[Q] T-moUS low level error codes - HD2 General

Please help me to recognize error code while i flashing a radio rom(Radio_Leo_2.15.50.14 for T-Mobile HD2).
Device makes 7 short vibrations... And flashing stops. After that i can only use HSPL boot mode where device showing "Upgrade ROM code error. Please try again"
Only one way to alive device is to flash original ROM. But anyway device booting to winmo from time to time... most of time just stuck on first screen, before radio and spl verson shows.. sometimes it boots to winmo, but not finally and rebooting...

Related

HTC P3300 stuck in boot screen

hi.
i got this p3300 and it doesnt fully turn on.After i press power in remains stuck on the boot screen : the one with the HTC logo and info about the rom:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
I tried to flash rom but it fails at 2 or 3% saying image file corruputed which i think its right because i dont think it was unlocked so you can write any rom you want.
I also tried USPL but that i get "NO devive connected" so i cant unlocked my device to write a proper rom into it.
I did all the above with the device in boot mode (record button+reset).
Any ideea?Pls help.
Thank you!
?
tried flashing with HTC_1.12.405.01_026790_WWE_SHIP says invalid model...
T-Mobile dead loop ?
I have similar problem with my artemis. I have a HTC P3300 from T-Mobile. It started with switching itself out, then it didn't want to boot, then it began to hang on bootscreen and at the moment i cannot start it at all (even the battery is fully charged and it is pluggen in my PC).
I suspect that T-mobile build in a dead loop somewhere in the software or hardware. It looks very suspicious to me that both mdas i had from T-Mobile start to make problems exactly a month or or two after the warranty is expired. and the problems develop in the same way in deteriorating manner.
It could be that the hardware cannot take it anymore and it starts to deteriorate exactly after the second year (handy for two years contracts).
Does anyone similar experiences or anyone solved that problem.
Sorry mates I cannot provide you with any info about my PPC (radio, rom version etc.) because I simply cannot get so far to be able to see that information.
Looking forward hearing from you
Cheerz
Hi, my problem is similar, but I need the ROM in ITAlian.
Information about my cellphone:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
Any ideea how to download this ROM? Pls help.
Thanks, Fernando.
Here the same...any one help?
kappp13 said:
hi.
i got this p3300 and it doesnt fully turn on.After i press power in remains stuck on the boot screen : the one with the HTC logo and info about the rom:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
I tried to flash rom but it fails at 2 or 3% saying image file corruputed which i think its right because i dont think it was unlocked so you can write any rom you want.
I also tried USPL but that i get "NO devive connected" so i cant unlocked my device to write a proper rom into it.
I did all the above with the device in boot mode (record button+reset).
Any ideea?Pls help.
Thank you!
Click to expand...
Click to collapse
Have you tried the CMON USPL? It's on Shady's ROM (the lite one) run this first! Be in Bootloader. Hold the Record Key (left key) and by holding that press Power key to switch on! Then try to Update your ROM

Get stuck in Bootloader

Hi !
My P4350 got stuck in the bootloader when I stied to flash a new ROM
Active sync doesn't recognize the P4350 anymore....
IPL 5.04.0002
SPL 4.10.0000
What should I do now ????
search for bootloader... there are so much threads with the same question
Did it fail during the flashing process? Do you see an error message on the bootloader screen? ActiveSync won't recognize the device unless it is booted up in Windows Mobile. If you can still get into the bootloader reflash the ROM from there. You don't have to flash ROM's connected via ActiveSync; you can do it from the bootloader as well.
It did fail during an flash !!
The only thing on the tri colour screen: is: IPL 5.04.0002 and SPL 4.10.0000
When I try to flash a new rom it gives errors, it starts for 2 seconds and than it stops with an error. (on several occasions different errors ==> one error at the time).
Post some of the error codes you get. Have you tried flashing a different ROM? You may need need to use MTTY if you get a ROM upgrade code message in the bootloader itself.
Ehhhhhhh what is: MTTY if you get a ROM upgrade code message in the bootloader itself.
I have NO idea what you mean.
I had before an TyTN and that was no problem ever (until it died..)
Miep Miep Zoeffff said:
Ehhhhhhh what is: MTTY if you get a ROM upgrade code message in the bootloader itself.
I have NO idea what you mean.
I had before an TyTN and that was no problem ever (until it died..)
Click to expand...
Click to collapse
Is ur device CID unlocked(HardSPLed)?
Miep Miep Zoeffff said:
It did fail during an flash !!
The only thing on the tri colour screen: is: IPL 5.04.0002 and SPL 4.10.0000
...
Click to expand...
Click to collapse
I'm a retard. You don't have HSPL flashed to your device. This is why it keeps failing when you try to flash a ROM. The HTC SPL on your device is blocking you from flashing unsigned (custom) or CID-mismatching ROM's to your device. All you should need to do is flash HSPL and then your custom ROM. Read the Wiki for this device if you need more information.
My phone was provided by Vodafone.
I have now Telfort.
I flashed Vodafone to Canonyang.
Then I tried to put the Dutch back on it and then it got stuck in the Bootloader.
Wasn't it hard SPL than??
Digital Outcast said:
I'm a retard. You don't have HSPL flashed to your device. This is why it keeps failing when you try to flash a ROM. The HTC SPL on your device is blocking you from flashing unsigned (custom) or CID-mismatching ROM's to your device. All you should need to do is flash HSPL and then your custom ROM. Read the Wiki for this device if you need more information.
Click to expand...
Click to collapse
I've tried 2 different HSPL now.
It goes well, even says 100 % on phone AND computer but than it gives error 270 'update error'
What now...
Have you followed this? I know it works for me...
I've seen it, but where do I have to intall the 3 cab files?
Do I have to install them on the microSD card?
Do I have to put them like this .cab or do I need them to unpack them??
please help!
Copy them to your phone, install all three on your phone's memory.
ehhhhhhhhhhhhhhhhh How should I do that ??
Oh right. I'm retarded. You're stuck in the bootloader... Sorry just reading too many threads and getting confused. Have you tried searching for "bootloader" or "Goldcard" in the ROM development forums? There are tons of explanations on how to recover from being stuck in the bootloader.

[Q] Is my HD2 bricked? What can I do?

Hi there everyone!
I installed a NAND Android Rom Dl Desire Z or something... everything was working, but suddendly phone just crashes, and nothing but a white screen appear as soon as HD2 powers on.
The only thing i'm able to do is to go to 3 color mode (hardspl) - but all attempts to flash a wm6.5 rom failed because customruu failed in the middle of the process. freezes at 0% and then appears a communication error in the application.
Conclusion: as soon as phone turns on, only a white screen appears, with nothing written in it.
i've searched for 2 hours in xda and google, nothing similar came...
i've reflashed hardspl3 - sucessfull, but nothing changed, white screen still appears.
i've tried to flash other roms but always freezes at 0%, and appears communication error in customruu application.
I don't know what to do :/
Is there anyone who can help me?
Thank you very much!!
If you can still get into bootloader and you do have hspl installed, try flashing the winmo rom via sd card.
Will do!
I'll post feedback
Start flashing official 1.66(its EU, you need analog to 1024 LEO) WM 6.5 rom from HSPL, than HPSL3, radio with 576 RAM(Radio_2.15.50.14 for example), than MAGLDR112, and after these steps flash Android
Hey there!
I've tried all the methods above indicated.
Flashed a new rom through sd - update failed
Flashed a stock 1.66 Wmo rom but white screen still appears as soon as phone is turned on
Can't downgrade HSPL to 1.42 or so...
Can't do Task 29...
What can I do?
Suggestions?!
Thank you!
Hello
Im thinking maybe your motherboard as many tmous users ?.. just thinking..maybe?? I don't hope it for you
Sent from my HTC HD2 using XDA App
It doesn't make sense :S
I never had any problem with it, and it was running a new Android rom for the second time.. then I take the phone out of the pocket and it is with a white screen...
I can get to the hspl boot but it isn't proving useful...
Any thoughts?

[Q] HD2 From Tmobile will not boot ?!

So my phone froze up , and i rebooted it and its stuck on the "tmobile Stick together logo " where it displays the Radio version and all , and its in that screen for a minute or two and then it goes to a black screen where it says that " You have turned off your phone incorrectly and basicaly the only option that it gives me is to hard reset my phone by pressing " volume up button" .... and i do ! and NOTHING ! HELP
is it from wrong installed ROM, or ?
Can you enter the bootloader?.Firstly, you should do a hard reset to see if that fixes the problem. And did you flash the correct radio or HSPL for your device. If you have not flashed a radio or HSPL, you should enter bootloader and flash HSPL and the radio. If the problem still persists, you should do a Task 29 after flashing HSPL. After doing that, flash the stock ROM again.Once, again, rmb to flash the correct HSPLs, Radios and ROMs for your TMOUS HD2.

[Q]stuck at recovery; serial change to usb

Hi everyone!
I am very sorry for such a n00b-post, but I really cannot find a solution.
The problem:
I recently got a HD2 of a friends who did not use it anymore, because Android suddently stopped working. Now it's stuck at a black screen [A] saying:
aMAGLDR V1.13
Build: Feb 1 2011 03:46:07
by Cotulla 2011
I tried resetting the phone using the red button near the battery, but it did not solve the problem. I am able to boot the HD2 into recovery-mode (colory screen) but then, after connecting to a pc it does not change from "serial" to "usb".
I have installed WMDC on my W7 64-bit system. I have also tried to use "RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship" (from the 4shared "shipped LEO roms"), but none of them recognises my HD2 neither in Recovery nor in the black screen [A].
Is this phone useless? What can I try to revive it?
What might be helpfull: when normally booting, the phone vibrates once during the HTC-screen and 5 times after the black screen [A] appears.
andrejazzz said:
The problem:
Android suddently stopped working. Now it's stuck at a black screen [A] saying:
aMAGLDR V1.13
Build: Feb 1 2011 03:46:07
by Cotulla 2011
I am able to boot the HD2 into recovery-mode (colory screen) but then, after connecting to a pc it does not change from "serial" to "usb".
I have installed WMDC on my W7 64-bit system. I have also tried to use "RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship" (from the 4shared "shipped LEO roms"), but none of them recognises my HD2 neither in Recovery nor in the black screen [A].
What might be helpfull: when normally booting, the phone vibrates once during the HTC-screen and 5 times after the black screen [A] appears.
Click to expand...
Click to collapse
Since you're unable to connect to PC, then you can't re-flash HSPL.
HSPL needed to force flash any shipped WM6.5 ROMs to HD2.
Then the only way is to flash original WM6.5 ROM for your device from uSD.
If you're not sure what CID, just download any HD2 shipped ROMs and try to flash from uSD.
Just be careful not to flash EU's ROM on T-Mobile device!
Extract the ".exe" file, then rename the ".nbh" file into "leo.nbh", copy that to root of uSD.
Power up your device while pressing vol down button.
Don't worry if the ROM refuse to flash, it's just a wrong CID.
But to make sure, connect your device to another clean PC (without android drivers inside, just WMDC), preferably a PC sets for syncing WP7/WP8 devices.
And make sure your device turns on by itself when charger is connected (auto turn on from off state).
That's just to make sure that usb connector is not damaged.
HD2 vibrate 1x at power on, it's normal.
Vibrate 5x after magldr shows up, I suspect something wrong with magldr or the ROM itself (corrupted or something).
Another possibility is some NAND bad blocks.
But if it's vibrate 5x at power on, then you have a bad luck.
The point is, flash the original ROM first.
If it's success, then flash HSPL.
After that, the rest is up to you..
Firstly, I want to thank you very much for your quick and extensive answer!
But I have only one tiny question: are these the ROMS which I can find at http: //www . 4shared . com/dir/22189940/b8552fa0/Shipped_Leo_ROMs.html#dir=MGRa1Cen ? And you mean I should just pick one and try?
You can also find HD2 shipped ROMs here.
Anything that has "TMO" are T-mobile ROMs, otherwise it's EU.
Again, don't flash EU's ROM on TMO devices!
The first 3 digit are the ROM version (1.66, 1.48. etc.), 3.14 is the latest WM6.5 ROM.
The next 3 digit are CID code (207, 404, 707, etc.).
Like I've said, if you don't know which CID for your HD2, then just download all ROMs from different CID then flash it one-by-one using uSD.
Thanks!
So far I have tried the 404 and 162 (edit: and 161, 911), but so far without luck. I'll keep you posted!
Tiny question: is it normal that I cannot shutdown in Recovery Mode?
Perhaps some useful info shown in Recovery:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Correct me if I'm wrong, but it looks like an EU HD2, TMO HD2 are rarely using hynix nand, made around late 2009 or early 2010.
Just try to flash ROM with CID for your friend's country first.
If failed, then try another CID.
There should be one or two info about CID number vs. country somewhere around.
Good luck!
Sent from my Windead Phone 7 using xda app-developers app
At this moment I have tried all the NLD roms with no result. Also I have tried roms from several european countries, but none of them works:/ Might it help if I give the serial number?
And what might be worth saying: my phone turns on when connected to AC power / wall-charger; when connected to charger the "serial" disappears...
Thanks for all your help!!!
Have you try connect to other PC?
When flasing ROM from uSD and failed, what error message you got?
If it's "CID mismatch" or something like that, than it's definitely a wrong CID.
If it's "ROM update error bla bla bla", it's most likely corrupted flash image or the uSD itself (use a small sized uSD, 1gb would be fine).
Even if you flash the correct CID, without removing HSPL first, it would still throw an error message "ROM update error bla bla bla" during flashing Radio.
Then it will restart and retry to flash again on it's own.
By the way, I don't know if there are ways to flash HSPL from uSD.
Or guide on how to make a "gold card".
I sugest you search it.
Worth to try if you couldn't find the correct CID for your device.
CID from serial number?
Yes, back in 2010/11 HTC site provides s/n checking for download the correct ROM.
But now it's gone.
Sent from my Windead Phone 7 using xda app-developers app
Thank you very, very much for helping such a newbie ^^
At this moment, I am able to get into the update-menu: I changed the filename to LEOIMG.nbh. The only problem is that all the Dutch images give the same error: 00018003 : Radio (V2) - FAIL.
What could I do to solve this error? Use the freezer-trick or wouldn't it make any sense?
edit: it does boot when I connect to another W7 pc with WMDC (replies " Not connected" ), only it automatically starts the update-procedure (which fails).
There are no such thing as newbie, that's why we need to learn.
Error 00018003 during Radio flash?
I have no idea what error is that.
But first, are you sure that your friend bought the phone on local shop?
I mean, not imported, or when he/she travel overseas, or has the mainboard swapped at HTC service center.
It happens to me when my second HD2 suddenly has no signal, about 2 years ago.
Brought it to local service center and they swapped the mainboard without telling me.
And the swapped mainboard has CID from 404 (europe), the original was 707 (indonesia).
Okay, back to error something.
WMDC won't recognize the phone unless it's a working WM6.5 device, or a working WP7 device with WP7 SDK + Zune installed on your PC.
Just put the phone into bootloader screen (3 color screen), then connect it to a clean PC.
Does the "Serial" changed to "USB"..?
If it does, reflash HSPL 2.08 using HSPL4 package.
Then flash Radio ROM only, 2.15.50.14 is a good one.
Again, an EU HD2 can use either EU's Radio ROM or T-Mobile's Radio ROM.
But a T-Mobile HD2 can only use a T-Mobile's ROM..!
If the "Serial" doesn't change to "USB" but on your PC makes sound like something is plugged in, open device manager and look for an unknown device (no drivers loaded).
Expand it, what does it says?
To be honest: I am not 100% sure that it is an European (Dutch) phone. What I saw when I opened the phone's back was that the warranty-seals on the screws were molested. I don't think he got the motherboard replaced: way to expensive in relation to a new phone...
The bootloader screen gives now the following text:
RUUNBH
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0X05
CotullaHSPL 0x40
Upgrade ROM error
Please try again
When I connected it to a clean pc, the phone booted and gave another upgrade-error, only this time on a black screen (I got the uSD out the phone).
After booting the phone and connecting to a pc the "serial" does not change to "usb"...
When I tried to install WMDC I get the error "Installationpackage not supported by processor". Seems like bullcrap, but there it ends. No yellow exclamation marks in Device Manager...
I have yet not tried to flash a T-Mobile ROM to the phone. I have tried all the NLD ROM's: 1.66.404 ; 1.48.404 ; 1.66.404 ; 3.14.404 ; 1.66.404 ; 1.43.404
I have yet not tried the other ROMs I downloaded, but I will tomorrow. To start 161 does not work.
Also: I cannot shutdown when in bootloader or MAGDLr, is that correct?
What colour are your call & end key buttons !
if white you have standard EU type model. T-Mobile EU models are same as any EU model & can flash any ROM/Radio
If green & red you have a T-Mobile USA model (TMOUS) & need correct ROM (found in HD2 Wiki)
T-Mobile USA model needs care as if flash wrong radio version you can brick it.
Flashing via SD card should be last choice as first stage of a SD card flash is install of the SPL to standard SPL from the nbh which means you have no CID bypass as HSPL gone.
ideally you need a Windows 7 32bit machine with a known working WMDC setup & try flashing a suitable rom once decided on EU or TMOUS device.
As you have HSPL on your HD2 already it will bypass CID if flash via PC so you can flash any CID code rom.
Try connecting device to PC (with known good WMDC) and use reset button on HD2 to boot to bootloader & see if get any luck in running ROM installer from PC.
If lucky the USB flash issue is PC & drivers rather than hardware on HD2.
I would suspect you have nand issues on HD2 or perhaps worse, if nand sometimes you can get it back if persistent & get something to flash completely.
Thanks MisterB for adds up.
So am I, suspected a nand issue.
The reason I want him to revert back to original SPL & Radio is to make sure that it's a nand related problems, not radio hardware problems.
If he managed to find the correct CID for his phone, he could easily reverts back in case somethings wrong in the future after playing with custom ROMs.
This also happens to my friend's phone a couple months ago.
But in her case, the bad blocks are definitely located where magldr resides, and many more on data partition.
She can flash shipped ROMs completely, but it refuses to boot.
Can't flash a WP7 ROM because magldr freezes when it's loading, can't even bring the menu screen.
She can run a native sd android build for a couple weeks, but then it acting strange again.
Then finally she just gave up and bought another phone.
@andrejazzz:
You can't shutdown on bootloader (3 color) screen.
Remove the battery is the only way to shutdown, or press the reset button to restart.
But you can shutdown/restart or anything else on magldr menu screen.
Press & hold power key right when magldr loads up (before it's start to "go go go").
In addition, you can download WMDC x86 version here, and x64 version here..
He may indeed need try SD flash but I would exhaust all options of USB cable flash via PC first as retaining HSPL will be useful to start with as any generic HTC ROM could be used for the USB cable flash.
If that is not possible then flashing via SD is only viable option & indeed many times only way get over bad boot/nand issues but with all the CID versions for HTC regions & operator branded regions you have a hard job knowing the right one, you could even try the right ROM & as it does not flash overlook it for further testing.
I see he has tried SD flashing but still has HSPL so either SD card is not best suited for nbh flashing or nand/hardware that bad even first stage of flash is not possible.
If I was testing this device & trying recovery I would probably try freezer test to cool device prior flashing & make good effort on USB flash before going on to SD card.
Most well used Android HD2s these days have nand or bga issues to some degree as android works the hardware so much harder than WM6.5.
You really need be sure PC & driver are known good for flashing & if going to SD flashing that SD card is suitable or you will waste a lot of time & effort.
Loads of links & tips for all the software & some threads are in the HD2 Wiki
I apologize for replying so late, but I have had no time: I had a few tests at school
@Mister B: I have a black HD2 with white icons, so I have a european model.
I have installed installed the X86 on a clean 32-bit system, but it does not recognize the phone. I have reinstalled the WMDC on my W7 64-bit system, but still it does not recognize the hd2. I have no other Windows Phones, so I am not able to verify the WMDC-installations.
When I connect to a pc, the phone boots and shows: "Software update failed! Please try again"
@Shadow_Nexus: Correct, that is exactly what happens. I do not completely understand what you mean with "Press & hold power key right when magldr loads up (before it's start to "go go go")", could you please explain?
@Mister B: How could I check if the SD-card might be the problem? It is a 16GB Class 4 Kingston SD. I have tried all the NLD-roms and other versions (random countries, not TMOUS). I have tried the freezer trick with a NLD-rom on a mSD, but it did not work.
Thanks for all your help!
Best using a 2gb or 4gb (8gb max) card for nbh flashing & do a proper fat32 format with something like hp format tool before using it.
link below may help:
http://forum.xda-developers.com/showthread.php?t=681317
Again, thank you very much for your reply. But: do you have any clue what ROM's I should try? I am asking this, because I have already tried all the NLD ROM's I found on the site @Shadow_Nexus gave in post #4, but every one of them returns the same error. Should I switch to another country and try, for example, all German ROM's?
I got my hands on another HD2 and when I connect that one to my pc it show up, named "HTC Sync". The bricked one still does not respond:/ Should I retry all the non-TMO roms I can find?
Edit: My brother "helped" me out and sold the phone...

Categories

Resources