Database Users

Locked up, please help

Hi,
I have a tmobile MDA (wizard). I attempted to install some software on it, but disconnected and rebooted before it was complete (it appeared to be just spinning).
Now after a soft reset, screen shows only 'Windows Mobile' after booting, and none of the buttons work and I can't advance from this screen.
Is there a way to hard reset that doesn't involve using the OS (ie, I can't click on anything because it's not getting to that point).
Also in this state activesync isn't detecting device.
Thanks in advance! - Chris

Hold down (and keep holding) the camera button while depressing the reset button. Hopefully it boots into a tri-color screen. If so, plug it into the USB port and, at the bottom of the screen, it should display "USB". If that happens, flash it with a *known good rom*, such as a stock T-Mobile rom. Don't try to be clever, the object is to get the phone working. Once the flash has started, *get up and walk away* for 15 or 20 minutes. Don't check in on it, leave it alone, It takes some time. When you hear it's little chime, it's done, rebooted and ready. If any of the above doesn't happen or the flash outright fails, then you may have trashed it permanently. It doesn't sound like it's beyond hope yet, however.

i have the wizard and im having the same problem after installing a ROM from this website...it just goes to the windows mobile screen with the numbers then shuts off...id really like to save my phone is there anything else i can try because that hard reset thing isnt working

axxeman001 said:
Hi,
I have a tmobile MDA (wizard). I attempted to install some software on it, but disconnected and rebooted before it was complete (it appeared to be just spinning).
Now after a soft reset, screen shows only 'Windows Mobile' after booting, and none of the buttons work and I can't advance from this screen.
Is there a way to hard reset that doesn't involve using the OS (ie, I can't click on anything because it's not getting to that point).
Also in this state activesync isn't detecting device.
Thanks in advance! - Chris
Click to expand...
Click to collapse
Well same thing happened to me a few days back.. I had to Cold Reset [which restored it to factory defaults], but hey I got it working again..
Press Communication Button [Top Left] and Record Button [Top Right] at the same time and use the stylus to soft reset..
You will get a black screen, asking you to press "Send" to reset to "Factory defaults"
Press "Send".
Hopefully you should get your MDA working again ...
I read the "Above" in the HTC Wizard Service Manual [PDF] on the *last page* under the "Cold-reset" Section..

SoftBricked Tmobile UK G1 ?

Firstly i would like to say hello and happy new year.
Now to the point,
Yesterday I dropped my phone in the snow and it got a bit wet
I assumed it would be ok.
Few mins after this a received a call and couldn't hear the caller so i suspected that there was water in the receiver so i took my phone apart and tried to dry it out (even though i couldn't see any water in it)
The thing is when i put the phone back together it came to the bootloader and said no image file on a gray screen
I assumed that it was looking for a Dreaimg.nbh file
I put one on my sdcard and attempted to recover the device.
This looked to have worked initially but when i restarted the phone i was presented with a bootloader screen again with the red, green and blue bands saying "serial0".
I assumed that the device was looking for a ROM and couldn't find it so it took me back to the bootloader.
I went online and downloaded a rc8 update.zip
I restarted the phone again and went in to recovery mode (where you update with the update.zip) pressed "alt+l" then Alt+w and then alt+s to flash with my latest update. and tried to reflash the phone from recovery by pressing Alt+s this seemed to work initially but failed after the 2nd restart the process went like this.
Turn on phone press home key
I get a triangle ! and a phone so pressed Alt+l (to bring up the options)
pressed Alt+w to wipe the phone
pressed Alt+s to apply the update.zip
waited,
phone said it was done and press Home+back to reboot.
when i pressed Home+Back before the phone rebooted a message came up saying that it was flashing the radio (is this normal)
Phone rebooted to the G1 screen ]
Then on to a screen with the Microchip on it with a yellow and orange arrow stayed on there for a while and then rebooted again to the g1 screen then on to a screen with a status bar and a package with an arrow within a second the phone reboots and we go back to the bootloader.
This is all my phone will do
Please can some one help me with this I am an IT professional but this has me beat.
Thanks in advance Emove

I am stuck with the same issue. This happened a day after i split some soda on keyboard.
The G1 is auto powering in fastboot mode even though the camera button isnt stuck.
Sometimes I manage to turn on the phone it works fine until it has the problem again and it drains the battery.

Mine in other respects is fine I was hopeing that my problem was fixable but no one has replied with any real comments that may help so i suspect that that no one knows what the problem is.
I would suspect that you have a short somewhere on the board. Soft drinks leave a residue on the PCB when they dry so maybe thats your problem.
your options are to deal with it as it is.. have it cleaned professionaly (t-mobile/htc) or if your brave/stupid like me try and service it your self. cleaning with alcohol should do it no harm if its already on its way out.
i do have the service manual if you need it.

[Q] Help! Wildfire crashed, tried hard reset and it won't restore!

Hi all,
I had a terrible catastrophic failure today with my 1-month old HTC Wildfire. I bought my device new, unlocked, in Singapore.
Here's what happened:
Today I received an ordinary SMS (like I have hundreds of times before in the past few weeks) and when I picked up the phone off of the desk, flipped on the screen, and slid my finger to unlock it, I saw a brief error message in a dialog on top of the Messages app. It was something like "com.something .... ", I didn't get a good look at the error but it didn't really mean anything to me at the time. The SMS that I received was then lost (I knew who it was from, but the message was not showing up). A few minutes later, I heard another SMS notification. No error message this time, but again the message did not show up in my Messages app.
So, I pressed the power button to power cycle the phone. After I shut it down, I turned it back on, saw the white screen with HTC logo, then black. It was dead. No amount of pressing buttons did anything.
After a few minutes, I removed the battery and it turned on again. Again, white splash screen and then darkness. Repeated this several times and same result.
Finally, I googled how to do a hard reset. I followed the instructions, held the volume down button while pressing power, cleared the memory, after it restarted it went right back to the white bootloader screen, flashed some error messages, and now I'm stuck in the bootloader. When I select the RECOVERY option, I get a quick screen with something like:
SD Checking ...
Loading [SOMEFILE.zip] ...
No Image!
Loading [SOMEFILE.zip] ...
No Image!
....
....
No Image or Wrong Image!
Can anybody help??! I don't know what to do now. I've searched for this "No Image or Wrong Image" message on these forums, but all the results are about rooting and loading different ROMs. I've never rooted or anything out of the ordinary, I just want the stock OS back and operational.
Btw ... I'm an Android noob, but an experienced Linux/Mac user and 10-year software developer.
Any help is greatly appreciated.
Thanks,
Nate

Recovery mode is something else.
To do a hardreset try the following:
Performing a factory reset using phone buttons
If you cannot turn on your phone or access the phone settings, you can still perform a factory reset by using the buttons on the phone.
1. With the phone turned off, press and hold the VOLUME DOWN button, and then briefly press the POWER button.
Note: If you are not sure whether your phone's power is turned off, remove and then reinsert the battery.
2. Wait for the screen with the three Android images to appear, and then release the VOLUME DOWN button.
3. Press VOLUME DOWN to select CLEAR STORAGE, and then press POWER.
4. Press VOLUME UP to start the factory reset.
Click to expand...
Click to collapse
Source : http://www.htc.com/www/howto.aspx?id=3567&type=1&p_id=316

Call HTC support. I had a problem with my previous HTC phone, and they took me through diagnositcs over the phone, and when they diagnosed a hardware fault, sent a courier to pick it up from me the next day. This was when the phone was 18 months old. No receipt was necessary, they used the serial number/manufacture date.
Downside: the phone was gone a week, and came back still broken. It was sent away again, and came back fixed. So painfully without it for two weeks, but not a bad experience.
(edit: it was a similar problem: I upgraded to windows 6.1, and my phone wouldn't get past the initial hardware/boot screen)

I tried the hard reset procedure several times. Every time it's the same thing. After it clears the memory, it says "Reboot in 5 seconds..." and then when it reboots, it goes back to the bootloader screens.
I've contacted HTC support via email, and I'm bringing it in to their support center in Singapore tomorrow. I really hope it doesn't take a week ... I'll keep you updated.

Fixed.
I just got my Wildfire back today after a full week in the repair center. Apparently they replaced the main system board. No other explanation for the problem was given.
The repair process itself was hassle free, although I was frustrated by not having my phone for a week. Ended up having to buy a cheap basic phone for $55 to get by on SMS and voice.

Please help. My Milestone 2 is DEAD

Hi all,
I have had loads of problems with this phone, so I decided to do a factory reset.
It rebooted as normal until it got to the Motoblur setup page
It asks for the Motoblur details to be entered, but once you have entered them and pressed the 'next' button, it goes back to the previous screen instead of the next step and then gets stuck in a never ending loop.
I've tried skipping the sign in process but instead of skipping it, it just goes back to the first Motoblur account setup screen instead.
Out of desperation, I have tried to make several new Motoblur accounts but every single time, it gets to 80% completion, then stops.
I have even left running all night (plugged in) and it still freezes at 80%
I can't do another factory reset because it won't get past the Motoblur setup screen.
I've tried to do a hard reset by holding x and powering the phone on but this doesn't work. It just brings up the triangle and android robot but it does not go to the next step despite me leaving it for several minutes.
Only had it for 7 weeks and am awaiting a response from Expansys on what to do.
Any help from you guys will be greatly appreciated.

Apply a debrand image of your system and do a full wipe

phorenzik said:
I've tried to do a hard reset by holding x and powering the phone on but this doesn't work. It just brings up the triangle and android robot but it does not go to the next step despite me leaving it for several minutes.
Click to expand...
Click to collapse
Have you pressed the @ key when you get to this step with the robot and the triangle? That should bring up the reset menu, and then you use the volume and camera buttons to choose and select the option you require.
Cheers,
Steve.

StevePritchard said:
Have you pressed the @ key when you get to this step with the robot and the triangle? That should bring up the reset menu, and then you use the volume and camera buttons to choose and select the option you require.
Cheers,
Steve.
Click to expand...
Click to collapse
I didn't know you had to press @
Thanks
I've done a hard reset, but I still have the exact same problem.
If I try to input my proper Motoblur details it instantly says connection failed (it doesn't seem to even try to connect as fails the instant you press 'next)
Creating a new account hangs at 80%
Any more ideas before I throw it against a wall?
I notice there was an option to boot from SD in the recovey mode.
Would this allow me to boot an official motorola rom?
If so, where would I get the rom from?
A walkthorugh on exactly how to do this would be appreciated if this method could fix my issues.
I'm really annoyed because I sold my HD2 for this phone and I'm regretting it.
Thanks

phorenzik said:
I didn't know you had to press @
Thanks
I've done a hard reset, but I still have the exact same problem.
If I try to input my proper Motoblur details it instantly says connection failed (it doesn't seem to even try to connect as fails the instant you press 'next)
Creating a new account hangs at 80%
Any more ideas before I throw it against a wall?
Thanks
Click to expand...
Click to collapse
I think you need internet connection in order to validate your account or create a new one. Check your APN settings first, or do it on wifi.

Hi,
I've tried it whilst connected to my wifi router. I've even tried it via the data connection but nothing happens.
It seems that despite the data/wifi connections being there, it just ignores them.
I think this is the issue. It's not connecting and I don't know why
The phone displays the wifi/3G data symbols in the task bar but it doesn't seem to be using them during the Motoblur setup

Mine is dead too!!!
Hello everybody,
Greetings from sunny, flooded, blown away, Queensland Australia!
Long time lurker, first time poster...
I have a...
Vodafone-Australian-2.2-Milestone2
2 weeks old and its an expensive paper weight. It was rooted and thats about it, had a bunch of root required apps on there, installed the bootstrap, but hadnt installed Xrecovery yet.
I was playing around the other day. changing settings, installing and uninstalling a heap of apps, testing them. Some app suggested I restart or it restarted itself, cant recall, and that was the end. Boots until it gets past the M, and then its just bootloop city.
Won't register on comp in RSD or anything. Will boot to stock recovery and cleared cache and data several times, but that didnt fix anything. Won't even charge the battery. It will run an update but has to be signed. Problem is, we havent had any updates yet on these phones in Australia and there are no custom roms. What update.zip could I get to try to fix it, because I think thats about my only hope.
While recovery was wiping the data and cache it would stop frequently and each time I would touch the ok in the bottom corner of the screen and it would continue, and seemingly despite the 10 or more stops, completes fine. Surely thats not normal.
Out of ideas, I would just send it back with a story but the vodafone boot animation is replaced with disco flashing lights. and thats all it does, non-stop. Do you think they will notice someone has been tinkering?
Ideas? Thoughts?
Oh, and forgot to mention, when I first got it I had the same problem with the Motorola sign in wizard on startup, for quite a while, cant remember how I got around it though. Stop trying to sign in and just get out of that wizard, install ADW Launcher or similar and dont go near any Moto apps. You are only required to do a Gmail sign in, not Moto.

That's the problem though.
I'm stuck at the Motoblur sign in and it will not skip.
Whenever I select skip, it just goes back to the motoblur sign in page instead of going to the home screen.
Basically, in a nutshell, this is what's wrong:
I can't sign in to motoblur (gets stuck in a loop)
I can't create a new motoblur account (crashes at 80% every time)
I can't skip the sign in process (takes me back to the motoblur sign in page instead of loading home screen)
This is my first and last Motorola phone. Not good at all.

So what happens if you press press home or back repeatedly instead of skip? And if all fails reflash new SBF

benking1972 said:
So what happens if you press press home or back repeatedly instead of skip? And if all fails reflash new SBF
Click to expand...
Click to collapse
It just goes back to the motoblur setup/signin screen no matter how many time I press home, back or skip. It's as if a dll is missing and it's unable to boot to the home screen.
How do I flash a new SBF?
Motorola have agreed to let me return it but if I can do it myself I'd rather do it.
I have found this guide http://forum.xda-developers.com/showthread.php?p=11155476#post11155476
but the link to the UK SBF is dead

Yeah, that's the one, and the link to UK SBF works fine for me. If you can't get it to flash that way, then you are going to have to do it the way I am about to do mine, which is...
http://forum.xda-developers.com/showthread.php?t=804088
Failing that, send it back and be done with it.

since its so new id send it back. you shouldnt be having this problem at all. the milestone 2 is a very solid phone. i had mine running for 90 days straight not even a reboot or crash or anything lol. sounds like you just got a duff one. with any piece of technology theres bound to be a few that slip through the net. even if you find a fix for your problem you dont know what is causing it. and if youve had problems before then somethings obviously wrong. since theyve agreed to let you return it then thats your best option.

Probably i should send mine one back as well.
Bought a new Milestone 2 yesterday (from ebay, Chinese guys but as per retail package phones are for UK market). Put the SIM in just to check before wiping out everything from my old Defy. Made a call, checked the version and the menu and put the SIM back to Defy to backup all I needed. Plugged Milestone to the mains. 3 hours later found promising "Fully charged" on the screen and put the SIM in. That was it... Since I can't power the phone whatever I do. I thought the Power button went off as I tried to perform hard reset (x+Pwr), BRM (Arrow up+Pwr) and nothing happent at all. But then I put the phone on the charger again and the Power button worked fine switching the screen off and back on.
Any other methods to get the phone running?
UPDATE: It's strange and weird, but I've just had an idea to remove SD card and it worked - the phone powered on immediately!! Formatted the card using card reader, put it back - the phone works flawlessly. Fantastic! =))

Is my HD2 dead?

All of sudden, my HD2 died on me when I was using it with CoPilot during my driving. I stopped my car, took out the battery & back on and powered it on. Then loaded up some apps before it started to reboot again. And again. Until it reached the point where it just shows the "HTC" logo and freezes there. I left it switched off for a few days.
Now, today, I powered it on, it showed the HTC logo and then shut down. No reboot.
I have not done a reset yet as I need some data off from it first.
Standard Windows Mobile v6.5. That's it. I can't even get the red text at the HTC logo to come up with the radio number & other details.
Does anyone know what the issue is? Is there a way to get it bacjk up & running without losing my data?
Thanks all

First try a factory reset, press both volume up and down hold in then press the power button wait until you get the banded screen then the white screen - read the instructions.
If its booting its not bricked
Remove your sd card recover what you need then reformat it useing the pc, try EASEUS free edition remove all pertitions before formating
When its booted back correctly, I would consider a task 29 then reinstall the rom of your choice (the search option works well) Good luck

OK, after trying a few battery unplug/plug, I finally got the red text to come up...
R - 2.07.51.22.2
G - 15.32.50.07U
D - 1.66.76641
But it's still stuck at the HTC logo.

johnerz said:
First try a factory reset, press both volume up and down hold in then press the power button wait until you get the banded screen then the white screen - read the instructions.
Click to expand...
Click to collapse
Thanks, I assume doing the factory reset will wipe off whatever I have on the phone memory?

tsutton said:
Thanks, I assume doing the factory reset will wipe off whatever I have on the phone memory?
Click to expand...
Click to collapse
Yes a hard reset will remove all of your personal data and settings. Before you Hard Reset if you have not already done so. Check your battery pons to make sure you do not have a pin that is slightly bent. I say do thiscause you said it started bootlooping when hou took the battery out, I recommend using the reset button to soft rese.
Also try placing your HD2 in the freezer for like 10 minutes in a plasgic bag to protect it againsg moister and then see if it will boot.Also remove your SD card and see if that helps.

Has given up, did a factory reset and all is good. But sad about the data loss.
Nevermind, moving onward!
Thanks for the helps, all.

tsutton said:
Has given up, did a factory reset and all is good. But sad about the data loss.
Nevermind, moving onward!
Thanks for the helps, all.
Click to expand...
Click to collapse
if its on your dash it may have overheated... causing the issue.
sometimes happens to mine.