Related
Everything was absolutely fine earlier this afternoon (then the phone got a bit hot while riding in my car) and now, It is not being recognized by active sync or any power sources. The amber light doesn't light. It has happened before but then "fixed" itself. Anyone have any experience with this? This has happened both with the original ROM and the AP rom I am running, so I don't know that it is a software based problem. Any ideas? (Yes, I have it turned off, I have pulled the battery out as well, the USB feels no different than it did before).
-Will
Are you under warranty? Since this sounds like a recurring hardware issue I'd get it replaced. I've never had this issue, even when I left it on the dash of my car for an hour this summer, directly in the sun (by accident). The screen protector bubbled up and it was almost too hot to hold, but it started right up and hasn't had any problems.
Have you tried a hard reset?
Definitely no warranty (this is one that I did the screen replacement on and worked flawlessly for over a week with no problems. It did this before the screen was broken as well.) I noticed that it does feel a bit loose (the USB) so I am opening it up and going to check the solders. I know I'm crazy for doing this but it's out of warranty and it is already broken, so.... why not? And yes, I've done a hard reset and it still is giving me fits.
-Will
well....
All solder joints seem good, no inordinate resistance, nothing out of the ordinary... the problem is further up the stream I am guessing.... so right now, it looks like I'm down my Advantage. May just end up selling it off for parts and getting a Diamond or some such for a replacement (can't afford another X75xx series phone right now...)... Brand new screen on it, and everything worked fine for a week but I think something in my car fried it... because my S621 died the same way recently... and my Asus PND fried as well....and all of them had one common thread. Being plugged in to my car for recharging purposes most of the time.
-Will
hooty said:
All solder joints seem good, no inordinate resistance, nothing out of the ordinary... the problem is further up the stream I am guessing.... so right now, it looks like I'm down my Advantage. May just end up selling it off for parts and getting a Diamond or some such for a replacement (can't afford another X75xx series phone right now...)... Brand new screen on it, and everything worked fine for a week but I think something in my car fried it... because my S621 died the same way recently... and my Asus PND fried as well....and all of them had one common thread. Being plugged in to my car for recharging purposes most of the time.
-Will
Click to expand...
Click to collapse
I sent you a PM. interested in it for parts (I also posted a thread about looking for parts)
Hi, I come on here quite a lot for information as it's an amazing resource! This time however, I'm attempting to give something back!
I experienced the "black screen on slide out" on Monday. Phone completely screwed. I've also had a few droppages and had it apart once before so there's no way warranty is gonna help!
I stripped it down and soon discovered what it is that actually fails on the ribbon. The coating had worn through due to rubbing on something during the slide out / in process. it had been playing up for a while, probably due to shorting out on the metal case, but now the tracks (aluminium?) had worn right down.....
In pic 1 i've circled the worn area. The shiny section is where i'd tried taping over it to prevent shorting, before i realised the tracks were gone.
Got an almost new one off ebay for 15 quid and, realising it was going to happen again, came up with a solution that, so far, looks like it will work....
A while back I bought some "anti rattle felt" for my car's dashboard - really thin and strong self adhesive felt to prevent squeaking joins between dash sections. I cut a piece of this and stuck it to the new ribbon. Once this stuff is on it's well stuck, by the way!
See pic 2 for the modded ribbon cable.
On reassembly everything is working just fine so far! Here's hoping that it lasts longer than 6 months this time!
Just need a new casing now as mine is decidedly second hand!
Hope this turns out to be of use to someone!
cool story bro
when i took apart my xperia to replace the housing this seemed like a really weak point in the device. glad to see someone who has had the problem has been able to fix it
Why does the screen go black?
Hi,
When the coating wears off the ribbon cable it exposes the tracks in it. when you slide the keyboard out the exposed tracks short out on the metal casing and the screen loses it's input signal.
thats whats happened on mine at least and i presume quite a few others?
HTH!
Update:
That's interesting: My phone was also losing signal with the keyboard out, and occasionally while closed up as well. It would just randomly drop to "no signal" for a few seconds.
It hasn't done it since replacing the ribbon cable.....could be coincidental of course.
I'm having the same problem
It just started a week ago and I got the phone in January off of ebay. I'm new to opening up the phone so could anyone help me find the correct tools or have a link to a site with pictured instructions?
I noticed that the sliding mechanism started to go loose about 4-5 months ago but didn't expect the screen not respond in landscape mode. I have yet to see the other symptoms you all are referring to. I would like to fix this before it get worse.
In mine case it went totaly black after one week of this problem... You have all the instruction on youtube, there is where i looked. For tools you can be inovative, but the exactly right ones come with housings from ebay, it is only 15EUR, and i bet you have some cracks so it wouldn't hurt replacing. That is what i did, along with ordering new sliding mechanizm, and new ribbon cable.
I am open for ideas to prevent my ribbon cable from being cut at it weakest point again.
I'm assuming my flex ribbon went bad yesterday, since sliding the keypad out causes my screen to shut off.
Already ordered a cable off ebay and will attempt to replace it myself :O
Replaced my flex ribbon cable with one I bought on eBay. The screen doesn't turn on at all now, which leads me to believe the cable I was sent is defective. Put the old one back in and it works okay, less landscape mode. ughhh what a pain.
great tips! my input is I bought a case off of ebay that was ~60$ and everything actually fit fine for me...so I wouldn't discount every seller but you do get what you pay for, the 15$ cases are probablly the ones that will give you problems
I working in a mobilephone repair center if anyone need help drop me a priv... i able to get 2nd hand or even brand new components
Replaced the flex ribbon cable -
I got my flex ribbon cable a few weeks ago and took it to my local repair shop. They replaced it but the LCD screen/optical joystick receives no power. The touchscreen and everything else on the phone works just fine now. I thought it was a defective item so it was exchanged with a new one.
Got the repair shop to replace it again and the outcome still remains the same as the first.
Theres no light coming from the screen nor the side illumination.
I just told the repair shop to just place the original back in for the mean time.
Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power botton.
Could it be defective a batch that the seller was sending out? or the repair shop's mistake and is playing dumb so they do not have to admint fault?
Hopefully there's an easy fix to this problem.
-Also I did inspect the ribbon before and after the repair. looks new as the OEm
Can anybody help me out with this new problem after replacing the cable -
perhaps you should try a hard reset. Ive had problems in the past where the optical joystick and the illuminators did not work, and that worked for me.
On the other hand, the top illuminators are on the same piece of hardware as the flex cable that was replaced, so a faulty flex cable is possible. The bottom illuminators are on the circuit board that the optical joystick attaches to, separate but connected to the flex cable.
Ive recently replaced my flex cable and touchscreen. The experience i had with the faulty touch screen was that it appeared to receive no power, but was in fact displaying a dark backlit illumination that could only be seen in the dark. At the same time however, the screen did not display anything. I'm not sure if this is similar to your experience, but if so then your touchscreen would need to be replaced.
ive done all repairs on the xperia myself, and one thing ive discovered is if something doesnt work right after a repair, simply disassembling it and reassembling it to make sure all the connections are properly done has worked for me in the past.
"Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power button."
Now when you say the power button, do you mean that a red light appears under it?
I dont know if i can come to a conclusion or that i can help (or have helped) you come to a conclusion, but i can only assure you that the xperia acts out in strange and weird ways.
Good Luck!
Tags
Dismantle / Disassemble Sony Ericson Xperia X1
http://www.ifixit.com/Teardown/Sony-Ericsson-XPERIA-X1/788/1
http://www.formymobile.co.uk/xperiadisassembly.php
http://www.youtube.com/watch?v=AWDurQrRt-Y (REAR)
http://www.youtube.com/watch?v=iyGUbxFqvyc&feature=related (FRONT)
http://www.youtube.com/watch?v=elgC8hwHfYQ&feature=related
For info.
Mike
Thanks for the links. I've tried the hardreset and restoring the original rom but the issue is still there. It's really bugging me that everything works but the LCD screen. I'm currently using MyMobiler to use my phone. The touch screen works fine and so does the soft keys. Just no power for the lights. I might just give up and wait for another phone that catches my eye and then tinker with the xperia myself. but if anyone got a solution or want me to test something then I'll give it a try.
My warranty is no longer affective so I'll use my phone as a tester to help others with any problems.
TRIONDAVE, how's your Xperia running now with the cable mod that you did? Its been 6 months since you created the thread. I hope you're still around.
My Xperia X1 works nearly fine, except for the keyboard issues, so I'm thinking of opening it up. If your Ribbon mod helped I might just do it too once I've got it opened. Mine has a MOUNTain of cracks though, and the battery compartment itself is cracked on both side enough to make the compartment CURVED. Hence the Battery cover doesn't sit well.
I'm looking around for broken Xperias which I might be able to use to change the internal cracked casing. Lets see.
DatDereX1 said:
cool story bro
Click to expand...
Click to collapse
My thoughts exactly.
Hello guys, I am in need of real help over here!
Its just that Ive replaced my ribbon cable, the old one got screwd up.
However I got done for 10 minutes ago, tried to start up the phone.. without success :,(
The ribbon cable doesnt have anything to do with the start up, only the screen am I correct? Cause I cannot even start my phone..
Ive connected the charger, but when I remove the battery it shows a red light, meaning no battery, correct?
So what may the problem be exactly? Maybe the battery is all dead, or?
PLEASE HELP!
for the people with ribbon failures how long have you had the phone before it occurred ? im just interested on the cables lifespan.
mine is fine so far but i have noticed the slider is flimsy and rocks left and right.
Hello Gents and Gals. I am trying to fix my friends HD2, I flashed his ROM with Energy couple of months ago and all was working fine. He gave the phone back to me saying that it is locked.
I tried unlocking the phone but it seems that the screen is unresponsive, so I flashed it again by going into the boot loader screen "Volume Up + Power Button". The phone stated that it is starting for the first time but the screen was still unresponsive. Any ideas on how to fix this issue? Or do I need to tell him to send the phone back to HTC for repairs?
Sounds like the touch screen died ....
Time for a repair ..
Also this really should have been posted in general , as it is not a ROM release , just an FYI
Aww okay. I'll let him know. Thanks.
I'll post like this in General next time. Tks.
HI, I have now the same problem after ROM Flashed, did you solve the problem by yourself, or really the touch screen died.
Rgds
Same thing with me. I ordered new digitizer+LCD and changed them, but the screen is still unresponsive. Other ROM didn't help.
Some advices?
i seen this happen with several phones, reflash to stock and send to HTC they will repair it for free.
I have same problem,yet my phone was bought 18 months ago...worked perfectly until now.
Can a touch screen get defective after normal usage ?
alexandruvlad said:
I have same problem,yet my phone was bought 18 months ago...worked perfectly until now.
Can a touch screen get defective after normal usage ?
Click to expand...
Click to collapse
Yes it can, if your touch functionality of your HD2 has stopped working then your digitizer has probably went out.
T-Macgnolia said:
Yes it can, if your touch functionality of your HD2 has stopped working then your digitizer has probably went out.
Click to expand...
Click to collapse
Yeah,that's what i thought too - but i read some situations where replaced LCD + Digitizers didn't solve this problem.....
alexandruvlad said:
Yeah,that's what i thought too - but i read some situations where replaced LCD + Digitizers didn't solve this problem.....
Click to expand...
Click to collapse
This is usually due to the replacement components not being properly installed. Also when one is working with the internals they have to be very careful as some of the internals are very easy to break without you even knowing you did. So the cases you spec of are more than likely not because it was not the Digitizer or LCD was not the problem, but human error.
i fixed mine and it didnt cost me
the unresponsive screen maybe the digitizer buts its more likey the end call button, believe it or not dirt can get behind the contact or because the back button is next to we use the far edge of the end call button thus leading to bending the contact, when any of this happens your screen will be unresponsive
you can either take it to a shop and pay for a new screen and digitizer or take it apart and clean the contacts
go to ifixit for step by step guides
hope that helps
Intrigued
dgr1983 said:
... buts its more likey the end call button, believe it or not dirt can get behind the contact or because the back button is next to we use the far edge of the end call button thus leading to bending the contact, when any of this happens your screen will be unresponsive
Click to expand...
Click to collapse
I have no idea what are you talking about, that doesn't make sense, as far as I know is no direct relation between END button and (non-working/responding) touchscreen: you may even disconnect/replace bottom buttons ribbon/flex from motherboard and touchscreen will work if OK(or not, if defective).
Is there anybody who can confirm this(or not)?
3 weeks ago I had a LCD/digitizer replaced (cracked screen, but was still working) all was great till 2 days ago. Screen stopped working - took it back to the place I had replace the screen and they tried 3 brand new screens and still no go. Ended up being my main board - luckily I had a spare HD2 and they pulled that board and all is well again.
Believe it or not your LCD/digitizer might be fine - find someone or a way to test main board would be where I would start after the last 3 days.
Good luck
PS - I did NOT try the end button idea prior to the repair.
Zergalot
zergalot said:
3 weeks ago I had a LCD/digitizer replaced (cracked screen, but was still working) all was great till 2 days ago. Screen stopped working - took it back to the place I had replace the screen and they tried 3 brand new screens and still no go. Ended up being my main board - luckily I had a spare HD2 and they pulled that board and all is well again.
Believe it or not your LCD/digitizer might be fine - find someone or a way to test main board would be where I would start after the last 3 days.
Good luck
PS - I did NOT try the end button idea prior to the repair.
Zergalot
Click to expand...
Click to collapse
If still in your possession, I would be interested to buy the motherboard you just replaced!
PM me if interested!
htc hd2 screen died
I also have a 2009 htc hd2 on which screen does not work.
I'd like to know if it's
- a common problem
- is it possible that it's a software (flashing) issue
- can it be replaced and for how much
martinmartiini said:
I also have a 2009 htc hd2 on which screen does not work.
I'd like to know if it's
- a common problem
- is it possible that it's a software (flashing) issue
- can it be replaced and for how much
Click to expand...
Click to collapse
From my own experience :
1. It's a common issue, there are hundreds of reports in this forum and I read them all because I had the same problem some months ago
2. Probably not. It's generally hardware-related and often the digitizer (touch responsive screen) . Brief explanation : There's a flaw in the design of the HD2, the thin cable wiring the digitizer to the motherboard, is just below the power button. After some extensive use of your powerbutton, it might happen that the power button touches the cable and cause some kind of shortcut in it which makes the digitizer unresponsive to the motherboard.
3. I replaced mine here : http://www.htcphonerepairs.co.uk/ . Fast repair, secure shipping to Belgium, good price and excellent customer support. (Sounds like advertizing but I swear to be only a happy customer )
There are also multiple videos on youtube explaining how replacing the digitizer yourself if you dare !
Also, I read answers saying that you can somewhat "play" with your buttons (especially the power one) to turnaround the problem. That's correct, BUT it's absolutely inevitable that the problem with come back again if you use the buttons, and you'll have to force more and more to unblock again and repeat again and a again... and that will damage your button bar.
I did this during almost 2 months and that put down all my buttons and now they are really close to the chassis which is very annoying. If only I knew it before I would have replaced the digitizer directly !
For 6 months with my new digitizer + using ICS with soft buttons, I have no problem at all !
bib*oops said:
I have no idea what are you talking about, that doesn't make sense, as far as I know is no direct relation between END button and (non-working/responding) touchscreen: you may even disconnect/replace bottom buttons ribbon/flex from motherboard and touchscreen will work if OK(or not, if defective).
Is there anybody who can confirm this(or not)?
Click to expand...
Click to collapse
Just because this dude has "no idea" it doesn't mean he knows it better.
It IS the END button that gets pressed too often and at some point it begins to mess with the digitizer connection. It can be dirt. It can just be the cable came lose and needs tightening, it can be wear-out.
whatever it is, it is caused by the end-key being too close to the connector cable.
If you guys only searched for this on the HD2 Forums before posting this Thread hat not been necessary. It is the most well known design flaw of the HD2 and as such well documented and commented here.
Sneakyghost said:
Just because this dude has "no idea" it doesn't mean he knows it better.
It IS the END button that gets pressed too often and at some point it begins to mess with the digitizer connection. It can be dirt. It can just be the cable came lose and needs tightening, it can be wear-out.
whatever it is, it is caused by the end-key being too close to the connector cable.
If you guys only searched for this on the HD2 Forums before posting this Thread hat not been necessary. It is the most well known design flaw of the HD2 and as such well documented and commented here.
Click to expand...
Click to collapse
This is truth. Save yourself some time and frustration and repair it or get it repaired. It's a great phone.
Sneakyghost said:
Just because this dude has "no idea" it doesn't mean he knows it better.
It IS the END button that gets pressed too often and at some point it begins to mess with the digitizer connection. It can be dirt. It can just be the cable came lose and needs tightening, it can be wear-out.
whatever it is, it is caused by the end-key being too close to the connector cable.
If you guys only searched for this on the HD2 Forums before posting this Thread hat not been necessary. It is the most well known design flaw of the HD2 and as such well documented and commented here.
Click to expand...
Click to collapse
You didn't get it right or at all:
END key may determine touchscreen failure along the time(being the CAUSE! of this), but the EFFECT is an unusable touchscreen, which cannot be repaired in any other way than replacing it(the touchscreen!!, I mean).
Any other attempt to repair, clean, bend, press, cut or whatever WILL NOT FIX an already faulty touchscreen (even caused by END button excessive or not usage) and who thinks otherwise, no problem with me: SWEET DREAMS!
You sound like my comment hurt you. Sorry if it did. I'm not one hundred percent sure that this issue can be fixed without replacing the screen, yet fairly certain. I've now disassembled two HD2 and couldn't quite find the precise spot where the damage occurred, yet after properly assembling the devices again, one came back alive, the other not. The one which has the screen and buttons not working right is the one that got thrown at me by a kind person. It most likely has physical damage somewhere, although I couldn't locate it. The other one didn't get damage and has screen and buttons work well after complete disassembly and assembly.
Both devices also have different screen types.
I now gave up both devices and am withdrawing myself from the HD2 world. Too many issues with the devices getting old.
sent from the tip of my finger
My usb port has been flaky for a while but finally gave out totally recently. It's actually loose inside the case. Over the past couple weeks my digitizer has also been going bad. I read about how you can press the power button hard to get it working again, which works but it seems only a matter of time for that thing too. Anyone got any recommendations for what I could do? I ordered an external battery charger and battery but all it accomplished was frying my old battery. :/ I might try to solder a new usb port on once I have good reason to (read: solid mango wp7 rom.) but if my digitizer is done it's not really worth it. Why would pressing on the power button revive it when it's not working? I'm hoping it's just a loose cable.
Bottom line, does anyone who's had these problems (they're the two most common HD2 hardware issues afaik) have any recommendations for solutions?
Your USB port issue probably can't be fixed.. unless you can find someone who is willing to help you solder a new usb port to your motherboard (or you can do it yourself if you have enough skills)
As for your Digitizer, you can open up your hd2, and check if the digitizer plug is loose (located under the lcd). If it isn't, that means your hd2 digitizer is dead, and you should order a replacement.. (of course, please see here
I have the same issue with my Infuse. The digitiser only seems to have a problem for the four bottom buttons. They have a mind of their own. The rest of the screen is fine. My USB port is intermittant. I'll probably just take it back to the store though. Sorry I cannot help.
So I bought a HD2 with bad touch screen. The issue was the very common one that every one knows, red button that was poking into the touch screen flex cable. I opened up the phone and fixed the issue and touch screen was working perfectly fine. In the process, unfortunately, I chipped a little edge of the front glass/digitizer. It was not a big deal as phone was still working fine. But I decided to buy a new front glass.
When my new front glass arrived, I separated the digitizer/front glass from LCD, but then half of my LCD got corrupted. So I ended up buying an LCD too!!!
Now comes the issue: when I put the phone together, touch screen doesn't work at all. I have tried all combinations of NEW / OLD digitizer and NEW / OLD lcd. Nothing works. I wonder if anyone can help me figure out why?
P.S. When testing, I happened to connect the phone to my 5w wall charger directly connecting it to power pins (without battery installed). Would that be why I lost touch? Is the touch issue now because of motherboard that was directly connected to adapter, not getting power from its designated battery?
have you tried the old lcd with old digitizer (which was working)?
tried it before replacing?
did you made some change to the software before replacing?
I currently have this problem too while trying to revive my old- almost 3 years inactive- HD2 with new touchscreen, and still trying to figure out where is the problem
b3rvirus said:
have you tried the old lcd with old digitizer (which was working)?
tried it before replacing?
did you made some change to the software before replacing?
I currently have this problem too while trying to revive my old- almost 3 years inactive- HD2 with new touchscreen, and still trying to figure out where is the problem
Click to expand...
Click to collapse
Yes I had tried the old LCD, and that didn't work either.
I installed a WiFi Keyboard on it.
Did you resolve this issue?