Database Users

Error 270

I really hate to make a bad first impression but...
No matter what I do I get this error. I was trying to HARDSPL the phone, I put it into boot loader mode, I installed all the .cab's . It starts the progress bar up gets to about 3% and the phone screen goes black and restarts and then ERROR 270 shows up in the RUU. I searched around but found nothing for the Herald about it. Just asking for any help as to what I can do.
Thank you in advance.

diacronic said:
I really hate to make a bad first impression but...
No matter what I do I get this error. I was trying to HARDSPL the phone, I put it into boot loader mode, I installed all the .cab's . It starts the progress bar up gets to about 3% and the phone screen goes black and restarts and then ERROR 270 shows up in the RUU. I searched around but found nothing for the Herald about it. Just asking for any help as to what I can do.
Thank you in advance.
Click to expand...
Click to collapse
Have you tried going to start/system/usb to pc and enable advanced network functionality? What rom are you running?

dougstoner said:
Have you tried going to start/system/usb to pc and enable advanced network functionality? What rom are you running?
Click to expand...
Click to collapse
ok that was disabled. I enabled it, same problem.
Seems to be running Open Touch 5.0.
Just bought it off ebay.

Ok think I got it. Seems to be very hard to find a newbie guide for first timers of this sort of thing.
Found some files by ivanmmj and sifted through them. Found a USPL program that SID unlocked the phone, after that I was able to run HARD SPL, and everything was fine. Now my next step is to try to flash a ROM on it , wish me luck.
Think after all this work I'm going to try to write a guide for first timers like me to explain this stuff a little better.

If it had OpenTouch 5.0, it might have already been HardSPLed. Either way, I'm glad you found the answer yourself. It shows that you actually did your research.

diacronic said:
Ok think I got it. Seems to be very hard to find a newbie guide for first timers of this sort of thing.
Found some files by ivanmmj and sifted through them. Found a USPL program that SID unlocked the phone, after that I was able to run HARD SPL, and everything was fine. Now my next step is to try to flash a ROM on it , wish me luck.
Think after all this work I'm going to try to write a guide for first timers like me to explain this stuff a little better.
Click to expand...
Click to collapse
That's really not a bad idea. I know I was EXTREMELY confused the first time I flashed my rom. It took me a lot of reading to finally understand RUU stood for rom update utility. You do know for some roms, it's not necessary to hard spl. I went from stock rom to open touch 3.0. What rom are you thinking about flashing to?

There's a walkthrough by me somewhere in the forums.

dougstoner said:
.... I went from stock rom to open touch 3.0. What rom are you thinking about flashing to?
Click to expand...
Click to collapse
Just downloaded ivan's kitchen , but I'm having problems getting it to run. Going to use that to probably make my own and get used to the programs that are out there.

HELP!! would like to htc back to Original settings

hello there,
I have flashed my T-Mobile Wing and i currently have TouchFlo.
Unfortunately i'm having mayor problems with this O.S., It constanly freezes, if i'm writting a text it will go back to the home page without me doing anything, I have an outlook account every time I go to my e-mails to see them it freezes and it wont do anything else i have to reset the device.
Great looks, wont denie that, but it's just not working for me.
If someone could help me return my T-mobile wing back to O.G. settings.
Please I would Greatly apprecitated!!!

miltus said:
hello there,
I have flashed my T-Mobile Wing and i currently have TouchFlo.
Unfortunately i'm having mayor problems with this O.S., It constanly freezes, if i'm writting a text it will go back to the home page without me doing anything, I have an outlook account every time I go to my e-mails to see them it freezes and it wont do anything else i have to reset the device.
Great looks, wont denie that, but it's just not working for me.
If someone could help me return my T-mobile wing back to O.G. settings.
Please I would Greatly apprecitated!!!
Click to expand...
Click to collapse
I assume you flashed another ROM and not just installed TouchFlo onto your stock ROM? How did you flash the ROM, what ROM did you flash? Has the freezing always been this way since you flashed?
Sorry I can't give a ton of answers without more information.

ok ok .... to start out i'm a mayor nub when it comes to this..
onward, I saw a video on youtube with directions on how to flash your device...ok i plugged my T-mobile usb to my my laptop i downloaded a .rar file named "flashing with rapi enabled" It told me to put this rapi folder that was in the .rar file in my t-mobile documents,i extracted the file in desktop, double clicked it and this black box appeared with and started to to its thing.. thats it i think i flashed it DID I? The freezing started ever since i got it.
thanks for your prompt reply man appreciate it!!

Okay... The method you used is called a USPL flash. Is the device you are using a T-Mobile Wing?
EDIT: Just read your first post, nevermind about that question.
You have two choices here. You can flash back to the stock ROM... You can do this by downloading the T-Mo Stock ROM from here: http://forum.xda-developers.com/showthread.php?t=321717 . Put the phone in bootloader by holding the camera button while pressing the stylus into the reset hole. Maker sure the phone is connected to your computer. Run the installer.
or
You can flash another ROM like JustStable v2 or JustHome. You can find more info here: http://thewingster.com/ivanmmj.aspx This is what I recommend as they are great and fast ROMs. A lot faster than the stock ROM. TO flash these, you can follow the same directions you saw in the video. Just replace the nbh file in the RUU folder with the one you download from that site. Note: You cannot flash any of the ROMs marked with LZX or Micro with the method you followed before

Thanks man! I honestly thank you!
just one last question:
on your NOTE ABOUT LZX OR MICRO ROMS how would i tell which is which? are the ROMS that you are recommending LZX OR MICRO? i really dont understand.
Thanks man!!

miltus said:
Thanks man! I honestly thank you!
just one last question:
on your NOTE ABOUT LZX OR MICRO ROMS how would i tell which is which? are the ROMS that you are recommending LZX OR MICRO? i really dont understand.
Thanks man!!
Click to expand...
Click to collapse
On the link I gave you. Next to the name and version they tell you JustHome LZX, or JustStable Micro.

Thank you!!! I just flashed my t-mobile wing with justhome great stuff thnak you for all your help!!! Thank you!!!

miltus said:
Thank you!!! I just flashed my t-mobile wing with justhome great stuff thnak you for all your help!!! Thank you!!!
Click to expand...
Click to collapse
Okay, I'm glad I could help! Now that you have JustHome running, if you experience any problems or bugs, post them on this JustHome forum thread here: http://forum.xda-developers.com/showthread.php?t=498140 .

I will do that man!! Once again thank you!!!

miltus said:
hello there,
I have flashed my T-Mobile Wing and i currently have TouchFlo.
Unfortunately i'm having mayor problems with this O.S., It constanly freezes, if i'm writting a text it will go back to the home page without me doing anything, I have an outlook account every time I go to my e-mails to see them it freezes and it wont do anything else i have to reset the device.
Great looks, wont denie that, but it's just not working for me.
If someone could help me return my T-mobile wing back to O.G. settings.
Please I would Greatly apprecitated!!!
Click to expand...
Click to collapse
alright man u came to da right place
first if u still have ur touchflo rom installed then good
now hard reset the touchflo if it freezes try as many time as you can get to the point where it restarts
then when it restart connect ur wing to pc and download the pagepool size
http://www.megaupload.com/?d=JB2AC9FD
then open it (make sure active sync is enabled)
then open it there are couple of .nb and .bat files
open 6mb or 8mb (which changes the pagepool)
6mb is recommened
on ur wing it going to ask to open some file
(on custom roms it wont ask)
so after dat then it should exit itself
then disconnect usb from pc and reset ur wing (use a pen or something pointy to press the reset button on the left under volume button)
Well miltus, u just got ur wing back!!!!!!!!!!
trust me it wont freeze anymore on start up or anyway
it might freeze if you keep sliding it back and forth
it will freeze if TOO many programs running in backround example if 20 programs running then yes it will freeze.
oh yeah if u still have official rom (4.10.2.523 something like that)
then this will work, only it will be faster!!!
oh yeah say thinks!!!!!!!

thanks for the feed back man appreciate it!! but i changed the TouchFlo for another ROM named JUSTHOME WORKS GREAT!!!
Thank you for your help!!!

Cannot connect with USB

Hi all
I have installed Dutty's ROM, and sometimes its unresponsive, when i click on the screen. So I wish to flash the ROM again and install the Windows Mobile 6.5. However, I cannot connect my device through USB, its not even detecting it.
What can I do to fix this problem?
Thanks a lot for your help and advice

jmonfu said:
Hi all
I have installed Dutty's ROM, and sometimes its unresponsive, when i click on the screen. So I wish to flash the ROM again and install the Windows Mobile 6.5. However, I cannot connect my device through USB, its not even detecting it.
What can I do to fix this problem?
Thanks a lot for your help and advice
Click to expand...
Click to collapse
What have you tried? Have you pulled your USB out of Phone and PC?
Have you soft reset your phone?
Put a bit more detail and we can help

ok so first i used the Unsigned_HardSPL_for_Blackstone_OliNex with ActiveSync and that worked fine. Then I moved the BLACIMG.nbh into the BlackstoneRUUWrapper to install the new ROM, and that worked fine too, 100%. Then I removed the USB cable and restarted the device. Now I am noticing that the device is working properly for maybe 10 secs, but then it freezez, and I have to resett it

jmonfu said:
ok so first i used the Unsigned_HardSPL_for_Blackstone_OliNex with ActiveSync and that worked fine. Then I moved the BLACIMG.nbh into the BlackstoneRUUWrapper to install the new ROM, and that worked fine too, 100%. Then I removed the USB cable and restarted the device. Now I am noticing that the device is working properly for maybe 10 secs, but then it freezez, and I have to resett it
Click to expand...
Click to collapse
Usually after a flash its recommended to Hard reset atleast 2 times did you do that?
Did you follow crackwhores instructions completely?
When I have flashed I wait till the finish screen on pc shows the phone should shut down and restart itself thats when i disconnect USB
when phone shows welcome screen i pull battery out and hard reset

oh so when everything is finished, and there is the FINISH screen on the PC, you should take the battery out and hard reset! Did not do this. New to all this. Managed to connect my device again by USB, and putting Miri's WM 6.5. Will hard reset after that

jmonfu said:
oh so when everything is finished, and there is the FINISH screen on the PC, you should take the battery out and hard reset! Did not do this. New to all this. Managed to connect my device again by USB, and putting Miri's WM 6.5. Will hard reset after that
Click to expand...
Click to collapse
Cool
have a reread of crackwhore thread its very helpful

thanks mate

jmonfu said:
thanks mate
Click to expand...
Click to collapse
No Problem
I have been help all through this site
its great bunch of people

Hi Ozmoran
I still have problems with my device, first it works for a number of minutes, then freezes, then after around 5 minutes comes back to normal. And secondly, cannot get my reception to work, ie cannot receive calls and messages at the moment. Its asking me, "Do you want to turn the phone on?" and when i click on yes, nothing happens.
This is the exact procedure I am following:-
1) Unsigned_HardSPL_for_Blackstone_OliNex. After 100%, I click on Finish on the PC, and remove USB cable. I remove the battery off and on again and I hard reset (from the small button on the back right?)
2) I do the same procedure for BLACIMG.nbh and that works fine too, 100% finished.
After this, first I notice that the colours are not vivid colours, but like an old PC colours, so i turn off and on the device (from the button at the top). Then after loading, its asking me to click on the "+" to align the screen, which I do, follow the next screen, and the ROM is working.
However as I said, sometimes its unresponsive, and cannot get reception from my mobile provider.
What am I doing wrong?
Thanks a lot for your help, I am a complete newbie

ok found this thread
http://forum.xda-developers.com/showthread.php?t=505377
will follow it this eve and see what happens

Reason you are experiencing this discolourization and not reception/signal is due to you most likely not following flashing procedure properly and possibly using wrong HSPL before flashing rom.
You need to use HSPL 1.56 to flash a 1.56+ based rom. Any previous version you need to use 1.14 HSPL.
I notice you have already found cRaCKwHoRe's guide. If you follow it, you will be fine. If you get stuck, just post a query inhis thread and someone will help you!!

great
i downloaded everything from that post and will do it this evening since the phone is at home.
Hopefully I can use my phone again very soon

If you also read this section in the wiki, it refers to your greenish discolourization as well and offers assistance. Though if you follow cRaCKwHoRe's guide you'll be fine

thanks guys
any preference on any particular ROMS that are popular?
I was going to try Miri's WM6.5

jmonfu said:
thanks guys
any preference on any particular ROMS that are popular?
I was going to try Miri's WM6.5
Click to expand...
Click to collapse
Good rom to start with if you want wm6.5, would also try EnergyROM HD by NRGZ28. Both excellent roms. As for wm6.1, IMHO Duttys is the best.
For you, I would try each and make your own opinion

Thanks
Will try Miri than and see how it goes
Last question (hopefully), once I will install the Hard SPL, there is no need to install it again if I want to flash the ROM again right? Just install the ROM i want
Thanks a lot for all your help!

jmonfu said:
Thanks
Will try Miri than and see how it goes
Last question (hopefully), once I will install the Hard SPL, there is no need to install it again if I want to flash the ROM again right? Just install the ROM i want
Thanks a lot for all your help!
Click to expand...
Click to collapse
Yes, once you install HSPL its permanent and you have no need to re-install it. You can restore default SPL at a later stage if you want.
USPL is temporary and needs to be re-used before every flash to new radio or rom
If I were you, I'd read up on both USPL & HSPL in the wiki for a better understanding before you jump in head first!!

yeah i will read more about it, just wanted to experiment.
Thanks for all your help!

Hey guys
managed to do it! Flashed the ROM and working perfectly now!
Thanks a lot for your help and time

[Q] Problems installing Android NAND

This is a noob question but I cannot find the answer in the forums.
I have a HD2 with WinMo 6.5 on it.
I wanted to install a NAND version of Android so I started looking into it. I believe there are several steps but I cannot do any. If I want to upgrade the radio or use MGRLDR111 to boot to the usb flasher menu the phone just freezes.
I run the RUU of either and the phone reboots, I get the colored screen then it goes to the HTC screen with the progress bar and nothing happens.
I am sure this is a noob question and someone will point me in the direction of a link where this question has been asked before but its doing my head in. All help greatly appreciated.

s1lentb0b! said:
This is a noob question but I cannot find the answer in the forums.
I have a HD2 with WinMo 6.5 on it.
I wanted to install a NAND version of Android so I started looking into it. I believe there are several steps but I cannot do any. If I want to upgrade the radio or use MGRLDR111 to boot to the usb flasher menu the phone just freezes.
I run the RUU of either and the phone reboots, I get the colored screen then it goes to the HTC screen with the progress bar and nothing happens.
I am sure this is a noob question and someone will point me in the direction of a link where this question has been asked before but its doing my head in. All help greatly appreciated.
Click to expand...
Click to collapse
You have your Winmo running ok right now? If so. Have you installed Active Sync on your PC?
http://forum.xda-developers.com/showthread.php?t=893948
Hope this can help you..

Thanks for the help above, I am getting closer.....I think.
It looks like I need to downgrade my spl first as I have 3.03.0000. From the posts I have read it appears you need to do this with an official rom.
Does anyone know where to obtain these. The phone is from Virgin in the UK.
All help greatly appreciated.

try this: http://forum.xda-developers.com/showthread.php?t=578920

Excellent thanks for your help both, greatly appreciated

[Q] Strange Behavior on TMOUS (Pictures Inside)

Hello to all of you guys, i have searched the forum but have not found a similar problem that I currently have in hands, so let me start to explain.
I have an HTC T-Mobile HD2
Model No: PB81120
SPL: 2.10.0000 8G XE
Stock Rom: Never tried to install anything or upgrade
The phone worked fine until some days ago it stopped working and hangs on boot, screen all white with the logo all messed up and stretched.
I did a softreset, an hardreset, i can boot it on Bootloader (the tri-color screen) and it detects usb.
So thinking this behavior was caused by its software I tried to reset it (soft and hard) but with no luck, if i try to install via USB the phone dont pass the 0% (and it shows no logo above the bar, only a white rectangle with some black lines), then I tried boot from the SD (8gb class 4) but it hangs on Loading... screen (searching the other threads i found that maybe I need a higher class card and if possible with only 4 or 2gb).
Running Task29 from toolkit or trying to install something from the USB does the same thing as trying to install the Stock ROM (freezes at 0%).
So my question is, am I doing somthing wrong, or do you guys have a solution for my problem? And sorry for my english.
P.S: If needed i will buy another microSD card.
P.S2: If you have any questions, I will try to answer them the best as I can.
Album
imgur.com/a/kzRMo#0

I continue with the same problem, as I am unable to post direct links in this forum, I put at the end of previous post a link to one album with pictures and screenshots I took from my phone while attempting a recovery, I hope its enough for you guys to understand whats going on.

Primordium said:
I continue with the same problem, as I am unable to post direct links in this forum, I put at the end of previous post a link to one album with pictures and screenshots I took from my phone while attempting a recovery, I hope its enough for you guys to understand whats going on.
Click to expand...
Click to collapse
Based on the second image, it looks like you're trying to re-flash WM6.5 on it, correct? FYI, v3.14.405.2 is not the latest version. I think that v3.14.531.0 is (and the filename is RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship.exe). I suggest looking for that (it's likely in a stickied thread in the WM6.5 sub-forum) and trying it. If that doesn't work, you might try downloading the latest radio and installing that first.
Another idea: could your USB cable be flakey, perhaps? If you have another that you can grab, try that.
If you can't manage to re-install WM6.5, try installing Android or Windows Phone 7 (see the respective sub-forums), instead. This guide can help you do it for Android, if you're interested.

Osprey00 said:
Based on the second screenshot, it looks like you're trying to re-flash WM6.5 on it, correct? FYI, v3.14.405.2 is not the latest version. I think that v3.14.531.0 is (and the filename is RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship.exe). I suggesting looking for that (it's likely in a stickied thread in the WM6.5 sub-forum) and trying it. If that doesn't work, you might try downloading the latest radio and installing that first.
Another idea: could your USB cable be flakey, perhaps? If you have another that you can grab, try that.
If you can't manage to re-install WM6.5, try installing Android or Windows Phone 7 (see the respective sub-forums), instead. This guide can help you do it for Android, if you're interested.
Click to expand...
Click to collapse
Ty for the fast answer, I'm donwloading the ROM right now and later i will update with the results. I cannot install Radio only version because I do not have HSPL installed, and about the USB cable, I'm using it with other devices and it's working fine. (I will try to find another USB meanwhile cable just to be sure).
Update, after downloading the ROM I tried to install it via USB but the strange behavior continues, it does not pass the 0% and after some minutes the setup fails as shown in the album I posted in the first post

I'm not sure what more you can try if you want to keep WM6.5. I suppose that you could try to install HSPL, a new radio and even MagLdr, then try to install the WM6.5 ROM again. If it fails, then just install Android or WP7, I guess. I would just do that, anyways, since WM is dead. I would go with the Android 4.3 (latest version from Google) ROM that's in my signature, but it's up to you.

Osprey00 said:
I'm not sure what more you can try if you want to keep WM6.5. I suppose that you could try to install HSPL, a new radio and even MagLdr, then try to install the WM6.5 ROM again. If it fails, then just install Android or WP7, I guess. I would just do that, anyways, since WM is dead. I would go with the Android 4.3 (latest version from Google) ROM that's in my signature, but it's up to you.
Click to expand...
Click to collapse
The problem is install anything, i cannot install HSPL or anything else by USB (phone freezes at 0%), trying to install from the microSD the behavior is hanging at Searching . . .

Primordium said:
The problem is install anything, i cannot install HSPL or anything else by USB (phone freezes at 0%), trying to install from the microSD the behavior is hanging at Searching . . .
Click to expand...
Click to collapse
Are you trying to install HSPL through HD2 Toolkit, perchance? Have you tried the standalone version? A link to it is here. I would suggest right-clicking and running it as an administrator, just in case. After that, try using the HD2 Toolkit to repartition as MagLdr or CLK. If it's still a no-go, then I don't know.
OK, I just did a search and it came up with a slew of threads that possibly describe your problem. Have you looked at any/all of these and tried the suggestions in them?
[Q] HD2 freezes at 0% during update or flash
[Q] is this HD2 bricked or... need your opinion
Hd2 white screen of death
HD2 Bricked?HELP?
[Q] How to "unbrick" HD2?
HD2 stuck on custom boot screen and won't flash anything in bootloader
my htc hd2 is STUCK.. HELP ME PLS
[Q] Htc hd2 stuck on white screen
[Q] Unable to flash any ROM!
I realize that not all of them describe your situation perfectly, but the replies may still be helpful. There are a lot of things to try. I would read each of them carefully and try them all (as well as check that, the ones that you've already tried, you did the right way).