My usb port has been flaky for a while but finally gave out totally recently. It's actually loose inside the case. Over the past couple weeks my digitizer has also been going bad. I read about how you can press the power button hard to get it working again, which works but it seems only a matter of time for that thing too. Anyone got any recommendations for what I could do? I ordered an external battery charger and battery but all it accomplished was frying my old battery. :/ I might try to solder a new usb port on once I have good reason to (read: solid mango wp7 rom.) but if my digitizer is done it's not really worth it. Why would pressing on the power button revive it when it's not working? I'm hoping it's just a loose cable.
Bottom line, does anyone who's had these problems (they're the two most common HD2 hardware issues afaik) have any recommendations for solutions?
Your USB port issue probably can't be fixed.. unless you can find someone who is willing to help you solder a new usb port to your motherboard (or you can do it yourself if you have enough skills)
As for your Digitizer, you can open up your hd2, and check if the digitizer plug is loose (located under the lcd). If it isn't, that means your hd2 digitizer is dead, and you should order a replacement.. (of course, please see here
I have the same issue with my Infuse. The digitiser only seems to have a problem for the four bottom buttons. They have a mind of their own. The rest of the screen is fine. My USB port is intermittant. I'll probably just take it back to the store though. Sorry I cannot help.
Related
Hi, I come on here quite a lot for information as it's an amazing resource! This time however, I'm attempting to give something back!
I experienced the "black screen on slide out" on Monday. Phone completely screwed. I've also had a few droppages and had it apart once before so there's no way warranty is gonna help!
I stripped it down and soon discovered what it is that actually fails on the ribbon. The coating had worn through due to rubbing on something during the slide out / in process. it had been playing up for a while, probably due to shorting out on the metal case, but now the tracks (aluminium?) had worn right down.....
In pic 1 i've circled the worn area. The shiny section is where i'd tried taping over it to prevent shorting, before i realised the tracks were gone.
Got an almost new one off ebay for 15 quid and, realising it was going to happen again, came up with a solution that, so far, looks like it will work....
A while back I bought some "anti rattle felt" for my car's dashboard - really thin and strong self adhesive felt to prevent squeaking joins between dash sections. I cut a piece of this and stuck it to the new ribbon. Once this stuff is on it's well stuck, by the way!
See pic 2 for the modded ribbon cable.
On reassembly everything is working just fine so far! Here's hoping that it lasts longer than 6 months this time!
Just need a new casing now as mine is decidedly second hand!
Hope this turns out to be of use to someone!
cool story bro
when i took apart my xperia to replace the housing this seemed like a really weak point in the device. glad to see someone who has had the problem has been able to fix it
Why does the screen go black?
Hi,
When the coating wears off the ribbon cable it exposes the tracks in it. when you slide the keyboard out the exposed tracks short out on the metal casing and the screen loses it's input signal.
thats whats happened on mine at least and i presume quite a few others?
HTH!
Update:
That's interesting: My phone was also losing signal with the keyboard out, and occasionally while closed up as well. It would just randomly drop to "no signal" for a few seconds.
It hasn't done it since replacing the ribbon cable.....could be coincidental of course.
I'm having the same problem
It just started a week ago and I got the phone in January off of ebay. I'm new to opening up the phone so could anyone help me find the correct tools or have a link to a site with pictured instructions?
I noticed that the sliding mechanism started to go loose about 4-5 months ago but didn't expect the screen not respond in landscape mode. I have yet to see the other symptoms you all are referring to. I would like to fix this before it get worse.
In mine case it went totaly black after one week of this problem... You have all the instruction on youtube, there is where i looked. For tools you can be inovative, but the exactly right ones come with housings from ebay, it is only 15EUR, and i bet you have some cracks so it wouldn't hurt replacing. That is what i did, along with ordering new sliding mechanizm, and new ribbon cable.
I am open for ideas to prevent my ribbon cable from being cut at it weakest point again.
I'm assuming my flex ribbon went bad yesterday, since sliding the keypad out causes my screen to shut off.
Already ordered a cable off ebay and will attempt to replace it myself :O
Replaced my flex ribbon cable with one I bought on eBay. The screen doesn't turn on at all now, which leads me to believe the cable I was sent is defective. Put the old one back in and it works okay, less landscape mode. ughhh what a pain.
great tips! my input is I bought a case off of ebay that was ~60$ and everything actually fit fine for me...so I wouldn't discount every seller but you do get what you pay for, the 15$ cases are probablly the ones that will give you problems
I working in a mobilephone repair center if anyone need help drop me a priv... i able to get 2nd hand or even brand new components
Replaced the flex ribbon cable -
I got my flex ribbon cable a few weeks ago and took it to my local repair shop. They replaced it but the LCD screen/optical joystick receives no power. The touchscreen and everything else on the phone works just fine now. I thought it was a defective item so it was exchanged with a new one.
Got the repair shop to replace it again and the outcome still remains the same as the first.
Theres no light coming from the screen nor the side illumination.
I just told the repair shop to just place the original back in for the mean time.
Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power botton.
Could it be defective a batch that the seller was sending out? or the repair shop's mistake and is playing dumb so they do not have to admint fault?
Hopefully there's an easy fix to this problem.
-Also I did inspect the ribbon before and after the repair. looks new as the OEm
Can anybody help me out with this new problem after replacing the cable -
perhaps you should try a hard reset. Ive had problems in the past where the optical joystick and the illuminators did not work, and that worked for me.
On the other hand, the top illuminators are on the same piece of hardware as the flex cable that was replaced, so a faulty flex cable is possible. The bottom illuminators are on the circuit board that the optical joystick attaches to, separate but connected to the flex cable.
Ive recently replaced my flex cable and touchscreen. The experience i had with the faulty touch screen was that it appeared to receive no power, but was in fact displaying a dark backlit illumination that could only be seen in the dark. At the same time however, the screen did not display anything. I'm not sure if this is similar to your experience, but if so then your touchscreen would need to be replaced.
ive done all repairs on the xperia myself, and one thing ive discovered is if something doesnt work right after a repair, simply disassembling it and reassembling it to make sure all the connections are properly done has worked for me in the past.
"Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power button."
Now when you say the power button, do you mean that a red light appears under it?
I dont know if i can come to a conclusion or that i can help (or have helped) you come to a conclusion, but i can only assure you that the xperia acts out in strange and weird ways.
Good Luck!
Tags
Dismantle / Disassemble Sony Ericson Xperia X1
http://www.ifixit.com/Teardown/Sony-Ericsson-XPERIA-X1/788/1
http://www.formymobile.co.uk/xperiadisassembly.php
http://www.youtube.com/watch?v=AWDurQrRt-Y (REAR)
http://www.youtube.com/watch?v=iyGUbxFqvyc&feature=related (FRONT)
http://www.youtube.com/watch?v=elgC8hwHfYQ&feature=related
For info.
Mike
Thanks for the links. I've tried the hardreset and restoring the original rom but the issue is still there. It's really bugging me that everything works but the LCD screen. I'm currently using MyMobiler to use my phone. The touch screen works fine and so does the soft keys. Just no power for the lights. I might just give up and wait for another phone that catches my eye and then tinker with the xperia myself. but if anyone got a solution or want me to test something then I'll give it a try.
My warranty is no longer affective so I'll use my phone as a tester to help others with any problems.
TRIONDAVE, how's your Xperia running now with the cable mod that you did? Its been 6 months since you created the thread. I hope you're still around.
My Xperia X1 works nearly fine, except for the keyboard issues, so I'm thinking of opening it up. If your Ribbon mod helped I might just do it too once I've got it opened. Mine has a MOUNTain of cracks though, and the battery compartment itself is cracked on both side enough to make the compartment CURVED. Hence the Battery cover doesn't sit well.
I'm looking around for broken Xperias which I might be able to use to change the internal cracked casing. Lets see.
DatDereX1 said:
cool story bro
Click to expand...
Click to collapse
My thoughts exactly.
Hello guys, I am in need of real help over here!
Its just that Ive replaced my ribbon cable, the old one got screwd up.
However I got done for 10 minutes ago, tried to start up the phone.. without success :,(
The ribbon cable doesnt have anything to do with the start up, only the screen am I correct? Cause I cannot even start my phone..
Ive connected the charger, but when I remove the battery it shows a red light, meaning no battery, correct?
So what may the problem be exactly? Maybe the battery is all dead, or?
PLEASE HELP!
for the people with ribbon failures how long have you had the phone before it occurred ? im just interested on the cables lifespan.
mine is fine so far but i have noticed the slider is flimsy and rocks left and right.
For weeks, hell months now I have been reading through threads about HD2's not responding to touch. I had just about every sympton everyone else had.
-touch would work then not
-soft reset would fix problem
-reload to OEM specs, temp fix
Finally like most, my phone stopped responding to touch too. Must be the digitizer. So I aquired another HD2 and went about my life. Some months later I aquired a third HD2 with a bad charging port. Everything else worked fine. So I took the main board out of the one I orginally had with the bad digitizer and swapped it with the one having the bad charging port. Guess what...the touch doesn't work after the swap. So I swapped back and it worked!!!!!
I then took the original LCD and Digitizer which I though was bad, hooked it up to the mainboard with the bad charge port and volia!!! Digitizer works. I left it like that a few days and it worked fine. I have and induction charging system for the phone so I used that to charge while I performed my tests.
I did lots more swapping and testing and my final result is the main board from my original phone is the culprit of the digitizer not working. Digitizer from both phones always works when hooked to the mainboard with the bad charge port and never works with the orginal mainboard.
After all the threads I read through I haven't seen anyone else with the mainboard being the problem/solution to the digitizer not responding so I though I would share. Keep in mind, even though the digitizer didn't respond with the bad mainboard, all other functions worked. The hard buttons responded, I could answer phone calls with them. I could communicate with the phone via USB, etc.
Joe
I have a Samsung Vibrant T959 TMobile US with 2.1-update1, Baseband T959UVJI6.
The battery is fully charged, it registers in the phone as fully charged 100%, but when I hit the power button I get a progess wheel that gets stuck, then the phone just turns off. It never gets passed that wheel, it only displays for a second then dies.
However, when I plug in the USB and hit the power button, it comes right up like it should. Then I can unplug the usb and use the phone just fine. Its almost as if I need to jump-start the phone with a power source.
I have reset the phone, even re-flashed the stock firmware using Odin. Same results. I have even swapped batteries with a buddy just to see if that was the case, but I still got the same results.
Any advice or suggestions is GREATLY appreciated. Thanks Very Much In Advance!
Anybody? Any ideas?
Well, that is new to me...
I'll preface with, I have no clue how/why that is happening. But, this is what I would do:
1 - If really opposed to rooting, I'd call T-Mo / Samsung and get a replacement.
2 - If I liked my phone and wanted to make it better, I'd root it and flash a custom ROM. It likely would take care of the issue, as it clearly is not a hardware thing (well, I say clearly).
Worst case with #2, ODIN back to stock and then do option 1.
possible solution
also it says "USB connected" even when cable is unplugged? I had similar problem.. I tried everything, flashing, changing batteries.. none of that was useful. Then I find some post on some forum that says it might be corrosion, so i scratched my USB with thin wire and everything worked fine, but also scratching USB I was doing one more thing. In my opinion, I think that it's not corrosion. I think that USB is slightly bent (middle part of it), try to bent it in other direction, possible that it's too close to edge. That solved my problem. Tell me if this helpful for you, sorry about my english
we87 said:
Anybody? Any ideas?
Click to expand...
Click to collapse
did you ever figure out? im in the same boat...
admirh said:
also it says "USB connected" even when cable is unplugged? I had similar problem.. I tried everything, flashing, changing batteries.. none of that was useful. Then I find some post on some forum that says it might be corrosion, so i scratched my USB with thin wire and everything worked fine, but also scratching USB I was doing one more thing. In my opinion, I think that it's not corrosion. I think that USB is slightly bent (middle part of it), try to bent it in other direction, possible that it's too close to edge. That solved my problem. Tell me if this helpful for you, sorry about my english
Click to expand...
Click to collapse
i think i can get what you are saying, cleaning the usb port on the phone right??
BUT how does this affect turning the phone on?? if usb port is rusty, it will only affect charging, not turning the power on?
I experienced this identical issue last fall -- the USB would always say it was connected, wouldn't startup unless connected to actual USB, but otherwise worked fine.
Take your phone apart and look at the solder joints on your microUSB port... mine all had cracks in them or had broken free. I re-flowed the solder while holding the port down and it resolved my issues. (put on some flux, and run a hot soldering iron across the joints, clean up... it's not very difficult. just be sure you don't short out any of the pins.) I also added additional solder to the four points that just hold the mircoUSB to the circuit board. It's been rock solid since
Rahhstah said:
I experienced this identical issue last fall -- the USB would always say it was connected, wouldn't startup unless connected to actual USB, but otherwise worked fine.
Take your phone apart and look at the solder joints on your microUSB port... mine all had cracks in them or had broken free. I re-flowed the solder while holding the port down and it resolved my issues. (put on some flux, and run a hot soldering iron across the joints, clean up... it's not very difficult. just be sure you don't short out any of the pins.) I also added additional solder to the four points that just hold the mircoUSB to the circuit board. It's been rock solid since
Click to expand...
Click to collapse
that sounds very difficult actually.. as I dont own any of the tools
anywhere cheap to recommend?
lazi punk said:
that sounds very difficult actually.. as I dont own any of the tools
anywhere cheap to recommend?
Click to expand...
Click to collapse
See if there is a TV or electronic repair place still in business in your area. Or post an ad on CL asking someone with knowledge and skill to do it. Be careful they aren't an idiot just wanting 20 bucks and happen to own a soldering iron.
lazi punk said:
that sounds very difficult actually.. as I dont own any of the tools
anywhere cheap to recommend?
Click to expand...
Click to collapse
you could see if Cell Phone Repair/ is near you and describe to them what you want to do.
I would go through these guys they are top notch helped me when i soft bricked my wife's phone. He even convinced me that i could fix it myself when i was ready to send it to them for a jtag.
They can replace the usb plug if thats the issue.
http://mobiletechvideos.mybigcommerce.com/samsung-vibrant/
I would test to see if my battery is bad first before i went about resoldering, it could easily be a bad battery.
Xdogg said:
I would go through these guys they are top notch helped me when i soft bricked my wife's phone. He even convinced me that i could fix it myself when i was ready to send it to them for a jtag.
They can replace the usb plug if thats the issue.
http://mobiletechvideos.mybigcommerce.com/samsung-vibrant/
Click to expand...
Click to collapse
thank you for the response. I definitely think the usb port is an issue. what is a jtag? haha
ferhanmm said:
I would test to see if my battery is bad first before i went about resoldering, it could easily be a bad battery.
Click to expand...
Click to collapse
No my stock battery is charging and i did buy a separate battery. same issue.
Hey,
i got the typical problem that my screen wasnt responding after use of endbutton. Sometimes it was working.
I now disassembled the device and saw that the flatcable had a small scratch and i guess the first one or two cables are brocken already and only get contact sometimes by luck.
So does anybody know if there is a way to repair this ?
A new touchscreen isnt to expensive 20-30€ but why throw away a working one if a cable is repairable easily?
Next time i will glue the cable to the display so that there is no flexing when pressing the endbutton. The problem is that there is a little space between that is pushed away each use of the endbutton and someday the problem occours.
Hi,
I had to replace my touch screen to solve the same issue
Is there any thing we can do to prevent the same damage to the new screen ?
Thanks
Well i tried a few times to fix the issue.
But its hard to solder the flex cable without totally burning it.
If i solder it its very likely to break fast again.
Im going to buy a new digitizer too..
To your question:
Yeah i saw that there space between the flex cable and display. The cable is bent a bit towards the buttons. When you push the button the cable is bent back in the free space.
I will glue the flex cable directly to the display and put a layer of protective tape over it. so it wont bent (What causes our error) and wont scratch(if this could happen too).
The problem is the poor quality of the flex cable. Its very hard and therefore breaks easily what causes the wires to break to sooner or later.
If i can ill try to take a few photos but its hard as my digicam cant focus so closely..
Hi,
i bought a factory refurbished I9600F from aliexpress. It worked great for 3 days, then the phone became slow to respond, the screen was flickering in yellow-green tones, and then wouldn't come back on but stay black. (but I would still get notification sounds for incoming messages, the notification LED was still working, and the menu keys also light up when I press home/power).
Pulling the battery fixed the issue once, but the problem came back after 1 hour.
I managed to revive the phone once more by pulling the battery and holding the power button to drain all remaining power in the device. The phone was working again for a few hours, but now it's back to having a black screen and even the power drain method doesn't work anymore...
So i'm guessing that replacing the screen won't fix the issue, since the screen is working just fine for a a while (both image and touch are perfect) - but then somehow there must be some electrical issue that causes the graphics unit to malfunction.
I checked the easily accessible connector to the left side of the battery, but it seems that the screen is mainly connected via flex cables that cannot be accessed unless you heat up your device and pry out the screen.
I have found some information on the internet that pressing hard on the spot where the flex cable connector is might fix the problem, but this didn't work for me.
FYI, I'm running the default Samsung firmware the device shipped with and used Kies + OTA update to get the latest official FW. No rooting or any other mods. Just some regular apps installed.
Any recommendation what I could try to fix this problem? Thank you all!!!
BTW, I have found similar reports on the internet here:
http://forums.androidcentral.com/samsung-galaxy-s5/405238-galaxy-s5-static-screen-won-t-turn.html
But the linked how-to-fix guide states that heating up the display assembly is only recommended on devices with a broken screen... So now I don't want to risk breaking my working screen.
So mainly my options are
a) open the device to check the flex cable connection
b) buy a new battery to see if that solves if (some people have reported success with a different battery)
c) buy a new screen assembly on aliexpress for around €135 and hope that a new screen will fix it...
Thoughts?
wutzin said:
So mainly my options are
a) open the device to check the flex cable connection
b) buy a new battery to see if that solves if (some people have reported success with a different battery)
c) buy a new screen assembly on aliexpress for around €135 and hope that a new screen will fix it...
Thoughts?
Click to expand...
Click to collapse
Hello, how did you solve this? I currently have the same problem.
gustav9797 said:
Hello, how did you solve this? I currently have the same problem.
Click to expand...
Click to collapse
sorry, i actually never was able to get this resolved. I tried removing the screen to get to the flex cable, but broke the screen because I hadn't heated up the glue enough...
Had to buy another device.
Sorry I don't have better news...
wutzin said:
sorry, i actually never was able to get this resolved. I tried removing the screen to get to the flex cable, but broke the screen because I hadn't heated up the glue enough...
Had to buy another device.
Sorry I don't have better news...
Click to expand...
Click to collapse
I'm going find out the cause for this issue. I've disassembled one device that only lights up when it is warm. If I put it in the cooler it refuses to light up for some time after that. I tried placing only the screen in the cooler, also only the phone body in the cooler, but couldn't find any difference doing this as it refuses to light up both times for a couple of minutes then it works great again.
I've ordered another device that had its screen shattered so I will try my current screen on that device.
It could be some internal hardware fault in the mobo, it could be the LCD connector having a bad connection somehow, it could be the screen assembly itself, but I will find out eventually.
I've seen many places on the internet where people say this is a software issue. There is a very simple answer to that question. How could it be a software issue if not even the boot logo shows up when you start the phone?
I will keep this thread updated.
Verified that this is a problem with the motherboard. What circuit on the motherboard could have problems with cold temperatures? The main power one? If so, I will try replacing it with a different one.
Update: Was not able to fix it. Motherboard is now scrap.