[Q] HSPA+ or 3g or 2g setting - G2 and Desire Z General

hi i came from a mytouch slide and i was able to set the network to 2g or 3g or even both at the same time. is there a way to turn off 2g on the g2? or even turn off HSPA+ and only use 3g? i've been looking around and can't seem to find anything on this. i'm not rooted but if i need to be that will be fine.

Have you tried dialing#*#*4636*#*#?
Sent from my CyanogenMod powered G2.

Yes. The easiest way is to go to the phone dialer and type in:
*#*#4636#*#*
This will take you to a menu.
1) Choose "Phone Information"
2) Scroll down and there is a drop down menu.
Default is "WCDMA Preferred" --- Which is 3G/2G with 3G preferred.
You may choose WCDMA only for 3G only or Edge for 2G only.

I don't think you can turn off hspa+ but you can just go to settings ---- wireless--- mobile networks--- and just check 2g only for edge and leave it off for 3g/H+
Sent from my HTC Vision using XDA App

ischagoi2 said:
hi i came from a mytouch slide and i was able to set the network to 2g or 3g or even both at the same time. is there a way to turn off 2g on the g2? or even turn off HSPA+ and only use 3g? i've been looking around and can't seem to find anything on this. i'm not rooted but if i need to be that will be fine.
Click to expand...
Click to collapse
... hspa+ ***IS*** 3g.... so you apparently want to choose between 3g and 3g? Can't happen.

it can be done but requires a reboot. You will need to add/change the setting "hsxpa=0" in the build.prop. this will remove the "4g" also you may need to change lines that referance the ril libraries to remove the reference to "rilswitch". But that might just be with cm6...
Sent from my HTC Vision using XDA App

Related

Can't get HSDPA on T-Mobile UK

As the title says, I'm not getting HSDPA in areas where I was getting it before with my Galaxy S. I only ever get 3G and it is driving me nuts!
Is there anyway to change it to allow HSDPA on the phone? It is noticably slower, particularly streaming videos.
I'm on T-Mobile UK with the web & walk+ tariff.
Are you running the stock rom?
If so - afaik you get 3G for both 3G and HSDPA. Check your connection type in "About Phone" in settings - should be under "status".
Highland3r is correct. HSDPA is a 3G technology, and the stock ROM on the Nexus S does not differentiate it in the connection type display. You are most likely connected to your provider's HSPA network, your phone simply doesn't advertise that fact.
T mobile UK, uses a different band
it uses the same frequency as the 3G from ATT in USA
Nexus S is an AWS band phone
I'm having a similar issue with my Nexus S on Orange UK. I have to manually force it to use HSDPA in the engineer's menu but after a certain amount of time it defaults to UMTS.
My brother-in-law's Galaxy S has a constant HSDPA connection.
Sent from my Nexus S using XDA App
I'm on vodafone in the uk and I get HSPA mostly all of the time, u guys are right, it says 3g in the bar at the top of the screen but looking deeper it is in actual fact HSPA.
Sent from my Nexus S using XDA App
it's been like this since Android 2.3. They only display 3G whether your using 3G or HSDPA... they are essentially the same.
Therefore they just show 3G...
I prefer it to show me 3G or H or UMTS ( sometimes on UMTS aswell and still shows as 3G )
I am currently on CM7 and it does display H most of the time as the coverage is pretty good where I am. This has been the case even before I rooted the phone.
Thanks for the info guys, like Highlan3r suggested it has HSDPA in the status menu but 3G in the notification bar! It is the stock ROM also, just found it a bit unusual since changing from the Galaxy S only a week ago but now I know.
Thanks again!
Just to clarify, my Nexus S shows UMTS under status, even when a data connection is active. If I force it onto HSDPA by selecting WCDMA only in the engineer's menu, it again reverts to UMTS after a certain length of time.
My brother-in-law's Galaxy S has constant HSDPA connection on the same network. We are both using stock roms.
Sent from my Nexus S using XDA App
you will only see HSDPA when there is network traffic. If the connection's idle, it goes back to display UMTS (to save battery and network resources)
Nexus-S said:
Just to clarify, my Nexus S shows UMTS under status, even when a data connection is active. If I force it onto HSDPA by selecting WCDMA only in the engineer's menu, it again reverts to UMTS after a certain length of time.
My brother-in-law's Galaxy S has constant HSDPA connection on the same network. We are both using stock roms.
Sent from my Nexus S using XDA App
Click to expand...
Click to collapse
Are you using a custom ROM of any kind? It _could_ be an issue with the APN's setup - CM7 for example doesn't set a default APN on my phone which seems to cause mobile data connectivity problems until a default is set/the extra crap is removed.
<edit>
You're probably best starting a new thread for this btw as it's likely to be a different issue to the ops
</edit>
And now after the 2.3.3 update it switches to HSDPA perfectly.
Sent from my Nexus S using XDA App

Network Mode - Verizon

I noticed that by default this phone is setup to use "Global" as the preferred network mode. I'm thinking that means it'll try to use CDMA, LTE, and GSM networks. I noticed there's a setting for "LTE / CDMA" and I'm thinking this setting may save some battery because the radio software wont try to use the non-existent GSM for Verizon.
Anyone play around with this setting and notice a difference? I just switched to LTE / CDMA. I lost data until I rebooted and now everything is working fine. It's odd that it was set as Global to begin with.
I did the same thing you did. I notice no difference but it does work fine. I also tried fooling around with lte on/off app. Is there a simple widget that can be used to toggle between 4g and 3g? If I know i won't be using the phone for a while i would like to switch to 3g to save battery.
skinien said:
I noticed that by default this phone is setup to use "Global" as the preferred network mode. I'm thinking that means it'll try to use CDMA, LTE, and GSM networks. I noticed there's a setting for "LTE / CDMA" and I'm thinking this setting may save some battery because the radio software wont try to use the non-existent GSM for Verizon.
Anyone play around with this setting and notice a difference? I just switched to LTE / CDMA. I lost data until I rebooted and now everything is working fine. It's odd that it was set as Global to begin with.
Click to expand...
Click to collapse
Bump.
Sent from my HTC One XL using xda premium
recDNA said:
I did the same thing you did. I notice no difference but it does work fine. I also tried fooling around with lte on/off app. Is there a simple widget that can be used to toggle between 4g and 3g? If I know i won't be using the phone for a while i would like to switch to 3g to save battery.
Click to expand...
Click to collapse
You can download an app called Phone Info -- open it up and go down to Network mode, select CDMA (Auto) that will force 3G only.
It will remain until you reboot.
I used to do this with my OG HD and it did save quite a bit of battery but in my semi-scientific tests the difference on the Maxx HD is almost nonexistent, certainly not worth the reduction in speed or the inability to use data and voice simultaneously.
I don't know if you noticed but, data and voice simultaneously is possible even in 3g mode with the razrHD Max. The greatest android phone verizon has ever offered.
Sent from my DROID RAZR HD using xda premium

Force LTE?

Sometimes I drop to 3G in my home 4G area. Turning the phone off and back on usually does the trick but is there another way to keep the 4G connection?
Sent from my XT907 using xda app-developers app
zombolt said:
Sometimes I drop to 3G in my home 4G area. Turning the phone off and back on usually does the trick but is there another way to keep the 4G connection?
Sent from my XT907 using xda app-developers app
Click to expand...
Click to collapse
I believe you can set the phone to only receive CDMA and LTE in the Mobile Networks option of the settings (in the more section)
You can also set it to receive only GSM, GSM and CDMA, or all available networks.
Leraeniesh said:
I believe you can set the phone to only receive CDMA and LTE in the Mobile Networks option of the settings (in the more section)
You can also set it to receive only GSM, GSM and CDMA, or all available networks.
Click to expand...
Click to collapse
CDMA=3G, LTE=4G. Right? Since I am on the Verizon network, the only circumstances that I would connect to GSM is if I left the USA, right? I wonder if there's a way to isolate LTE connectivity and turn off 3G all together..
Sent from my XT907 using xda app-developers app
zombolt said:
CDMA=3G, LTE=4G. Right? Since I am on the Verizon network, the only circumstances that I would connect to GSM is if I left the USA, right? I wonder if there's a way to isolate LTE connectivity and turn off 3G all together..
Sent from my XT907 using xda app-developers app
Click to expand...
Click to collapse
You on stock or a custom ROM?
That sounds like a radio problem tbh.
You can't use LTE only - in fact, LTE requires a CDMA or GSM base for stuff like phone calls so it always has to be connected to 3g or 1x.
There's a possibility that switching airplane mode or pulling your SIM out would force LTE to reconnect
Solution: Yes you can force lte
I'm not a engineer or a radio analyst but I do believe what the previous post says about LTE needing CDMA is completely wrong - it certainly doesn't need to have CDMA or any other radio band to effect LTE. That being said, LTE is BASED off of 3G CDMA. But again, I may be inaccurate, however I think the "proof is in the pudding"......HOW TO FORCE TO LTE (ONLY)
1. Open up your phones dial pad
2. Dial *#*#4636#*#* (An app with the title "Testing" should open automatically... but not 100% sure. If it doesn't open auto hit dial....
3. Select "Phone Information"
4. Scroll down the phone information page, you should see the first button that says "Turn off radio"..... We want to focus on the item right above that. By default it's set to "LTE/CDMA/EvDo/GSM/WCDMA"
5. Click on that which should provide a drop down list, with specific radio bands.
6. In your case select "LTE Only"
7. Profit!
FYI: IN "LTE Only" mode you will not be able to make or receive calls - this is good for DATA only. You can manually reset back to default mode but regardless every time your phone reboots it will go back to default.
Well yeah that's true. Not really sure if vzw will let you connect though. But yeah no calls or text
Sent from my XT907 using Tapatalk 4

Network coverage issues or device ?

I'm having some problems with my G2 - I don't have good 3G coverage especially inside and my phone keeps dropping calls when on 3G. It seems the software doesn't reconnect that fast and doesn't switch to 2G when the 3G signal is too low. Is there any way to change the preferred network and stop the device being so agressive at keeping 3G connection?
Settings/networks/tethering & networks/mobile networks/network mode/GSM only.
I already know that. It is the most unhelpful advice to give. I have to constantly go into settings and change that? No way. It isn't in the notification toggles which is really odd. Any idea how to add it? I feel my G2 has some radio issues.
Sent from my LG-D802 using Tapatalk
axlastro said:
I already know that. It is the most unhelpful advice to give. I have to constantly go into settings and change that? No way. It isn't in the notification toggles which is really odd. Any idea how to add it? I feel my G2 has some radio issues.
Sent from my LG-D802 using Tapatalk
Click to expand...
Click to collapse
Well if you're going to be like that then there's no wonder why there aren't a stream of responses on here with people trying to help you out.
Just remember, you're the one with the problem, so you may want to be a little nicer to those that try to give you help.
I'm sorry about that, but there wasn't a stream of responses in the first place. He was just stating the obvious, and the obvious is that the G2 doesn,t have a shortcut to switch between 2g and 3g. I'm just trying to figure out a way to do that, but all the apps that claim to do that and they are too many of them, just don't work. I'm thankful for any help, don't get me wrong.
Sent from my LG-D802 using Tapatalk
axlastro said:
I'm sorry about that, but there wasn't a stream of responses in the first place. He was just stating the obvious, and the obvious is that the G2 doesn,t have a shortcut to switch between 2g and 3g. I'm just trying to figure out a way to do that, but all the apps that claim to do that and they are too many of them, just don't work. I'm thankful for any help, don't get me wrong.
Sent from my LG-D802 using Tapatalk
Click to expand...
Click to collapse
There isn't a solution as simple as hitting a switch, but you can try the following:
Go into your Dialer and tap in *#*#4636#*#*
This will take you into the Testing Menu
Select 'Phone Information'
Then about half way down you will have a drop down where you can "Set preferred network type:"
This will allow you to choose whether to use 2G or 3G, but more important to your case you can choose how it will react if signal strength is low.
You probably want to select something like "GSM auto (PRL)"
Bare in mind though that this option will reset itself back to original setting each time you reboot the device.
Now I don't know if this will solve your problem, but it is worth testing out.
Here's a list detailing the main available options:
WCDMA preferred - The GSM phone is capable of using both 2G and 3G data communication and when signal strength is low 3G is favored more.
GSM only - The GSM phone is capable of using only 2G data communication. When the 2G signal is too low you get nothing at all.
WCDMA only - The GSM phone is capable of using only 3G data communication. When the 3G signal is too low you get nothing at all.
GSM auto (PRL) - The GSM phone is capable of using both 2G and 3G data communication and when signal strength is low 2G is favored more.
CDMA auto (PRL) - The CDMA phone is capable of using both 2G and 3G data communication and when signal strength is low 2G is favored more.
CDMA only - The CDMA phone is capable of using only 2G data communication. When the 2G signal is too low you get nothing at all.
EvDo only - The CDMA phone is capable of using only 3G data communication. When the 3G signal is too low you get nothing at all.
GSM/CDMA auto (PRL) - Some phones are equipped with both GSM and CDMA capabilities. This setting appears to just have the phone attempt to stay connected to the data communication type that works the best.
Unknown - If none of the above fit or the phone is acting weird as far as connecting to the carrier, you will see your preferred network type is set to this
Wnderful setting.. amazing speed... performance of handset increased like rocket..
Thanks a lot...
Hi,
After dialing *#*#4636#*#*, it shows up the menu.
But i am not able to select Phone Information option. It says "This application does not work on this device".
Phone info: LG G2 D802 - Rooted - PowerG2 2.1 ROM.
I face frequent network signal drop, I tried CloudyG2 ROM also.
Thanks !

4g / LTE Toggle / radio control

At work the 4g LTE signal for ATT is very poor in the building, but we have 4g repeaters for ATT to fix this issue. Unfortunately, phones are stubborn and like to stay on 4g LTE despite having 1 bar of signal vs full signal with 4g. I had this same issue on my iphone 5 but was able to easily force off LTE while i was at work and have a steady, reliable data connection. My Note 4 seems to have the same affinity to wanting to be on 1 bar of LTE, but I cannot figure out a way to toggle / force LTE off and just use 4g. Anyone have any ideas? Anyone know of an application I can use to resolve this issue?
Thanks
try settings...more networks...mobile networks....network mode....It should be in there..I have the sprint model so I don't know for sure...but that is where mine is....hope this helps
djboo4you said:
try settings...more networks...mobile networks....network mode....It should be in there..I have the sprint model so I don't know for sure...but that is where mine is....hope this helps
Click to expand...
Click to collapse
Unfortunately, there is no option for Network mode on the ATT version. I wonder if this has to do with voLTE....
I did find a backway to the network mode via *#*#4636#*#* but I am unsure of what I should be setting to "disable" lte while I'm in the building at work.
I think I've sorted this out now. If I change LTE/GSM AUTO to WCDMA preferred it seems to immediately switch and hold onto 4G. I do have to change it back. Maybe I will write something so I can quick toggle this since nothing on the app store seems to work.
hi,
If you are rooted ? You can use an xpose module called Intelli3G
I use it on my phone ,works 100% and switches smoothly/fast between eg 4G..3G automatic
eg if my data is of its on 3G as soon as i switch data on /wifi it changes to 4 G
For interest sake ,here is a link to market ,you can read desciption what it does ?
https://play.google.com/store/apps/details?id=com.voidvapps.intelli3g&hl=en
good luck

Categories

Resources