Database Users

Bricked? Stuck at gray loading screen

I've been hacking/modding/flashing for years with numerous devices and have never been this far down this path...I searched around and haven't found an answer or the same situation so I'm sorry if I overlooked a similar thread.
I've been running WP7 on my HD2 for a few months after running Android from the SD and NAND for a few months before that. Yesterday my touchscreen started getting VERY difficult to use, with it being both innacurate and unresponsive. It got progressively worse so this morning I reflashed the WP7 ROM without any problems. Even after that it continued getting worse to the point where the phone was unusable because the touchscreen would not respond to anything so I couldn't unlock the phone. The hardware keys worked fine. So I decided I would try to go back to WM6.5 in an attempt to isolate whether it was software or hardware. I'm on my work computer so it doesn't have the proper drivers for flashing, so I formated my SD card, put a TMO-US WM6.5 build on the root of the card, renamed it LEOIMG.nbh and put it back in.
I booted to the tri-color screen, pressed power to confirm the flash. It flashed the progress bar and then went to the loading screen. It stayed there for around 30 minutes so I pulled the battery out and attempted to try again, but then a screen comes up for a half second that says "Software update Failed! Please Try Again" and then it goes back to the loading screen. If I try to go back to the Tri-color screen it shows it for a second and says "ROM code error Please try again" then returns to the loading screen. Anybody have any advice? Anybody seen this before?

Got a full filename for the rom you flashed?
In bootloader what's the full spl line say?
What size SD card? The stock tmous one?

wow.. unless some how the flash to wm conflicted with magldr that should had worked...
When you start the phone holding down the volume key... Do you have the SDcard still in it and it just kicks you out of the bootloader? Technically ad long as the boot loader shows up it should be fixable but it kicks you out.. that a problem

samsamuel said:
Got a full filename for the rom you flashed?
In bootloader what's the full spl line say?
What size SD card? The stock tmous one?
Click to expand...
Click to collapse
This is the ROM I was flashing on the SD:
RUU_Leo_1_5_TMOUS_2.10.531.1_Radio_Signed_15.34.50.07U_2.08.50.08_2_Ship.zip
I got it from here:
http://forum.xda-developers.com/showthread.php?t=655653
The bootloader says 2.08.0000 then MicroP something. It just flashes so it is hard to read too fast.
I am using an 8GB Class 4 card. I also tried it with the stock 16GB one but it did the same thing. When I tried flashing it, however, it was the 8GB card.

hakuchi18v said:
wow.. unless some how the flash to wm conflicted with magldr that should had worked...
When you start the phone holding down the volume key... Do you have the SDcard still in it and it just kicks you out of the bootloader? Technically ad long as the boot loader shows up it should be fixable but it kicks you out.. that a problem
Click to expand...
Click to collapse
That's what I'm gathering as well. In my experience I've never been afraid of bricking because I've always been able to get to the bootloader. In this case, I can get to it, but it won't let me stay in it.

I finally got the phone to stay in bootloader mode, however when I try to flash any ROM, whether Task29, radio, stock, or cooked 6.5 it goes through the ROM Update Utility steps and then it stops at 0% for a few minutes before giving me an update communication error. This is what the Bootloader says:
PB81120 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Upgrade ROM code error
Please Try Again
Thanks again for the help.

YOU donT have HSPL... Thats why flashing a cooked rom isnt working aswell ad everything else... flash a stock rom to get it up and running
Sent from my HTC HD2 using XDA App

Yep, there's the problem. Any spl ending. 0000 is stock, you have 2.08.0000, you actually need 2.08.hspl.
Don't feel too silly though, its the most basic error there is, but still turns up daily.

When you flash a stock Rom from the SDCard it removes the HSPL... So you can try flashing a Stock ROM to see if the screen issues continue or put HSPL back on and flash something to it

also, what size is your SD card? Quite often, SD Cards over 2GB in size fail for rom updates via the SD Card method.
You could also go here: http://psas.revskills.de/?q=node/ and download the free version.
Run The program and select:
Menu-Hardware forensics-WINCE SD Utils and get your card serial number. (needs a windows mobile phone connected via activesync to the pc (with the card in it) to work though)'
Once you get the code, PM it to me and I will make a goldcard.img for you.
That way you can flash any rom without having hspl on the phone.
Again, this will only work with a card under 4gb. 1 or 2gb is recommended.
Andy

I cant beieve it, bricked phone?

Ever since I went to wp7 and back to android, my amazing hd2 has never been the same since. For weeks I have had freezing, so wanted to get a clean slate and start over. I did the following
Task29
Magldr 1.3
wanted to install nexushd2 so had to install
CWM_Recovery_for_NexusHD2_135M
it crashed towards the end of the install, ok I try to go back to magldr...but even tho I hold the button I dont get the options. I try it all again...same problem. I heard going back to stock 3.14 will fix most problems...it also hangs but at 8%?
Its now 6am and I need sleep...can anybody help...I really need a phone for tomorrow.
Thanks in advance
PS - Currently
PB81100 HX-BC
SPL-2.08.HSPL 8G EX
0X45
0X40
CotuallaHSPL
RUUNBH
Upgraed ROM code error, Please try again
Is that ok?

I got a quick question, did you reformat your SD card after you removed Windows Phone 7? If not this is probably your pro.lemons as WP7 cormates your card in a funky way so the phone tvinls the SD card is the enternal memory, I forget what it is called. But this is the same in WP7 native devices as they actually use SD card for memory and not enternal chips.
The best way to do this is to either vet an adapter and put your card in a digital camera and format it. Then reformat it again to Fat with your computer. Are you can just use your computer, but I suggest the digital camera as it will 100% remove the funky format.

Go into bootloader and flash a correct stock rom from USB. If it doesn't take confirm it's correct for your phone and try again.

sticking at 8% means a problem with installing the radio.
Put it in a plastic bag and pop it in the fridge for 30 minutes. remove and reflash.
I would recommend extracting the 3.14 installation file (using winrar).
Rename the RUU_signed.nbh to 'LEOIMG.nbh'.
Copy this file into the root of your SD Card, and pop the card in the phone.
Boot the phone whilst holding in the volume down button and let it flash.
If cooling the phone helped, send it back under warranty (you have got rid of HSPL, so all is good now.

I got mircosdhc to usb today, copied LEOIMG.NBH to sd, tried to flash but getting 28002 error not allowed
i then throws me back to spl 1.42
I have tried both 3.14 and 1.66 official roms...both sdflash and romupdateutility.
When I try sdflash with leoimg.nbg it gets to 1% then shuts down.
Is my hd2 dead? it doesnt even get orange led charge :-/
Tri colour screen now says
hx-bc
spl 1.42.0000 xe
micro (led) 0x05
microP(TOUCH) 0X40
Is that ok, I dont remember if being that

update
cant flash radios either, shows the progress bar then restarts.
I tried :
2.15.50.14
Gutted, its my best phone ever

hmm, quite a rash of stuck radios this past week or so, , hardware coming to the end of its flashable life?
@OP, some people are recommending (myself included it seems, by passing it on) chilling the phone in a sealed bag in fridge freezer, no sim no sd, then when its cool, put sd in and try to flash real quick, try a few times, keeping it sealed and cool.
Aparently the theory is that the hardware is overheating, and the cooling lets it work well enough for a little while.
There are one or two what look like success stories, it has to be said, but i wouldn't put a bet on it myself just yet.
Good luck.
(oh and i wouldnt put the phone in the bag in a warm room either, , take it outside for a while first, let it be cool before it goes in teh bag, less chance of condensation.)

It doesnt look good...either get a black screen with a triangle!
or if I get into the tri colour bootloader it says:
upgrade rom code error please try again
everytime i try flash a radio it goes either 0% or 8% reboots phone.
I wish I stayed on sd...never had any problems ever...ever since win7 my phone hasnt been the same.
Any more advice or links would be great, keep em coming. I dont want to give up on my hd2 just yet...Im mean its still (imo) one of the best android phones about

@ samsamuel
I cant flash via sd...keeps giving me
upgrade rom code error please try again
should i change my spl or something? its currently:
hx-bc
spl 1.42.0000 xe
micro (led) 0x05
microP(TOUCH) 0X40
do you know if that is ok?

this might be overstating an obvious that you've thought of, but are you sure you are using the correct stock ROM for your region? Have you tried flashing a custom ROM just to see what happens?

fracmo2000 said:
@ samsamuel
I cant flash via sd...keeps giving me
upgrade rom code error please try again
should i change my spl or something? its currently:
hx-bc
spl 1.42.0000 xe
micro (led) 0x05
microP(TOUCH) 0X40
do you know if that is ok?
Click to expand...
Click to collapse
flash back to hspl 3 and try again,if no succes ur bootloader is damaged and that will be problem

fracmo2000 said:
@ samsamuel
I cant flash via sd...keeps giving me
upgrade rom code error please try again
should i change my spl or something? its currently:
hx-bc
spl 1.42.0000 xe
micro (led) 0x05
microP(TOUCH) 0X40
do you know if that is ok?
Click to expand...
Click to collapse
that would be a stock spl then,, and with the rom update error, that means you have flashed the wrong stock rom from sd card. It has removed hspl, then the flash failed because you had (have) stock 1.42.0000 spl.
enter bootloader - usb - hspl4 - 2.08.hspl HSPL not 0000 - into bootloader again, has the spl changed? if not, then flashing is stuck, and you are in the stuck radio situation, if it HAS changed, now try flashing a rom or radio, , , flash from usb, see what happens.

orangekid said:
this might be overstating an obvious that you've thought of, but are you sure you are using the correct stock ROM for your region? Have you tried flashing a custom ROM just to see what happens?
Click to expand...
Click to collapse
not at all, keep me coming...I honestly dont see any other phone just now that I want (in the uk at least)...maybe the artrix but thats not for a few months...so need to get this baby back working!
I tried both 1.66 and 3.14 wwe (i couldnt see a uk one...
_HTC HD2_RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
Are they ok?

You could go to HTC's website, and search for HD2, and then go to downloads, and try downloading the newest rom that the site offers. You need to enter your serial number which is located under the battery. With some luck you will end up having a shipped rom, which has the same cid as your phone, and you will then be able to flash your phone via usb cable (from the tricolor screen).
If for some reason the HTC website won't accept your srial number, try to select another country from the top right part of the website.
I live in Serbia, and the Serbian HTC page has no rom downloads for HD2, the International page won't accept my serial, but the polish page did accept it. So keep trying, until the webpage accepts your sn.
If you are in no luck, you could try downloading roms from http://www.shipped-roms.com/.
Hope you will succeed in your quest to resurrect your phone.
Best of luck
d3m0n

d3m0n1 said:
You could go to HTC's website, and search for HD2, and then go to downloads, and try downloading the newest rom that the site offers. You need to enter your serial number which is located under the battery. With some luck you will end up having a shipped rom, which has the same cid as your phone, and you will then be able to flash your phone via usb cable (from the tricolor screen).
If for some reason the HTC website won't accept your srial number, try to select another country from the top right part of the website.
I live in Serbia, and the Serbian HTC page has no rom downloads for HD2, the International page won't accept my serial, but the polish page did accept it. So keep trying, until the webpage accepts your sn.
If you are in no luck, you could try downloading roms from http://www.shipped-roms.com/.
Hope you will succeed in your quest to resurrect your phone.
Best of luck
d3m0n
Click to expand...
Click to collapse
Ha, funny you should say mention that about HTCs site...but my S/N didnt work either. I wasnt sure if it was something to do with me/my phone or just the site was rubbish!
Im currently downloading an o2 rom frmo shippedroms (great site, thanks) so all my fingers and toes are crossed.
Funny thing is, I can flash hspl and hspl2, I managed to flash radio but not rom...keeps rebooting.

Did u take out sim and SD and try flashing?

@samsamuel
Well, I managed to get hspl4 on ok (2.08hspl) and then flashed a win6.5 rom it worked...but doesnt boot (stuck at flash screen)
When I downloaded official roms from both htc and shippedroms...they are corrupt. I used winrar, 7zip and tried to just run the packaged exe file...doesnt open.
Can anybody help me test these files and see if its me or have a good office rom they can upload?
@milli
when i managed to get an win6.5 rom flashed, sd was in, sim was out (i used hspl usb flash method)
EDIT - Found some o2 shipped roms on xda...extracted and going to try usb flash via hspl4

well i can flash radios and roms via hspl4 usb flash method AND usb via pc...but still cannot boot. Stuck at inital splash screen.
Any ideas now? We have made progress
edit - i have tried both custom roms and shipped o2 (uk) roms

Did you try hard reset after you'd flashed the rom(s)??

tried it once or twice, but not everytime. redownloading another rom
RUU_Le2_UK_1.43.206.4_Radio_Signed_15.26.50.07U_2.04.50.22_2_Ship_WORKING.exe (191,374 KB)
i hope this works...im getting desperate. Im still unsure at whats went wrong. Is it something wrong with my nand memory?
I can now flash radio, roms but yet cannot boot (Stuck at white htc splash...the red text sometimes appears...sometimes it doesnt).
edit - that rom failed to flash

[Q] HELP!!! I might have bricked this phone trying to flash a stock rom via SD

Hi all,
I would really appreciate if someone can help me reverse this process. I have an HD2 that i need to restore it back to factory ROM/condition and return it to US T-Mobile. I previously have WP7 on nand, Android on SD, Radio 2.15, with Mgldr 1.13 with HSPL 3.
I followed the procedure for flashing through SD as it will remove the HSPL. So i downloaded the ROM from TmoUS website, renamed the file to LEOIMG.nbh, and put it on a 4gb class 2 (FAT32) card. Enter bootloader mode by holding down volume/power button. Then it said loading and ask if I want to write over the image, select yes ... then it start the process. Though, half way through i receive the error message! Now when i turn the phone on i can't get past the bootloader mode. Just the error message even when I try to flash again via SD (the process doesnt even start - just said "loading" then "not allow" error message). When i get it plugged in to flash via desktop, the device is not recognized by the update utility. I'm not sure what could have gone wrong .. but any help or tips to reverse this process is greatly appreciated.
Thanks guys!!

What does it say in bootloader now?

If i just power it on I get the blank screen that said "error installing rom" with the triangle and the exclamation mark in the middle. If I boot into bootloader mode it will first get to the screen where it said "loading" then shortly it will say "error" and "not allow" then take me back to the bootloader mode. though, I noticed that the SPL is now 3.03 instead of 2.08 .. but other than that, I couldnt find a way to flash it by SD or USB. Any suggestion on this? Thanks for your help Macgnolia!

Sounds like it flashed the correct SPL and may be failing on the ROM flash, it sounds like it may be flashing the correct radio too.
What I would do is keep your phone completely off for about 3 hours, then turn it back on into bootloader, then try the flash again.
It might have some random overheat thing going on or something. Since you're back to stock SPL, go ahead and flash via RUU instead of SD and see if that does anything, it should let you since it's a stock ROM you're flashing.

Yeah I am with Orangekid here it might help to let your HD2 rest for a while so the internal temp is reduced as it my be some kind of freak heat issue right now. The HD2 hates heat incase you did not know this. I would still like to know what the top line of your bootloader says so we will know if you have the right device I.D. and that you are not one of the unlucky people to get a their device I.D. mysteriously screwed up by a stock ROM flash.

I'm at work and can't really play with it but definitely I will try it again jz to see if its the heat issue. Also, you think it could be the issue with the card by any chance? I was reading on flashing with SD and there were some conflicting opinions about the class and format for SD. And this is my wifes hd2 .. she'll probably freak out .. hehehe ... Thanks guys '-)
Sent from my HTC HD2 using XDA App

qdochemistry said:
I'm at work and can't really play with it but definitely I will try it again jz to see if its the heat issue. Also, you think it could be the issue with the card by any chance? I was reading on flashing with SD and there were some conflicting opinions about the class and format for SD. And this is my wifes hd2 .. she'll probably freak out .. hehehe ... Thanks guys '-)
Sent from my HTC HD2 using XDA App
Click to expand...
Click to collapse
card shouldn't matter as long as it's 8gb or less from my experience. Once it's off for a few hours just try to reflash stock via RUU and see what happens.
And yeah, go ahead and load up bootloader first to see what the top line says.

I just tested it again .. same problem! at the top right corner it says "RUUNBH" then the series of lines in the red portion of the screen as follows:
PB81120 SS-B3
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Upgrade ROM code error
Please try again
and if I just power it on it goes to the error message .. then "loading" screen .. then "error" .. then "not allow" .. then back to bootloader mode but the third line now say MicroP-Wrong Platform (0x0)
any suggestion guys??

I thought it might have been that the download rom was corrupted .. went to tmo and download another one .. I tried to flash again .. get from bootloader mode .. then to loading mode .. and just stuck there ..

qdochemistry said:
I thought it might have been that the download rom was corrupted .. went to tmo and download another one .. I tried to flash again .. get from bootloader mode .. then to loading mode .. and just stuck there ..
Click to expand...
Click to collapse
Have you try with different micro sd card?
battery pin check, whether it is bent.
Battery capacity should at least 50%
Did you rename the RUU_signed.nbh to leoimg.nbh?
When you transfer it to sd card, did you using card reader?
Anything is possible. Please take a look of the above check list

I'd be tempted to try a full change of spl, use hspl4 to drop spl from 3.03.0000 down to 2.08.0000 or 2.10.0000, then try first the 2.13 rom and then the 3.14 rom over USB again.

samsamuel said:
I'd be tempted to try a full change of spl, use hspl4 to drop spl from 3.03.0000 down to 2.08.0000 or 2.10.0000, then try first the 2.13 rom and then the 3.14 rom over USB again.
Click to expand...
Click to collapse
Done!! THANK YOU!!!!!
For some odd reasons, my laptop (win7 ultimate) always seems to have connection issues even with chevron for wp7. I plugged it in to my wife's laptop (vista ultimate) and it connects. I was reading your comment on a similar issue in another thread and along with your suggestion here .. I figured it must be HSPL issue. I first used HSPL4 to reinstall 2.08 and immediately mgldr popped up. Then i flash the Tmo stock ROM over it. Then use HSPL4 to flash over (twice) with 3.03 (the one without the HSPL).
It took away the Energy boot screen, now I'm on 3.14 with 2.15 radio. I checked bootloader and it saids the following:
PB81120 SS-B3
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Which is a problem because I checked on the refurbished device they sent and it has SPL 2.10. And so, I put HSPL 3.03 back on there to flash via SD again. Now i run into the same problem I orginally did .. about 20% into the update process and it stops and said update error. Could this be something obvious that I'm doing wrong? and also is there a way to get spl 2.10 without SD flash??
Thanks bud
Edit: I did it again a couple times via SD and it worked! I checked bootloader and it said spl 2.10 so I guess everything is back to stock now. I guess I'm gonna throw it back in the box and send it off. Thank you everyone for the fast reply and for all the help on this issue ... you guys are awesome! Thanks

[Q] Help! Spoiled hd2. Cannot do anything at all.

I have a 512mb hd2 and today, when i reboot my phone, magldr shows fatal hit 1 and it wont boot into android or enter cwm.
Therefore, i did a task29 and flashed a stock winmo rom using usb cable. However it wont boot into winmo. It shows the htc logo and it stucks there. Sometimes it show htc logo with rgb at the bottom and it will stuck there. I never get into winmo.
Then i tried flashing the stock winmo rom using the sd card method. However, when the phone say that the process is finished, i plugged out the battery. i didnt know that i have to press the red button.
Now, the phone will only boot into the tri coloured screen and the screen shows this:
e??????u HX-BC
(upside down "e" followed by some unknown and indescribable characters followed by a "u")
SPL-142.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
I cannot do anything else. I can't flash anything at all. It will end up in an error.
When i try to flash stock winmo rom using sd card, it will say loading... , then it will say checking... then this red numbers: 0058002 will appear on top then it will go back to the tri coloured screen again.
When can i do?

corrupted modelID, (the e??????u HX-BC bit)
I think JTAG is the only way out, and i've not actually seen hard confirmation that JTAG will fix it. there certainly isn't any flashing solution that i've seen, and we've seen this problem a fair few times.
Unlucky. Got warranty?

yes, its still under warranty. Would the warranty be void?

munchyzoo said:
yes, its still under warranty. Would the warranty be void?
Click to expand...
Click to collapse
Hi,
Unless you can flash an original WM ROM,warranty will be void.
You need to revert back to orginal... HSPL is a hack and your warranty is void.
Go to HTC site>support>download>ROM upgrade and choose appropriate ROM upgrade for your phone
Extract with winrar or 7z the RUU_Leo_HTC_****************************_Ship.exe
find the larger *.nbh file and rename it to leoimg.nbh and place this file on an sd card that is 4gb or less
and reboot to bootloader (the one with 4 colors,hold volume down button)
follow the instructions from there
That way you will have your original software with SPL restored and ready to send it for repair
No need for PC drivers etc.

Don't panic, faced this situation before.. create a goldcard .. follow this thread

Really? Goldcard ignores modelid? You sure? Cos that would imply that you could use a hd2 Goldcard to flash any winmo rom to any winmo phone, which you can't. I'll be interested in anyone confirming absolutely that a phone with a corrupted modelid in bootloader can be flashed from Goldcard.
@op. Yes warranty is valid If your boooader shows a valid spl, ending 0000,because you tell them you woke up and it was on the charger, hot, and in bootloader, screen on, that top line looks wrong, you tried to flash the stock rom but it fails. So long as the spl is good is usually enough for warranty.

Yes with goldcard you can put any HD2 rom on any HD2 phone, debrand .. make it chinese or whatever.

And that's my slightly sarcastic point,,,,, if the modelid is corrupt the Goldcard won't recognise it as a hd2.

munchyzoo said:
Now, the phone will only boot into the tri coloured screen and the screen shows this:
e??????u HX-BC
(upside down "e" followed by some unknown and indescribable characters followed by a "u")
SPL-142.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
When can i do?
Click to expand...
Click to collapse
I saw on the bottom Mr Samsamuel is here, he point me a lot of help to revive my HD two days ago, now my hd2 is up and running. First you failed with MAGLDR, and you did to revive with stock rom. what stock rom did u use. More info will help many hd2 guru here
I believed before you flash anything (as I understood from own experience) flash HSPL, do task29, flash Radio. Just try and let us know. alert : do not do this on Virtual Machine
I have step by step edited copy tutorial to install cLK on hd2, it also can be use to revive brick hd2 (at some level of brick) PM me I will send by email
let us have coffee

the stock rom I use is hTC_Asia_WWE_1.66.707.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
but the problem is I can't do anything with my phone at all. i can't flash hspl or any rom at all...
Buy anyways i have gotten my phone back from htc and now its working. i am now afraid of installing magldr as i fear the same problem (fatal hit 1) will happen again.
I am now considering the old sd card method of running android.... (i think this is safer)
Not sure if clk would have a similar error or something... i have not try it before.
I have googled the magldr fatal hit 1 error and quite a few people have this problem but i can't seem to find a real solution to it. I remember reading somewhere that someone say it is caused by many bad blocks on nand due to excessive flashing. (not sure what this means and how to deal with it)

Since got back ur live hd2. It will no fun anymore. No singgle software 100% safe or bug free. Clk is almost same with MAG both are boatloader. Your bootloader from htc also not bug free.
Running os from sd card is slow. Its same as ur pc booting from live cd/usbstick or external hdd. That for emergency only, rescuing fail software etc. Just do everything carefully read all instruction asking forum and google. You will safe and have a lot of fun
Sent from my HTC Incredible S using XDA App

[Q] HELP ASAP!!! Software Update Failed and won't read SD Card:(((:((

Before I succesfully flashed Custom Windows Rom and had Android in my SD card root folder. I also flashed HSPL and MAGLDR113 and CWM Recovery v3.2 trying to install Nexus. But I couldn't copy the Nexus...rar file cause I didn't locate the file on the computer.
So I decided to flash back to original ROM for my HD2.
I copied LEOIMG.nbh to SD card but then it said "File cannot be located" so basically it partially copied and when I rebooted my phone and it showed white screen with a message of an update. I cancelled update but nothing happened it just came back to the same message and tried to update software but it failed.
So now I stuck in tri-color bootloader with a message:
SS-B3
SPL-2.10.0000 8G XE
MicroP(LED) 0x05
MicroP(Touch) 0x40
I doesn't even read the card any more so I CANT DO ANYTHING!!
What's weird too when I checked SPL version it was 2.08 but now it's 2.10.
WTF is going on? Can anybody tell me? Is it fixable at all?(((

Ok this is what I would do, I would back up my SD card on my computer. Then I would do a full reformat of my SD card with Fat 32. then re download the Windows Mobile stock ROM for your HD2 and copy it to the re formatted SD card. I would only have the ROM on my SD card and then put it in my HD2 and boot it up into bootloader.
The ROM you tried to flash is what changed your SPL to 2.10.0000. Cause the SPL flashes before the ROM does. So that means it was something wrong with the ROM and it could not flash it.

Yeeeeaaaaayyyy!
I fixed it, man!
What I've missed is to launch bootloader pressing down button, then it showed USB mode at the bottom, after that I could flash stock ROM to my HD2!!!
Now it's all good.
The only thing I wonder now: what HSPL should I flash?
Is HSPL 2.08 still ok?

zandulya said:
I fixed it, man!
What I've missed is to launch bootloader pressing down button, then it showed USB mode at the bottom, after that I could flash stock ROM to my HD2!!!
Now it's all good.
The only thing I wonder now: what HSPL should I flash?
Is HSPL 2.08 still ok?[/QUOTE
You must have flashed a official update for your HD2 so I would say yes cause you are still on official stock software. But I still suggest you do a little double checking to see that the ROM you have is a ROm that was released for your specific HD2.
Click to expand...
Click to collapse

Thanks!!
Yep, I don't remember what link I used but I put in my IMEI so it referred me to a particular rom!
Back on track now testing some new ROMs.
Do u have any suggestions for Android ROMs?

Hello to you all,
I have some sort of the same problem. First my original windows 6.5 did not start up any more. That made me look on the internet to see what options there where to fix it. After finding a lot of options I choosed to install android on my system. That worked for a long time but unfortunately it also hung itself up. As a reaction I tried a hard reset and it looks like that was fatal for my phone because I cannot install anything anymore. The only thing I can come in is bootloader menu but when I want to install anything, it stops before finishing.
Is there someone who can help me with this problem? By forehand thanks!
Kind regards,
Jaimy