Related
Hi, I bought a Sony Ericsson Xperia X2 and decided to update the firmware through SE Update Suite. In the middle of firmware update, the computer BSoDed on me. The phone went dead and the PC did not detect it any more (Unknown USB device in device manager).
Eventually I managed to detect the phone by SEUS (on another machine); now I have a "COMXX SSE X2 Software DOWNLOAD" in device manager. I follow the instructions in SEUS to update the firmware, press and hold Vol Down + Power buttons. The phone vibrates and device manager shows "COMXX SE X2 Software DOWNLOAD", but SEUS does not update the phone.
What can I do to recover the phone?
update firmware
How can I update firmware from card?
bdadabayev said:
How can I update firmware from card?
Click to expand...
Click to collapse
???
You have to do it through SEUS.
don't worry
this happened to me too. heres what you do read all the steps before you do it
first go ahead and charge you phone just plug it into the wall then follow these directions
1.) start suess and continue like you normally would
2.) remove your battery cover and leave it off
2.) when you get to the step that asks you to plug in your phone, connect your phone via usb to you computer, then hold the down volume button + the power button + while you are holding these buttons push the soft restart button* do this all at once and do not let go of any of the buttons until you see the white screen with the sony ericson logo and it should update like normal.
*to get to the soft restart look at the back of the phone with the battery cover off, now pull out the stylus right there next to you camera where you stylus came out is a little button push it with your stylus.
this worked for me when i thought i bricked my phone and it worked, so good luck and tell me how it works out
doministry said:
???
You have to do it through SEUS.
Click to expand...
Click to collapse
Can I flash without SEUS, other methods?
yummy-fun said:
this happened to me too. heres what you do read all the steps before you do it
first go ahead and charge you phone just plug it into the wall then follow these directions
1.) start suess and continue like you normally would
2.) remove your battery cover and leave it off
2.) when you get to the step that asks you to plug in your phone, connect your phone via usb to you computer, then hold the down volume button + the power button + while you are holding these buttons push the soft restart button* do this all at once and do not let go of any of the buttons until you see the white screen with the sony ericson logo and it should update like normal.
*to get to the soft restart look at the back of the phone with the battery cover off, now pull out the stylus right there next to you camera where you stylus came out is a little button push it with your stylus.
this worked for me when i thought i bricked my phone and it worked, so good luck and tell me how it works out
Click to expand...
Click to collapse
doesn't wurk, device unknown maybe you didn't brick your phone, that's why it was still booting to logo screen...
I noticed that "COMXX SSE X2 Software DOWNLOAD" device appears in Device manager when the Volume UP is pressed on boot instead of Volume DOWN.
One more thing... There is a useful piece of software out there called QPST (Qualcomm Phone Service Tool). When I have the phone in download mode it detects the device (since it's Qualcomm platform, pretty much like ZTE 3G modems). But I don't have loaders or software to flash the phone baseband from QPST. Maybe if someone can parse the firmware available on the Net and extract the said loaders and software, then I could flash the Baseband and get the phone detected by SEUS to continue flashing Windows part. Unfortunately, decrypting the firmware is way beyond my knowledge. Anyone more knowledgeable on this subject?
First of all: Charge your phone for at least 2 hours from wall charger. I have experienced that it does not charge from USB always, especially when in update mode.
Please try this if you have only charged from USB previously.
Prydplante said:
First of all: Charge your phone for at least 2 hours from wall charger. I have experienced that it does not charge from USB always, especially when in update mode.
Please try this if you have only charged from USB previously.
Click to expand...
Click to collapse
Thanks for your advice, but I am aware that phones don't always get full charge with damaged firmware. That is why I took the battery out and charged it fully with a special charger for batteries.
Need help
Can anybody help? - Problem is that i cant "push" my phone to go to bootloader (tried soft-reset, vol down+shut down..nothing helps), so it i cant update via SEUS. And after trying to instal manualy R3 cab's, "Clear phone memory" is gone - now i even can't reset my phone.
Anybody, please help.
what i think you trying to do is boot the rom from the sd card is that right? if you are, it won't work because you need a alternative bootloader or a hard-spl which the x2 doesn't have... yet. thats why we HAVE to use SUES. if you can't get your computer to recognize your phone even after charging it in you special charger and forcing it into bootloader via SUESS (the option i pitched earlier) your best bet is to contact Sony Ericsson or who ever you bought it from and tell them they sold you a faulty device and they HAVE to replace it. if you get the opportunity to talk to them on the phone be firm and don't ever place fault on yourself and push that they sold you a broken device, hopefully they will send you a new one. i'm sorry i couldn't help. At this time my knowledge in Winmo is ignorant at best. good luck
anyone know how to help?? i also have this problem.... ><
Down volume button + the power button doesn't have the logo of SE..
and the SEUS can't detect my x2... wanna cry//
Hi!
Do exactly like this:
1 Charge the battery with the wall charger to at least 50.
2 Remove all cables connected to X2. This is important!
3 Remove and re-insert battery.
4 Push and hold volume down.
5 While still holding volume down, push and hold Power at the same time.
6 Hold until SE logo on white background appears, then release both buttons.
7 Now connect USB cable.
Be careful to follow this exactly or it will not work!
x2 prob
I have same problem in my phone , during update with SEUS computer hang and now
my phone shows only vibrate.
i have tried volume down+power+reset
but it can't go to white screen or sonyericsson logo.
any other solution
bdadabayev said:
Thanks for your advice, but I am aware that phones don't always get full charge with damaged firmware. That is why I took the battery out and charged it fully with a special charger for batteries.
Click to expand...
Click to collapse
Or You might need go to " C " drive - Progam files _ sony Ericson than remove any SEUS in that folder befor you go to inStall new F/Ware up date , everytime you want to reflash new SEUS you have to remove the last time F/Ware evenly that is the same one SEUS .than you go on for update new F/Ware SEUS to your phone .
Here is the support site for US. SE has a dedicated Nr and mail for x2.
what about new's for xperia x2 flashing
i have one stuck on logo after installing cab
and seus say's that no new update
Rise said:
I have same problem in my phone , during update with SEUS computer hang and now
my phone shows only vibrate.
i have tried volume down+power+reset
but it can't go to white screen or sonyericsson logo.
any other solution
Click to expand...
Click to collapse
same problem i have
is there anythng new?
what to do is any way to fix it?
X2 morto !!!
I have the same problem, now I try to modify the language of my phone, just missing to finish the installation program displayed an error message and now I can not in flash mode puts you ... what friends do?
hi i have flashed cm902 rom it booted up but it dont like me cause makes eroros so i wanted ro reflash with old stock 2,3,3 and with recovery bootstrap i thinked what i wild came into recovery but it just hanged and now no recovery only white triangle with yelow! and only logo m, so maybe someone hav this problem earlier and can help me?cause now im searching half day of work for searching for solution.
thanks fo anny help
Dont worry. Do this. First use the wall charger and charge your phone for at least 30mins. So if your phone is off then it will charge till 70-80%. Check if it is charging by looking at the micro-usb port lighting up.
Now go to the White triangle with ! mark. Then press @ button. You will get options. Select erase data by pressing volume button and then clicking enter button on your keypad.
After the wipe has been done pull out battery. Then start RSD Lite on your computer. Put the battery to your phone. Now press both volume up and volume down together and then power button for 2secs. Leave power button. You will see it in bootloader.
Now load sbf file on RSD software and wait for it to recognize your phone. Then click start. Thats it. Your phone should be ok.
Hello guys,
I know these topic is there a lot of times wrote, but i found i have one more problem that the others.
I was installing custom rom through TWRP, it looked like all went successful but phone get stucked on huawei logo.
I tried a lot of things from lot of forums. I downloaded update.app, basic recovery, but when i wanted to install it. I recognize
I didnt charge phone through night. Now my phone is discharged and i cannot go into TWRP or fastboot. When i plug it into charger
it charge only to start bootloop ( i suppose). i cannot go to twrp or fastboot cause when i hit volume up and power button, telephone just restarts
and shows he is discharged. When i let it to do what it want, it charge a little, then start bootloop. After bootloop discharge battery, process start again
It looks like phone will charge only a little just for bootloop for a small time.
Anybody knows what to do? I am sad
Nidure said:
Hello guys,
I know these topic is there a lot of times wrote, but i found i have one more problem that the others.
I was installing custom rom through TWRP, it looked like all went successful but phone get stucked on huawei logo.
I tried a lot of things from lot of forums. I downloaded update.app, basic recovery, but when i wanted to install it. I recognize
I didnt charge phone through night. Now my phone is discharged and i cannot go into TWRP or fastboot. When i plug it into charger
it charge only to start bootloop ( i suppose). i cannot go to twrp or fastboot cause when i hit volume up and power button, telephone just restarts
and shows he is discharged. When i let it to do what it want, it charge a little, then start bootloop. After bootloop discharge battery, process start again
It looks like phone will charge only a little just for bootloop for a small time.
Anybody knows what to do? I am sad
Click to expand...
Click to collapse
Just put it for charge don't wory about bootloop after sometime disconnect charger and hold all three (volume and power) button until you see Huawei Logo....Theb release power and keep holding volume buttons....
And remember to put your UPDATE.APP in dload folder on your SD card before all of it
HaiderHady said:
Just put it for charge don't wory about bootloop after sometime disconnect charger and hold all three (volume and power) button until you see Huawei Logo....Theb release power and keep holding volume buttons....
And remember to put your UPDATE.APP in dload folder on your SD card before all of it
Click to expand...
Click to collapse
thanks, but dont i have to install stock recovery first? i thought i removed upgrade one when i installed TWRP...
but ill try to have it in charge for hour then ill try holding buttons.
Update:
I let phone in charger for a hour. After hour it is still flashing red, when i try to hold buttons, phone just turn off and then flash red.
<- it didnt charged.. i still think problem is it charge a little, then start booting, --> booting discharge phone --> phone will turn off --> automatically
start charging a little --> then it start booting again --->then it repeats.
I know I am stupid, i should just let it in TWRP before it discharged, but it happened what now?
It looks like my problem is to charge now, do i have to do some manual charge?
Nidure said:
thanks, but dont i have to install stock recovery first? i thought i removed upgrade one when i installed TWRP...
but ill try to have it in charge for hour then ill try holding buttons.
Update:
I let phone in charger for a hour. After hour it is still flashing red, when i try to hold buttons, phone just turn off and then flash red.
<- it didnt charged.. i still think problem is it charge a little, then start booting, --> booting discharge phone --> phone will turn off --> automatically
start charging a little --> then it start booting again --->then it repeats.
I know I am stupid, i should just let it in TWRP before it discharged, but it happened what now?
It looks like my problem is to charge now, do i have to do some manual charge?
Click to expand...
Click to collapse
I have the exact same problem, sitting here with my bootlooping p8 lite and can't charge it.
I charged it overnight and even then it was flashing red and showing that the battery is low.
Can't boot into recovery (TWRP) or Bootloader, just don't know what to do, is there a method to charge it or boot somehow?
Sometimes you need phone to be connected to pc to reboot into bootloader. I have read from somewhere that if you connect phone to pc and hold only "volume -" it will boot(I haven't tested myself). I once had similiar problem with honor 4x and just trying to reboot it like 3h it somehow got to bootloader. I also had problem not charging.
keikari said:
Sometimes you need phone to be connected to pc to reboot into bootloader. I have read from somewhere that if you connect phone to pc and hold only "volume -" it will boot(I haven't tested myself). I once had similiar problem with honor 4x and just trying to reboot it like 3h it somehow got to bootloader. I also had problem not charging.
Click to expand...
Click to collapse
Alright, I've already tried it when connected to pc. But I'll try it once again with just pressing volume down
I'll give there update
Nidure said:
Alright, I've already tried it when connected to pc. But I'll try it once again with just pressing volume down
I'll give there update
Click to expand...
Click to collapse
Conectado​ to PC try power button plus volume up.
if anyone curious. just block volume down with some gum or chain or something and then put it to charger. It will not start bootlooping
Had the same problem just let the phone discharge for a few days (when you press the power button it should not blink red) then hold the volume button in the middle and plug it into the pc it should boot into recovery mode. Download the stock firmware for your model(UPDATE.app) and use the update extractor to get the boot, system, cust & recovery images and install them using fastboot commands. Or you could download the unbrick files from the mega thread for your device (dual or single sim) and replace the boot, cust, system & recovery images with the ones of your stock firmware and the use the install bat
I solved this problem by disconnecting the battery 3 months ago
Hi
i bought before 2 weeks Xiaomi a1
it wored very good.
Today while I wanted to turn on the screen it did not respond.
The phone is not responding to any type of pressing.
I must say that the phone is new, did not get any kind of hit , and 5 min before this problem it used to work really good.
I think that the phone is in brick mode, and i can't enter to fastboot option because the phone is not responding....
Pls help my solve this problem.
Thanks
Try holding the pwoer button for more then 10 seconds, that should reset it... once you start it up aghain turn of ambient screen... Gave me troubles too... Hope that helps.
Has that still not been fixed with November update? I turned my ambient screen back on to see. So far, 2 days since update and no black screen after notification.
I'm guessing it's not dead. I have the same problem before as well. It was the buggy Ambient Display. Force restart your phone by pressing power button and holding it more than 10 second. First thing on boot up complete, go to Settings > Display and turn off Ambient Display.
micleftic said:
Try holding the pwoer button for more then 10 seconds, that should reset it... once you start it up aghain turn of ambient screen... Gave me troubles too... Hope that helps.
Click to expand...
Click to collapse
I cant even turn on the screen...
It's not showing any thing on the screen.
I tried to push the power but there is no respond
myself379 said:
I'm guessing it's not dead. I have the same problem before as well. It was the buggy Ambient Display. Force restart your phone by pressing power button and holding it more than 10 second. First thing on boot up complete, go to Settings > Display and turn off Ambient Display.
Click to expand...
Click to collapse
I tried forcing it. But it is still show black screen.
I think it is in brick mode
roy123456 said:
I tried forcing it. But it is still show black screen.
I think it is in brick mode
Click to expand...
Click to collapse
Just go in fastboot mode and reflash the firmware from MIUI.con
jack_21 said:
Just go in fastboot mode and reflash the firmware from MIUI.con
Click to expand...
Click to collapse
How can I enter the fastboot mode?
I cant even turn it on.
It is not respoding.
I tried to put it on this mode but the screen is still black.
roy123456 said:
How can I enter the fastboot mode?
I cant even turn it on.
It is not respoding.
I tried to put it on this mode but the screen is still black.
Click to expand...
Click to collapse
You must keep pressed vol down + power until the phone does show "FASTBOOT"
jack_21 said:
You must keep pressed vol down + power until the phone does show "FASTBOOT"
Click to expand...
Click to collapse
How long?
I tried it for 3 min ...
Is it enough?
roy123456 said:
How long?
I tried it for 3 min ...
Is it enough?
Click to expand...
Click to collapse
Well there is something strange.
Leave the phone discharge
Then let it charge
Then power on with vol down + power
Try these 2 things
1) charge your phone for 2-3 hours. if didnt switch on try this 2
2) Connect your data cable with pc. In mobile Press volume up + volume down and plug in the other end of usb cable to your mobile. you need to hold the keys. this will boot your phone into fastboot.
If boot steps didnt work then it might be a hardware problem or hard brick.
selvarajrajkanna said:
Try these 2 things
1) charge your phone for 2-3 hours. if didnt switch on try this 2
2) Connect your data cable with pc. In mobile Press volume up + volume down and plug in the other end of usb cable to your mobile. you need to hold the keys. this will boot your phone into fastboot.
If boot steps didnt work then it might be a hardware problem or hard brick.
Click to expand...
Click to collapse
What can I do if it is a hard brick?
roy123456 said:
What can I do if it is a hard brick?
Click to expand...
Click to collapse
Visit customer care(they will probably say motherboard problem as always) or try qfil method which is quite complex if this flashing things are new to you.
roy123456 said:
How long?
I tried it for 3 min ...
Is it enough?
Click to expand...
Click to collapse
you should press the power key while charging cable connected.If it doesn't work , unplug the charging usb and plug again reverse(type c's reversibility).If it can't, try with another AC source,another person,another location.
My A1 reborn by my gf's charging adaptor,hand and location.(she know nothing about android hard key combination)
Just thinking,don't know exactly.Sorry for my english.
My was hang.. so I restarted it.. but aftr tht.. phone is not turning on.. its just showing anroid one.. and nothhing else
ruhi maallivk said:
My was hang.. so I restarted it.. but aftr tht.. phone is not turning on.. its just showing anroid one.. and nothhing else
Click to expand...
Click to collapse
reflash phone with stock firmware in fastboot mode on MI FLASH TOOL
selvarajrajkanna said:
Try these 2 things
1) charge your phone for 2-3 hours. if didnt switch on try this 2
2) Connect your data cable with pc. In mobile Press volume up + volume down and plug in the other end of usb cable to your mobile. you need to hold the keys. this will boot your phone into fastboot.
If boot steps didnt work then it might be a hardware problem or hard brick.
Click to expand...
Click to collapse
I need help on urgent basis
I'm using Mi A1 rooted with custom kernel, My phone automatically received august update and it's installed automatically then i try to go in download mode to flash my phone with stock rom but i didn't press volume button properly and it's get restart and automatically start installing august update and i by mistake press power button and now my phone is not turning on even not responding
when i try to connect my phone with pc i can hear the connect sound but it's not going in fast boot
Shivam.S said:
I need help on urgent basis
I'm using Mi A1 rooted with custom kernel, My phone automatically received august update and it's installed automatically then i try to go in download mode to flash my phone with stock rom but i didn't press volume button properly and it's get restart and automatically start installing august update and i by mistake press power button and now my phone is not turning on even not responding
when i try to connect my phone with pc i can hear the connect sound but it's not going in fast boot
Click to expand...
Click to collapse
You switched off the phone in middle of installing ota, best bet is take it to the take it to the service center and tell them phone not switching back on after installing August ota update.
Or if not in warranty then try to install stock rom using qfil.
Unfortunately you have bricked your Mi A1
Shivam.S said:
I need help on urgent basis
I'm using Mi A1 rooted with custom kernel, My phone automatically received august update and it's installed automatically then i try to go in download mode to flash my phone with stock rom but i didn't press volume button properly and it's get restart and automatically start installing august update and i by mistake press power button and now my phone is not turning on even not responding
when i try to connect my phone with pc i can hear the connect sound but it's not going in fast boot
Click to expand...
Click to collapse
You have bricked your Mi A1, when you turned it off while installing/flashing the August update. Basically you should never turn a smartphone off, or disconnect the USB cable (if it is connected), while flashing its ROM.
There are various methods to unbrick it, I suggest you try this one since it's apparently not going into fast boot:
[Experimental]Recover Hard Bricked Xiaomi A1 Using SD Card
I need help on urgent basis
I'm using Mi A1 rooted with custom kernel, My phone automatically received august update and it's installed automatically then i try to go in download mode to flash my phone with stock rom but i didn't press volume button properly and it's get restart and automatically start installing august update and i by mistake press power button and now my phone is not turning on even not showing any logo and not detecting in pc as well
i tried to hold power button more then 30 second and 1 or 2 minutes but not turning on power
please help me