Related
Guys, I hope you can help me!
I was using my Imate Jasjar when it was accidentally bumped by another person. the Jasjar fell but it wasn't that high and the floor was carpetted. However, I noticed that whenever i try to tap on the Start button on landscape mode, the calendar application opens up! And when I try to tap V-Bar on the other corner opposite the Start button, the Contacts application opens up. Basically, the soft keys on the bottom screen are the one opening up even if I'm tapping the ones on top! If I tap the bottom soft keys, I thought the Start button or my V-bar would come out but still the Calendar and Contacts applications were the ones that opened. Basically the everything on top cannot be tapped!
On Portrait mode, I can tap the start button but when the V-Bar was tapped it still opens the Contacts application.
I went to Settings then Screen to re-align the screen. I thought it would solve the problem but apparently it didn't! I was trapped in the Align Screen section giving me an endless loop to tap the 5 areas of the screen.
I now did a Hard Reset, and now I'm forever got stucked to the Align Screen part.
What am I supposed to do??? Please help!!!
Hi,
Seen the same problem... Try to guess the error margin of the alignment...
for example instead of tapping in the center of the cross try tapping on left or right... Since your screen isn't aligned you can't press on the center...
Now the problem is hardware, not the MB but the LCD...
After tou figure out the margin error, the Universal will resume and then you ca align the screen via Start->Settings->System, align screen
I'll try to know more about this problem asking my friend.
Best of luck
thanks for your reply!
i also believe that it has something to do with the LCD. there are no cracks whatsoever. problem with the aligning is i have to keep on guessing. and if ever i do align the screen successfully, i'm not sure if re-aligning the screen in Settings would solve the problem.
i would appreciate though if your friend or anybody else can shed light to a solution.
This is a simple problem to solve ;-)
When the allign screen is ON and you have to make the first tap on the crosshair (just before you start clicking away to allign your screen), twist your display from landscape to portrait mode...
Now continue to allign it as usual, and you should finish successfully!
Cheers,
San
unfortunately, after following your instructions, i still went on an endless loop on aligning the screen. i'll try to reflash the rom and see if it would work. i hope it does...
i updated my ROM. still stuck on the alignment screen!
any more ideas?
To be honest, sounds like your screen is broke. Even if you got it to align, I doubt it would be very usable. I think you are looking at repair - if there's no visible sign of damage, you might get away with a warranty repair.
Cheers,
Steve.
Hi
Few months back i've got exactly the same problems (odd LCD behavior, impossible alignment, etc...) with an HP4700. I went to the service center and they had to replace the LCD screen. They did not charge me and take it under warranty. In my case the unit did not drop and i made it clear to them. I would suggest you go back to the service center and forget about the drop in your problem description .
Cheers,
Bruno
I had the same thing happen on a HP 3700, I did not even drop it all i did was install the Quake game for it and after a few days the screen alignment went a bit out. It was usable but definately out by about 1 cm in each direction. The unit had not been dropped. I went into the allign screen utillity and ended up in the infinite loop. The only way to fix was a new screen. But unforunately it was no longer under warranty. The screen consists of 2 separate parts the lcd and the touch screen bit. In my case the lcd had no issues just the touch screen. Very annoying but there you go.
Search your soul and do what you feel comfortable with.
Good luck
Charlie
thanks for all your replies!
i've made several searches yesterday with similar problems (even if they're using different PPC models) and they all ended up sending back their units for repair. there's even one who posted in expansys with the same exact problem!
we'll be sending it back through expansys (we got the unit from them) and hopefully get it back before the end of the month. and yes, i won't tell them that it was dropped, he he :twisted: and they won't find evidence either on the outside because there are no physical damages. what a start of the new year for me <sigh>
right now i'm back using my XDA IIi.
thanks for all your support! this is my first thread/topic in this site and it's so unfortunate that it had to be sort of a negative one. looking forward to be active more here!
Hello there
This might help (I am currently wrking with 200 PDAs so have had this a few times)
THere may be a iece of dust/biscuit crumb etc, under the edge of the casing above the screen, try using a post it note or paper and go around the casing/edge of screen, this should clear the screen of anything that may be causing this problem.
THis worked for me on the majority of non-aligning screens
HTH
DB
My story was, one day when I needed to twist the screen, it was a bit stuck so I twisted a bit harder, yes it went back. Then few days later, the mis-alignment started and since then I have been keeping to do re-alignment my screen.
My screen is mis-aligned once every 2 or 3 days or even few minutes then I have to re-align by using WM5's alignment program. It sometimes takes me 2 or 3 times or even one time.
The most anoying thing is it keeps forget after aligned screen.
Now, certainty, I don't think it is a screen problem because after running alignment app, it correctly pointed into the right spot but then it forgot where the right position was.
I have done the upgraded ROM ( even tried Ivan AKU 3.2 ROM ) but problem still persisted.
I just tried clean up the edge of screen, finger cross, hope it fixes my problem.
Bad thing is, I bought my device from UK and I am living in Australia so therefore, my warranty is definately invalid. I don't want to spend 200 AUD for the new screen ( unless I am 100% sure that LCD is faulty ).
Anyone has any idea or even a better suggestion because I don't see many people having this problem.
I suspects that maybe the flex cable got ripped but not totally ripped. Don't know , please help me out on this one
Best regards
Anyone has any idea about my problem ??
One question :
I know that the flex cable has 2 connectors ( one is for LCD display and another is for LCD function ). Now does LCD function relate to the touch screen function ? and if one tiny wire of the function cable got cracked, but not totally cracked, will it affect the touch screen function ?
Other thing, does WM5 store any setting relating to screen alignment setting ? If yes, where is it ?
Thanks
Hi, from another forum, it only help to bypass the alignement loop:
"here you go theses are simple steps to bypass the touchscreen alignment.
Install you activesyn blah blah blah when it finds it go on my computer and go into your PDA device
go to windows startup and delete the Welcome file
after that give your PPC a soft reset and BAM u by passed the screen now get a free desktop program liek pocket controller from the internet it will automatically install on your pda and BAM you can control your pda add music and whatever
but now if you want to click stuff on the road get pen irazu just search on google and send it to your PDA then go to file explorer and double click it and you got a cute little mouse program that you can use like a stylus"
also try this little soft:
http://www.codefactory.es/downloads/mobile_speak_pocket/release/MSP_RemoteAlignment.zip
Hope it helps.
MaX
Hi godtakeit!
I've had the same problem a few weeks ago (and still having it from time to time) and for me a slight (very careful) bending of the screen makes it work again. It seems to me that there are connector behind or near the display which has some loose contacts.
Did you notice any other problems which came in conjuction with the alignment problem (e.g. speaker not working)?
.ox
Hi oxident
No, I don't have problem with speaker ( it was not working before but it is because of the jack plug problem - it solved ). Yeah, I did notice if I bend the screen carefully, the problem is gone. The funny thing is when I aligned the screen, it worked but if I closed it off and left it over night, it started again when I opened the lid.
You may right about the connector between LCD screen and mainboard. Well, I have no choice but openning the device and check it up.
Also, I read the thread somewhere in this forum and somebody advised this problem maybe relates to magnet around device. My brother aslo advised me that LCD charged and reserved negative electrons. Wierd but I am experiment it at the moment ( taking off battery and leave the device for a few days so that it can release the negative electrons ).
Hope it fixes
please help
i have an imate jas jam that i i got from my father he used it for like 3 years and it is pretty banged up so i cant use the warranty and repairs cost a lot, any who i got it yesterday and it was very slow so i reset the settings and now im stuck on the align screen it keeps going on for ever and ever if any one knows any thing plzzzz help
Welcome aboard
You have one of the best HTC devices ever made!
Have a look here to locate the solution to your prob:
http://forum.xda-developers.com/showthread.php?t=549207
Post number 2
Good luck,
Hello,
I've recently been looking around online to figure out a solution to my problem and I came across this forum, I honestly had no clue of all of the things possible with this phone...
I have an At&t 8525 (in august I will have had it for a year) and just yesterday I started having problems with the touchscreen, when I would try to use the touchscreen nothing would be functional...after messing around on the screen I found out that the lower right hand corner of the screen (the right hand corner when the keyboard is in use) pulls up the start menu...although the touchscreen didn't work the phone itself still did, I could access the start menu and other actions on the phone by pushing the soft keys...
This morning I started toying with my phone again and it worked normally for some time and then eventually the screen started to do the same as it was doing before...so thinking that the problem was a virus or something, I figured I would reinstall wm6 back onto the phone hoping that it'd restore everything to normal...now I'm stuck on the 'welcome to windows mobile green screen' and only once have I gotten to the 'align screen'...
I truly don't know what or how to fix this problem with my touchscreen and I'm really new to all of these phone experiences...(I'm pretty sure returning the phone is out of the question)
So any help given would be very much apriciated,
-Ben
benman715 said:
Hello,
I've recently been looking around online to figure out a solution to my problem and I came across this forum, I honestly had no clue of all of the things possible with this phone...
I have an At&t 8525 (in august I will have had it for a year) and just yesterday I started having problems with the touchscreen, when I would try to use the touchscreen nothing would be functional...after messing around on the screen I found out that the lower right hand corner of the screen (the right hand corner when the keyboard is in use) pulls up the start menu...although the touchscreen didn't work the phone itself still did, I could access the start menu and other actions on the phone by pushing the soft keys...
This morning I started toying with my phone again and it worked normally for some time and then eventually the screen started to do the same as it was doing before...so thinking that the problem was a virus or something, I figured I would reinstall wm6 back onto the phone hoping that it'd restore everything to normal...now I'm stuck on the 'welcome to windows mobile green screen' and only once have I gotten to the 'align screen'...
I truly don't know what or how to fix this problem with my touchscreen and I'm really new to all of these phone experiences...(I'm pretty sure returning the phone is out of the question)
So any help given would be very much apriciated,
-Ben
Click to expand...
Click to collapse
This is a loose connection between the main .. device and the touch screen . There is this cable that connects the screen and the keypad .. that has a loose contact. press the screen and the keypad together and the touch sreen should start working again . i had this same issue i don't know how to fix it.
Sounds like this problem here:
http://forum.xda-developers.com/showthread.php?t=288233
The above is an old thread. You can try the old business card trick (though it's by no means guaranteed to work). You could try a dis-assembly and reconstruction, double checking connections - particularly the screen to d-pad connection.
The Hermes unlike the Kaiser is very prone to this kind of problem and despite the threads you may see, guaranteeing a fix, I don't believe there is one fix for this problem. This is because there are several variables that can cause the problem and it just depends whether your case is caused by:
Dust trapped under the bezel
A loose connector - possibly d/pad to screen
A failed capacitor on d/pad or main board
Another failed component
Digitizer coming unglued from LCD
etc
Mike
Had the same problem right before EVERYTHING went white. Replaced the lcd altogether, about $110Aud on ebay, and everthing works great again.
Cheers....
Hi guys!
Long time no post!
I hope you can help point me in the right direction.
Two things started happening with my 8525 TyTN, rendering it unusable. I do have a backup one, so it's no panic. But I would LOVE to try to repair this.
Here's what happens!
1 - The two LEDs in front don't work! No green; no blue; no amber. (HOWEVER, When I first replaced the battery after a hard reset, I did see is glow red for a second!)
2 - None of the buttons on the front work! None. Start/End, the D-pad, mail, internet explorer. All dead!
Interestingly enough... the LCD screen is perfect, as is the touch screen.
The unit also works perfectly fine.
I did a Hard Reset.
I am using WM6.0.
I am wondering... PERHAPS there is some kind of ZIF cable that goes from the body to the top panel? MAYBE that came loose?
If you have seen inside your TyTN, is there one cable/ribbon for lights/buttons?
If so, that would explain it!
If there are two cables/ribbons.... one for lights, one for buttons, then the odds of them BOTH falling out are near impossible!
I would LOVE to hear any ideas or thoughts!!!
Thanks as always!!!!!
Mike
Hello and welcome to a new phone!
I have a similar problem, mine sometimes gets a white screen and the D-pad buttons rarely work for long.
It is quite possibly a loose ribbon cable.
There is actually a thread here about this issue - just do a search for 'white screen' or similar and you'll find it. It was posted to within the week so shouldn't be far from the top if you browse for it, but I can't remember which Herme's category it was in.
There's even a full guide with pics to pulling your 8525 apart!
Cheers! Oggy. ó¿ó
try a new rom,.
I have the same problem. I thought it was bcs my TyTN fell down once. It started with Iexplorer always popping up when I wanted to do something. I thought the IE button at the top was stuck or something and when I pressed hard on the message button everything was okay. All buttons worked. But after a few days they stopped working and pushing the message button wont work also. And both the red and green call button leds are always shining. It sometimes happens that the dpad works for a second and than nothing.
I used the original wm5 and flashed to 6.1 now, no change tho.
it's not the rom, tried several roms now
for me it's just the call answer button, but this is annoying enough
there are some topics in the hermes section which describe the problems you encounter or even worse problems (the lcd flickering or just giving you a bright shining white) and they all say it is a loose cable connector right under your dpad
some of them opened their tytn (guarante already gone) and put some sort of paper or rubber or sth else on the connector.
other say tighten or loosen the screews worked for them, but none of the solutions seem to be final, it always works for some time.
if you have still guarantee i would try sending back or try somewhere else a repair, that is what i will do with tytn
i hope i do not have to pay for the repair
good luck
Loose screw
I was able to fix this problem after ATT told me that I was out of warrenty and it was going to cost 499.00 for a new phone.
I it turn out it is a loose screw on the inside and to get to it you have to undue 11 screw to get to it. I might be able to fix it for you. I dought you would be able to get into this phone and not hurt any of the other functions.
Rick
Hi,
could you advise how you managed to fix it?
Thanks.
button failure and white screen
I have the same problems, if I turn off and on for 3/4 times everything back to normal. But is really annoying because I miss calls.
To me seems a software issue.... I can solve it by turning off the screen does not make sense hardware problems
have a look to this post:
http://forum.xda-developers.com/showthread.php?t=435281
I have still to test the suggestion of schaps advance config version 2.02.1.0.0
Sorry it not a software issue and you can flash a 100 roms and it still won't work. You simply have a bad flex cable and possibly a defective dpad circuit board. You have to crack open the phone to replace it and it has to be carefully done. There are tons of DIY's about opening the phone and replacing the cable. There are even YouTube Videos about it.
touchscreen was working today morning, took battery out for 2 hours, turned it back on and it was working abit weird, and now i cant press any touchscreen buttons atall!
So no softkeys (pick call, home etc.) and nothining on the big screen! I can turn on the phone, press the power button and volume buttons, see my home screen get calls etc.. hard reset twice, took battery out, nothing does it .. gonna try flash it but dont think itll do it ... and ideas?
Im in uk aswell if that makes a diff
Dear All,
I have similar problem. Usuallí I use on my HD NRG ROM. About 3 weeks ago I updated to the latest NRG WM 6.5 23xxx ROM with Sense 2.5 Maxmanila version, and since this upgrade the touch screen position moving randomized up or down from 2 mm to 30mm!!! After this ROM I tryed updating each newer version, but not changed nothing. I need realign the screen about 10 times / day!!! The phone I never dropped or cracked.
Can help me somebody what happened with my HD?
I had this happen to me yesterday. I was surfing on my phone as per the norm. Put my phone down. Got a txt, picked it up and it wouldnt allow me to access it. I thought it must be a freeze as it has happened occasionally.
So I restarted.............and nothing. No response AT ALL from the touch screen.
I have noticed the oily spot problem on the most part of my screen, and thescreen doesnt have that little give it used to when using it (paranoia possibly)
So I can only assume something has given within the screen. Ive been searching all day on the internet for causes and fixes but nothing has come up.
The volume and power buttons work but I cant do anything at all with the phone as its obviously all touch based.
Is this a screen replacement job then or is the whole phone goosed?
Roheelshah if you turn your phone off do you have the massive oily screen thing?
Any help is most appreciated....
I had the same thing, a oily spot, but it was there for months, then i noticed another new spot (looked like a tiny tiny burn) and thats when it stopped working completely... ive ordered a new screen which should be comming in a few days, im hoping thats the issue
will let you know if it works ....
keep me updated if you find anything
thanks!
NECROSTONE said:
I had this happen to me yesterday. I was surfing on my phone as per the norm. Put my phone down. Got a txt, picked it up and it wouldnt allow me to access it. I thought it must be a freeze as it has happened occasionally.
So I restarted.............and nothing. No response AT ALL from the touch screen.
I have noticed the oily spot problem on the most part of my screen, and thescreen doesnt have that little give it used to when using it (paranoia possibly)
So I can only assume something has given within the screen. Ive been searching all day on the internet for causes and fixes but nothing has come up.
The volume and power buttons work but I cant do anything at all with the phone as its obviously all touch based.
Is this a screen replacement job then or is the whole phone goosed?
Roheelshah if you turn your phone off do you have the massive oily screen thing?
Any help is most appreciated....
Click to expand...
Click to collapse
download and install this _HTC Touch HD_TouchHD system.exe
BOLDESH said:
download and install this _HTC Touch HD_TouchHD system.exe
Click to expand...
Click to collapse
whats it do? and where from??
I just posted something like this a few days ago, pulled my phone out and screen wouldnt respond, had these marks all over my screen, "swirly marks" as i describe it, very well could be the oily marks you are talking about. you can move them around with your finger right?
anyway, i took my sim out, tryna find a spare phone, couple hours later the marks were gone and screen started working again, touch wood its been fine since.
no idea what happened, but try letting it air out or something
ok basically i received a new digitizer today (the actual touchscreen) ...
i dismantled the whole phone using the service manual and some video some guy made (VERY HELPFUL, if anyone wants it for any reason i can post a link), ok so i got rid of all the top bits, the circuit boards (or watever theyre called)
I got down to just the bezel, lcd and digitizer (dont know what a bezel is, the lcd is where the display actually is and digitizer is directly stuck ontop of that)
Apparently when replacing the screen, htc have made it so that you have to replace all three of those parts instead of individual ones, but you can buy them seperately so i thought i'd hero it.
i poked out the screen from the frame (some chewingum like stuff holding it in) then i started peeling off the digitizer (if you get one and want to try it you'll know where to peel) ... this was a mistake tho cause the lcd is unbelievebly sensitive so while peeling off it left scratches on the lcd, and me not knowing the lcd is sticky tried to wipe them and use a dust free cloth, which left alot of crap on the actual lcd!
i managed to get the digitizer off and ripped the cable that goes from digitizer to whatever reads our fingers on the screen, took it all off, placed the new one directly ontop and fed the wire exactly how it was for the first screen.
Put it all together again
Now I did mess up my screen badly, but in a good way! .. i now have full touchscreen working (smoother than ever) but my LCD display is near enough gone, so it looks like the screens really really dark, and i have to tilt it at certain angles to see the screen..
After all of this i now have a touch hd i can controll from my pc (using mymobiler) so i can recieve calls, send texts all from my pc when connected thru active sync, can even play teeter ... but not really the same!
I wouldnt recomend anyone to try what i did, although i think its worth the risk as I would have to replace the lcd anyways if i wanted a new screen in the first place... and who knows you might be able to peel the digitizer off clean (NEVER EVER EVER TOUCH LCD WITH ANYTHING!!!).
It all cost me around 10-15£ for the digitizer and screwdrivers and alot of hours dismantling phone compared to 50-100£ for a new lcd.
I am either going to get a new lcd now so i can actually see the screen, or get a new phone.
Sorry for the essay but hopefully this helps someone in any similar situation
if i do get a new lcd will post how it goes and if it sorts out everything
if anyone knows of any other reasons why my lcd would be so dim (brightness is 100%) accept for me getting carried away with it ... help would be appreciated
the_cool said:
I just posted something like this a few days ago, pulled my phone out and screen wouldnt respond, had these marks all over my screen, "swirly marks" as i describe it, very well could be the oily marks you are talking about. you can move them around with your finger right?
anyway, i took my sim out, tryna find a spare phone, couple hours later the marks were gone and screen started working again, touch wood its been fine since.
no idea what happened, but try letting it air out or something
Click to expand...
Click to collapse
Yeah swirly oil marks is how myne started ... i think i finished off the screen by trying to press hard on the mark to try and clear it .. . so be careful with it.. but think that overall the screen had seen better days (course only a few weeks after warrenty finishes) ... all conections inside were ok aswell
doczyus said:
Dear All,
I have similar problem. Usuallí I use on my HD NRG ROM. About 3 weeks ago I updated to the latest NRG WM 6.5 23xxx ROM with Sense 2.5 Maxmanila version, and since this upgrade the touch screen position moving randomized up or down from 2 mm to 30mm!!! After this ROM I tryed updating each newer version, but not changed nothing. I need realign the screen about 10 times / day!!! The phone I never dropped or cracked.
Can help me somebody what happened with my HD?
Click to expand...
Click to collapse
Same here. Touch screen not working. Phone never flashed, droped,...
Any solution?
unfortunately, a friend of mine changed the touchscreen without success. Phone was in perfect state, no drop, no flash. Just the touch not responding. I'm not sure that changing whole part lcd+digitizer solve the problem.
Hi all!
I've got similar problem with my touch HD. It's stock since I bought it. My touch sense was acting weird, like it wasn't properly calibrated. Like, when I press 7 on phone pad, the phone actually presses 1, and if I press 0, phone presses 5 and so on..
I've tried to align the screen, but it doesn't get aligned the first time. I have to repeat the process about 4 times before it gets aligned. That's good for about few minutes and the problem is back. Hard reset was also done, 2 times.
Could this be a fixed with a software update? Does this mean that digitizer will soon be dead?
Thank you for your help
Regards
igothtc2 said:
Hi all!
I've got similar problem with my touch HD. It's stock since I bought it. My touch sense was acting weird, like it wasn't properly calibrated. Like, when I press 7 on phone pad, the phone actually presses 1, and if I press 0, phone presses 5 and so on..
I've tried to align the screen, but it doesn't get aligned the first time. I have to repeat the process about 4 times before it gets aligned. That's good for about few minutes and the problem is back. Hard reset was also done, 2 times.
Could this be a fixed with a software update? Does this mean that digitizer will soon be dead?
Thank you for your help
Regards
Click to expand...
Click to collapse
use ScreenCal to fix it, hopefully it can help you
Hakim Rahman said:
use ScreenCal to fix it, hopefully it can help you
Click to expand...
Click to collapse
Hi!
I've successfuly installed the cab file on my phone's sd card, but the problem is still there. I don't know where the installed files are, do I have to run this application?
Thank you for your help!
Regards
igothtc2 said:
Hi!
I've successfuly installed the cab file on my phone's sd card, but the problem is still there. I don't know where the installed files are, do I have to run this application?
Thank you for your help!
Regards
Click to expand...
Click to collapse
have you hard reset the device after installing the cab file ?? if not do it and see if there are changes...
Hakim Rahman said:
have you hard reset the device after installing the cab file ?? if not do it and see if there are changes...
Click to expand...
Click to collapse
Just did the hard reset. When it asked me to align the screen, I just couldn't align the top left corner. I had to press it like 50 times before cross went to the lower corner. Otherwise, after the align it's good for about couple of seconds and then it's just pressing all over.
I thought I had just some software issues because the screen wasn't dead, it responded to my touch. So, I'll probably have to buy a new screen and digitizer, right? Or do you have any other ideas?
Thank you again for your help!
Regards
firstly screencal installs calibration settings not for blackstone so do not install it, no point. (btw it also increases device touch sensitivity)
secondly you guys should try and install the calibration settings for blackstone, basicly what the align screen does, not sure where to find them for download but i could post the registrys if someone wants to make a .cab from them. (atm i cba making the .cab but i am able to do it )
if the calibration settings do not work i think it is best to buy a new lcd package (or buy new device and give me old one for spares oj)
Rn
hi buddy ! What you mean GSensorCalibrator ??
i didnt mention anything about gsensor calibration dude.
tried and tested screencal the other week and it screwed my blackstone.
install these instead:
*screen calibration, sets the blackstone touch points: (aligning the screen)
if you install a cab with these registrys it should fix the alignment problem.
(if it doesnt then its hardware issue = lcd etc)
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\TOUCH]
"MaxCalError"=dword:8
"CalibrationData"="511,542 183,881 183,198 834,197 833,880"
*this one will maximise the touch sensitivity for those that want it:
[HKEY_LOCAL_MACHINE\Drivers\TouchPanel]
"PressureThreshold"=dword:0
Rn
Does anyone have a recommendation where you can buy a digitizer and lcd from?
Hi all,
My trusty blackstone has begin letting me down and I don't know if flashing a new rom will help, or if it is something physical that is breaking / broken. I'm using the Stonehenge ROM with CHT and everything has been fine for months.
Recently the touch screen allignment just seems to 'wander' sometimes just a little, other times quite a lot (so much that using the fake hardware buttons at the bottom of the phone, brings up the start menu). This means that intermittently I cannot answer calls, and typing a message on the SIP is an absolute nightmare!
The start menu icons do not seem to be as affected as the home screen and CHT, and I can quite easily get to the phone settings and recalibrate the screen - this will help for a short while but the alignment drifts again.
Restarting the phone has a temporary positive effect but it doesn't last.
Anyone else experienced this?
I have exactly the same problem.
Dissembled the whole device, blown some hot air but didn't help. Seems it's a HW fault. But I have a doubt whether the problem is in digitizer or in control board.
It's definitely one of the more frustrating problems that I've ever had with the phone.
I might try flash a new ROM then give up if that doesn't work. At least I won't be tempted to disassemble as it has already been tried, tbh I'd have just tried the tin of compressed air too, I don't trust my soldering skills for tiny electronics.
It is getting progressively worse, the touch area of the screen has slipped so low now that I can't use half the screen.
Screen Alignment Fix
Have a look on this one, maybe this will help you...http://forum.xda-developers.com/showthread.php?t=538113