when i enter the recovery mode
i got into Android system recovery (2e)
then i choose apply sdcard:update.zip
then it forward me to ClockworkMod Recovery v2.5..
then i choose apply sdcard:update.zip again..
then it rebooted and back to system recovery (2e) again
what should i do to fix this ? i want to update my ROM
If your custom ROM can be flashed via cwm, go save it in your internal sd then use the install zip in sd card option in cwm.
I suggest you do a full nandroid back-up first just to be on the safe side...
thanks for reply..
i think i can't use cwm anymore to flash.. since it keeps looping between this two recovery mode.. i just flash it using odin, now i'm runnning original firmware 2.1
but i still see those two recovery mode.. how to remove one of them ?
When you get into Clockwork, don't press the "apply update.zip".
Select "install zip from sdcard" and locate your roms .zip and install it.
Read the instructions again and again until you understand it. It's obvious that you have no idea what you are doing.
Sent from my GT-I9000 using XDA App
If I understand your post correctly, you are having trouble getting into CWM after installing it. I had the same thing on my phone.
When going into recovery, you hold down the power button, the home button and the volume up button and release the home button when the Samsung screen appears. I tried releasing the power button when the Samsung screen appears and it goes into CWM recovery.
Ian
Im trying to backup my current rom using rom manager. I flashed clockwork and all that, when i goto back up rom it resets and shows me the phone with the (!) sign above it. then i have to restart. any help on getting it to actually backup my rom?
The ! screen you are getting is the stock recovery. Go into ROM manager (you are rooted I hope?) and choose to install Clockwork Recovery (do it two or three times, it takes a few tries to "stick"). Then choose to "backup" and it will reboot you into Clockwork Recovery which will have backup options (and more!) available for you.
How exactly do you install a new rom, such as this one, NFX-Shift STOCK 1.17.651.1 PNG optimized/zipaligned deodexed? I followed the steps to set-up recovery and created a nandroid back-up, but how can I check to see if it worked. Just still a bit nervous about crashing or ruining my shift.
Boot into recovery by turning your phone off, then powering back on while holding the vol down button.
When you see the bootloader select Recovery.
Choose factory reset/data wipe.
When it finishes select install zip from SD and navigate to the ROM you wish to install (DO NOT select install update.zip)
When it finishes doing its thing choose Reboot to system.
If there are any problems boot back to recovery and restore your backup.
this is how to install a new rom correct? Thanks
yep, have fun
You need to read more and gain more confidence in what your doing
Sent from my PG06100 using XDA App
Ok guys..... newbie here .... literally I'm new to Boot unlocking, root, Flashing etc.
Anyway I have followed this forum for so long that I decided to take plunge yesterday and get my hands dirty.
Here is what I did:
Unlock bootloader, root and install recovery on my Atrix 4G. Atrix was @ 2.3.4 and 4.5.91 during unlocking & root.
Rebooted the phone and everything seems to be in place. Atrix loaded like the way I bought it 7 months back. No problem until now.
Also created a restore folder on my external SD. Worked fine and was successful in creating backup with time stamp
Now here are my steps and subsequent issues that I'm facing:
1. Downloaded CM9 zip file from this thread(http://forum.xda-developers.com/showthread.php?t=1500535) along with Gapps to my external SD
2.Entered recovery mode during bootup and tried to flash CM9 and Gapps. Flashing seem to have gone well and completed (note I did not do clear data, clear cache or clear dalvik cache under advanced options being a newbie)
3. Reboot the phone and can only see red Moto logo and unlocked on top. Left for about 5 minutes and nothing happened.
4.Did a battery pull and entered recovery mode. wiped data, cache & cleared dalvik cache
5.Went to Install zip from sdcard option and tried to reflash CM9. Flashing seems to have gone well and completed
6. Reboot phone and again can only see Moto Red logo with unlock on top and nothing more.
7.Battery pull followed by recovery. But This time I tried to restore from my external SD. also wiped data, cache & dalvik cache
8.Restore took about 3 minutes and completed.
9.Reboot the phone. Now the phone boots and goes to Rethink possible screen and get sstuck.
10. Left it for 1 hr....nothing.
11.tried steps 7-9 again and still stuck in "Rethink possible" screen during boot.
What did I do wrong? Did I soft brick the phone? I can still enter recovery mode and read my internal and external SD and can see all files. i hope I didn't brick my phone doing this. If I did, I would regret!
Here are my options:
1.Try a stable ROM like CM7 and see what happens. I didn't want to do too much damage so haven't tried this option yet.
2.I know there is a way to hide 'unlock' during boot up (if someone can point to it obviously). Hide the 'unlock' and return the phone to ATT and tell them that phone would not boot after 2.3.6 update and get a refurbished one
Please let me know what your thoughts are. I'm currently crapping on my pants
Edit: I just tried Newtrino rom and stuck @ Moto screen which says unlock.
Edit 3/4/2012: Please go to the last post for the solution. Tenfar's CWM is old and cannot deal with latest ROMs. Use ROMRACERS latest CWM or touch based Koush's CWM for future ROM flashing.
Old CWMs will give you sleepless nights!
Ok tried restore again after wiping data, cache & dalvik cache.
Now after reboot, My Moto Logo screen says unlock and just starts flashing.
I can still get into recovery......
can someone please help me......
What you can do is: install a "stable" ROM of Gingerbread:
--Go in recovery, put a .zip of the ROM on your sdcard (with your computer), and after wiping data, install it .zip.
--Or you install a new ROM with fastboot
Anyway, be careful with your battery, because if it is empty, with no ROM on your phone, it'll be crap!
vsg005 said:
What you can do is: install a "stable" ROM of Gingerbread:
--Go in recovery, put a .zip of the ROM on your sdcard (with your computer), and after wiping data, install it .zip.
--Or you install a new ROM with fastboot
Anyway, be careful with your battery, because if it is empty, with no ROM on your phone, it'll be crap!
Click to expand...
Click to collapse
thank you for your response. However I tried that already Nutrino GB ROM. Again, I would go to 'M' screen which says unlocked and its stuck there for ever.
I used tenfar's CWM. Not sure if I need to use any other CWM. Also since my phone doesn't boot, I'm not sure how I can install any other CWM
Masterguy said:
thank you for your response. However I tried that already Nutrino GB ROM. Again, I would go to 'M' screen which says unlocked and its stuck there for ever.
I used tenfar's CWM. Not sure if I need to use any other CWM. Also since my phone doesn't boot, I'm not sure how I can install any other CWM
Click to expand...
Click to collapse
Don't worry, soft bricks are easy to recover on the Atrix thanks to us being able to access fastboot.
For flashing a new recovery:
While your phone is off, press Volume Up + Power to power up, then release when a menu appears on your screen and navigate with volume down until you see Fastboot, select it with the volume up key.
Get the necessary files for fastboot, place them all in a folder called "moto" in your C: drive, and type in the following in a cmd window (assuming you're using windows and that the recovery image is called recovery.img):
C:/Moto> fastboot flash recovery recovery.img
C:/Moto> fastboot -w
C:/Moto> fastboot reboot
Now access your recovery wipe dalvik cache, cache, factory reset and then flash a new ROM. It SHOULD boot without issues. I personally use Koush's Clockworkmod Touch, also remember that Neutrino tends to get "stuck" sometimes after the first attempt to boot and requires a battery pull and then you try to boot again. (It takes a while)
littleemp said:
Don't worry, soft bricks are easy to recover on the Atrix thanks to us being able to access fastboot.
For flashing a new recovery:
While your phone is off, press Volume Up + Power to power up, then release when a menu appears on your screen and navigate with volume down until you see Fastboot, select it with the volume up key.
Get the necessary files for fastboot, place them all in a folder called "moto" in your C: drive, and type in the following in a cmd window (assuming you're using windows and that the recovery image is called recovery.img):
C:/Moto> fastboot flash recovery recovery.img
C:/Moto> fastboot -w
C:/Moto> fastboot reboot
Now access your recovery wipe dalvik cache, cache, factory reset and then flash a new ROM. It SHOULD boot without issues. I personally use Koush's Clockworkmod Touch, also remember that Neutrino tends to get "stuck" sometimes after the first attempt to boot and requires a battery pull and then you try to boot again. (It takes a while)
Click to expand...
Click to collapse
Many people also seem to have suggested RACEROM CWM. Which one would you suggest? I'm so nervous about all this now. Just have this butterfly in my stomach
flash the latest recovery and wipe everything in recovery and flash neutrino again. It should work after that. try neutrino 2.2 though. 2.5 still has it's kinks.
1st off, relax. It's difficult to brick your phone from this point Just don't get any bright ideas with .sbfs lol.
As others have said, make sure you're on latest recovery.
Question: are you installing from internal or external SD? Internal is recommended for flashing most ROMs.
Sent from my MB860 using xda premium
Masterguy said:
Many people also seem to have suggested RACEROM CWM. Which one would you suggest? I'm so nervous about all this now. Just have this butterfly in my stomach
Click to expand...
Click to collapse
As someone else said, the ONLY thing you should NEVER do is flash an .sbf or go through an OTA update, that's a surefire way to hard brick your phone. From this point on it's VERY DIFFICULT to completely brick your phone using software only.
RomRacer's CWM is based I think on v5.0.2.7? Koush's latest recovery is v5.8.1.5. I honestly couldn't name any tangible differences other than the touch interface, which is the reason I use it in the first place. (I hate mashing volume keys like a madman) It really doesn't matter which CWM you use, but when I soft bricked my phone I recovered with CWM Touch.
I would recharge your battery to 100% before trying to recover it, as that is one less headache to worry about, but if your phone starts saying 'Battery is too low to flash', do not panic, you only need a USB cable you don't mind sacrificing (doesn't have to be new). I will go into detail in case you actually need to do this.
Just make sure you use the fastboot -w command and wipe EVERYTHING through CWM before trying to flash anything else.
Solved:boot loop issue
littleemp said:
As someone else said, the ONLY thing you should NEVER do is flash an .sbf or go through an OTA update, that's a surefire way to hard brick your phone. From this point on it's VERY DIFFICULT to completely brick your phone using software only.
RomRacer's CWM is based I think on v5.0.2.7? Koush's latest recovery is v5.8.1.5. I honestly couldn't name any tangible differences other than the touch interface, which is the reason I use it in the first place. (I hate mashing volume keys like a madman) It really doesn't matter which CWM you use, but when I soft bricked my phone I recovered with CWM Touch.
I would recharge your battery to 100% before trying to recover it, as that is one less headache to worry about, but if your phone starts saying 'Battery is too low to flash', do not panic, you only need a USB cable you don't mind sacrificing (doesn't have to be new). I will go into detail in case you actually need to do this.
Just make sure you use the fastboot -w command and wipe EVERYTHING through CWM before trying to flash anything else.
Click to expand...
Click to collapse
Thanks I was able to fix my boot up issue using ROMRACERS CWM. I didn't use any command prompt or anything. I just downloaded zip file from this thread, entered recovery mode -->Install Zip from SD card --> Chose ROMRACERS zip --> it automatically flashed the recovery and I then rebooted recovery under advanced options.
After that Wiped data,cache & Dalvik Cache and proceeded to install CM9 and it booted up up flawlessly.
I'm kind of surprised that tenfar didn't add a not to use his CWM as the latest ROMs use latest ext format.
That seems to be issue. However, I'm pleased with your guidance and final output. Thanks a lot dude.
Masterguy said:
Thanks I was able to fix my boot up issue using ROMRACERS CWM. I didn't use any command prompt or anything. I just downloaded zip file from this thread, entered recovery mode -->Install Zip from SD card --> Chose ROMRACERS zip --> it automatically flashed the recovery and I then rebooted recovery under advanced options.
After that Wiped data,cache & Dalvik Cache and proceeded to install CM9 and it booted up up flawlessly.
I'm kind of surprised that tenfar didn't add a not to use his CWM as the latest ROMs use latest ext format.
That seems to be issue. However, I'm pleased with your guidance and final output. Thanks a lot dude.
Click to expand...
Click to collapse
Thank you sooo much. I was having this exact problem. I did what you suggested and my phone works. Thanks!
Hi there guys!
I have rooted and unlocked the bootloader for my Nexus 10, and just wondering how do i go about installing & booting multiple roms? Do i need some special software?
Thanks!
chronosoft said:
Hi there guys!
I have rooted and unlocked the bootloader for my Nexus 10, and just wondering how do i go about installing & booting multiple roms? Do i need some special software?
Thanks!
Click to expand...
Click to collapse
I always find zedomax's videos to be extremely helpful for visuals. He also shows how to load custom roms.
http://forum.xda-developers.com/showthread.php?t=1997227
You'll need to download a recovery program like Clockwork Recovery or TWRP. Both have official websites with the latest release of their recovery programs. Just Google them.
DizoAZ said:
I always find zedomax's videos to be extremely helpful for visuals. He also shows how to load custom roms.
http://forum.xda-developers.com/showthread.php?t=1997227
You'll need to download a recovery program like Clockwork Recovery or TWRP. Both have official websites with the latest release of their recovery programs. Just Google them.
Click to expand...
Click to collapse
Thanks for the reply, I have TWRP installed, so do i just flash the downloaded rom as per normal and use TWRP? Is there an option in TWRP?
Thanks!
chronosoft said:
Thanks for the reply, I have TWRP installed, so do i just flash the downloaded rom as per normal and use TWRP? Is there an option in TWRP?
Thanks!
Click to expand...
Click to collapse
Yeah, so for example. Download CleanROM which is pretty much a stock ROM and all functions of the tablet seem to work that I've tried so far, GPS, WiFi, Camera. Haven't tried HDMI or Audio port yet. Microphone works too.
http://forum.xda-developers.com/showthread.php?t=2113048
Once you download the .zip file for CleanROM to your tablet, it will be in the Downloads directory under the directory /sdcard/0/Dowload.
Then reboot in to fastboot by holding down the volume +/- at the same time along with the power button held. Once you get to the fastboot screen, use the volume rocker until you see Recovery Mode, then hit the power button. This should put you in to TWRP which you said you have loaded as the recovery program. I have Clockwork, it's just a different recovery program, but I've used both before fine. Watch this for TWRP and how to make backups. http://youtu.be/EDZ1WAwXvbE?t=1m30s
Normally, I do a complete clean install each time, but I've also been successful loading from one rom to another and not performing the factory reset. As long as you don't perform the factory reset your apps and settings should remain.
However, I'm a person who likes to do a clean install, so I usually wipe all cache options first, then perform a wipe/data/factory reset and load the rom I want. From there, there should be an option to install from a .zip file, that is where you would go to load the custom rom, then select it and let it do its thing. After installing the ROM, I repeat the steps of wiping cache and factory reset after the ROM install is complete, before I reboot the tablet. Once I do all that, I reboot the tablet and let it load.
People say you should perform a backup of your existing ROM/Settings by using the recovery program to do so, that's really up to you if you want to do it, but it does provide a method to restore your prior rom/settings. I don't, because I just got the tablet and don't have a lot of settings/programs installed at the moment.
If for some reason your tablet just gets stuck at the Nexus X when loading, you may need to perform the wipe data/factory reset from Recovery. If you need to do it from the PC, you can load in to Fastboot (power and volume +/-) let it sit there with your USB cord connected and from your PC go to the directory with fastboot.exe and run "fastboot -w" to wipe. You will lose all your settings and programs just like when doing the wipe through recovery.
Hope this helps. Note, some ROM's suggest loading GApps, I haven't messed with those ROMs yet, but imagine it just requires installing a 2nd .zip file after installing the rom .zip file with recovery.
ah that's how it's done. Thanks for clarifying this DizoA, that's really helpful, appreciate it!