i've read through some of the threads but i can't find anything that would help...i was installing a viperrom and now my phone wont go passed the samsung boot screen i can't access the recovery my computer wont even detect my phone how can i fix this
reboot into cwm3 and wipe data,cache ,dalvik x3 then flash rom
my guess iss that you didn't odin before you installed the rom ?
This might sound like a dumb question, but...did you turn off the phone before trying to get to recovery? As in, did you pull the battery so you could actually get the phone off?
If you can't get to recovery, did you try going in download mode and then plugging it in?
The point here is that since you can at least get the samsung logo you're not bricked...because you're still getting a response
Sent from my baked and emotionless SPH-D700
i tried to put my phone in download mode and plugged it in but the computer can't detect my phone when i open odin
just redownload the drivers
Download the 32-bit even if you're on a 64-bit computer
the 32-bit drivers seem to work better install them then restart your computer and phone then retry ODIN
You can get the Drivers in this thread....
http://forum.xda-developers.com/showthread.php?t=770388
You's go a soft brick =3
From My Samsung Epic Using TapaTalk.
ive redownloaded the software and still can't detect my phone
all im able to do right now is get my phone into download mode but odin still can't detect it...or do i only need the .tar file in the pda slot and my phone will receive once its connected ?
do you have another computer you can try?
did you try using diffrent ports to plug your phone in?
lol one of my epics still does it. Does it do this?
http://s42.photobucket.com/albums/e...on=view¤t=video-2011-02-05-07-52-00.mp4
yup trying to sell it as is since i can't fix it. Hello epic #2/ second line, and yes it stays there. No computer detect it, yes it gets into recovery no it wont load up roms lol.
odin finally detects the port but i used the tar.md5 file from the link and says hash value is invalid?
robertobmwm3 said:
odin finally detects the port but i used the tar.md5 file from the link and says hash value is invalid?
Click to expand...
Click to collapse
Is it the dk28 tar or the di18 tar?
and yes i did try all ports and like i said it says theSPH-D700-DK28-8Gb-REL.tar.md5 is invalid
correct it is the dk28
robertobmwm3 said:
and yes i did try all ports and like i said it says theSPH-D700-DK28-8Gb-REL.tar.md5 is invalid
Click to expand...
Click to collapse
You need to rename the file to-
SPH-D700-DK28-8G-REL.tar.md5
Just delete the b and everything will be fine.
hell yeah thanks alot now it says set up connection what should i do now?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-D700-DK28-8G-REL.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
robertobmwm3 said:
hell yeah thanks alot now it says set up connection what should i do now?
Click to expand...
Click to collapse
What says "set up connection"?
Edit: Oh, I see.
Select PDA place the .tar file in PDA Section
uncheck F.Reset time
select victory_8G_100528.pit in the pit section
connect your phone
then hit start
iSaint said:
Select PDA place the .tar file in PDA Section
uncheck F.Reset time
select victory_8G_100528.pit in the pit section
connect your phone
then hit start
Click to expand...
Click to collapse
Did you put you phone into download mode before you connected it?
Related
iam useing odin and i have all the files downloaded and when i hit start it says
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-D700-DI18-8Gb-REL.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
and it wont load pass that will someone plz help me
Tyler145 said:
iam useing odin and i have all the files downloaded and when i hit start it says
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-D700-DI18-8Gb-REL.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
and it wont load pass that will someone plz help me
Click to expand...
Click to collapse
Are you sure your phone is in download mode? (press one and power..)
and dont you need usb debugging on for odin?
Power off your phone, disconnect the cable from both ends, close Odin, boot back into Download Mode, reopen Odin, connect the cable, try again.
Please post questions in Q&A. This is not the Q&A section.
soryy for posting here and yes it in download mode and i have did that already i unplug it alot and plug it back in
Use a non-stock USB cable.
iam useing a blackberry cord
Tyler145 said:
soryy for posting here and yes it in download mode and i have did that already i unplug it alot and plug it back in
Click to expand...
Click to collapse
Redownload odin and usb drivers and tar file....are u sure its in the PDA section?
i redownload everything 3 times and yes it i have it in the pda i done this b4 and it worked fine for me but idk whats wrong i been trying for hours
Tyler145 said:
i redownload everything 3 times and yes it i have it in the pda i done this b4 and it worked fine for me but idk whats wrong i been trying for hours
Click to expand...
Click to collapse
Use these:
Odin/PIT
EC05 TAR
Switch to a different USB port, and if that doesn't work, a different PC.
Have you tried restarting your Computer/ changing USB ports (use the back ones if it's a desktop).
i have those downloaded and i have change everyport and i dont have a diff pc only 1
Tyler145 said:
i have those downloaded and i have change everyport and i dont have a diff pc only 1
Click to expand...
Click to collapse
Got any friends?
i tryed on a friend pc and it did not work idk whats wrong should i just call sprint to get a new cell ?
Tyler145 said:
i tryed on a friend pc and it did not work idk whats wrong should i just call sprint to get a new cell ?
Click to expand...
Click to collapse
No. Try a different USB cable, different from the one you're using (don't care what it is). Try Heimdall. Remove the battery from the phone and leave it that way for two hours, then come back and try again. Switch up the order you're connecting between device and PC. Make sure the TAR is in the right place.
ok thanks i will post back in 2 hours i will unplug the batt for a while
Also try to reboot the pc afther installing odin and see if that works
Sent from my SPH-D700 using XDA Premium App
And if all else still fails, try running Odin with the battery removed from the phone...
Pull Battery from Phone,
Connect USB Cable to Phone,
Start Odin,
Boot Phone into Download Mode by holding 1 and Power (with battery still removed),
Flash .tar file.
I normally don't have issues when using Odin, but the few times I have had Odin fail on me (in multiple attempts consecutively), I have then been successful by pulling the battery out and flashing again.
What version of Odin are you using? I have been using 1.6 which has always seemed to work. Here is a good place with lots of Odin advice and files:
http://forum.xda-developers.com/showthread.php?t=773032
HEEEELP.. Was trying to flash to stock JVP through ODIN and i mistakenly remove my fone during flashing.
Now my fone does not even bootup anymore. It can only get to download mode.
I've tried to flash again but got no result. see ODIN message during flash below.
<OSM> Please wait..
<OSM> CODE_I9000XXJVP_CL264642_REV03_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9000XXJVP_REV_00_CL1019177.tar.md5 is valid.
<OSM> GT-I9000-CSC-MULTI-OXAJVP.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9000XXJVP_CL264642_REV03_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9000XXJVP_REV_00_CL1019177.tar.md5 is valid.
<OSM> GT-I9000-CSC-MULTI-OXAJVP.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
won't go pass the setuConnection.
PLSS HELP.
This is not a brick. Have you tried to Re-open ODIN or to Restart the Computer?
i've tried both. it does not get pass the <ID:0/005> SetupConnection..
Restart computer.
Unplug phone.
Start odin.
Add files.
Connect phone.
Flash.
Be patient.
Sent from my GT-I9000 using XDA Premium App
i've restarted the computer, unplug fone, start odin but it still stops at "<ID:0/005> SetupConnection.."
Also, take battery out of phone and wait for 20 seconds. then do as above.
gizmolala said:
i've restarted the computer, unplug fone, start odin but it still stops at "<ID:0/005> SetupConnection.."
Click to expand...
Click to collapse
Sometimes just waiting a while does it. Get a different version of odin maybe?
gizmolala said:
i've restarted the computer, unplug fone, start odin but it still stops at "<ID:0/005> SetupConnection.."
Click to expand...
Click to collapse
You loading up files into odin before or after you plug the phone in?
I know you are probably freaking out right now but if you can get download mode then it's still recoverable.
jcspecs said:
You loading up files into odin before or after you plug the phone in?
I know you are probably freaking out right now but if you can get download mode then it's still recoverable.
Click to expand...
Click to collapse
Exactly m8
Try using Odin 3.1 & flash with that if problem persists.
i loaded up files into odin b4 connecting my fone.
am using odin3 v1.85. where can i get 3.1 from pls
gizmolala said:
i loaded up files into odin b4 connecting my fone.
Click to expand...
Click to collapse
When you plug the phone in, is windows registering it and if so, are the drivers working correctly?
gizmolala said:
am using odin3 v1.85. where can i get 3.1 from pls
Click to expand...
Click to collapse
1.85 should be good. Try 1.7 maybe.
Could always try using heimdall instead of odin
Sent from my mosaic powered SGH-I897 using XDA Premium App
pls can u point me to where i can download heimdall from?
rquiett said:
Could always try using heimdall instead of odin
Click to expand...
Click to collapse
A valid point. Try Heimdall.
Have you removed sd- card and sim. Happened to me once. Removing both did the trick.
Sent from my GT-I9000 using XDA App
It's not a brick yet, dont worry.
1. Can you still go to the recovery mod? try to wip data/factory reset. reflash it.
2. If possible, do you have froyo 2.2 official (just as it's only one file in TAR)? Just flash it. Then flash 2.3.4 again.
Thanks all for your help.. I've tried all your suggestions but my phone won't actually boot to download mode anymore.
I've tried several times to go to download mode but to no avail. Screen is always blank (Black Screen) every time i tried.
gizmolala said:
Thanks all for your help.. I've tried all your suggestions but my phone won't actually boot to download mode anymore.
I've tried several times to go to download mode but to no avail. Screen is always blank (Black Screen) every time i tried.
Click to expand...
Click to collapse
take battery out for 10 mins then put it back in and try to go straight to download mode, see if that works
I tried rooting it, It ****ed up Then i tried restoring gingerbread via odin it sat there for 2-3 hours stuck on file so i unplugged it ( dumb idea ) now when ever i turn on my phone i get sent to android system recovery <3e> and when i click wipe data / factory reset nothing happens. and when i press the volume down button it doesn't take me to the download screen it just takes me here. Why must i be so retarded.
It says e: failed to mount /data/fota (no such file or directory ) when i first get to this screen.
Sometimes you might be able to get into Download Mode if you do the following.
1) Remove Media Card, SIM and Battery
2) Have Odin up and running
3) Plug in the USB cable
4) While holding volume down plug in the battery
This might get you into Download Mode. I did this myself and ended up sending it back to Samsung in the end.
I then bought a JIG from MobileTechVideos and thats by "oops" backup now. If those steps dont work to get into Download Mode I'd say go get a JIG
Even when the phone wasn't ****ed up I could never get into download mode unless the battery was in.
Do you know for certain the driver is installed and works/worked at one time? Did you ever transfer files from pc to phone in usb mode?
sfd0124 said:
Do you know for certain the driver is installed and works/worked at one time? Did you ever transfer files from pc to phone in usb mode?
Click to expand...
Click to collapse
Yes, I also tried 12 different usb ports and Now I am getting an un authorized battery error and It wont charge and it's almost dead :/
Do you have a verizon fascinate?
Are you able to get into download mode?
Have you tried heimdall?
Im waiting for FedEx to get here with my GNex... If you want to chat via google talk we can try to get it running again. Send me a pm if interested.
That or if you're willing to wait a couple days, order a USB jig off of eBay. The wait will suck, but it beats buying a new phone
Sent from my Galaxy Nexus using xda premium
vilhjalmr said:
I tried rooting it, It ****ed up Then i tried restoring gingerbread via odin it sat there for 2-3 hours stuck on file so i unplugged it ( dumb idea ) now when ever i turn on my phone i get sent to android system recovery <3e> and when i click wipe data / factory reset nothing happens. and when i press the volume down button it doesn't take me to the download screen it just takes me here. Why must i be so retarded.
Click to expand...
Click to collapse
I've unplugged my phone many times during ODIN when it just hangs....not a deal breaker or phone bricker in anyway. The key is to get to download mode.
Go here: http://forum.xda-developers.com/showthread.php?t=1349895 and get the full gb version and the atlas pit file.
Make sure your drivers are current. Take battery out. Plug USB into phone first, then computer, then hold down volume rocker to get into Download mode.
Open Odin, put the pit file in Pit section, the GB file in the PDA section and hit Start.
Also try a differant usb cable
It my be a bad cable
jmac9 said:
I've unplugged my phone many times during ODIN when it just hangs....not a deal breaker or phone bricker in anyway. The key is to get to download mode.
Go here: http://forum.xda-developers.com/showthread.php?t=1349895 and get the full gb version and the atlas pit file.
Make sure your drivers are current. Take battery out. Plug USB into phone first, then computer, then hold down volume rocker to get into Download mode.
Open Odin, put the pit file in Pit section, the GB file in the PDA section and hit Start.
Click to expand...
Click to collapse
Thanks for the replies I really appreciate it, I cannot get into download mode as when i press the volume down it just goes to android system recovery and no where else so I bought a jigg, hopefully It comes soon
Alright so I got my jig and my new charger + battery's but it's still sitting on the same part where it got bricked before on odin it just says
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CI500_VZW_EH03_GB_CM.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> param.lfs
<ID:0/003> Sbl.bin
<ID:0/003> boot.bin
<ID:0/003> recovery.bin
<ID:0/003> zImage
<ID:0/003> factoryfs.rfs
<ID:0/003> dbdata.rfs
<ID:0/003> cache.rfs
<ID:0/003> movinand.bin
<ID:0/003> modem.bin
and it's been at that mode.bin for about 40 minutes now... and when this happened last time the battery fell out of the back and that's how it got bricked... should it be taking this long?
Not sure
Bionic
Which Odin files are you using? Some GB Odin tars don't have everything you need to restore from some bricks. Get a Verizon version. Plus it sounds like your using phone instead of PDA. I've done out beefier and had similar symptoms.
Sent from my SCH-I500 using Tapatalk
Stephen.k.spear said:
Which Odin files are you using? Some GB Odin tars don't have everything you need to restore from some bricks. Get a Verizon version. Plus it sounds like your using phone instead of PDA. I've done out beefier and had similar symptoms.
Sent from my SCH-I500 using Tapatalk
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1238070&page=1
I'm using the GB files from there and i am doing PDA. i've left it for like 4 hours now So i'm just going to try installing VIA sd card.
Try the ed05 ROM found here.
http://forum.xda-developers.com/showthread.php?t=1124391
Also use the pit found there. This always gets me it when things go bad.
If that doesn't work you might be screwed.
Sent from my SCH-I500 using Tapatalk
Stephen.k.spear said:
Try the ed05 ROM found here.
http://forum.xda-developers.com/showthread.php?t=1124391
Also use the pit found there. This always gets me it when things go bad.
If that doesn't work you might be screwed.
Sent from my SCH-I500 using Tapatalk
Click to expand...
Click to collapse
I am installing this now and for the past 15 mins it's been stuck at movinand.bin i'll let it sit there for an hour before I install via sd card, Keep in mind I'm not using the verizon fascinate I'm using the telus fascinate 3g+ which is the SGH-T959D
well now my phone boots up if i try to go to download mode it goes to the system recovery mode how ever if i let it try to start normally it boots up and just sits on a verizon wireless logo for ever
OMG it took about 10 minutes but it loaded!!!!!
vilhjalmr said:
OMG it took about 10 minutes but it loaded!!!!!
Click to expand...
Click to collapse
So you're good?
Sent from my SCH-I500 using Tapatalk
i downloaded the coDrom v1 and installed it without using cwm....so nw wen i start my phone ,... it's stuck on the screen which displays samasung galaxy y gt s-5380......and also wen i try to enter in recovery mode...the same things happens.....and can't access anything....plz tell me wat to do.....can't even see anything except the startup screen
.:crying::crying::crying:
You bricked ur phone try flashing odins.... Search for it on xda or google......
Thank mee if i helped uuu......
Sent from my awesome y......
harrynxo92 said:
i downloaded the coDrom v1 and installed it without using cwm....so nw wen i start my phone ,... it's stuck on the screen which displays samasung galaxy y gt s-5380......and also wen i try to enter in recovery mode...the same things happens.....and can't access anything....plz tell me wat to do.....can't even see anything except the startup screen
.:crying::crying::crying:
Click to expand...
Click to collapse
There's no need to worry. You just Soft Bricked your phone. ) (I've faced this problem a lot of times buddy)
Go to this post and download the required build according to your country. Follow the steps and Voila, STOCK ROM !
http://forum.xda-developers.com/showthread.php?t=1465800
Please press the thanks button if you think I helped you, It's to the left of this post.
Yeah goto SamFirmware.Com and download latest version...
Goto Download Mode by Pressing Vol down + home + power and Connect it to pc use compatible odin and flash...
Happy Flashing
Peace
Hit Thanks & It will Disappear
Sent from S II Running Official ICS 4.0.4 with Siyah 4.1 [/size]
Omaxe said:
Yeah goto SamFirmware.Com and download latest version...
Goto Download Mode by Pressing Vol down + home + power and Connect it to pc use compatible odin and flash...
Happy Flashing
Peace
Hit Thanks & It will Disappear
Sent from S II Running Official ICS 4.0.4 with Siyah 4.1 [/size]
Click to expand...
Click to collapse
Nope, SamFirmware.Com always dont have odin flashable packages, use the stock firmwares from doky73s stock firmwares thread of android development
got stuck again
i got stuck again on odin on
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_S5360_DDLF2.tar.md5 is valid.
<OSM> MODEM_S5360_DDLF1.tar.md5 is valid.
<OSM> CSC_S5360_ODDLF1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
m aolo nt able to go in my recovery mode also... please help me ASAP
silent_screamer said:
i got stuck again on odin on
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_S5360_DDLF2.tar.md5 is valid.
<OSM> MODEM_S5360_DDLF1.tar.md5 is valid.
<OSM> CSC_S5360_ODDLF1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
m aolo nt able to go in my recovery mode also... please help me ASAP
Click to expand...
Click to collapse
i experienced that also but i made it...
Try to off your phone first, then take out the battery and sd card.. put it again after few seconds, then re-do the procedure given to you.
Try to close also samsung keis program and be patient sometimes Setup Connection take a few seconds or a minute...
I cannot open ma recovery mode...!!!!:crying::crying::crying::crying:.
My System does not recogonize my phone...!!!:crying::crying::crying:
I have the Odin3 1.85.. and the rom package too...!! i also did install the USB driver..!! but stil.. i can;t do anythin..!!
all this started wen I tried to over clock my phone..!
Now,, all I have is the start up screen,,, nothing else...:crying::crying:
Please Help Me,,!! i am a New guy.. in dis,,,, Rooting n... al those stuff...:crying::crying:
NewBeeie said:
I cannot open ma recovery mode...!!!!:crying::crying::crying::crying:.
My System does not recogonize my phone...!!!:crying::crying::crying:
I have the Odin3 1.85.. and the rom package too...!! i also did install the USB driver..!! but stil.. i can;t do anythin..!!
all this started wen I tried to over clock my phone..!
Now,, all I have is the start up screen,,, nothing else...:crying::crying:
Please Help Me,,!! i am a New guy.. in dis,,,, Rooting n... al those stuff...:crying::crying:
Click to expand...
Click to collapse
Ensure you must install latest Samsung drivers..
Try to connect your phone in download mode.. (Volumedown+home+power)..
It will detect..(Shows in Picture).
If not pull out our battery and go to download mode again and connect..(Try until it detects)
Flash Stock rom.. & Reply..
Calm down don't panic or else you'll fail. Here are the steps.
1. Install the correct drivers for your phone (drivers can be installed through kies)
2. Download odin with the appropriate firmware of your country
3. Connect your phone to the computer in recovery mode (volume down+ menu+ powerbutton)
4. After connecting on, there top of odin there will be a yellow box that would say com 0:[COM:X] (x is any number)
5. After connecting fill pda, phone,csc.
6. Flash it with no interruptions.
7a. If u are successful then you can turn on your phone
7b. If your not successful then repeat step one and make sure you do it properly.
8. Press the thanks button
Sent from my Titan TV S320 using xda premium
is der any problem if I use the Kies instead...???????????
amtra said:
Ensure you must install latest Samsung drivers..
Try to connect your phone in download mode.. (Volumedown+home+power)..
It will detect..(Shows in Picture).
If not pull out our battery and go to download mode again and connect..(Try until it detects)
Flash Stock rom.. & Reply..
Click to expand...
Click to collapse
No... No luck dude.....:crying:
I just went on Doing it... stil no sign..!!
My pc doesn't show anything when I connect my phone.....
amtra said:
Ensure you must install latest Samsung drivers..
Try to connect your phone in download mode.. (Volumedown+home+power)..
It will detect..(Shows in Picture).
If not pull out our battery and go to download mode again and connect..(Try until it detects)
Flash Stock rom.. & Reply..
Click to expand...
Click to collapse
Hey..!!!!:laugh:
Thankz alot buddy...!!! I got my phone fixed up..!!!
I actually thought that the Recovery Mode is same as the Download Mode..!!!
N.. i kept on pressing the Volume up key... instead of Volume Down key...!!!
Datz y..!!!
Anyways.. all the other files ... lyk odin.. n otherz.. did play their part...:fingers-crossed: Thankz Aloooooooooooooooooooooooooooooooooooooooooot for that....!!!!!!!!!!!!!!!!
so.... if I hav any more problems... I wil post 'em up.. do Help me ok...:cyclops::
Thankz..!!!!!!!!!!!!!:victory::victory::victory::victory::victory::victory::victory::victory::victory::victory:
i have gt6103 not s5360 but i have the same problem. I cant go to download mode and i was thinking maybe you could help me. The thing is that i have WHITE SCREEN and i cant do anything so i suppose i have hard brick. Is there any solution? thanks in advance
zaf_4 said:
i have gt6103 not s5360 but i have the same problem. I cant go to download mode and i was thinking maybe you could help me. The thing is that i have WHITE SCREEN and i cant do anything so i suppose i have hard brick. Is there any solution? thanks in advance
Click to expand...
Click to collapse
Try a usb jig.
Sent from my GT-S5360 using xda app-developers app
zaf_4 said:
i have gt6103 not s5360 but i have the same problem. I cant go to download mode and i was thinking maybe you could help me. The thing is that i have WHITE SCREEN and i cant do anything so i suppose i have hard brick. Is there any solution? thanks in advance
Click to expand...
Click to collapse
Flash stock rom via odin as if the screen was working
in other words
Connect phone to pc & open odin
enter download mode on phone
If get white screen do what you would do if it was fine
so push volume up
then flash stock rom
you may get lucky & it flashes
marcussmith2626 said:
Flash stock rom via odin as if the screen was working
in other words
Connect phone to pc & open odin
enter download mode on phone
If get white screen do what you would do if it was fine
so push volume up
then flash stock rom
you may get lucky & it flashes
Click to expand...
Click to collapse
I used usb jig but nothing...just still white screen.. and ofcourse did what you said trying to flash with white screen through odin but no luck...
sohar85 said:
how to resolve the problem….i have galaxy y young….i got this problem after reset….
AFTER try a lot i enter the recovery mode……its just says formatting….and reboots automatically ….again and again
Click to expand...
Click to collapse
Support isn't given for banned roms here
Enter download mode & flash stock rom via odin
thanks
Thank i am also searching for odin
Galaxy Y: can,t go to recovery mode ( Odin Mode)
my samsung galaxy young can't go to recovery mode and the odin mode always appear. i did heard that flashing will do it, but it still won,t working...
I love my Continuum but for the last two weeks it has been behaving badly...unsolicited reboots, taking forever to activate the phone, etc. My thinking is I've got nothing to lose by upgrading from Froyo (2.2.2) to GB in the hopes of regaining some performance. I'm a noob and based on what I've read here and other places I needed to downloaded the drivers, Odin3 v1.85, garnett_3.pit and SCH-I400-EG04-Ginger-Rel.tar.md5. Then follow these steps:
1. Download and Install USB Drivers
2. Download and Install Odin
3. Put phone in Download mode by holding Vol- and Power buttons simultaneously to get to Samsung Recovery Utilities
4. Start Odin
5. Connect phone to computer with USB cable
6. Wait until a Device is detected on COM port ( get a yellow box indication)
7. Map to .PIT file on PC
8. Map to .MD5 file on PC
9. Verify re-partition, auto reboot and F. Reset Time boxes are selected
10. Go...
Step 6 was never reached (device detection) when I put the phone in Download mode per Step 3. I left the PC-phone connected for nearly an hour and nothing. So I took a chance and turned on USB debugging and just plugged it in. Success! Odin indicated a device detected. Proceeded with the rest of the steps above to a point where the following messages appear in the Message Box:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I400-EG04-GINGER-REL.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
And I wait. And wait. And wait some more. After 15 minutes, still nothing. PC is quiet, too. When I've convinced myself that I've given it enough time, I dismount the PC/phone connection and the following messages appear:
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
What am I'm doing wrong or need to try to complete the upgrade? Any help will be greatly appreciated.
Thanks,
cncboy
I'd try Heimdall, see if that'll help If you need help with that, let me know. Basically you need to extract The *.tar file using 7-zip, then load up each file one at a time in said program...
EDIT: it's been a while, but I remember this happening when I was using a wrong PIT file. I don't know if that's what's going on, but just an idea.
Curious...
Thanks, Trailblazer. I found a video on youtube that supposedly does what I'm trying to do. I'd post the link but I haven't had 10 posts yet. If you're interested, it can be found on youtube. The title of the video is "How to Update Samsung SCH I400 to Android 2.3.3 Gingerbread"
I downloaded the same pit and tar files that the guy in the video did. Are the drivers supposed to be anyplace special on my computer? I choose the default when executing the install and it created a folder at C:\Program Files\SAMSUNG. I'm running this on Win XP.
Thanks!
cncboy said:
Thanks, Trailblazer. I found a video on youtube that supposedly does what I'm trying to do. I'd post the link but I haven't had 10 posts yet. If you're interested, it can be found on youtube. The title of the video is "How to Update Samsung SCH I400 to Android 2.3.3 Gingerbread"
I downloaded the same pit and tar files that the guy in the video did. Are the drivers supposed to be anyplace special on my computer? I choose the default when executing the install and it created a folder at C:\Program Files\SAMSUNG. I'm running this on Win XP.
Thanks!
Click to expand...
Click to collapse
The GB files need to be combined if you got them from here.