Does anyone know information about how to connect the Samsung Fascinate as Diag Mode driver? ie: this type of connection needed for QPST/QXDM/CDMA Workshop.
I tried 'debugging mode' enabled from the settings in the Applications, but it didn't create any new port that would recognize for my phone.
The Epic solution is pretty strait forward
Install USB Drivers:
32 Bit or 64 Bit
Put phone into DIAG mode:
Dial ##8778#
Select UART = Modem, USB = Modem.
Click to expand...
Click to collapse
This doesn't seem to work on Fascinate though.
Go to Settings - Wireless Networks - Click to Dialup Networking this will also put it in Dialup mode
hetaldp said:
Go to Settings - Wireless Networks - Click to Dialup Networking this will also put it in Dialup mode
Click to expand...
Click to collapse
wow man, thanks a lot that worked.
Remember to put it Again Dialup Networking off
Thank you for the steps. I was also able to get the phone to be read by QPST and CDMA Workshop. The odd thing is that when I tried to read the phone again the next day, none of the software will read the phone. Interestingly, I can see the COM port and the Modem port in the Device Manager, but the software refuses to read the phone. I am wondering if I accidentally changed one of the settings to turn it into UART or something to this effect, but the code that I found for this (##UPST#) does not work on the phone, even with hidden menu enabled. Any suggestions, currently I am stuck with a phone that can only do voice and text, no 3G? Thank you in advance!
You could try Diag mode
Diag/Testing Mode
*#4636*1111#
QPST sees it, but nothing is editable, in Dial-Up mode?
Thank you for your response! I tried that, it took me to the menu, plugged the phone to the PC, Device Manager shows Samsung Diagnostic Port, I use CDMA Workshop to try to at least read the phone. I connect to the correct COM port, but CDMAWS fails in reading it. I don't get it, it used to work fine with almost the exact same setup. I uninstalled the drivers, reinstalled them, same thing. Wiped the phone, same thing. Kind of frustrating. The only resort I have now is to maybe just get it fully flashed to stock so that I can start from scratch again. Odd, I have never had a phone that was giving me a COM port that phone software consistently fails to read, especially when it worked before. lol. Any assistance with anything else I may try would be greatly appreciated.
**usbui select Modem.. and
Bringing this issue up.... I cannot get it to work. I've read tons of threads and everyone says go to Device Manager and click Ports and then change the port on the Samsung to port 1 and it will show up blah blah Blah.... there is no list that says "Ports" in Device Manager. I have this DialUpNetworking thing checked and debug mode and the port1 shows up in QPST but it says "No Phone". And yes all drivers are installed.
Diag/Testing Mode
*#4636*1111# ??????
That doesn't do jack. It just lets me input the numbers and when I press the last #, all the numbers vanish. I need this to work or I have to get a different Phone.
nFiniti said:
Bringing this issue up.... I cannot get it to work. I've read tons of threads and everyone says go to Device Manager and click Ports and then change the port on the Samsung to port 1 and it will show up blah blah Blah.... there is no list that says "Ports" in Device Manager. I have this DialUpNetworking thing checked and debug mode and the port1 shows up in QPST but it says "No Phone". And yes all drivers are installed.
Diag/Testing Mode
*#4636*1111# ??????
That doesn't do jack. It just lets me input the numbers and when I press the last #, all the numbers vanish. I need this to work or I have to get a different Phone.
Click to expand...
Click to collapse
Do a search in general...i posted how there. It's like *33 something.
**33284 is what ur looking for
Edit: you need to set up the com. That requires knowing the port and putting the phone into dial up mode.
TRY **USBUI (**87284)
You can switch the UART and USB from PDA to MODEM here.
denonlake said:
TRY **USBUI (**87284)
You can switch the UART and USB from PDA to MODEM here.
Click to expand...
Click to collapse
No, I know exactly what he's doing. The phone needs to be in network dial up mode. But for qpst to reckognize it, he needs to add the com.
I found that only the .323 version of qpst worked for me. Also there is the *229 (i think) will reprogram those settings you may have messed up, maybe try that?
Sent from my rooted froyo Fascinate
ziggy484 said:
I found that only the .323 version of qpst worked for me. Also there is the *229 (i think) will reprogram those settings you may have messed up, maybe try that?
Sent from my rooted froyo Fascinate
Click to expand...
Click to collapse
323 works for basic flash, however if he's trying to get ppp configs setup for 3g and what not, he will need build 215. 323 will always revert to the original settings. If he's just trying to flash the prl, then it's no big deal. If he's trying to flash over to a different carrier, then it'll revert to vrz settings.
Menu > Settings > Wireless & Networks
Enable Dial up Networking
Next..
Menu > Settings > Applications > Development
Enable USB Debugging
-------------------------------------------
If Dial-up Networking is not showing perform the following. Dial **33284 followed by SPC (000000 or 468346 ) then scroll to Port Map and select HFK,DIAG. Once this is complete, you should now have Dial-up Networking showing up under Wireless and Network.
Bypass Activation:
Press "Emergency Call"
Dial *#83786633 then press send
After you press "send" press the "home" key and you should now be passed activation
this worked in getting the fascinate into daig mode. thank you!!!
JUSMEJOSE said:
Menu > Settings > Wireless & Networks
Enable Dial up Networking
Next..
Menu > Settings > Applications > Development
Enable USB Debugging
-------------------------------------------
If Dial-up Networking is not showing perform the following. Dial **33284 followed by SPC (000000 or 468346 ) then scroll to Port Map and select HFK,DIAG. Once this is complete, you should now have Dial-up Networking showing up under Wireless and Network.
Bypass Activation:
Press "Emergency Call"
Dial *#83786633 then press send
After you press "send" press the "home" key and you should now be passed activation
Click to expand...
Click to collapse
pkopalek said:
You could try Diag mode
Diag/Testing Mode
*#4636*1111#
QPST sees it, but nothing is editable, in Dial-Up mode?
Click to expand...
Click to collapse
thanks dude your really great i'll bet you make your company lotta money
i need the 16 digit password to change the serial number in sansung galaxy s i400
hello
i need the 16 digit password to change the serial number in sansung galaxy s i400 in cdma works shop please
---------- Post added at 06:18 PM ---------- Previous post was at 06:09 PM ----------
denonlake said:
TRY **USBUI (**87284)
You can switch the UART and USB from PDA to MODEM here.
Click to expand...
Click to collapse
i need the 16 digit password to change the serial number in sansung galaxy s i400 to cdma works shop please
JOSEUBIERA said:
hello
i need the 16 digit password to change the serial number in sansung galaxy s i400 in cdma works shop please
---------- Post added at 06:18 PM ---------- Previous post was at 06:09 PM ----------
i need the 16 digit password to change the serial number in sansung galaxy s i400 to cdma works shop please
Click to expand...
Click to collapse
A quick interweb search brought up this number for the Samsung Continuum SCH-I400
20 10 03 16 19 81 02 19
.
Related
I have a VX6900 that was Flashed to Cricket, I have GPSViewer, Google maps, HTC GPS tool, & Quick GPS. each one see that i have a GPS card but I have never gotten a lock on, I have followed many treads, but I still can't get the GPS to work on my phone. please Help
try gps toggle
my sister flashed her sprint version of the touch to cricket and she uses gps toggle to turn on/off the gps receiver. i suggest that you only have google maps and gps toggle installed, and nothing else. give it a try and let me know if it worked out for you!
good luck
I've been told that nothing i do will enable my GPS because it was flashed wrong
wakko69 said:
I have a VX6900 that was Flashed to Cricket, I have GPSViewer, Google maps, HTC GPS tool, & Quick GPS. each one see that i have a GPS card but I have never gotten a lock on, I have followed many treads, but I still can't get the GPS to work on my phone. please Help
Click to expand...
Click to collapse
I also have mine flashed to Cricket. I have never got a GPS lock on mine...
So anyone have any ideas??
did you get GPS working
Did you get GPS working with your cricket ROM If not let me know I can help you.
Please post anyway how to get GPS working with a Cricket ROM.. Also, do you or does anyone have suggestions for a Cricket ROM having just a stock Sprint Touch? Thanks in advance.
phigan said:
Please post anyway how to get GPS working with a Cricket ROM.. Also, do you or does anyone have suggestions for a Cricket ROM having just a stock Sprint Touch? Thanks in advance.
Click to expand...
Click to collapse
I will post you a nice tutorial tomorrow for the GPS and if you PM or post your email I will send you one of my cricket custom ROMS for the touch.
cricket ROM and tutorial
I have included a custom ROM in this tutorial
1st off credit is due to those that wrote these programs I only take credit for putting this all together.
#1 use msl grabber to get the msl/spc code found here
http://forum.ppcgeeks.com/showthread.php?t=43560
install via activesync or sd card and run on ppc.
#2 unlock with the 2.31 unlocker listed here
http://forum.ppcgeeks.com/showthread.php?t=20370
#3 flash this sprint 6.1 ROM to update radio "WARNING DO NOT LET CUSTOMIZATION RUN" SOFT RESET WHEN IT SAYS AUTO CUSTUMIZATION IN 3 SECONDS. This is for GPS1 to work.
http://www.htc.com/us/SupportDownloa...cat=2&dl_id=66
To do this connect USB to computer then Press power camera and Reset to get to bootloader red green yellow screen and connect to cable then run the exe file. DO NOT LET CUSTOMIZATION RUN SOFT RESET WHEN IT SAYS CUSTOMIZE IN 3 SECONDS.
#4 Go to the following and download from windows drivers and unlocking tools
http://www.4shared.com/dir/13898363/...4/sharing.html
QPST
windows htc driver
activesync4.5
Ryanmogul diagnostics shortcuts
download the following
http://www.4shared.com/file/10597370...HMregedit.html
http://www.4shared.com/file/94425441...t5_0_31_7.html
Install Ryans diagnostics on ppc
Install QPST on computer
Install htc drivers on computer
Put phone into diag mode & connect to computer. computer should connect and find new device
run QPST configururation and add new port till you find your phone.
Now in QPST run from top menu start clients service programing.
Select phone
Read from phone imput spc/msl code from the grabber.
Then enter 000000 in the service programing field.
Write to phone
now while in QPST lets get your GPSone ste up for cricket.
Go to the GPS1 tab and uncheck all the boxes then recheck them.
then enter the following
pde ip address 117.29.223.11
pde port # 8080
pde transport IP
Position calculation mobile
Write to phone
close out
I would recommend now to flash a custom ROM here is a link to one of mine. http://www.4shared.com/file/135174580/27254c16/VOGUIMG.htmlinstall on a FAT32 formated 2gig or less msd card and rename to VOGUIMG.NBH THEN INSERT CARD AND PUT PHONE INTO BOOT LOADER AND FOLLOW INSTRUCTIONS.
You will need a cricket PRL to load through PST setting.
then go to this thread it will help you set up your pst setting correctly.
http://forum.xda-developers.com/showthread.php?t=492824 *NOTE* In some cricket markets you will need to change from EVRC to VOICE 13K to make outgoing calls. YOU CAN ALSO DOWNLOAD THE MMS CAB FROM HERE and then
Install the cricketwapmms cab
Do not try to open a data connection untill you have cricket service on the phone.
To authinticate your user name 10digit#@mycricket.com
you must have service.
Just a couple notes to have Email and push services work you MUST have the $15.00 HTML plan on your account and your phone must be listed in the system as a QA4 Evoke.
GPS may Require priming unless you use Ryans Googlemaps.cab
Credits go to ImCokeMaN for the unlocker and his great tutorial
and Ryanmogul6800 on XDA for his great software and his perfect PST setting.
Please let me know if this helped any or if I can be of any further assistance.
__________________
My GPS is working, But I had help there a guy in omaha that did it and it's running nice.
Good glad you got it running Also if you wanted push email to work there is a program called funambol that works ok with cricket.
hi i am tryin to get the gps running using your fix but all of the links are not working when i click on them but just to tell you what im working with i have the sprint vogue flashed to cricket and im running the new nsfan wm6.5 v16 rom and when i try gps viewer i cant find a fix, so is it the rom maybe cause my radio is 3.42.50....so can you point me in the right direction cause my phone is amazing but the gps is a setback and this is something that i really want spent weeks looking for something so thanks for all of your help
I apologize for that I don't know why they don't work here is the GPS1 setting that need to be entered in QPST. Your radio version is good to go for GPS.
while in QPST lets get your GPSone ste up for cricket.
Go to the GPS1 tab and uncheck all the boxes then recheck them.
then enter the following
pde ip address 117.29.223.11
pde port # 8080
pde transport IP
Position calculation mobile
Write to phone
It looks like you have a good rom to be using so most of the links you don't really need.
Links you may need are below and they do work I just checked.
QPST http://www.4shared.com/file/101893747/6958b637/QPST_v27_Build_301.html
HTC driver http://www.4shared.com/file/101893703/a59b72a/WindowsHTCdrivers.html
Diagnostics shortcuts http://www.4shared.com/file/101893721/d661b484/RyanMogul_Diagnostic_Program_Shortcuts.html
thanks so much u will try it now and get back to you
Please help ASAP PLEASE!
RE:QPST wont recgonize my intercept! ntohing comes up when i try to add new po
Your computer has to see the phone as a modem instead of a usb disk. Dial ##8778# and it should bring up a menu that allows you to change these settings. You can see which port the phone is registered under in device mgr. under COM and then input it manually, or you can have QPST find it if you uncheck the option to only look for serial ports on the add new port popup menu. Not sure if this works with Virgin Mobile rom.
I just downloaded the driver for my Intercept and it slved te problem. You can get it on the Samsung website then go to "Support" then just find your device and download the driver.
Sent from my SPH-M910 using XDA App
flashing sprint intercept to cricket
hey everybody, ive been flashing OG droids to cricket for a while and this is the first time ive tried to flash this phone(sprint intercept). jw if anybody has a write up on it or anything,, i flashed the cricket prl to it but when i dial *611 it says "there is a problem with ur account please contact cricket" any help would be greatly appreciated! thanks in advance
alright, So on my GSM HTC 8x (T-Mobile), I got File Explorer working in QPST. I can read and write various NVram values, change band prefs, etc. One thing interesting I found in the File Explorer (Not Windows OS, but for the Fileexp for the modem) is there is a directory called "Supl". In it is a file called "SuplRootCert". I copied it to my PC, and renamed it to "SuplRootCert.cer". When I opened the file, it presented itself as the "T-Mobile USA Root CA". Trusted Root Certificate.
I wonder what this is doing here? It can't be for Wi-Fi calling because the firmware doesn't support it (although it did at one time)..I wonder if we can put our own root certificate here and if the phone will trust it?
compu829 said:
alright, So on my GSM HTC 8x (T-Mobile), I got File Explorer working in QPST. I can read and write various NVram values, change band prefs, etc. One thing interesting I found in the File Explorer (Not Windows OS, but for the Fileexp for the modem) is there is a directory called "Supl". In it is a file called "SuplRootCert". I copied it to my PC, and renamed it to "SuplRootCert.cer". When I opened the file, it presented itself as the "T-Mobile USA Root CA". Trusted Root Certificate.
I wonder what this is doing here? It can't be for Wi-Fi calling because the firmware doesn't support it (although it did at one time)..I wonder if we can put our own root certificate here and if the phone will trust it?
Click to expand...
Click to collapse
The name of the certificate reminds me something about A-GPS, but I could be wrong....
But there is something very intriguing in your experiments: perhaps that way we could enable LTE on the international ATIV S.
Topogigi said:
The name of the certificate reminds me something about A-GPS, but I could be wrong....
But there is something very intriguing in your experiments: perhaps that way we could enable LTE on the international ATIV S.
Click to expand...
Click to collapse
I have something you ca try with your Ativ S, if you want:
Try installing the diagnosticApp_Sprint onto your Ativ via the Microsoft Store (Set OEMID to HTC and CID to "null") Then see if you can toast your way to app://e69a2877-59b8-43ed-898d-554fbc4b8b2b/_default#/EmbeddedTool;component/DMSwitchPage.xaml Once there, you can try toggling one of the switches (both will enable the necessary serial Port). When the phone auto-reboots, you should be able to connect it to the PC. Once Windows Update finds and installs the drivers (I am assuming it will do this for the ATIV S), launch the "QPST Service Programming tool" (QPST can be found on the forum if you search for it) Once that tool loads, pick out your device and click "connect". Once that loads, click "read from phone". now go to the UMTS System tab to set your band preferences. (My 8x had all of them enabled by default) (I have nothing to compare it to, so YMMV). Once you have made changes, just press "write to phone" and wait for it to reset. Hopefully then you will have LTE enabled!
compu829 said:
I have something you ca try with your Ativ S, if you want:
Try installing the diagnosticApp_Sprint onto your Ativ via the Microsoft Store (Set OEMID to HTC and CID to "null") Then see if you can toast your way to app://e69a2877-59b8-43ed-898d-554fbc4b8b2b/_default#/EmbeddedTool;component/DMSwitchPage.xaml Once there, you can try toggling one of the switches (both will enable the necessary serial Port). When the phone auto-reboots, you should be able to connect it to the PC. Once Windows Update finds and installs the drivers (I am assuming it will do this for the ATIV S), launch the "QPST Service Programming tool" (QPST can be found on the forum if you search for it) Once that tool loads, pick out your device and click "connect". Once that loads, click "read from phone". now go to the UMTS System tab to set your band preferences. (My 8x had all of them enabled by default) (I have nothing to compare it to, so YMMV). Once you have made changes, just press "write to phone" and wait for it to reset. Hopefully then you will have LTE enabled!
Click to expand...
Click to collapse
You can do this with samsung diagnosis, open it and enter *#7284#, then select QC RmNetComposite. After doing whatever you want, you can go back setting it to MTP again.
The phone will reboot when you change this value.
greenboxal said:
You can do this with samsung diagnosis, open it and enter *#7284#, then select QC RmNetComposite. After doing whatever you want, you can go back setting it to MTP again.
The phone will reboot when you change this value.
Click to expand...
Click to collapse
Obviously, the new version of the diagnosis app (the one included in the official GDR3 update) inhibits that code...I think I will decide myself to restart from GDR2 and upgrade with the "polish" hack, in the end. I was too lazy to do it, Now I have at least a good reason to do it....
compu829 said:
alright, So on my GSM HTC 8x (T-Mobile), I got File Explorer working in QPST. I can read and write various NVram values, change band prefs, etc. One thing interesting I found in the File Explorer (Not Windows OS, but for the Fileexp for the modem) is there is a directory called "Supl". In it is a file called "SuplRootCert". I copied it to my PC, and renamed it to "SuplRootCert.cer". When I opened the file, it presented itself as the "T-Mobile USA Root CA". Trusted Root Certificate.
I wonder what this is doing here? It can't be for Wi-Fi calling because the firmware doesn't support it (although it did at one time)..I wonder if we can put our own root certificate here and if the phone will trust it?
Click to expand...
Click to collapse
How did you do that? I mean... I have a GSM HTC 8x as well and I'd like to edit the registry (mainly to change roaming preferences, bands preferences and if it is possible, the accent colors). Is that possible?
I have installed the Sprint Diagnostics app but it only shows the IMEI info and the SIM card info, nothing more. It does absolutely nothing else. Am I missing something?
You need to install @cpuguy's Native Toast Launcher
and paste this inside the box.
app://e69a2877-59b8-43ed-898d-554fbc4b8b2b/_default#/EmbeddedTool;component/DMSwitchPage.xaml
Click to expand...
Click to collapse
cybermiguel said:
How did you do that? I mean... I have a GSM HTC 8x as well and I'd like to edit the registry (mainly to change roaming preferences, bands preferences and if it is possible, the accent colors). Is that possible?
I have installed the Sprint Diagnostics app but it only shows the IMEI info and the SIM card info, nothing more. It does absolutely nothing else. Am I missing something?
Click to expand...
Click to collapse
this only allows you to edit the phone modem at this time. We might be able to reflash the os partition with this.
compu829 said:
this only allows you to edit the phone modem at this time. We might be able to reflash the os partition with this.
Click to expand...
Click to collapse
Oh well, no problem with that. I'd like to know if I can enable the AWS band on my phone (I got the c620e version). By the way, working with the modem, can I set some MCCs to be recognised as "home" network? Because I use a MVO and the whole time it says it is roaming (when it actually isn't).
compu829 said:
this only allows you to edit the phone modem at this time. We might be able to reflash the os partition with this.
Click to expand...
Click to collapse
I tried your method but the tool is unable to write to the phone. Keeps getting a "phone stopped responding to memory" error
compu829 said:
I have something you ca try with your Ativ S, if you want:
Try installing the diagnosticApp_Sprint onto your Ativ via the Microsoft Store (Set OEMID to HTC and CID to "null") Then see if you can toast your way to app://e69a2877-59b8-43ed-898d-554fbc4b8b2b/_default#/EmbeddedTool;component/DMSwitchPage.xaml Once there, you can try toggling one of the switches (both will enable the necessary serial Port). When the phone auto-reboots, you should be able to connect it to the PC. Once Windows Update finds and installs the drivers (I am assuming it will do this for the ATIV S), launch the "QPST Service Programming tool" (QPST can be found on the forum if you search for it) Once that tool loads, pick out your device and click "connect". Once that loads, click "read from phone". now go to the UMTS System tab to set your band preferences. (My 8x had all of them enabled by default) (I have nothing to compare it to, so YMMV). Once you have made changes, just press "write to phone" and wait for it to reset. Hopefully then you will have LTE enabled!
Click to expand...
Click to collapse
I did all of that on my HTC 8x (model c620e) and it did work. However, I'm kind of stuck because Windows doesn't detect the appropriate drivers for the phone and all I got is "HTC Composite device". Do you have any driver that I can use?
@cybermiguel It did that to me at first, too. Make sure the PC you are using has Internet, right-click on the "HTC composite device" in device manager, select "update driver software". Then tell it to search automatically for drivers. They will "magically" appear.
AlvinPhilemon said:
I tried your method but the tool is unable to write to the phone. Keeps getting a "phone stopped responding to memory" error
Click to expand...
Click to collapse
weird. I was using QPST 2.7 Build 402, and it was working fine. I was able to use "EFS Explorer" and "Service Programming" to read/write various info. Try a different USB cable or port on your computer?
Try this driver, for me work (disable driver signature)
My options for Ativ S LTE support
Here my options (ativ S)
What i enable for LTE support?
Mattemoller90 said:
Here my options (ativ S)
What i enable for LTE support?
Click to expand...
Click to collapse
keep going...there is a tab all the way over to the right that will deal with LTE.
compu829 said:
keep going...there is a tab all the way over to the right that will deal with LTE.
Click to expand...
Click to collapse
Find!! This is my "LTE tab"
If you have a phone with LTE enable I can try to set my "LTE tab" as yours
It's dangerous for my phone?
Mattemoller90 said:
Find!! This is my "LTE tab"
If you have a phone with LTE enable I can try to set my "LTE tab" as yours
It's dangerous for my phone?
Click to expand...
Click to collapse
Who knows...
Anyone know how can we connect Lumia 920 over QPST ?
it can't detect my Phone
Mattemoller90 said:
Find!! This is my "LTE tab"
If you have a phone with LTE enable I can try to set my "LTE tab" as yours
It's dangerous for my phone?
Click to expand...
Click to collapse
The screenshot you posted seems to me unuseful: all is already enabled and activated. Can you please post a screenshot of the NAS tab? There you should find if LTE UE OP classes are enabled, and, first of all, if UE RAT includes LTE or not.
1 .restore your original partition
2 .update with official 2.3.5(some phone will be lost imei)
3 .dial *#*#2846579#*#*
4 .background settings- qualcomm background settings-open-password 0 confirm
5 .usb port settings manufactor mode , and restart the phone
6 .turn on usb debugging and connect to pc
7 .run DFS , select port db adapter (downloadfrom attached files)
8 .click on spc
9 .click on pragramming tab
10.if you lost your imei type and write imei(check attached files)
11.check your current wifi-mac address
12.and type it in the mac address box
13.write after successfull close and reopen the dfs and connect again
14.click on read button (nearly to mac address)
15.mac address will show automatically
16. now root and flash any rom wifi will work :good:
thanks for your help:good:
with this new DFS-tool{old one 3.3 cannot restore mac} i managed to restore my mac address and also the serial number!:highfive:
RajuMon said:
1 .restore your original partition
2 .update with official 2.3.5(some phone will be lost imei)
3 .dial *#*#2846579#*#*
4 .background settings- qualcomm background settings-open-password 0 confirm
5 .usb port settings manufactor mode , and restart the phone
6 .turn on usb debugging and connect to pc
7 .run DFS , select port db adapter (downloadfrom attached files)
8 .click on spc
9 .click on pragramming tab
10.if you lost your imei type and write imei(check attached files)
11.check your current wifi-mac address
12.and type it in the mac address box
13.write after successfull close and reopen the dfs and connect again
14.click on read button (nearly to mac address)
15.mac address will show automatically
16. now root and flash any rom wifi will work :good:
Click to expand...
Click to collapse
Didn't work for me. Actually there is no field for mac address change. Please help me...
check
avi062 said:
Didn't work for me. Actually there is no field for mac address change. Please help me...
Click to expand...
Click to collapse
can you connect the phone to dfs tool
Not working with ICS AuroraSP
There is no background setting in ICS AuroraSP.
So after dialing *#*#2846579#*#* nothing happens.
its only on official GB .update your Phone with official update
download link here(http://consumer.huawei.com/en/support/products/downloads/detail/u8800-en.htm?id=13396)
Sorry but this cdma tool is 3.1 and there is no mac adress field... can you send me the 3.3 or somehting?
nick#18 said:
Sorry but this cdma tool is 3.1 and there is no mac adress field... can you send me the 3.3 or somehting?
Click to expand...
Click to collapse
I have to confirm: the attached file brings a tool 3.1 - no MAC option for my device...
android_paul said:
I have to confirm: the attached file brings a tool 3.1 - no MAC option for my device...
Click to expand...
Click to collapse
The demo version from here should do the trick too (worked on U8860).
http://cdmatool.com/download
Blefish said:
The demo version from here should do the trick too (worked on U8860).
http://cdmatool.com/download
Click to expand...
Click to collapse
Hi
Tried both DFS.exe and DFS demo. I can see the updated IMEI on the device but the phone still doesn't show updated wifi
any suggestions
Thanks for helping on the IMEI part
mohammad.nomaan said:
Hi
Tried both DFS.exe and DFS demo. I can see the updated IMEI on the device but the phone still doesn't show updated wifi
any suggestions
Thanks for helping on the IMEI part
Click to expand...
Click to collapse
Try switching the OTP NV filters on/off etc. I had similar issue on U8860 and somehow I was able to write all the info back eventually. I don't remember what I specifically changed though. Great to know IMEI is back though!
Blefish said:
Try switching the OTP NV filters on/off etc. I had similar issue on U8860 and somehow I was able to write all the info back eventually. I don't remember what I specifically changed though. Great to know IMEI is back though!
Click to expand...
Click to collapse
Thanks Blefish,
The IMEI is back as I wanted
I tried that option as well. As you can see on the screenshot, I see the WiFi keys in the application as before but the same does not show on my device.
Tried both OTP NV Enable & Disable but still the same result.
If you recommend, ill flash the official update again if that can bring back the wifi keys or else ill leave it as it coz your Ideos Setting app does have that option and you I hope we will have it in CM12 as well
EDIT
DFS Demo helped in ficing WiFi keys. NV option helps as Blefish pointed out
Now all if fine - IMEI & WIFI
thanks a lot for your help and assistance
Blefish said:
Try switching the OTP NV filters on/off etc. I had similar issue on U8860 and somehow I was able to write all the info back eventually. I don't remember what I specifically changed though. Great to know IMEI is back though!
Click to expand...
Click to collapse
Hi Blefish, I would like to know if your SN is correct (in settings) after using DFS.
On my Honor I have everyting OK only when I restore it via 5iromtoolbox, but I cant flash any rom except B939 after that :crying:
I wonder if you have SN the same as MAC in settings, too
JekaPinsk said:
Hi Blefish, I would like to know if your SN is correct (in settings) after using DFS.
On my Honor I have everyting OK only when I restore it via 5iromtoolbox, but I cant flash any rom except B939 after that :crying:
I wonder if you have SN the same as MAC in settings, too
Click to expand...
Click to collapse
In my U8800 everything is ok, however, U8860 had zero imei and zero BT/MAC address (which was set to a random one). The serial number shown in the projectmenu tool (Huawei firmware stock) shows correct serial number (the 16 digit one, same as on the phone behind the battery).
In U8800pro/U8860 ICS release, Huawei is using the Settings->Status serial number same as MAC address. If the serial number shows unknown, MAC addresses are incorrect too.
Blefish said:
In U8800pro/U8860 ICS release, Huawei is using the Settings->Status serial number same as MAC address. If the serial number shows unknown, MAC addresses are incorrect too.
Click to expand...
Click to collapse
On B919 my MAC was ok bun SN was unknown
JekaPinsk said:
On B919 my MAC was ok bun SN was unknown
Click to expand...
Click to collapse
BT MAC aswell? I don't remember which one it used.
Blefish said:
BT MAC aswell? I don't remember which one it used.
Click to expand...
Click to collapse
Yes. Until I made changes to BT MAC it showed nothing, but now I have it working.
PS: Why new branches?
JekaPinsk said:
Yes. Until I made changes to BT MAC it showed nothing, but now I have it working.
PS: Why new branches?
Click to expand...
Click to collapse
For TWRP (and maybe more) .
Hello guys,
my U8800-51 is on the latest LegacyHuawei CyanogenMod 11.0 by Mr Blefish but i ended up without no WIFI MAC and BLuetooth. So i tried as stated on this post to downgrade to android 2.3 but when it gets to part 2/2 of the installation, gives me an error... Then, i proceeded to use DFS v14 to try to write the MAC adress (still on CyanogenMod) but it failed to find the COM PORT through PC (ADB install correct and showing the device, USB debuggin enable). The only way i managed to see the port in the device manager and DFS is tu putting the phone on the PINK SCREEN (Download mode, right?). but, DFS throw me some errors like CPS_BPSR and so on.
I also tried enabling DIAG port through ADB but didn't work.
So far, it has failed... But maybe you can help me.
I understand this is a very old phone, but i live in a 3rd world country where phones are ver expensive (not to mention an Hyperinflation process that we are living through). So, i have to try everything to save it.
Thanks in advance for you help
Regards
I have a problem with no network, radio off .
my last chance is to load a good QCN
if anyone has one for the canada variant g350w
please share. Thank you;
if i need to make a walk through how to do this i will. i thought it was common knowledge.
if anyone is interested please post or pm. its quite simple . just requires the QPST Configuration program on a pc.
https://forum.xda-developers.com/sho....php?t=2263391 - program QPST
install QPST and then plug phone into pc.
Use samsung dialer menu *#0808*# to change usb connection to RNDIS+DM+Modem
That will force pc to update drivers etc, then open QPST and at the bottom right of main menu you will see " Add new Port" Click that and then uncheck the "show serial and USB/QC Diagnostic ports only" box
this will open up 3 (probly) different COM Ports , click on one and then click "add" at the bottom.
Repeat that until one shows up on the main menu with a (0) under the phone category.
When you have that one (0) then open the drop down from the top menu "Start Clients" and then select "Software Download" from that drop down.
once in that menu, you will select "Backup" on the top row of options, and then "browse" on the right hand side, you choose the COM port with the (0) from before there.
then select an area to place the file, or a name. it may have a default name already, if so you can rename or whatever you like or keep it the same. doesnt matter.
and press start.
This will make a backup of your QCN and save it to the location you specified.
That file is what i need to hopefully resurrect my phones radio.
With QPST you can do a lot of things, this is a very minor feature, I use it to put a QCN from aws enabled s4 to the non aws one and it makes the s4 now work on aws frequencies as the phone has the capability, its just the radio (QCN) thats stopping it.
If you know what to do you can enable different bands, change imei and much more with this program.
thread can be closed. i managed to get one from a broken phone but it isnt the fix i need.