Found a way to tether to my wii - Hero CDMA General

Ok so I spent a few hours messing around last night, and I found a way to tether to my wii. It's probably no good for playing online. I needed to update my homebrew and this worked great for that.
You will need two routers, one of them capable of running dd-wrt. Set the dd-wrt router for client-bridge mode in the wireless tab. In basic setup (in the setup tab), the gateway should be set to the IP of your phone, and the channel and SSID should be set to match your phone. Give the router an IP address that is high in the range set on your tether app. Under setup>advanced routing make sure it is set to router and not gateway. Now with your phone broadcasting, go to the status tab, and the wireless sub-tab. Scroll to the bottom, and click site survey. Your tethered network should show up. Click join. Unfortunately you have to do this every time, as dd-wrt doesn't automatically connect to ad-hoc networks.
Now set up your second router the way you like. Run a patch cable from LAN on the first router to WAN on the second. After it connects, you should have a fully functioning infrastructure network through your tethered connection.
If you don't know about dd-wrt, all the info is online. Read the wiki carefully as you can potentially brick your router if you flash a version that your router can't handle. I'm not responsible if you do this!
I don't know if tomato is capable of client-bridge mode, but you could probably use it instead of dd-wrt if you prefer.
Good luck!
Sent from my HERO200 using XDA App

Very informative!!

I was thinking about this the other day for my PS3. My idea was that couldn't you use your computer as an internet gateway and run a patch cable (Not sure if it'd be a crossover or not) from your computer to a router (into the "Internet" port) and run another patch cable from the router into the PS3?
I didn't bother to try it, but it was an interesting thought considering the only internet connection I have where I live currently is through my phone. The connection does just fine to run Vent+WoW, though.
edit: Maybe it'd work with a switch instead of a router? 'nother thought.

You should be able yo do that, but you wouldn't need a switch or a router, just plug straight in if you use a crossover cable. I think you would need a router if you use patch cables.
The wii doesn't have an Ethernet port so I haven't tried it that way.. I bet its a pain to set up internet sharing in windows though
Sent from my HERO200 using XDA App

Or switch
Sent from my HERO200 using XDA App

It's real easy to share your internet from wifi tether through your computer's ethernet port. and for the wii, you only need a usb to ethernet adapter to use ethernet. (in windows) just enable share connection for your ethernet connection. Plug in. done.
Sent from my HERO200 using XDA App

Related

WMWIFI and Playstation3

Hello,
Long time listner....first time poster.
I've been using WMWIFI for home internet access now for a while. My laptop and desktop have no problems finding my mogul as an access point.
I just purchased a Playstation3 (mostly for the bluray). It has a wireless card built in to access some of Sony's online stuff.
My problem is that the PS3 cannot find my mogul as an access point. Any guesses? I've searched to earth's end, however, it doesn't seem there are many people trying to do what I am...and unfortunately I can't exactly call sprint and ask them.
Thanks for any help.
Found the answer...the PS3 will not connect to an Ad-hoc network...
Reported to not work
Nintendo DS
Nintendo Wii
PlayStation Portable
Unable to connect to a device providing internet using ad-hoc mode.
Do ya'll think that there is a way around this?
I don't have any other internet access (except for the mogul) but would like to get the PS3 connected.
i'm sure theres a way to rebroadcast from the PC
hymanr said:
Found the answer...the PS3 will not connect to an Ad-hoc network...
Reported to not work
Nintendo DS
Nintendo Wii
PlayStation Portable
Unable to connect to a device providing internet using ad-hoc mode.
Do ya'll think that there is a way around this?
I don't have any other internet access (except for the mogul) but would like to get the PS3 connected.
Click to expand...
Click to collapse
The psp can connect to an Ad-Hoc network (at least the last time I tried), don't know about the others. I just know under network settings on the psp you have to change it to ad-hoc mode.
Yes it can be done. you need a laptop or a desktop to act as a middle man.
If your desktop or laptop has a wireless / wired port, simply share the internet conenction from your phone to your PC.
plug in a wire from the ps3 to the PC
highlight the wireless icon, and the wired icon in your network manager and right click and hit bridge network connections.
it will work after that.
sfld said:
Yes it can be done. you need a laptop or a desktop to act as a middle man.
If your desktop or laptop has a wireless / wired port, simply share the internet conenction from your phone to your PC.
plug in a wire from the ps3 to the PC
highlight the wireless icon, and the wired icon in your network manager and right click and hit bridge network connections.
it will work after that.
Click to expand...
Click to collapse
If you have a wireless router,that should make it all work. Set your mogul to connect to the wireless router and set the router to be 192.168.0.2 instead of its default. Now setup your devices with a static IP,on the same subnet and set the default gateway to be 192.168.0.1 (your moguls ip). In the earlier versions,this just works as is.
In the latest version,you will need to set some other settings on the phone as well. Go into your phones wifi settings and set the wifi adapter to 192.168.0.1 (earlier versions of wmwifirouter set this as the default,but the newer one is more flexible,so you need to specify this) Now,connect your wifi to your routers network. Next launch wmwifirouter. Clear the check mark next to dhcp allocator and adhoc netoworking. Network block should be set to the 192.168.0.x subnet. The router wont actually be used as a router,just as a network access point. Your mogul is actually the router. The clients are setup as before,with static IPs with a default gateway of 192.168.0.1.
This is how I connect my computer to the internet. I expect that it should work with any device that can be set with a static IP.
Thank you pflatlyne...
I have a wireless router but have not been using it as my computers can access the mogul directly. I will try your set up tonight.
Hopefully I can follow your instructions well enough to get it set up.
Thank you!!
WMwifiRouter and Xbox360
This did work with my 360 and WMwifiRouter. Had to config for my settings but it works!!! Yippee
EDIT
In case anyone asks, I did'nt need anything except my phone and 360. No router, or computer. Just fired up my wifi and entered the settings in my 360. It didn't see it, but it allowed me to edit my settings. I don't know about the PS3, wouldnt mind having one though. :..(
Hmmm....I still can't get it to work..
I'm not the most literate when it comes to how to do this.
Any chance of a detailed walkthrough on what to connect to what?
I have a desktop, an Actiontec wireless router, a wireless adapter for my desktop, mogul, and playstation....
Yes a step by step would be great. I have been trying to get the wireless router idea to work with no luck.
Mine works
What I did was what the other guy said with bridging the connection. once you connect your mogul to the computer and get online through the pc, connect an ethernet cable from your pc to the wifi routers main plug.
go to network connections
highlight your internet connection for the mogul and the one for the ethernet ( on my pc it is defaulted as internet connection 11 for the mogul and 12 for my NIC card) right click the highlighted connections and click bridge. connect the ps3 to one of the available hub slots and your ps3 should connect n/p.
IF YOU DON'T HAVE A ROUTER...
you must purchase a cross over cable to get an internet connection directly from your pc to your ps3. the method is the exact same as above except no router.

Help setting up wireless/wired/PoE/server network

So i am trying to setup my home network and want to make sure i do it in the most efficient way and so everything sees everything on the network. Here are my basic needs:
-wireless
-wired connections- need about 6 to 8 connections (most wont be used but eventually might be down the road)
-one of the wired connections needs PoE (power over ethernet) to run the security webcam
-i also would like to setup a small home server (i started setting up amahi on an old machine but am open to other alternatives- preferably free or cheap)
so right now i have the cable modem connected to an 8port switch which has four poe capable ports on it. connected to this is the lines running to the different rooms. one of these lines goes to the wireless router up in my computer room. my desktop computer is connected to this router (it has 4 wired ports on it). Right now my desktop cant find the security webcam because it says its not on the network (probably because wireless router is between computer and switch that webcam is connected to). also i am having issues with the google tv box finding the computer to share media.
so what order should i connect everything together in (modem/switch/router/server) and are there any settings i need to do on them so they all work together as one network instead of 2 or 3 networks all strung together?
Thanks!
Modem to router to switch.
Sent from my XT883 using xda app-developers app
Thanks. Should I hook up server computer to router or switch?
Either. The ports on the router are a switch.
Sent from my XT883 using xda app-developers app

Xbox Live Moderate NAT on Hotspot/Tether

Is there a clear tutorial on setting the NAT to open on Xbox Live? I'm tethering off my Verizon 4G LTE phone.
Of course theres a way.
juryben said:
Is there a clear tutorial on setting the NAT to open on Xbox Live? I'm tethering off my Verizon 4G LTE phone.
Click to expand...
Click to collapse
I was never able to find one that was complete... through trial and error I found a solid usb method. Now my only problem is this POS LG Revolution with no man support or ROMs. Seems I have to tether through EasyTether to maintain a solid connection (anyone know why?) otherwise it poops out after a couple minutes randomly which sucks because I've had my best tether 4g speeds through 3 rarely talked about apps, Tether Pop-Up and Auto-Usb Tether and SVTP no idea why but they kick the crap out of PDANet, Clockwork Tether, EasyTether. With the auto enablers / widgets I get 18-40DN / 6-12UP MB/S on speedtest.net the only way my tethering speed came close to matching my true phone 4g speeds the most Ive ever seen from the others was 7mbs dn 3up thats with easytether. So first find a tethering method that works the fastest with a solid connection (you need it otherwise constant disconnects and probation waiting for matches).
Now share your connection via pc/mac network card/ethernet cable to a Router (it must support an NZB Server)'s internet port. Set your xbox up to be a set IP address mines 192.168.1.4. leave everything else blank except dns = google for phone, pc and xbox network settings. Then login to your router generally under WLAN Setup you'll find "Default DMZ Server" enter your Xbox IP address in fields. Check to make sure MTU Size is 1500 and NAT Filitering "Open". I disable SIP ALG too if optional. Check to make sure your connection from PC is being shared and used as gateway ect in your main status and thats it. Connect to router via wireless or ethernet (faster). DMZ basically creates a port server for the xbox-router any port the xbox wants open nzb opens it (was what I understood). If your still not getting your xbox to say Open NAT make sure ips match router DMZ and xbox (dhcp crap messes it up sometimes), start opening ports on the router, pc and android for xbox you can get list of ports for COD via google and portforward on android and complete firewall bypass on pc can help too. You can achieve OPEN by simply getting all ports necessary but DMZ method much easier. As far as I know you need a DMZ capable Router you cannot WiFi tether to xbox and get open or any other way without a router to my knowledge.
gigilie said:
I was never able to find one that was complete... through trial and error I found a solid usb method. Now my only problem is this POS LG Revolution with no man support or ROMs. Seems I have to tether through EasyTether to maintain a solid connection (anyone know why?) otherwise it poops out after a couple minutes randomly which sucks because I've had my best tether 4g speeds through 3 rarely talked about apps, Tether Pop-Up and Auto-Usb Tether and SVTP no idea why but they kick the crap out of PDANet, Clockwork Tether, EasyTether. With the auto enablers / widgets I get 18-40DN / 6-12UP MB/S on speedtest.net the only way my tethering speed came close to matching my true phone 4g speeds the most Ive ever seen from the others was 7mbs dn 3up thats with easytether. So first find a tethering method that works the fastest with a solid connection (you need it otherwise constant disconnects and probation waiting for matches).
Now share your connection via pc/mac network card/ethernet cable to a Router (it must support an NZB Server)'s internet port. Set your xbox up to be a set IP address mines 192.168.1.4. leave everything else blank except dns = google for phone, pc and xbox network settings. Then login to your router generally under WLAN Setup you'll find "Default DMZ Server" enter your Xbox IP address in fields. Check to make sure MTU Size is 1500 and NAT Filitering "Open". I disable SIP ALG too if optional. Check to make sure your connection from PC is being shared and used as gateway ect in your main status and thats it. Connect to router via wireless or ethernet (faster). DMZ basically creates a port server for the xbox-router any port the xbox wants open nzb opens it (was what I understood). If your still not getting your xbox to say Open NAT make sure ips match router DMZ and xbox (dhcp crap messes it up sometimes), start opening ports on the router, pc and android for xbox you can get list of ports for COD via google and portforward on android and complete firewall bypass on pc can help too. You can achieve OPEN by simply getting all ports necessary but DMZ method much easier. As far as I know you need a DMZ capable Router you cannot WiFi tether to xbox and get open or any other way without a router to my knowledge.
Click to expand...
Click to collapse
Thanks, I appreciate it! One question, is it possible without a router? Just bridging PC to Xbox?
When you're using this kind of a method, your phone provider is the NAT. You can't really get around it because they control it. Not you.
However many phone providers will let you pay extra for a public IP address and then you'll have an open NAT.
I've tried just about every possible method to grt open NAT through my phone with the wifi tether app.. PC has wireless adapter connected to my phone.. Etherney cable from LAN port to the routers modem plug.. Ethernet cable from router to ps3.. I can't login to my router to change any of the settings for some reason.. I have a Netgear and my web browser keeps saying it can't find the page..
Sent from my SPH-D710 using Tapatalk 2

Tether to Router?

So I can use my standard USB cable and tether to the laptop and have net connection on lappy. Same with desktop. USB tether works just the same as wifi tether. What about getting a micro USB to RJ45 (ethernet) cable and tethering to the internet in jack on my router. Would that put the net signal on the router like a modem would?
Chopstix9 said:
So I can use my standard USB cable and tether to the laptop and have net connection on lappy. Same with desktop. USB tether works just the same as wifi tether. What about getting a micro USB to RJ45 (ethernet) cable and tethering to the internet in jack on my router. Would that put the net signal on the router like a modem would?
Click to expand...
Click to collapse
Or you could get a wireless adapter for your Desktop. That's what I did. Now I can stream Amazon Prime on my Xbox 360, and PC game at the same time.This is what I have and works like a charm.
Good luck.
Oh my desktop is already wireless enabled, that's not an issue... Been running the house off the phones for a couple years... Just gave up a little bit when I got rid of cable interet. Whole house networking to other computers in the house, had to plug the wireless printer back into the desktop, it's no longer a network printer, etc.... was just toying with the idea and wondering if it would work is all.
Actually, in looking at the micro usb - rj45 adapters, I don't think it will work. Those are actually ethernet adapters, like adding a network card to a slot on a pc. Made for taking a net signal FROM a network, not sending one TO it.
Correct me if I'm wrong, but can't you just get a compatible wireless dongle (Something you would use for sniffing/injecting packets) and use it as an access point so you can broadcast the signal throughout the house?
Another thing you can do is pick up a router that you can install Tomato or DD-WRT on and use it as a wireless client bridge. It would connect to your phone, and again, broadcast that signal through the house.
Chopstix9 said:
So I can use my standard USB cable and tether to the laptop and have net connection on lappy. Same with desktop. USB tether works just the same as wifi tether. What about getting a micro USB to RJ45 (ethernet) cable and tethering to the internet in jack on my router. Would that put the net signal on the router like a modem would?
Click to expand...
Click to collapse
DJNads said:
Another thing you can do is pick up a router that you can install Tomato or DD-WRT on and use it as a wireless client bridge. It would connect to your phone, and again, broadcast that signal through the house.
Click to expand...
Click to collapse
Correct. Assuming the phone would even operate in this manner (I've never tried but sounds like a great idea!), you'd need a router that is capable of operating in bridged mode/wireless bridge/access point mode (may be labeled as either of them). You'd then have to configure the router to said bridged mode. An easier route (and possibly more expensive) would be to purchase just an access point.
MrHyde03 said:
Correct. Assuming the phone would even operate in this manner (I've never tried but sounds like a great idea!), you'd need a router that is capable of operating in bridged mode/wireless bridge/access point mode (may be labeled as either of them). You'd then have to configure the router to said bridged mode. An easier route (and possibly more expensive) would be to purchase just an access point.
Click to expand...
Click to collapse
I may have an old WAP in my junk closet. A router that can bridge may work but first thing I think I would need is a router or WAP that has a USB connection on it.... I'm looking to plug the phone into the router to provide the internet signal instead of a cable/dsl modem, creating a typical LAN ... I can still use the LAN in-house sans the net connection. Just a pain to disconnect from one network (phone hotspot) and connect to another (netless LAN) for file transfers network printing etc ...
Chopstix9 said:
I may have an old WAP in my junk closet. A router that can bridge may work but first thing I think I would need is a router or WAP that has a USB connection on it.... I'm looking to plug the phone into the router to provide the internet signal instead of a cable/dsl modem, creating a typical LAN ... I can still use the LAN in-house sans the net connection. Just a pain to disconnect from one network (phone hotspot) and connect to another (netless LAN) for file transfers network printing etc ...
Click to expand...
Click to collapse
You shouldn't need to physically connect your phone to the router at all. Depending on what router you get, it should be able to pick up the wireless signal from your phone's hotspot and rebroadcast it as its own network.
Edit: And honestly, I'm not sure connecting the phone via usb to the router would even share the connection. That router doesn't have the drivers needed for that to work.
To the OP, off topic question but what did you have to do to activate wi fi tether? your sig, tells me that your on stock and can still do it, yes? thanks!
Side note, it's been awhile but when I moved into my apartment I had no internet for a few days.
I did the USB wired tether to a laptop, then the laptop I think I enabled ICS/internet connection sharing and then connected with rj45 to a router, and it shared that as the WAN connection.
motrinHD said:
To the OP, off topic question but what did you have to do to activate wi fi tether? your sig, tells me that your on stock and can still do it, yes? thanks!
Click to expand...
Click to collapse
What part of my sig tells you I am on stock?
I've done both these things. I've taken my cell and flashed a router with dd-wrt and set it up as a repeater bridge but that means that only the computers near that router gets internet, unless your house is wired for ethernet (or using wireless). My current setup is having the phone tethered to a computer running Zentyal linux. This is a cool distro that can replace a 2008 Small business server in a work environment but it does the trick for my router at home. I had it running on an old P4 and recently graduated to a Zotac Zbox Mini ID41 which is tucked away behind my TV. I set up the computer to hand out dhcp and be the router and gateway. When i plug in my cell in tethering mode, zentyal recognizes it and i set that USB device as external WAN. It usually takes some getting used to and about a minute to normalize after the phone is unplugged and taken on the road. This has worked for me so far but when i'm at work, no internet at home. I'm currently attempting to talk my workplace into letting me subsidize a Verizon Jetpack i can leave home which will do the same job.
As a side note, i live in rural WI and we only have Satellite internet as a choice, which really stinks as both carriers have a bandwidth cap which we were constantly hitting two weeks into the billing cycle. They then throttle you down to less than a meg until your billing cycle renews.
We RV all summer most years and I use WiFiRanger gear to network our 5th wheel. That way we can grab a WiFi AP if one is available and the credentials are known or I HotSpot my phone and the Router grabs the phone's WiFi AP and we are good to go.
If you are stationary and only intend to use the phone's HotSpot as a WiFi AP then WiFiRanger's GO2 should do the trick. They are currently working on a firmware upgrade that will allow some great bandwidth monitoring and device usage controls. Their price is comparable to most full featured routers being offered but not cheap.
I am a satisfied user and Beta tester of their equipment, not an employee or representative. We use several of their offerings to maximize our capabilities on the road.

let's figure out a way to choose a wireless network connection over a wired one

I've searched everywhere online, and it seems that the only way to do this is to remove the ethernet cable from either the router/switch/ATV.
can anyone think of any ideas to get around this? it probably won't work, but I'm downloading different network manager apps in the hopes that it would allow me to just this. I have a feeling that this won't work, but it's worth a shot.
shutterslaps said:
I've searched everywhere online, and it seems that the only way to do this is to remove the ethernet cable from either the router/switch/ATV.
can anyone think of any ideas to get around this? it probably won't work, but I'm downloading different network manager apps in the hopes that it would allow me to just this. I have a feeling that this won't work, but it's worth a shot.
Click to expand...
Click to collapse
why do you wan't to use wireless connection over wired? do u have tried to also connect to wifi while connected wired?
if it's because app only use wifi and you are rooted and have xposed installed u might use the fake wifi module
http://forum.xda-developers.com/xposed/modules/app-fake-wifi-connection-t2800416
installed via xposed. works like charm for me...
The best connection is always the connection that gets used. A wifi connection is not as stable of as powerful as an ethernet connection and thats why computers always use the ethernet connection over the wifi connection. If you wanna use wifi, disconnect the ethernet cable. Its the same with mobile devices, if you have your mobile data on and wifi on, it will more than likely pick the wifi connection, cause wifi is usually better than mobile data. My mobile data never ever kicks on over my wifi connection.
shutterslaps said:
I've searched everywhere online, and it seems that the only way to do this is to remove the ethernet cable from either the router/switch/ATV.
can anyone think of any ideas to get around this? it probably won't work, but I'm downloading different network manager apps in the hopes that it would allow me to just this. I have a feeling that this won't work, but it's worth a shot.
Click to expand...
Click to collapse
As others have said, wired is preferred over wireless for multitude of reasons. But, if you do want to use Wifi when you have an ethernet cable hooked into FTV, you can use this from adb shell:
To bring down your wired network card: busybox ifconfig eth0 down
To bring back up: busybox ifconfig eth0 up
Once you bring down your wired connection, you should be able to navigate to your wireless settings on FTV and go wifi without physically disconnecting your wired cable.
This will not persist across reboots. You will need to include appropriate code in your startup script to make that happen.
thanks everyone! I'm going to try all of these after I eat.
I agree, a wired connection is without a doubt better and preferable. However, the building I live in only offers a free wifi connection that is installed throughout the building. I'll be looking to see if I can get my own internet connection soon.
When I have the AFTV connected through ethernet, and I want to SSH, or ADB into the AFTV from my computer, I cannot for some reason. I figured it would work since the wifi and wired connections are technically the same network, right? I also can't use any remote apps from my phone since the phone is on wireless.
I usually disconnect the ethernet cord, and create a wifi connection from my macbook, or tether my connection from my phone and connect my laptop and ATV to that network. I'm just looking for a way to be able to do all of this without having to get up and take out the ethernet cord everytime. It's not that I'm lazy, I just have this external fixation on my leg from an injury.
Xfinity app
I used the xfinity app to stream cable on my aftv... I got tired of buffering so switches to ethernet.. The app thinks im out of my wireless network... Can we spoof wifi on this like some of the old apps for jailbroken iphones or in xposed? . I too want to trick my box into thinking ethernet is wifi so xfinity wont think im not on my network...
so let me see if i have this right:
1) you want AFTV to use wireless for internet
2) you want AFTV to use wired for administration/etc
if so --- setup wireless as usual, let it dhcp and do its thing....and setup your WIRED manually leaving the default gateway blank or unconfigured. This will force all traffic bound for hosts not available via wired interface to the WLAN (and the internet).
since the AFTV and your laptop/etc are wired and on the same subnet, they don't need to be routed to communicate and they will work fine. Any other traffic need to be routed, and the only outbound route your AFTV will know is via the wireless interface.
for example:
AFTV wireless: 192.168.0.10, gateway 192.168.0.1 (or whatever dhcp gives you)
AFTV ethernet: 10.10.10.1 gateway (blank)
Laptop wireless: 192.168.0.11, gateway 192.168.0.1 (or whatever dhcp gives you)
laptop ethernet: 10.10.10.2 gateway (blank)
you can then use the 10.10.10.x addresses via ethernet to communicate via local ethernet without disturbing the default internet route and internet access.
mattvirus said:
so let me see if i have this right:
1) you want AFTV to use wireless for internet
2) you want AFTV to use wired for administration/etc
if so --- setup wireless as usual, let it dhcp and do its thing....and setup your WIRED manually leaving the default gateway blank or unconfigured. This will force all traffic bound for hosts not available via wired interface to the WLAN (and the internet).
since the AFTV and your laptop/etc are wired and on the same subnet, they don't need to be routed to communicate and they will work fine. Any other traffic need to be routed, and the only outbound route your AFTV will know is via the wireless interface.
for example:
AFTV wireless: 192.168.0.10, gateway 192.168.0.1 (or whatever dhcp gives you)
AFTV ethernet: 10.10.10.1 gateway (blank)
Laptop wireless: 192.168.0.11, gateway 192.168.0.1 (or whatever dhcp gives you)
laptop ethernet: 10.10.10.2 gateway (blank)
you can then use the 10.10.10.x addresses via ethernet to communicate via local ethernet without disturbing the default internet route and internet access.
Click to expand...
Click to collapse
it's actually the other way around.
1) I want AFTV to use wired for internet
2) I want AFTV to use wireless for administration/etc
I can't ssh/adb/etc without taking the ethernet cord out and connecting the AFTV and laptop to the same wireless network. I was hoping for a way to shut down the ethernet connection, so I can connect over wifi without taking out the ethernet cord. The AFTV won't let you connect to a wireless network if the ethernet cord is plugged in and connected.
I actually figured out a way to do what I need without taking out the ethernet cord.
What I do is:
1) SETTINGS (not the one that came with the AFTV, it's a settings.apk I installed)
2) under WIRELESS & NETWORKS click 'More...'
3) TETHERING & PORTABLE HOTSPOT
4) CONFIGURE WI-FI HOTSPOT
5) activate the hotspot and connect to that network from the laptop
dbdoshi said:
As others have said, wired is preferred over wireless for multitude of reasons. But, if you do want to use Wifi when you have an ethernet cable hooked into FTV, you can use this from adb shell:
To bring down your wired network card: busybox ifconfig eth0 down
To bring back up: busybox ifconfig eth0 up
Once you bring down your wired connection, you should be able to navigate to your wireless settings on FTV and go wifi without physically disconnecting your wired cable.
This will not persist across reboots. You will need to include appropriate code in your startup script to make that happen.
Click to expand...
Click to collapse
just gave that a try. now I have two methods to achieve what I looking to do. appreciate it!

Categories

Resources