[Q] Cant boot android. - HD2 Android Q&A, Help & Troubleshooting and Genera

hi there, my hd2 has spl 3.03, radio 2.15 and ROM 3.14. from doing a bit of research on the forums I've found that i can run Android roms without needing to flash. however after trying a few different roms they all seem to freeze on the white htc screen even after leaving them go boot for around 30 mins. can anybody please help me with this issue?
appreciate any help given.

Bump.
Does anybody please have any ideas? I bought the HD2 because I thought I could run android on it...

I've tried multiple ROM and android build combinations and the only one I can get to boot up is from the minimum "energy" package. I've formatted the SD card in each case, and still no luck. I;m new at this whole process so I'm sure I'm screwing something up

Hello!! Me too, i have the same problems : Artemis v44, Rom 3.14, radio 2.15.50.14. and i have 8gb sd card. I tryed different android rom, but it's the same problems.
I continue to try....
Sorry for my bad english.

read the other threads with the same topic on the 1st couple pages...
basicly the proven way to fix it is to format the sdcard to get rid of ghosts that are left over from old data.

Does that mean a full format or Quick format? Ive try quick multiple times. And what first couple of pages are you refering/ Thanks for the response!

full format actualy wipes it, all quick does is removes file names.

you da man! Im doing a 16g......its taking a long time.....is that normal?

Well.....that didnt work. Full format on a 16g SD. Still locks up on HTC screen. Any ideas. Gonna try new SD card tomorrow.

I have the same result, use a new 8g card, android build MCCM_SE_V3.3_FroyoStone_Sense. On my first boot OK. I need to change battery and sim often. switch off and next boot stay on HTC screen forever... Found some solution saying that you must run the two "exe" within 15 sec. after boot into WM, but still doesn't work... help help

Same problem here.
Tried all the steps.
Installed HSPL2
Upgraded radio to: 2.12.50.02
Fully formatted my sd card
Tried several builds (FRG83.MCCM_IR_1.7 & desire hd2)
But it keeps on freezin at the HTC screen when booting.
Any help would be very much appreciated since I'm very much out of guesses.

have you tried deleting cmd line?

Same Problem...
Rom 3.14.407.2
SPL 3.03
Radio: 2.15.50.14
pls help

jose makalolot said:
have you tried deleting cmd line?
Click to expand...
Click to collapse
Nope, I haven't. Could you explain or link me some explanation?
Gr
TJ

teejee said:
Nope, I haven't. Could you explain or link me some explanation?
Gr
TJ
Click to expand...
Click to collapse
open startup.txt and delete the whole line with "set cmd..." then try to boot android again.

jose makalolot said:
open startup.txt and delete the whole line with "set cmd..." then try to boot android again.
Click to expand...
Click to collapse
This got me further yet it didnt work fully. It got me passed the HTC logo and unto the Android logo but then it crashes and fully restarts.... into windows.
So this might be a different problem... any thoughts?

teejee said:
This got me further yet it didnt work fully. It got me passed the HTC logo and unto the Android logo but then it crashes and fully restarts.... into windows.
So this might be a different problem... any thoughts?
Click to expand...
Click to collapse
I can give you a copy of my modded system.ext2 based on mdj 1.7, maybe it will work for you. Maybe we can do it through IM. Just PM me.
By the way, what is your location and carrier? I cant see info, am using phone.
Sent from my HD2 using XDA App

Ive formatted multiple times and have ran different Android ROMs. NOTHING. Only thing that works is the basic one provided by ENERGY. (Thanks by the way). Not that this is a bad ROM, Im just trying to learn about this stuff and its frustrating. I'm sure there is more guidance within the threads, but thats like pretty difficult if you dont know where to look

adb logcat
post it, then we can troubleshoot.
dont know how to do that? search. theres atleast 10 stickies in the forums on adb for dummies.
also, i get kinda tired of folks begging for help that cant even do simple stuff like fill out location, sig line etc... come on throw us a bone.

Related

Booting Problem on my HTC HD2

I have all the file for botting Android Froyo 2.2 on my phone and I have followed all the steps for flasing and installing a new ROM but now when I go to boot Froyo it just stays in Boot Mode and I know the first boot takes a while but my phone has been in boot mode all day.... Can someone pplease give me a solution to fixing this problem.... Thanks
Jamal0910 said:
I have all the file for botting Android Froyo 2.2 on my phone and I have followed all the steps for flasing and installing a new ROM but now when I go to boot Froyo it just stays in Boot Mode and I know the first boot takes a while but my phone has been in boot mode all day.... Can someone pplease give me a solution to fixing this problem.... Thanks
Click to expand...
Click to collapse
I know you said that you did all the steps, but did you format the SD card? As well, did you create an "Android" folder or did you just copy over the build to the root of your card?
What are your stats, for better help.
And, lastly, did you search your builds thread for problems?
I too am having this exact same problem.
Actually I had android working fine on my phone for about a month.
When I tried to load another ROM, I could not get it to load anymore.
I followed all the steps, I also reformatted my card and copied the file over to the root of my card.
Now when I try to load the original Android ROM that I had going on my phone that will not will load either. When I click the HaRet.exe it goes to the hTC screen and just freezes there and does not progress, I have waited over an hour and no changes occur.
I have the VBNROM with Radio 2.15.50.14
I have tried 5 or 6 different Android ROM's and all give the exact same result.
I searched the build threads for some of these but could not find anyone with a similar problem.
When it was working, I had ChuckyROM with Radio 2.12.xx.xx
And I tried with this also, and now am having a similar problem
If anyone has a solution to this, it would be greatly appreciated.
goatboy6 said:
I too am having this exact same problem.
Actually I had android working fine on my phone for about a month.
When I tried to load another ROM, I could not get it to load anymore.
I followed all the steps, I also reformatted my card and copied the file over to the root of my card.
Now when I try to load the original Android ROM that I had going on my phone that will not will load either. When I click the HaRet.exe it goes to the hTC screen and just freezes there and does not progress, I have waited over an hour and no changes occur.
I have the VBNROM with Radio 2.15.50.14
I have tried 5 or 6 different Android ROM's and all give the exact same result.
I searched the build threads for some of these but could not find anyone with a similar problem.
When it was working, I had ChuckyROM with Radio 2.12.xx.xx
And I tried with this also, and now am having a similar problem
If anyone has a solution to this, it would be greatly appreciated.
Click to expand...
Click to collapse
How are you installing the Build? Through USB or through directly inserting the card into pc?
deadmansink said:
How are you installing the Build? Through USB or through directly inserting the card into pc?
Click to expand...
Click to collapse
Directly inserting card into pc
Did you do a full format of your SD-card, or just a quick format? If these kind of issues occur, I'd advise you to do a full format, for example with SDFormatter. If the issue persists, do a task29, flash your ROM and Radio again and start over.
Sincerely,
Mac
Macelangelo77 said:
Did you do a full format of your SD-card, or just a quick format? If these kind of issues occur, I'd advise you to do a full format. If the issue persists, do a task29, flash your ROM and Radio again and start over.
Sincerely,
Mac
Click to expand...
Click to collapse
Excuse my ignorance, I'm kind of a noob at this...what is a task29?
goatboy6 said:
Excuse my ignorance, I'm kind of a noob at this...what is a task29?
Click to expand...
Click to collapse
Task29 means formatting the internal filesystem when you install a different WM ROM. It prevents leaving traces from a previous ROM when switching. What ROM and radio are you using?
Sincerely,
Mac
Sent from my reborn HD2 using Tapatalk Pro
I'm using the ChuckyRom with radio 2.12.50.02
goatboy6 said:
I'm using the ChuckyRom with radio 2.12.50.02
Click to expand...
Click to collapse
Then you should already be familiar with Task29 . Did you use it prior to flashing Chucky? If your troubles persist, I advise you to start over by reading this thread and then flash a compatible ROM and Radio of your choice. Make sure you re-format your SD-card as described in my previous post.
Let us know if you run into trouble...
Sincerely,
Mac

Can't get android to run

I'm trying to hookup my brothers HD2 with the JDMS 1.6.2 rom, but when I click either CLRCAD or HARET i get an error saying "The file HARET/CLRCAD cannot be opened. Either it is not signed with a trusted certificate or one of its components cannot be found"
he was running android fine, then he formatted his SD card to start fresh and now is getting these errors. anyone know how to fix this?
Have a look here...
http://www.yourmobileblog.com/2010/09/working-solution-for-errors-like-file-cannot-be-opened/
johncmolyneux said:
Have a look here...
http://www.yourmobileblog.com/2010/09/working-solution-for-errors-like-file-cannot-be-opened/
Click to expand...
Click to collapse
Sweet, thanks. Ill look at this more when I get home.
Sent from my SGH-T959 using XDA App
I had had the same problem twice. In both cases a hard reset solved the problem, though I'm happy to hear that there is another solution. I'll remember about it.
well the link provided didn't work for me.. I couldn't get it to install. I just downloaded the Stock T-Mo rom and flashed it.. Now i have a new problem..
after clicking the HARET.EXE, it says its booting linux then HTC pops on the screen, but then it reboots in Windows.. I've tried two different Android roms and I get the same problem on both.
Still having same problem...
I'm having problems trying to run the HD2ONE 0.3.5 rom. I can see the little penguin and the script running after I click the haret file, but the screen will go black and boot windows..
T-Mo US HD2
Stock Winmo Rom: 3.14.531.1
Radio: 2.15.50.14
I've this problem with three different roms now.
I can't help with your phone, as I obviously don't really pay much attention to the US T-Mo specifics, but this thread does...
http://forum.xda-developers.com/showthread.php?t=653614
Hope it helps
Five0nIt said:
Still having same problem...
I'm having problems trying to run the HD2ONE 0.3.5 rom. I can see the little penguin and the script running after I click the haret file, but the screen will go black and boot windows..
T-Mo US HD2
Stock Winmo Rom: 3.14.531.1
Radio: 2.15.50.14
I've this problem with three different roms now.
Click to expand...
Click to collapse
Just like "John..." said in post #7, try this link:
http://forum.xda-developers.com/showthread.php?t=878793
I would start over, format the micro SD card within WM, do a TASK29 and start fresh.

Is this called Bricked?

Just got a new phone, worked fine, put in my sim and sd, all was working perfect, then I went to music selection and it saw my songs on my sd card, i started playing one, the phone froze and just played the last note like its stuck on it, all buttons would not work.
I took off the battery put it back on now when i power up it just sits on the white and purple screen that says " stick together" the tmoblie logo, and wont move from there.
Removed battery a few times same thing, pressed the little hard boot button same thing.
Any advice?
thank you in advance.
The "little button" is the same as pulling the battery.....a soft reset.
You should try a hard reset, and failing that a fresh flash.
samsamuel said:
The "little button" is the same as pulling the battery.....a soft reset.
You should try a hard reset, and failing that a fresh flash.
Click to expand...
Click to collapse
Thank you,
Can you tell me how to do a hard reset? the steps
Also how do you fresh flash?
I did a search but the threads i found were hard to follow,
just need simple steps
http://www.youtube.com/watch?v=Wq64BzDLTvU:D
erikvario said:
http://www.youtube.com/watch?v=Wq64BzDLTvU:D
Click to expand...
Click to collapse
thank you, now when you do that, does it reset the phone to factory settings?
or keep those as I set them?
it will set the phone to factory settings.
Sounds like you're using stock. Stock never boded well with me either, so maybe you should try a custom rom. Search on the how to's, you'll learn something.
Kailkti said:
Sounds like you're using stock. Stock never boded well with me either, so maybe you should try a custom rom. Search on the how to's, you'll learn something.
Click to expand...
Click to collapse
Been using the stock ROM on my old phone for a while never had any one of the many problems that ppl have listed on this forum, but I cracked the screen and got a new one, and just ran into that problem.
Took the battery off and let it sit for a few, put it back in and now it loads and works, just odd, how that happen, haven't put my card back in yet but well test again hopefully it wont do it again.
don't mean to hijack but im facing the same problem
but mine is a world wide hd2. it freezes on the HTC screen
when i try flashing a rom from the bootloader (using RUU), it always gives me a image corrupted error message.
i also can't flash a new radio. error 00018003 occurs when trying to flash a new radio.
currently i have ENERGY rom loaded into it but won't start. stuck on the NRG loading screen
froibet said:
don't mean to hijack but im facing the same problem
but mine is a world wide hd2. it freezes on the HTC screen
when i try flashing a rom from the bootloader (using RUU), it always gives me a image corrupted error message.
i also can't flash a new radio. error 00018003 occurs when trying to flash a new radio.
currently i have ENERGY rom loaded into it but won't start. stuck on the NRG loading screen
Click to expand...
Click to collapse
Have you had your HD2 flashed with HSPL?
K so its happening more and more now, some times it gets to the Launching HTC Sense part of the boot and then shuts off and tries to reboot.
Any one seen this before or know a fix?
Or just doomed?
rysky007 said:
K so its happening more and more now, some times it gets to the Launching HTC Sense part of the boot and then shuts off and tries to reboot.
Any one seen this before or know a fix?
Or just doomed?
Click to expand...
Click to collapse
the original HD2 came with defected sdcards so if your using the one it came with then that's why it might freeze...
custom roms are better at using the phones resources... just cuz the old one worked fine with stock doesn't mean this one would
achen_you said:
Have you had your HD2 flashed with HSPL?
Click to expand...
Click to collapse
yes. SPL 2.08.HSPL Cotulla HSPL
i just tried task 29'ing it and still no luck. as well as mtty
whenever it hits Radio_V2, it gives me an error 00018003.
hakuchi18v said:
the original HD2 came with defected sdcards so if your using the one it came with then that's why it might freeze...
custom roms are better at using the phones resources... just cuz the old one worked fine with stock doesn't mean this one would
Click to expand...
Click to collapse
No using a diff 16 gig sd card, and even when i take it out it still does it,
The problem with the custom roms, I dont like how most of them look and dont want to spend all the time installing diff ones to see if I like it or not, dont have the knowledge or the time for it.
I am fine with the standard HTC sense, just want to figure out why this one keeps crashing on load, what the conflict is.
rysky007 said:
No using a diff 16 gig sd card, and even when i take it out it still does it,
The problem with the custom roms, I dont like how most of them look and dont want to spend all the time installing diff ones to see if I like it or not, dont have the knowledge or the time for it.
I am fine with the standard HTC sense, just want to figure out why this one keeps crashing on load, what the conflict is.
Click to expand...
Click to collapse
maybe u can download the TMobile HD2 rom from their website. you need to put in your IMEI to download. after that, from what i did with my tmous before, was enter bootloader then run the utility and it should work perfectly.
if it still doesn't boot up then im suspecting a hardware issue?
froibet said:
maybe u can download the TMobile HD2 rom from their website. you need to put in your IMEI to download. after that, from what i did with my tmous before, was enter bootloader then run the utility and it should work perfectly.
if it still doesn't boot up then im suspecting a hardware issue?
Click to expand...
Click to collapse
U got a link to the rom? or were I can find it?
Also were is a good set of instructions on how to install roms.
the link is the tmobile website. just look for hd2. dont be lazy
for roms, it uses a utility. all u gotta do is press next.
hi brother
my phone have the same issue as u have so any solution you find regarding ur htc hd2 please tell me i am waiting for your response
thanks in advance
if u can give me a favor please mail on that email address
[email protected]
froibet said:
yes. SPL 2.08.HSPL Cotulla HSPL
i just tried task 29'ing it and still no luck. as well as mtty
whenever it hits Radio_V2, it gives me an error 00018003.
Click to expand...
Click to collapse
wrong radio rom flashed?
rysky007 said:
Just got a new phone, worked fine, put in my sim and sd, all was working perfect, then I went to music selection and it saw my songs on my sd card, i started playing one, the phone froze and just played the last note like its stuck on it, all buttons would not work.
I took off the battery put it back on now when i power up it just sits on the white and purple screen that says " stick together" the tmoblie logo, and wont move from there.
Removed battery a few times same thing, pressed the little hard boot button same thing.
Any advice?
thank you in advance.
Click to expand...
Click to collapse
Bricked is when you flash the wrong radio, like I did, and your power button will not work. Phone will not power up at all.

Need Help. PLEASE!!!!!!

I can no longer get android to run on my HD2. Here are the details to my problem. Please I really need help, will make it well worth the while of anyone that can sort this problem out for me.
First off, I had been running android on my device for about a month. Then it started just going off and freezing at the android boot logo. Nothing I did would work unless I reinstall the rom.
Then that just stopped working and even after reinstalling a rom (nand) it would never get past the android boot logo after the go go go screen. It would just stay there then restart and the restart loop continues.
I have tried
- task 29
- flashing an official stock rom
- trying different radios even though the one in my sig worked with android just fine
- reflashing HSPL 2.08, MAGLDR and recovery
- formatting my SD cards (over and over again)
- trying different roms....etc
Nothing works. And I have lost count of how many times I have gone through all this.
Please take note that I did have android running on my EU HD2 with the HSPL, radio and rom in my sig on this very phone so I at least know what I am doing.
I just dont get this issue, cause windows mobile runs just fine on my device every single time. My cards read fine too. And even when trying to run an SD rom build, after haret starts up it cuts to the HTC logo and just hangs there too. And I am assuming that if it was my battery or my battery pins it would at least affect the phone generally and not only when trying to boot android.
Please, I really need help as this phone is practically useless to me now.
Any help would be greatly appreciated.
Lorddeff07 said:
I can no longer get android to run on my HD2. Here are the details to my problem. Please I really need help, will make it well worth the while of anyone that can sort this problem out for me.
First off, I had been running android on my device for about a month. Then it started just going off and freezing at the android boot logo. Nothing I did would work unless I reinstall the rom.
Then that just stopped working and even after reinstalling a rom (nand) it would never get past the android boot logo after the go go go screen. It would just stay there then restart and the restart loop continues.
I have tried
- task 29
- flashing an official stock rom
- trying different radios even though the one in my sig worked with android just fine
- reflashing HSPL 2.08, MAGLDR and recovery
- formatting my SD cards (over and over again)
- trying different roms....etc
Nothing works. And I have lost count of how many times I have gone through all this.
Please take note that I did have android running on my EU HD2 with the HSPL, radio and rom in my sig on this very phone so I at least know what I am doing.
I just dont get this issue, cause windows mobile runs just fine on my device every single time. My cards read fine too. And even when trying to run an SD rom build, after haret starts up it cuts to the HTC logo and just hangs there too. And I am assuming that if it was my battery or my battery pins it would at least affect the phone generally and not only when trying to boot android.
Please, I really need help as this phone is practically useless to me now.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
Have you tried running a CLK build or just MAGLDR or SD builds?
As far as i know (sorry if this is nonsense ) the HD2 runs natively on ppp not on rmnet, magldr (and sd?) pushes something in the radio so that rmnet can be used, maybe something in that direction went wrong with your phone?
Cheech1976 said:
Have you tried running a CLK build or just MAGLDR or SD builds?
As far as i know (sorry if this is nonsense ) the HD2 runs natively on ppp not on rmnet, magldr (and sd?) pushes something in the radio so that rmnet can be used, maybe something in that direction went wrong with your phone?
Click to expand...
Click to collapse
Well I have only been trying MAGLDR and SD roms but never CLK. Guess I can give that a shot. But assuming something weird is going on with my radio, shouldn't it have fixed itself considering the amount of radios I have used and the amount of task 29s I have done?
Thanks for the suggestion though, will give that a go today.
Lorddeff07 said:
Well I have only been trying MAGLDR and SD roms but never CLK. Guess I can give that a shot. But assuming something weird is going on with my radio, shouldn't it have fixed itself considering the amount of radios I have used and the amount of task 29s I have done?
Thanks for the suggestion though, will give that a go today.
Click to expand...
Click to collapse
Well before i get flamed by those who know better, i would ask you to look for threads covering this topic, i.e. the difference between ppp and rmnet and which one is used with which one etc.
I have read in another forum that the hd2 runs natively with ppp, but magldr pushes something "in" the radio rom while booting, so the radio looks like a desire, so the android builds can run on rmnet...
Or something like that, what i have gathered from this is, that there is a difference and since it sounded like you were running out of options, i thought i´d propose installing a clk build
Lorddeff07 said:
I have tried
- task 29
- flashing an official stock rom
- trying different radios even though the one in my sig worked with android just fine
- reflashing HSPL 2.08, MAGLDR and recovery
- formatting my SD cards (over and over again)
- trying different roms....etc
Click to expand...
Click to collapse
Can you elaborate "formatting my SD cards" a little?
As in how, which tools, were was the partitioning done if any?
Lorddeff07 said:
Well I have only been trying MAGLDR and SD roms but never CLK. Guess I can give that a shot. But assuming something weird is going on with my radio, shouldn't it have fixed itself considering the amount of radios I have used and the amount of task 29s I have done?
Thanks for the suggestion though, will give that a go today.
Click to expand...
Click to collapse
Hi,
Sometimes boot loops occur when the battery pins are out of shape.
Make sure all your battery pins are aligned and see if that helps.
Cheech1976 said:
Well before i get flamed by those who know better, i would ask you to look for threads covering this topic, i.e. the difference between ppp and rmnet and which one is used with which one etc.
I have read in another forum that the hd2 runs natively with ppp, but magldr pushes something "in" the radio rom while booting, so the radio looks like a desire, so the android builds can run on rmnet...
Or something like that, what i have gathered from this is, that there is a difference and since it sounded like you were running out of options, i thought i´d propose installing a clk build
Click to expand...
Click to collapse
Looking into trying a CLK build now. Actually just finished downloading one.
Cheech1976 said:
Can you elaborate "formatting my SD cards" a little?
Click to expand...
Click to collapse
Ok, i have a total of 3 SD cards. One 16GB, one 4GB and the last one 2GB. I have used both gParted and partition wizard. Did full 30 mins (approx) wipes on the cards and had them formatted to fat32. For the 16GB card I try that with the ext3/4 partions. Tried using both 4kB and 32KB cluster sizes.
And again, I had actually got android running on my phone before. And even tried different roms at that time so I have some idea what I am doing. I don't have any issues reading my cards either from a card reader or through the phone.
malybru said:
Hi,
Sometimes boot loops occur when the battery pins are out of shape.
Make sure all your battery pins are aligned and see if that helps.
Click to expand...
Click to collapse
Yeah read about that, I have tried straightening my pins and all that but nothing changes. And I would think that if the pins are the issue then I would at least hav some issues running windows mobile 6.5 too. I have never had such issues running WM ever. Android on the other hand just refuses to run.
Lorddeff07 said:
Yeah read about that, I have tried straightening my pins and all that but nothing changes. And I would think that if the pins are the issue then I would at least hav some issues running windows mobile 6.5 too. I have never had such issues running WM ever. Android on the other hand just refuses to run.
Click to expand...
Click to collapse
Hi,
The only thing I can think of is maybe some corrupt software along the way.
May I suggest using KSUBEDI's TOOLKIT (Don't forget to thank him).
Run through the whole process using his toolkit.
It worked for me.
Start from
HSPL 2.08 HSPL
Task 29
Radio HERE
Magldr
CWM partition for the ROM you intend to use
ROM
malybru said:
Hi,
The only thing I can think of is maybe some corrupt software along the way.
May I suggest using KSUBEDI's TOOLKIT (Don't forget to thank him).
Run through the whole process using his toolkit.
It worked for me.
Start from
HSPL 2.08 HSPL
Task 29
Radio HERE
Magldr
CWM partition for the ROM you intend to use
ROM
Click to expand...
Click to collapse
Just did all that (again). And exactly in that order. As always, it installs just fine but it always hangs on the android logo right after the go go go screen for about 20-30 secs then it restarts. Over and over again.
Lorddeff07 said:
Just did all that (again). And exactly in that order. As always, it installs just fine but it always hangs on the android logo right after the go go go screen for about 20-30 secs then it restarts. Over and over again.
Click to expand...
Click to collapse
Hi,
What ROM are you installing, and what CWM partition are you using?
Lorddeff07 said:
Ok, i have a total of 3 SD cards. One 16GB, one 4GB and the last one 2GB. I have used both gParted and partition wizard. Did full 30 mins (approx) wipes on the cards and had them formatted to fat32. For the 16GB card I try that with the ext3/4 partions. Tried using both 4kB and 32KB cluster sizes.
And again, I had actually got android running on my phone before. And even tried different roms at that time so I have some idea what I am doing. I don't have any issues reading my cards either from a card reader or through the phone.
Click to expand...
Click to collapse
Didn´t mean to let it sound like you don´t know what you´re doing, just trying to narrow it down and the sd cards can be the culprit for so many bugs, so it was worth a shot
Lorddeff07 said:
Just did all that (again). And exactly in that order. As always, it installs just fine but it always hangs on the android logo right after the go go go screen for about 20-30 secs then it restarts. Over and over again.
Click to expand...
Click to collapse
malybru said:
Hi,
What ROM are you installing, and what CWM partition are you using?
Click to expand...
Click to collapse
Especially the NAND partition used in flash.cfg would be interesting, maybe there´s something wrong with that, that would be consistent with the failure to boot, wouldn´t it?
Other than that, i have to admit, slowly but surely this leaves my area "of expertise"
I sure hope you get your phone running again! I´ll keep my fingers crossed!
malybru said:
Hi,
What ROM are you installing, and what CWM partition are you using?
Click to expand...
Click to collapse
I am installing HyperDroidGBX-v12[GRI54-2.3.3][a2sd+][TytR8.3] and using the required 150mb partition size. I had got this very rom and RAFDROID rom (though with a 400mb partition) to work on my phone previously.
I also got the a couple of SD based roms to work on my device before nand roms became available now even those dont work too.
Just tried CLK for the first time and flashed the CLK version of the aforementioned rom. Been on the white HTC screen for about 10mins now.
Cheech1976 said:
Didn´t mean to let it sound like you don´t know what you´re doing, just trying to narrow it down and the sd cards can be the culprit for so many bugs, so it was worth a shot
Especially the NAND partition used in flash.cfg would be interesting, maybe there´s something wrong with that, that would be consistent with the failure to boot, wouldn´t it?
Other than that, i have to admit, slowly but surely this leaves my area "of expertise"
I sure hope you get your phone running again! I´ll keep my fingers crossed!
Click to expand...
Click to collapse
Trust me, no offense taken what so ever .
I am aware that SD card errors could be the issue, but all three SD cards? even stranger since I have never used 2 of those 3 for any android install.
What really puzzles me though is that regardless of whatever issues i seem to be having... windows mobile runs just fine every single time. My only guess now may be that teher may be something wrong on the hardware side with how my SD card and phone syncs so something always goes wrong during the install. If that is the case the only possible solution would be if it was some how possible to install a rom directly from my PC without using an Sd card at all.
Lorddeff07 said:
Trust me, no offense taken what so ever .
I am aware that SD card errors could be the issue, but all three SD cards? even stranger since I have never used 2 of those 3 for any android install.
What really puzzles me though is that regardless of whatever issues i seem to be having... windows mobile runs just fine every single time. My only guess now may be that teher may be something wrong on the hardware side with how my SD card and phone syncs so something always goes wrong during the install. If that is the case the only possible solution would be if it was some how possible to install a rom directly from my PC without using an Sd card at all.
Click to expand...
Click to collapse
Hi,
That would mean making a DAF.exe file and install it the old fashioned way.
Sadly,beyond my level of expertise.
Good luck.
Lorddeff07 said:
Trust me, no offense taken what so ever .
I am aware that SD card errors could be the issue, but all three SD cards? even stranger since I have never used 2 of those 3 for any android install.
What really puzzles me though is that regardless of whatever issues i seem to be having... windows mobile runs just fine every single time. My only guess now may be that teher may be something wrong on the hardware side with how my SD card and phone syncs so something always goes wrong during the install. If that is the case the only possible solution would be if it was some how possible to install a rom directly from my PC without using an Sd card at all.
Click to expand...
Click to collapse
Sorry but i am at a loss for any further possible advice for you. I would propose the build i am using for you to install.
It installs with the according daf.exe and after that you can install the zip file via cwm. I never flashed another android build myself, what with all this nand partitioning (i have heard of it, but never had to set it up myself), so i don´t really know how the nand partitioning is done without daf.exe and the according flash.cfg file.
Cheech1976 said:
Sorry but i am at a loss for any further possible advice for you. I would propose the build i am using for you to install.
It installs with the according daf.exe and after that you can install the zip file via cwm. I never flashed another android build myself, what with all this nand partitioning (i have heard of it, but never had to set it up myself), so i don´t really know how the nand partitioning is done without daf.exe and the according flash.cfg file.
Click to expand...
Click to collapse
Thanks, will try. I have given up though. been working on this thing for too long. Guess its time to buy the galaxy s2. I really loved this phone. And windows mobile just doesn't cut it.
Lorddeff07 said:
Thanks, will try. I have given up though. been working on this thing for too long. Guess its time to buy the galaxy s2. I really loved this phone. And windows mobile just doesn't cut it.
Click to expand...
Click to collapse
Hi,
Just before you bin it,how have you been formatting the sd card?
Have a look at this:
"You should also properly format your sdcard with Panasonic SDFormatter (Full+Overwrite+size adjust). Then in recovery>advanced>sd partition (1GB+0MB swap) If you have a EU HD2 and need the extra data storage/rom requires it. "
Worth a shot.
Dont give up!
Might be a long shot, But have you tried turning off your antivirus software during the installation? Ive seen a few of your posts about and i hope you get it to work again. Bet your sick of the sight of task29 lol
malybru said:
Hi,
Just before you bin it,how have you been formatting the sd card?
Have a look at this:
"You should also properly format your sdcard with Panasonic SDFormatter (Full+Overwrite+size adjust). Then in recovery>advanced>sd partition (1GB+0MB swap) If you have a EU HD2 and need the extra data storage/rom requires it. "
Worth a shot.
Click to expand...
Click to collapse
yeah I have tried that too. Still leaves me hanging at the android logo right after the go go go screen. Truth is that I have come to the conclusion that nothing i am doing will actually work. Cause all these things mentioned now I have already done and didn't even need to do half of them at one point when i was actually running android on my phone.
The fact that I cant even run the SD card builds of android just goes to show that something must be very wrong with my phone now. It could be battery related or something but that doesn't make sense either cause WinMO 6.5 roms work fine every singel time.
I just dont get it really.
fuuunkdat said:
Might be a long shot, But have you tried turning off your antivirus software during the installation? Ive seen a few of your posts about and i hope you get it to work again. Bet your sick of the sight of task29 lol
Click to expand...
Click to collapse
Lol.... you have no idea lol
Its sad no doubt, but I am actually happy for the amount of help offered by a lot of ppl here in the xda community.
So at least I am taking it all in good spirits. Oh, I have probably tried that at one point too....
The only thing I can think of now is to flash my HSPL back to spl 1.66 and revert back to factory setting, then try and reflsah the 2.08 HSPL. Though I dont know what difference taht will make considering how many times i have reflsahed the very same 2.08 HSPL so at least i know I have a clean fresh one on my phone now lol.

[Q] whats the easiest way to install android

Hi, I have the hdc hd2 with spl 3.03.0000 xe, and radio 2.15.161.3.
You maybe able to tell by that that im new to this, but want to install android as i dont like windows 6.5. I've managed to install a stock windows rom with the information i've learned here. But now i need help.
I want to install froyo or gingerbread as ive used these before on other phones.
So what is the easies way to do it and wheres the best place to get the rom from.
Please try to make it as simple as possible, Thanks.
It depends, do you want NAND Android or are you happy with running SD Android? Basically, if you want SD Android it couldn't be simpler. Just go to the SD section, download a build, place the Android folder on the root of your SD card and hit CLRCAD then HARET in the file manager. If you want NAND Android it's still pretty straightforward. Follow this guide and you should be fine. If you find even this guide too complex try using the NAND Toolkit. If you can't use that, don't bother flashing NAND Android and stick with SD Android.
Have you tried using Google? <<< I'm flaming.
Why didn't you look for the Newbies' Guides that are floating everywhere? they will guide you from the moment you pay for your phone till you are welcomed with Android's welcome screen. <<<I'm trying to be nice.
Here you go : http://forum.xda-developers.com/showthread.php?t=893948 , from start to finish. <<< I'm being nice.
Choose wisely ...
EDIT:
It always takes more time to write a poem than it does to write an article
You were faster this time, Nigel
Edit v1.1:
lol, I guess you're right, It's a double win . Furthermore, I just couldn't b.a. to look for a recent guide, I simply made a quick google about guides for hd2-android and this came up, didn't really check it
Next time, I'll be faster ..... and use bigger words
Marvlesz said:
Have you tried using Google? <<< I'm flaming.
Why didn't you look for the Newbies' Guides that are floating everywhere? they will guide you from the moment you pay for your phone till you are welcomed with Android's welcome screen. <<<I'm trying to be nice.
Here you go : http://forum.xda-developers.com/showthread.php?t=893948 , from start to finish. <<< I'm being nice.
Choose wisely ...
EDIT:
It always takes more time to write a poem than it does to write an article
You were faster this time, Nigel
Click to expand...
Click to collapse
Muahahahaha, I win Also, you linked an outdated guide for the DFT Stock desire build, so I double win (if that's possible)
Thanks guys after more reading and searching i think i should go the nand root.
This means i need hspl on it it first and i can only install this if i have spl 1.42.0000. Mine says spl-3.03.0000. It also says installing a stock rom will roll this back. I've installed stock win rom yesterday and it didnt touch the spl.
Can i still install hspl with this or do i need it?
Is there a list of available roms on this site?
tradvang said:
Thanks guys after more reading and searching i think i should go the nand root.
This means i need hspl on it it first and i can only install this if i have spl 1.42.0000. Mine says spl-3.03.0000. It also says installing a stock rom will roll this back. I've installed stock win rom yesterday and it didnt touch the spl.
Can i still install hspl with this or do i need it?
Is there a list of available roms on this site?
Click to expand...
Click to collapse
*sigh* did you read Marvlesz's post about Google? Download HSPL4 and use it to flash HSPL 2.08, no ROM downgrade is necessary. Basically after you've done that it's as simple as flashing MAGLDR, CWM and your ROM (and trust me, all of that won't take you more than 30 minutes at the very most).
Marvlesz said:
Next time, I'll be faster ..... and use bigger words [/B]
Click to expand...
Click to collapse
Lol, just got that part
Thanks again got the hepl bit done, downloading a rom now got MAGLDIR113 down and ready.
Having problem getting phone to sync with vista on pc, it just wont do it. Got it to sync on the laptop ok, any ideas with pc problem? Keep getting rapitool errors.
tradvang said:
Thanks again got the hepl bit done, downloading a rom now got MAGLDIR113 down and ready.
Having problem getting phone to sync with vista on pc, it just wont do it. Got it to sync on the laptop ok, any ideas with pc problem? Keep getting rapitool errors.
Click to expand...
Click to collapse
Check your device manager did u see mobile device? and is it working?
if not try to Reinstall the WMDC driver?
I used to have this problem too after i reinstall the driver the phone will be detected again.
However if u still can't connect the phone to your PC (it's driver problem, i think).
Try task 29 Change to cLK for me it fixed everything. (using HD2 toolkit is easiest way)
Sorry for being a bit dumb here but stuck again.
I've downloaded 4 roms-
danik supersonic v1.0 lite
boxmax.s3.5v8.0.magldr
boxmax.s3.5v8.5.magldr
boxmax.s3.5.v8.5.haret.sd
unzipping the first 3 provide no DAF.exe or install.exe, so stuck there.
unzipped the last and copied to sd card and the phone just stalls on the htc quietly brilliant screen.
What can i try next?
tradvang said:
Sorry for being a bit dumb here but stuck again.
I've downloaded 4 roms-
danik supersonic v1.0 lite
boxmax.s3.5v8.0.magldr
boxmax.s3.5v8.5.magldr
boxmax.s3.5.v8.5.haret.sd
unzipping the first 3 provide no DAF.exe or install.exe, so stuck there.
unzipped the last and copied to sd card and the phone just stalls on the htc quietly brilliant screen.
What can i try next?
Click to expand...
Click to collapse
Which guide did you follow? The one I posted or the one which Marvlesz posted? Use the one I posted because the one he posted is outdated. You install CWM then flash the ROM as a zip file. I really have no clue how somebody can find it so difficult to follow simple instructions: DOWNLOAD A NAND ROM, NOT AN SD ROM. You've said that you want a NAND ROM and then you try to flash an SD build? At least have some common sense, please. Unless you have a problem which cannot be solved by reading in the future I refuse to give any more help, because it appears to be hopeless
thanks again i've learned alot more tonight, got my first flash done just waiting for it to load. Last question before i leave you alone Is there a way to tell the difference between which mods are CWM and which wont work.
tradvang said:
thanks again i've learned alot more tonight, got my first flash done just waiting for it to load. Last question before i leave you alone Is there a way to tell the difference between which mods are CWM and which wont work.
Click to expand...
Click to collapse
Basically all ROMs use CWM, other than the DFT Stock Desire ROM. For everything else, just download the MAGLDR version of the ROM if there is one (many ROMs automate MAGLDR/cLK), change your system partition to the required size and flash the ROM.
hi tried downloading 6 roms now
DFT_LEO_NAND_Android
BoxmaX.S3.5.v.8.5.Magldr
For.user.Nand.v8.x
BoxmaX.S3.5.v.8.5.Haret.SD
BoxmaX.S3.5.v.8.0.Magldr
DFT_LEO_MAGLDR113_DAF
Android_2.3.5_Danik_Supersonic_v.1.0_Lite
Put all of them on the memory card and it only recogognises the Danik one when i go to choose zip from sd card.
When i try to load that it goes through ok till i reboot then it freezes at the HTC screen.
tradvang said:
hi tried downloading 6 roms now
DFT_LEO_NAND_Android
BoxmaX.S3.5.v.8.5.Magldr
For.user.Nand.v8.x
BoxmaX.S3.5.v.8.5.Haret.SD
BoxmaX.S3.5.v.8.0.Magldr
DFT_LEO_MAGLDR113_DAF
Android_2.3.5_Danik_Supersonic_v.1.0_Lite
Put all of them on the memory card and it only recogognises the Danik one when i go to choose zip from sd card.
When i try to load that it goes through ok till i reboot then it freezes at the HTC screen.
Click to expand...
Click to collapse
Screw it, I can't help you if you're this f**king stupid.
Cheers nasty c*nt.
tradvang said:
Cheers nasty c*nt.
Click to expand...
Click to collapse
Is that how you say thanks to those who were trying to help you ?
Follow this : http://forum.xda-developers.com/showpost.php?p=16528026&postcount=7 شبر بـ شبر and you should have Android by the end of its steps.
(btw, post reported)
I've said thanks before for his help. Ive asked for the difference between mods and how to differenciate them, i cant work out out why only 1 out of 6 is recognised. And i've downloaded the magdlr versions as suggested.
Then he calls me f*cking stupid. Think i have every right to be p*ssed off.
What do you mean by "Difference between mods" ? All mods come in a .zip package that is flashed in CWM.
When you download something (any mod, rom, kernel or anything) off the NAND section (this : http://forum.xda-developers.com/forumdisplay.php?f=928 ) it is going to be a flashable CWM. (Unless noted)
But when you download something off the SD section ( this: http://forum.xda-developers.com/forumdisplay.php?f=735) it is going to be ... well ... to be put on the sd without flashing.
Is this what you are asking for ?
Nigeldg said:
Which guide did you follow? The one I posted or the one which Marvlesz posted? Use the one I posted because the one he posted is outdated. You install CWM then flash the ROM as a zip file. I really have no clue how somebody can find it so difficult to follow simple instructions: DOWNLOAD A NAND ROM, NOT AN SD ROM. You've said that you want a NAND ROM and then you try to flash an SD build? At least have some common sense, please. Unless you have a problem which cannot be solved by reading in the future I refuse to give any more help, because it appears to be hopeless
Click to expand...
Click to collapse
tradvang said:
I've said thanks before for his help. Ive asked for the difference between mods and how to differenciate them, i cant work out out why only 1 out of 6 is recognised. And i've downloaded the magdlr versions as suggested.
Then he calls me f*cking stupid. Think i have every right to be p*ssed off.
Click to expand...
Click to collapse
Sorry, but I have every right to call you stupid too. I even posted DOWNLOAD A NAND ROM, and you go on and download ROMs from the SD section? It's frankly pathetic if you can't do that little reading, and if I were you I wouldn't bother flashing anything in the future. You're lucky you have a pretty much unbrickable device, because if you didn't I'm sure you would be sitting right there with a useless piece of hardware right now.
Thanks Marvlesz, thats got me sorted, the problem was when he said just download the "MAGLDR version", i thought anything with that in the name was the correct one. I'm not here to get into a slanging game so i'll just leave it that.
Thanks again.

Categories

Resources