Im trying to have my HTC LEO run an Andriod ROM. I meet all required spec. I got the necessary files on my PC ready to roll. Here 's the problem The WMDC will load phone and information and show that it's connection is on. I go to run MAGLDR1.11 and it works but when it gets ready to start updating the progress stays at 0%,the WMDC disconnects and the MAgrdl 1.11 ask me do a recovery.
( plz note that the tri color screen does come up but that's when my phone is disconnected.the HTC progress bar stays at zero, until i take battery out.
Please can someone help with this cause, I have tried everything...I mean everything..
Active Sync on, Faster connection box...off....Soft reset...hard reset....power off everything... reinstall everything....
Clove2479 said:
Im trying to have my HTC LEO run an Andriod ROM. I meet all required spec. I got the necessary files on my PC ready to roll. Here 's the problem The WMDC will load phone and information and show that it's connection is on. I go to run MAGLDR1.11 and it works but when it gets ready to start updating the progress stays at 0%,the WMDC disconnects and the MAgrdl 1.11 ask me do a recovery.
( plz note that the tri color screen does come up but that's when my phone is disconnected.the HTC progress bar stays at zero, until i take battery out.
Please can someone help with this cause, I have tried everything...I mean everything..
Active Sync on, Faster connection box...off....Soft reset...hard reset....power off everything... reinstall everything....
Click to expand...
Click to collapse
It's normal to lose ActiveSync / WMDC connection when you flash and it is not needed. Read the Noob guide for Flashing NAND roms (link in my signature). You are getting stuck at 0% because you don't have HSPL 2.08.hspl loaded. You've tried everything except reading the instructions
OK can you give some steps in order to set this up dont see link that your talking. Man you would be my hero if that was it.
I got thank you so much CLyde B1. Thanks again. That was easy...and you right I need to read carfully. Just one step cause all that. God Bless Ya Man>>>
Related
I used USPL for unlocking the cid of my P3350(LOVE)... As it mentioned in the USPL manual it works perfectly till step 12 (that is my phone screen becomes dark).
Here is the problem starts.. When the phone screen becomes dark, my device is automatically disconnected from my PC..Is this normal?
Since this is the 1st time flashing a mobile i was excited, but due to this problem I am very much frustrated.. Plz help me...
Yest it's normal. You will lose the Activesync connection.
Then you have to run the Run update utility that will show next, to uptade your SPL.
Cheers
Zecanilis said:
Yest it's normal. You will lose the Activesync connection.
Then you have to run the Run update utility that will show next, to uptade your SPL.
Cheers
Click to expand...
Click to collapse
thanks for replying Zecanilis, but after that if i run the update utility, i am getting error 260.
PLZ Help me...
this problem happened wid me aswell...i just flashed a ROM couple of hrs back...1stly use XP for flashing ur ROM and yes it is normal tht ur USB connection will be lost, wait for a few secs (10-20) and when the ROM Update Utility starts go ahead wid the wizard and it will flash the ROM
OK....I've followed all the tutorials, searched, and still I can't figure out how to get Hard HSPL2 on my tmous HD2 so that I can then begin the process of installing custom ROMs. When I run the HSPL2 from the zip, I follow the on-screen instructions, select 2.08hspl, and select next. After that my phone does the tri-colour thing and then it just sits there with a green bar moving back and fourth on the screen. It doesn't give me a percentage amount to let me know how far along I am!
I let it sit for 30 mins....and still nothing. And also....activesync disconnects once HSPL2 is ran. If anyone knows whats going on please help me. I really need a custom ROM. Thanks in advance.
EDIT: Just so you guys know....I am running Windows XP SP3, I have Activesync 4.5 installed, HSPL will load and got thru the process, but nothing after that. The green bar will just go back and fourth for a long time.
I'm a noobie to WinMo. I don't know if my advice will help, but I'll share. I had a similar problem when I tried installing HSPL2. For some reason, when my HD2 was in bootloader mode, it would disconnect from the USB connection and reconnect. But HSPL wouldn't finish the installation and I kept getting a fatal error message that connection was lost. All I did was was run HSPL2 again after I got the error message and it worked fine. If you're getting the same error message, it should work.
I'm not getting the error msg, It's just that the HSPL installer is stuck on the installation screen and just sits there. The green bar will go back and fourth for like 20-30 mins. IDK what I can do to fix it.
i'd say try every usb port,especially try to use one round the back.and don't forget to run as administrator,
I've downloaded the HSPL_1024. What happens is I'll run it, it'll go thru the process, but in won't install. There's a green bar that goes back and fourth forever. My phone will sit on the tri-colour screen and nothing else will happen. I let it sit that way for a long time and still nothing. Shold I do a hard reset or what?
Watch This!
http://www.youtube.com/watch?v=a6Bt0S7dCmM
It's funny, I just watched that video. Followed exactly what that guy did. His finished in under 2 minutes or so. After about 15 minutes...mines still has the green bar going back and fourth. I am getting so frustrated. I love this phone but I can't stand having to deal with things like this in order to get to it's full potential.
its a long shot but try taking out the sd and sim, and i repeat what i said about usb ports. hspl is far more picky about it than regular flashing.
try starting already in bootloader, if the word serial doesn't change to usb then there is your problem.
Im getting an error msg now. ughhh! And the error msg comes after letting the program run for about 10 mins. I'm going to try and take the sim and SD card out and then try again. IDK what I'll do after that.
samsamuel...I've tried everything you said. Now I'm getting a "Critical Error". I'm on a Macbook running Windows XP SP3 in VMWARE. I have activesync 4.5 (not WMDC) Does this make a difference at all? If none of this helps I'll just have to do a hard reset and try it again.
tylawtheboss said:
samsamuel...I've tried everything you said. Now I'm getting a "Critical Error". I'm on a Macbook running Windows XP SP3 in VMWARE. I have activesync 4.5 (not WMDC) Does this make a difference at all? If none of this helps I'll just have to do a hard reset and try it again.
Click to expand...
Click to collapse
ohhhh well there you are then. when the phone is running propperly, the mac can happily pass the usb signal through, but when it boots to bootloader, the mac fails to propperly pass through the signal. (Based on stuff that i have read , , i dont have a mac)
Got a friend with a PC? use that to flash HSPL, and then on your own machine give bootcamp a try to actually run xp rather than vmware for flashing.
tylawtheboss said:
samsamuel...I've tried everything you said. Now I'm getting a "Critical Error". I'm on a Macbook running Windows XP SP3 in VMWARE. I have activesync 4.5 (not WMDC) Does this make a difference at all? If none of this helps I'll just have to do a hard reset and try it again.
Click to expand...
Click to collapse
Use a PC...that'll work
just loaded Windows 7 on my laptop and went to flash to the latest energy rom. Im not familiar with WMDC but when it goes to flash, it gives me the RGB screen when rebooting my tp2 then my pc reports cannot complete update due to lost connection... wtf... why? win7 not compatible? am I a retard?
Not at all
XITruthiX said:
just loaded Windows 7 on my laptop and went to flash to the latest energy rom. Im not familiar with WMDC but when it goes to flash, it gives me the RGB screen when rebooting my tp2 then my pc reports cannot complete update due to lost connection... wtf... why? win7 not compatible? am I a retard?
Click to expand...
Click to collapse
I have Windows 7 and flash my ROM. It's not a Windows 7 issue more than likely. It sounds like you have not connected with Activesync before you tried to flash your ROM. The reason I say, you haven't established a communication port with your pc and it therefore cannot enter a usb connection in bootloader. I have had this happen when I didn't wait for activesync to sync with my computer. I got an ERROR: screen, so I know what you're talking about.
Just sync your device with Mobile Device Center and as soon as activesync completes, run the ROM install.
Let me know if this doesn't work. We'll proceed from there.
XITruthiX said:
just loaded Windows 7 on my laptop and went to flash to the latest energy rom. Im not familiar with WMDC but when it goes to flash, it gives me the RGB screen when rebooting my tp2 then my pc reports cannot complete update due to lost connection... wtf... why? win7 not compatible? am I a retard?
Click to expand...
Click to collapse
Its compatible but it can be rly retarded if you dont do it like it wants
1st install wmdc and let it connect to you phone
2nd disable usb connections on wmdc
3rd and so forth go onto flash your device
if it still says that then connect to the internent and boot your phone into the tri color screen WHILE still connected to computer and try flashing from there
I have flashed roms and done Task29 several/many times from my W7-32-bit laptop and my W7-64-bit desktop, and both work fine -- no issues. I didn't do any special procedures or settings (none on purpose, anyway)...it just worked.
I know this doesn't solve your problem...but it might help to know that W7 should work.
I guess by now this should be solved. If not, try getting into bootloader mode (turn your phone off, and turn on by holding power+volume up button). Then connect the USB cable and try flashing.
I also use Windows 7 64b, sometimes when flashing roms got the same problem, and had to reset the phone from the color screen using the button. This has never happed after I started using Task29, because I have to get into bootloader mode manually.
Ok... Id like to continue this post for only one reason, I am in fact a retard...
Simply reading the stickys is always crucial in your quest to not appear far more retarded than you actually are. Apparently windows 7 update DOESNT update WMDC to 6.1. I Re-Read the "For Noobs" sticky and realized hm, maybe I should check to update WMDC and WHAM, no problem.
The moral of the story, read the previous posts. Asking questions in text based form on the forum when perfectly good answers already float about right in front of your eyes is just a complete waste of precious bandwidth, so dont do it.
I apologize.
Sometimes I post things and feel like a complete idiot, I actually just had a lot of trouble flashing my tp2 to a cooked rom for the first time, but I've had HTC phones since the wing and still run into problems. This last bout of problems I had was fixed by simply reseting my phone to factory default :O
Hi everyone i was wondering if anyone could help me... i have several questions about my htc touch elf see i just upgraded it to the onyx 4.something version and after 4 days the wifi stoped working it wont turn on and it wont detect my sd card either... i was wondering if anyone could help me on how to degrade it to a better ROM or anything cause when i try to degrade the onyx 4.something to 3.0 it says it cant establish a conection between the phone and the computer when i run the romupgradeutlity and when i hit the upgradeimage buttom... ... please help me.. thanks a lot!
post in Onyx ROM thread and read the stickies.
Your Elf Device, Our Vogue Device
Sorry, your device is simply different internally.
http://forum.xda-developers.com/showthread.php?t=713265
rasv19 said:
Hello I was wondering if anyone could help me... i have an htc touch elf and i upgraded it to the Onyx 4.0 after 4 days of use it started giving me some trouble sometimes i hitted the touch screen and it opened something else , my wifi stoped working it wont turn on and it wont detect my micro SD... i tried downgrading to Onyx 3.0 through ROMupdateutility but when it was at 0% it said it coudlnt detect the mobile device... i was wondering if anyone could help me fix this problem cause i want my phones wifi to work and micro sd too. thanks a lot.
Click to expand...
Click to collapse
please try a hard reset, that should help solve the problems.
i doubt if this is anything to do with ROM you flashed (since you have flashed successfully, as your phone does boot.
if none of this works please post.
a hard reset should help you though.
rasv19 said:
nope it didnt worked my phones wifi still not working and its not detecting my sd card.... like wheneve ri turn blutooth on the wifi green light turns on with it but the wifi wont turn on itself and then when i go to the music thing on my phone it detects the first song i have but when i play it says theres no files and the sd card wont show up on the file explorer.... and other thing when i try upgrading or downgrading my phone by romupgrade utility i get the error 222 canot eswtablish conections between your pda and computer check usb cable.... so i dont know cause the first time i upgraded it from the manufacture ROM to the onyx 4.somethhing it went pretty great..
Click to expand...
Click to collapse
i see, error222.
please make sure that your USB cable is working.
pleasemake sure your computer has active sync 4.5 installed ( if windows XP)
or the latest WMDC (if vista or win7 )
also regarding the memory card, are u sure the card is fine ?
please put it another device/card reader and check, try formatting it and see if ur elf detects it.
ROMs usually don't have anything to do with memory drivers.
what HSPL/USPL did u flash ?
Prowess said:
Sorry, your device is simply different internally.
http://forum.xda-developers.com/showthread.php?t=713265
Click to expand...
Click to collapse
You posted in the Vogue section. I have transferred your thread to the Elf section.
yeah it works on other devices.... the usb cable is working really fine and i dont know what uspl i flashed .. . like i mean everything went rite until 4 days after i instaled the onyx 4.0 ultimate everything was working fine with it but 4 days later it started to give me that problem ... and i try to change ROM but i cant it wont let me i run active sync andeveyrthing it says its conected i run the romupdateutiliy then the status bar opens up but it stays at 0% and then the error 222 shows up... but my phone goes to the bootloader but it wont pass from there.. and when i close the romupdateutility my phone switches to the status bar but stays in 0% and then my phone crashes and i have to unbrick it.
first of all please do not open 3 different threads for the same problem, i have removed the other two.
also as aman said try posting in the the rom thread.
please read thee thread which have been stickied on the ROM development thread.
please be patient
thanks for your co-orperation.
Gone through the various help threads on rebooting, resetting etc.. Battery is charged, m/card and sim have been removed..
Phone is at the boot loader stage - reads Upgrade ROM code error - have the USB plugged in and can see the USB writing on the white part of the red,green,blue,white screen but pc refuses to make a connection.. keeps saying activsync not connected or busy..
Have tried rebooting the phone and also the pc, changed cables, changed USB port.. no joy..
Any suggestions appreciated..
not sure what you want...but you have certainly described the situation really well.
i understand that your device is in the bootloader (thats the multi-color screen). i understand that "USB" is written at the bottom of the bootloader screen. i understand that you have removed all the cards.
what i don't understand is what you want help with? why are you trying to establish an activesync connection? activesync will obviously NOT connect if you are in the bootloader because the bootloader isn't the same as windows. windows mobile must be running if you want a full activesync connection.
so what exactly are you looking for? do you want to flash a ROM or radio ROM or some such? are you simply trying to "hard reset" your device? details please!
yea, dont be confused by posts that say 'when connected to active sync, blahblahblah', they dont really mean activesync the program, they simply mean a usb connection. The fact that it says USB on the white part means you can now run your rom flash,.
ok.. what I am trying to do is re-flash the ROM.. I had a flashed ROM on there and I was just going to upgrade it to the latest one (Laurentius26 GoldEdition V3.4 Stock/Spike™ WWE 23568) and about 20% of the way through it froze and then I get a recovery screen come up.. followed the instructions and started to flash again and the same thing happened.
In both cases it seems as if the USB connection was dropped even though there was nothing else happing on the pc at the time.. now when I try to re-flash, no US connection is being established.
Well I left everything disconnected last night and tried again this morning. We have got a connection now but the re-flash has failed again so I shall just go back to the old ROM.. thanks for you all's input.
probably a bad ROM download. I would try to download again and if that doesn't fix it, let the ROM cooker know that he probably has a bad upload of the ROM.