was possible.
Thanks for your help
dj-digger said:
How should I search in Google the correct ROM? Is it not possible the flash to any ROM I found in this forum?
Click to expand...
Click to collapse
If your phone is bricked, and it looks that way, then the only rom to repair your device is the original rom supplied by the manufacturer or the telecomprovider of your phone, in your case, a windows mobile 5.0 version from Swisscom. or else the original stock-rom 5.0 from HTC.
neither of them are available atm on XDA-dev website unfortunately
Hi!
I'm happy you speak some swedish,but Swisscom is in Switzerland,not in Sweden.
Official languages in Switzerland:german,french,italian.
Your device is CID locked to Swisscom,so you can't flash a different ROM on the normal way.
I can help you with the solution,called Goldcard:
http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard
Make a Goldcard,flash your device with a shipped ROM and it will be fine.In this case the language of the ROM doesn't matter.
BR
Szig
scootie said:
Hi!
I'm happy you speak some swedish,but Swisscom is in Switzerland,not in Sweden.
Official languages in Switzerland:german,french,italian.
Your device is CID locked to Swisscom,so you can't flash a different ROM on the normal way.
I can help you with the solution,called Goldcard:
http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard
Make a Goldcard,flash your device with a shipped ROM and it will be fine.In this case the language of the ROM doesn't matter.
BR
Szig
Click to expand...
Click to collapse
Hi I tried the Goldcard method but failed while finding out my CID. The MTTY showns some errors:
Code:
Cmd>password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
[COLOR="Red"][B]CMD55 failed[/B][/COLOR]
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
[B][COLOR="Red"]CMD55 failed
GetDeviceCID: Error - InitDecoder[/COLOR][/B]
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
[B][COLOR="Red"]RUURUN fail[/COLOR][/B]
HTCSF
Cmd>ruurun 0
Cmd>ResetDevice
In the LOG of SnoopyPro, I found no information Like ELF... or HTC_.
I registered one more issue: In the manual to get the ELF said:
5.- Turn on your DEVICE in BOOTLOADER MODE then connect your USB cable
And the screen in this manual shows the Bootloader with "RUU" in the top right corner. This is not shown on my Device.
So have anyone an idea, how the USPL and Flashing my Artemis?
Does no one have an idea? I can enter the bootloader (sometimes), but I got no Active Sync Connection...
Hi, everyone! I've forgotten password on my Blackstone. I need phonebook from it, so hardreset and reflashing is not decision for me. Does anybody know how can I get my phonebook? I see the only way is to dump all memory from the Blackstone, but I have no any experience. Please help me!
MOD EDIT - I've moved this thread to General Discussion forum as you're more likely to get an answer there as it's the Q&A forum
I'm trying to execute command
set 1e 1
rbmc c:\temp\os.bin OS
MTTY writes "Need password"
Who knows password?
Bootloader password is "BsaD5SeoA"
Here is the log of mtty:
Code:
Cmd>password BsaD5SeoA
password BsaD5SeoA
Pass.
HTCST ЪИТHTCE
Cmd>set 1e 1
set 1e 1
Cmd>rbmc os.bin OS
rbmc os.bin OS
Fixed new dwPSImageSize = 0x15080000
GetExtRomData+(): *pszPathName=temp.nb, dwStartAddress=50420000, dwLength=85E5600
:F=temp.nb
:A=50420000
:L=085E5600
:rbmc=
It creates temp.nb with size 1031 bytes, but there is no os.bin. What is wrong?
does the command "r2sd" work on Blackstone? Is there any other commands to read data from Blackstone in bootloader mode?