Related
I'm not a complete numpty at this as have for years been flashing my HTC devices.
However with my HD2, everytime I flash my device, I cannot make a call. It connects but there's no-one one can hear me. When I end the call the whole screen freezes and I have to take the battery out and turn on again.
If I flash back to the original LEO Rom the problem goes away.
Wierd. Any ideas please?
Are you doing a hard-reset after flashing? This means holding the volume up key and the power button at the same time until you get the message asking for confirming of a hard reset.
No - I didnt.
Doing that now. Hope the answers that easy!
I had similar problems and turned out this was it. I was doing a soft-reset instead of the required hard-reset.
Didnt work. Still the same...
Has the radio got anything to do with this?
If it helps, I did HSPL successfully and installed (independantly) radio 2.09.51.03 from HTC (not TMOUS - not that I know what that means )
jamesbond_28_007 said:
Didnt work. Still the same...
Has the radio got anything to do with this?
If it helps, I did HSPL successfully and installed (independantly) radio 2.09.51.03 from HTC (not TMOUS - not that I know what that means )
Click to expand...
Click to collapse
Yes,
In a lot of cases the Radio you use is very important. A lot of custom roms in particular require specific radios in order to allow for the 575mb ram hack. If the correct radio is not present it usually results in the phone hanging on the white HTC screen, not starting, constantly rebooting etc... Whichever rom you're using check back in that thread to see if it requires a specific radio, if it does then flash it by restarting the phone while holding the volume button in the down position (the bottom of the button) to get it into bootloader then connect the USB cable and link the phone with your PC and put the correct radio on from there.
gargon01 said:
Yes,
In a lot of cases the Radio you use is very important. A lot of custom roms in particular require specific radios in order to allow for the 575mb ram hack. If the correct radio is not present it usually results in the phone hanging on the white HTC screen, not starting, constantly rebooting etc... Whichever rom you're using check back in that thread to see if it requires a specific radio, if it does then flash it by restaring the phone while holding the volume button in the down position (the bottom of the button) to get it into bootloader then connect the USB cable to your PC and putting the correct radio on from there.
Click to expand...
Click to collapse
Would you mind suggesting a ROM with the specific Radio you know will work. I can then rule out my 'interpretation' error! Would appreciate it.
also...is the radio sometimes built in to the ROM?
jamesbond_28_007 said:
also...is the radio sometimes built in to the ROM?
Click to expand...
Click to collapse
usually just standard ROMS, not cooked ones.
hesian said:
usually just standard ROMS, not cooked ones.
Click to expand...
Click to collapse
OK, well using your post, I'm going to flash your 2.08.50.08 radio then the Energy series 23554. That should work right...
it did for me tho now i am on TOUCH_X_TREME_23554_EURO_2_30_5_54
jamesbond_28_007 said:
OK, well using your post, I'm going to flash your 2.08.50.08 radio then the Energy series 23554. That should work right...
Click to expand...
Click to collapse
yeah it should, i had a 2.07.51 radio rom on my HD2 when i tried the energy rom out first and same result as you. Did some digging about it and found that Energy rom only works with 2.08.50 radio, so flash it and you will be fine.
dkwolf said:
yeah it should, i had a 2.07.51 radio rom on my HD2 when i tried the energy rom out first and same result as you. Did some digging about it and found that Energy rom only works with 2.08.50 radio, so flash it and you will be fine.
Click to expand...
Click to collapse
OK, well thats 2.08.50 onboard. Now for Energy 23554 Apr 01.7z
Hi, this is my first post on this forum so first of all I would like to appolagise for all the things I've either just done wrong, or am about too....
I am trying to install android on to my phone, I am on the stock rom but have succsesfully installed HSPL3 and radio version 2.11.50.20.
I have tried a few builds of Android but allways have one of 2 results.
Once I've run clrcad followed by harlet, it tells me I'm booting to linux. The screen then goes black, it runs about 8 lines of code, stops there and changes to a black screen with a green HTC. Where it remains indefinatly.
A friend with anouther HD2 has android working fine on his device, and altho he has a custom rom he tells me its not essential, as ive read up on the potential risks I would rather stick with the stock but will change if thats whats causing the problem.
I would really appreciate some suggestions, thanks in advance for your time and help.
Peter
forgot to add, the second result is the screen going blue indefinatly, which I presume from my extensive knowledge.........lol is a blue screen of death
upgrade your radio, im on 2.12.50, and the newest is 2.15.50
also, try a modded windows mobile rom, i use standard energy with no issues.
also, make sure you only have that one android build on your SD card. and that it's a new build, not an ancient one. (check http://android.hd2roms.com/)
you shouldnt have any more issues.
Thanks for the advice, unfortunatly before seeing your post I uprgraded too chuckeys rom, not energy, but get the exact same error... Leads me to beleive the problem is elsewhere. Will keep trying tho hope its worth it.
Jai meme problme mon rom est miri hd2 v_18.0 wwe ? Radio 2.15.50.14 ?
Same problem here, tried to change my wm rom and didn't work. I'm looking tonight if I can find a solution...
A little disclaimer
I will not be for any damage that may be caused to your device, HSPL remove warranty so be carefull. Don't forget to have more than 50% of battery remaining before the process !
So, maybe here is the solution:
I've try again with differents roms, changing my wm rom etc. and nothing works.
But, at the end I've change my radio rom to Leo_RADIO_2.12.50.02_2 found here http://forum.xda-developers.com/showthread.php?t=611787
Then installed Chucky GTX Lite rom found here http://forum.xda-developers.com/showthread.php?t=618787
And to finish I've installed the bootloader and download MDJFroYoRevolution 1.4 with android 2.2
I've use the 512 Data img too (just unzip your MDJFroYoRevolution, take the 512 or 1Go file and put this file on your Android root.) isn't necessary but takes less time to work first time.
After that still not working so I managed to try to remove all files from my sd card (2Go only) and I put on ONLY MDJFroYoRevolution 1.4+512Mo Data img !
Then after 10mn~ it works !
I think the bug is only because sd card haven't enough space to create all files so the HTC logo stuck and no error message appear.
Don't forget to install the bootloader on your memory internal storage! and not the on the sd card!
Good luck everyone and I hope it will help.
ps: sorry for my english hope you understand anything
Having the same problem here. I've tried different versions of WM, different Android builds, updated the latest radio rom, all without success.
Strange thing is though that Android boots the first few times, but after resetting it more than about three times it gets stuck on the black screen with the HTC letters in the middle. The only way to get it running again is reformatting my SD card (8G). Only thing on it is the Mdeejay Froyo Sense v2.3 Clean...
Solution for the freeze screen after second boot
I put android not in the root directory but in a \Android directory on the SD CARD.
of course, I add set cmdline "rel_path=Android" in the Startup.txt file and now i can reboot my phone when i want.
Ghirt said:
Having the same problem here. I've tried different versions of WM, different Android builds, updated the latest radio rom, all without success.
Strange thing is though that Android boots the first few times, but after resetting it more than about three times it gets stuck on the black screen with the HTC letters in the middle. The only way to get it running again is reformatting my SD card (8G). Only thing on it is the Mdeejay Froyo Sense v2.3 Clean...
Click to expand...
Click to collapse
exactly the same issue here
ROM: Energy build 28244
Radio: 2.15.50.14
Android: MDJ FroYo Sense Clean v. 2.4
Having same issue.
Energy Rom
Just reformatted MS
Hspl 2.08
radio 2.15.50.4
htc desire android build
getting same green htc screen.
icemanscion said:
Energy Rom
Just reformatted MS
Hspl 2.08
radio 2.15.50.4
htc desire android build
getting same green htc screen.
Click to expand...
Click to collapse
Do you got this issue at the first boot or after few reboots as Ghirt and I have ?
peterbeer said:
Hi, this is my first post on this forum so first of all I would like to appolagise for all the things I've either just done wrong, or am about too....
I am trying to install android on to my phone, I am on the stock rom but have succsesfully installed HSPL3 and radio version 2.11.50.20.
I have tried a few builds of Android but allways have one of 2 results.
Once I've run clrcad followed by harlet, it tells me I'm booting to linux. The screen then goes black, it runs about 8 lines of code, stops there and changes to a black screen with a green HTC. Where it remains indefinatly.
A friend with anouther HD2 has android working fine on his device, and altho he has a custom rom he tells me its not essential, as ive read up on the potential risks I would rather stick with the stock but will change if thats whats causing the problem.
I would really appreciate some suggestions, thanks in advance for your time and hel
Peter
Click to expand...
Click to collapse
Always use the custom winmo Rom sugested by the Android Builder. Simple as. The myth of "Stock ROM will be sufficient" should end
Peter[/QUOTE]
Same problem!!
Ive updated my radio to: 2.15.50.14
tried 3 roms.
before installing radio - I had the Kernal problem.
and now I have the black screen with green htc.
has anyone found a solution?
is their something that im not doing?
thanks!
jigners said:
Always use the custom winmo Rom sugested by the Android Builder. Simple as. The myth of "Stock ROM will be sufficient" should end
Peter
Click to expand...
Click to collapse
[/QUOTE]
Not true. I've installed on a couple of peoples HD2's using the latest stock WWE rom with radio 2.15. It does work, and it works very well.
I'm not saying you shouldn't use custom roms, that is everyone's prerogative (as you can see from my sig I use VBN's rom and it's perfect for me).
Try to move a folder called Android from sd card to another folder or delete it and it should help. It worked in my case. Good luck!
has someone hear find an answer?
given up
I have tried many combos and radios and still stucked at green htc loading logo now i am just hoping for nand. strange thing its the volume down and end does not bring bootloader anymore.
I've tried to install magdlr 1.10 1.11 1.12 and 1.13, but none of them will install on to mu HD2. I can get so far as to the screen where it SHOULD be downloading, but it won't go past 0% can anyone tell me what I'n doing wrong?
What Windows version are you running?
Have you tried this thread.....http://forum.xda-developers.com/showthread.php?t=893948
lozonw said:
If you are using Windows Vista or 7, you need to right click DAF and run as admin.
Click to expand...
Click to collapse
Tried that originally; wasn't the problem.
Sorry, not DAF.exe.
It's ROMUpdateUtility.exe.
Try that.
I'm very new to this, though not the flashing of ROMS.
This may help someone as green as me...
After a few hours of staring at a black screen with some very tiny text at the top I decided to update my radio. I had a stock ROM on the HD2 so the radio version was about 2.08, I think.
Having flashed Radio 2.15.50.14 I more or less instanly had a loading screen with a nice animated Andriod, and a few minutes later was booted into Andriod.
So, make sure your Radio is fairly up to date!
yep, thats instruction 2 in pretty much all the 'how to' threads, right after '1 apply HSPL'. But finding it out the hard way will make you remember it, hehe.
Hah! I was dead tired when I posted last night and this is in the wrong thread :-(
I'll now try and put it where it belongs...
Soz
I've been searching for over 20hours around the internet for any solution to the so dreadful White Screen of Death in HD2.
This is due to a Radio Rom incopatible with the device. May be called Radio Brick! Lol
Well, it's truly desperating, as no method tried works!
The phone as soon as it's turned on just shows a white screen, no letters, no nothing.
Happened when I - dumbly - flashed a incompatible radio rom...
It has happened to a lot of other good people, but no solutions yet arrived to the internet!!!
In my case, I have hspl 2.08, and can perfectly access to bootloader, but flashing anything through SD does NOT work.
WHAT I'VE TRIED:
-flashing stock rom from HTC site, but when it comes to the radio part... UPDATE FAILED!
-tried a method here in XDA that solved a case like this but nothing... when it comes to flashing the radio, it always fails
-tried downgrading HSPL to SPL or to another version of HSPL.. curiously, the process says it was sucessfull but it changes nothing.. when i go to bootloader again the version is the same, no matter what kind of version I select...weird!
-nothing flashed through RUU works because comunication fails after 5min at 0%
-task 29 - does nothing
-changing rom/radios - always gives an error in radio update
I'm really, really, REALLY desperate, and I believe i'm not the only one in this situation!
Does someone have a brilliant idea on this?
I got it working again a couple of times but then it starts freezing after 10 hours and then i get again the whitescreen..
Now its stuck at bootloader i can't get in magldrboatloader does some1 known how i get into magldr because than i can flash another rom because in boatloader i can't flash
Hello,
I also have same problem I also cannot find a solution, Hope somebody can help us.
try j-tagging your devices !!
also it may be a hardware issue !!
good luck !!
Are you sure flashing through SD isn't working? Format the SD card new as FAT not as FAT32. And try to rename the the nbh file with into LEOIMG.NBH . Flash through a SD not a SDHC. Try this things, if they aren't working maybe j-tagging fix it.
Brain in a Nutshell said:
Are you sure flashing through SD isn't working? Format the SD card new as FAT not as FAT32. And try to rename the the nbh file with into LEOIMG.NBH . Flash through a SD not a SDHC. Try this things, if they aren't working maybe j-tagging fix it.
Click to expand...
Click to collapse
Can you send some tutorials. Because i dont know were to start and how..
I saw many people have this problem but there is no clear solution how they fixed it because they didnt gave feedback that it worked. Does some1 know how to fix this. [Desperate]
Slagers said:
I saw many people have this problem but there is no clear solution how they fixed it because they didnt gave feedback that it worked. Does some1 know how to fix this. [Desperate]
Click to expand...
Click to collapse
you'll have to try flashing your device again and again !?
but i think j tagging is the best option for this problem !! !!
you can go to the original htc store if you have not flashed hspl !!
(flashing hspl voids warranty !) !! also try to stock spl to 1.42.0000 by using hspl2 !!! http://forum.xda-developers.com/showthread.php?t=611433
if the bootloader screen (the three color screen) show 1.42.0000 spl then u can show it to the official htc stores !!
else
contact a local repair shop and try to jtag !!
may help !!
good luck !! !
So there is no fix i can do at home like flashing a specific rom or something else?
if the bootloader screen (the three color screen) show 1.42.0000 spl
Click to expand...
Click to collapse
Or 1.66.0000 or 3.03.0000
The best thing you can do is update the kernel version. I haven't had a WSOD for more than half of year.
The only kernel I've had this problem with was a rafpigna kernel on a sense rom. It was a build made in the first trimester of this year.
SPL-2.08. HSPL
I can flash it back to the normal rom from windows mobile. But i want a android version maybe some1 know a good rom and radio thats stays good?
nemuro said:
The best thing you can do is update the kernel version. I haven't had a WSOD for more than half of year.
The only kernel I've had this problem with was a rafpigna kernel on a sense rom. It was a build made in the first trimester of this year.
Click to expand...
Click to collapse
What kernel version you use now? and what rom and radio? So i can do the same things you did.
Can you put the link were you downloaded the kernel and rom and radio please. Thanks in advance nemuro!
You have all information in his signature.
Radio 2.12.50.02.2
ROM Redux2
Kernel Tytung (Redux2 have Tytung 12.4 by default)
how about hardware reset with pressing 3 keys at the same time?
Let me explain whats happing me all the time:
First my phone freezed up all the time and after a couple of weeks I got the [wsod] I can boot into bootloader (3 color screen) there I can flash it back to the original stock (WiMo6.5)
But I want android for my whatsapp and I like android. So I put maglder 1.13 on my phone. Then I tried android NAND flashing this worked but afther 10 hours my phone is off and I got the [wsod] again. I flashed my radio first to 2.15 but didnt help I tried this 2 times.
Yesterday I flashed my hd2 I followed a guide for android sd flashing I put the radio 2.12 on my phone and a old rom. I flashed it with haregt.exe it worked for 10 hours again then boom [wsod]
Im realy desperate, have some1 fixed this problem by himself already?
Did you try to run winmo for a few days? If you have problems even with stock OS most probably is hardware issue. If everything is OK running winmo then try fresh install (task29, radio, magldr, predefined recovery,ROM) of this ROM:
http://forum.xda-developers.com/showthread.php?t=1395049
For me works perfect.HD2 EU Radio 2.15.50.14
Petricanu said:
Did you try to run winmo for a few days? If you have problems even with stock OS most probably is hardware issue. If everything is OK running winmo then try fresh install (task29, radio, magldr, predefined recovery,ROM) of this ROM:
http://forum.xda-developers.com/showthread.php?t=1395049
For me works perfect.HD2 EU Radio 2.15.50.14
Click to expand...
Click to collapse
Oke im trying stock rom for a few days, I keep this thread updated if it worked or failed.
Slagers said:
Oke im trying stock rom for a few days, I keep this thread updated if it worked or failed.
Click to expand...
Click to collapse
So, it means WINMOB is working all days ok?
If no, what is the issues with WINMOB?
Taco123 said:
So, it means WINMOB is working all days ok?
If no, what is the issues with WINMOB?
Click to expand...
Click to collapse
No I cant install WinMo anymore still white screen of death if im back from work Im gona try to install WinMo again on my HD2 hopefully this time with more luck
I go into bootloader than install a stock rom from htc site than installed till 100% than I get an error that the image file is incorrupt?
Any ideas?
Hello to all of you guys, i have searched the forum but have not found a similar problem that I currently have in hands, so let me start to explain.
I have an HTC T-Mobile HD2
Model No: PB81120
SPL: 2.10.0000 8G XE
Stock Rom: Never tried to install anything or upgrade
The phone worked fine until some days ago it stopped working and hangs on boot, screen all white with the logo all messed up and stretched.
I did a softreset, an hardreset, i can boot it on Bootloader (the tri-color screen) and it detects usb.
So thinking this behavior was caused by its software I tried to reset it (soft and hard) but with no luck, if i try to install via USB the phone dont pass the 0% (and it shows no logo above the bar, only a white rectangle with some black lines), then I tried boot from the SD (8gb class 4) but it hangs on Loading... screen (searching the other threads i found that maybe I need a higher class card and if possible with only 4 or 2gb).
Running Task29 from toolkit or trying to install something from the USB does the same thing as trying to install the Stock ROM (freezes at 0%).
So my question is, am I doing somthing wrong, or do you guys have a solution for my problem? And sorry for my english.
P.S: If needed i will buy another microSD card.
P.S2: If you have any questions, I will try to answer them the best as I can.
Album
imgur.com/a/kzRMo#0
I continue with the same problem, as I am unable to post direct links in this forum, I put at the end of previous post a link to one album with pictures and screenshots I took from my phone while attempting a recovery, I hope its enough for you guys to understand whats going on.
Primordium said:
I continue with the same problem, as I am unable to post direct links in this forum, I put at the end of previous post a link to one album with pictures and screenshots I took from my phone while attempting a recovery, I hope its enough for you guys to understand whats going on.
Click to expand...
Click to collapse
Based on the second image, it looks like you're trying to re-flash WM6.5 on it, correct? FYI, v3.14.405.2 is not the latest version. I think that v3.14.531.0 is (and the filename is RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship.exe). I suggest looking for that (it's likely in a stickied thread in the WM6.5 sub-forum) and trying it. If that doesn't work, you might try downloading the latest radio and installing that first.
Another idea: could your USB cable be flakey, perhaps? If you have another that you can grab, try that.
If you can't manage to re-install WM6.5, try installing Android or Windows Phone 7 (see the respective sub-forums), instead. This guide can help you do it for Android, if you're interested.
Osprey00 said:
Based on the second screenshot, it looks like you're trying to re-flash WM6.5 on it, correct? FYI, v3.14.405.2 is not the latest version. I think that v3.14.531.0 is (and the filename is RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship.exe). I suggesting looking for that (it's likely in a stickied thread in the WM6.5 sub-forum) and trying it. If that doesn't work, you might try downloading the latest radio and installing that first.
Another idea: could your USB cable be flakey, perhaps? If you have another that you can grab, try that.
If you can't manage to re-install WM6.5, try installing Android or Windows Phone 7 (see the respective sub-forums), instead. This guide can help you do it for Android, if you're interested.
Click to expand...
Click to collapse
Ty for the fast answer, I'm donwloading the ROM right now and later i will update with the results. I cannot install Radio only version because I do not have HSPL installed, and about the USB cable, I'm using it with other devices and it's working fine. (I will try to find another USB meanwhile cable just to be sure).
Update, after downloading the ROM I tried to install it via USB but the strange behavior continues, it does not pass the 0% and after some minutes the setup fails as shown in the album I posted in the first post
I'm not sure what more you can try if you want to keep WM6.5. I suppose that you could try to install HSPL, a new radio and even MagLdr, then try to install the WM6.5 ROM again. If it fails, then just install Android or WP7, I guess. I would just do that, anyways, since WM is dead. I would go with the Android 4.3 (latest version from Google) ROM that's in my signature, but it's up to you.
Osprey00 said:
I'm not sure what more you can try if you want to keep WM6.5. I suppose that you could try to install HSPL, a new radio and even MagLdr, then try to install the WM6.5 ROM again. If it fails, then just install Android or WP7, I guess. I would just do that, anyways, since WM is dead. I would go with the Android 4.3 (latest version from Google) ROM that's in my signature, but it's up to you.
Click to expand...
Click to collapse
The problem is install anything, i cannot install HSPL or anything else by USB (phone freezes at 0%), trying to install from the microSD the behavior is hanging at Searching . . .
Primordium said:
The problem is install anything, i cannot install HSPL or anything else by USB (phone freezes at 0%), trying to install from the microSD the behavior is hanging at Searching . . .
Click to expand...
Click to collapse
Are you trying to install HSPL through HD2 Toolkit, perchance? Have you tried the standalone version? A link to it is here. I would suggest right-clicking and running it as an administrator, just in case. After that, try using the HD2 Toolkit to repartition as MagLdr or CLK. If it's still a no-go, then I don't know.
OK, I just did a search and it came up with a slew of threads that possibly describe your problem. Have you looked at any/all of these and tried the suggestions in them?
[Q] HD2 freezes at 0% during update or flash
[Q] is this HD2 bricked or... need your opinion
Hd2 white screen of death
HD2 Bricked?HELP?
[Q] How to "unbrick" HD2?
HD2 stuck on custom boot screen and won't flash anything in bootloader
my htc hd2 is STUCK.. HELP ME PLS
[Q] Htc hd2 stuck on white screen
[Q] Unable to flash any ROM!
I realize that not all of them describe your situation perfectly, but the replies may still be helpful. There are a lot of things to try. I would read each of them carefully and try them all (as well as check that, the ones that you've already tried, you did the right way).