--**Here's a method to get the Epic flashed to cricket with internet and apps***--
***Edit- I cleaned up my post and attached a good PRL to use (42700) and "ConnectBot.apk". I also believe I have MMS sorted out. I'm gonna double check everything later tonight to make sure there's no issues and I'll update my post accordingly.
---Requirements---
*Download and install Qpst. 2.7 build 355
*Download and install normal Epic 4g drivers.
*Cricket prl. (42700 PRL is what I recommend. I've attached it to my post)
*USB Cable
*Your MSL.(I attached connectbot to my post in case you need it)
_________________________
---Getting your MSL---
-If you know your MSL already you can skip this part and start at the "Getting started and setting up QPST".
1. Find and install "Connectbot" found in the market or at the bottom of my post.
2. Select the dropdown box on the bottom left that says "SSH", and choose "local". Put whatever you'd like in the nickname box and hit "enter".
3. Click on "Android".
4. Use the command "getprop ril.MSL" and hit "enter".
5. Your MSL should now be displayed.
...If that doesnt work...
1.Type "getprop" instead.
2. It should show a long list, scroll down to the section that starts with "ril".
3. You should see "ril.msl", the 6 digit MSL number will be after that.
---Getting started and setting up QPST---
1. Plug in your phone to your computer and when prompted to choose between "Charging, mass storage, or tethered modem", choose "Tethered modem", then choose "3g modem".
2. Open up QPST > "QPST Configuration". Click on the "Add new port" on the bottom right. Uncheck mark the "Show serial and USB ports only". In the box above it, you should see your phone connected and the corresponding COM port. Select it and the "Port" and "Port label" will autofill. Hit "Ok".
3. Open up QPST > Service programming. Select your phone in the "Select an active phone" box.
Click on "Read from phone" and enter your SPC when prompted.
***(Note: If you are having trouble with QPST recognizing your phone, instead of using the "Tethered modem" method when plugging in your phone, dial ##8778# and switch both the "UART" and "USB" options to "MODEM". QPST should then see your phone. Revert the "MODEM" option in the previous menu to "PDA" when done.)
---For talk/text---
1. You will first write a new prl to your phone. Cricket prl 42700 is preferred.
2. Click on the "Roam tab at the top.
3. Click on the "browse" button under "Preferred roaming" and locate the prl file you wish to write.
4. Click on "Write to phone".
5. Let QPST do it's thing and voila, your new PRL will be written to your phone.
---For internet---
1. Click the "M.IP" tab (may be "M.IPv6") and set "Mobile IP Behavior" as "MOB + Simp".
Select any profiles listed under "user profiles" and click edit. Do the following for all profiles:
Make sure that "profile enabled" is checked and enter in the following:
NAI: [email protected]
Tethered NAI: [email protected]
2. Change "home address", "primary ha", and "secondary HA" to all zeros.
3. On both "HA Shared" and "AAA Shared Secret, select the "enter text string" and type in the following password (all lower case): "cricket".
4. Click "Ok".
5. Set active user as "0".
6. Click "PPP Config".
7. Click the "Um" Button.
8. Under user ID enter: [email protected] as well as for tethered NAI. If a text box is black with red lines in it, click it and press ctrl + D. Enter "cricket" in the password box.
9.Click the "AN" Button and repeat the last step.
10. Click "write to phone"...After that, you should now have the 3g icon on your phone.
11. Last step to get internet and apps working, if you're already activated on cricket, is to call customer service and have them switch you to the 55 dollar Android plan.
_________________________
*Please note: They have a 55 dollar "All-in" plan, as well as the $55 Android one. So make sure you're put on the right one. I've had most luck by asking to speak with the "Smartphone department" and then requesting them to have my equipment and plan changed.
**Thanks to anderdroid for testing Android plan with fascinate.
Hope this helps! PM me if you need a download link for QPST.
how would if you do it using QPST?
I am still waiting for mine to arrive but I always use QPST to inject to other networks and unlock the EVDO
wait for further infomation, because i want to use it in China, where the carrier situation is a little complicated.
cdma isn't carrier locked, if its the same frequency then you should se if cricket will flash it for u
cricket flash
do ##8778# and select modem to get com port, samsung default 16 digit password, write prl, and done. for talk and text
kc720 said:
do ##8778# and select modem to get com port, samsung default 16 digit password, write prl, and done. for talk and text
Click to expand...
Click to collapse
what is samsung default 16 digit password? Where I could find the password for my samsung epic 4G. If some one could help me I will donate. thanks
kc720 said:
do ##8778# and select modem to get com port, samsung default 16 digit password, write prl, and done. for talk and text
Click to expand...
Click to collapse
Alternatively...you can install the regular Epic drivers and plug in the phone...when given the three choice prompt, choose "tethered modem"...then select 3G tether. The phone will then connect on a COM port and you can then connect to your phone using CDMA Workshop, QPST, or whichever programming tool you prefer and flash the prl that way. I'm still working on getting the data up and running.
cineung02 said:
what is samsung default 16 digit password? Where I could find the password for my samsung epic 4G. If some one could help me I will donate. thanks
Click to expand...
Click to collapse
Default 16 digit should be 01F2030F5F678FF9, give it a try. You can also use CDMA Workshop to read and change your Epic's SPC, which is the way I prefer.
So, quick question, do I need a specifically modded rom to run my Epic on Cricket, or is it that I can use any rom and then flash the phone??? I'd like to know this because I bought the phone off contract and would like to use it on Cricket. -thanks
dcorn619 said:
So, quick question, do I need a specifically modded rom to run my Epic on Cricket, or is it that I can use any rom and then flash the phone??? I'd like to know this because I bought the phone off contract and would like to use it on Cricket. -thanks
Click to expand...
Click to collapse
Nope, doesn't need to be any specific rom. It can be whichever one, even the stock one.
Sick!!! this makes my life so much easier thanks!
I finally managed to write AN data parameter for EV-DO, using QPST 2.7 build 355, other version wont write the ev-do parameter. Data is ON now for my network.
This is only because my carrier using simple IP, I believe cricket is using a mobile IP, so the case might be different.
Well, I'm kinda new at this flashing business and my contract with my gsm provider has been over. I just wanted to transfer my number onto my new epic 4g on cricket but so far I haven't found a dealer who can do it, can anyone help me out, maybe post a tutorial or guide, it would be hugely appreciated
dcorn619 said:
Well, I'm kinda new at this flashing business and my contract with my gsm provider has been over. I just wanted to transfer my number onto my new epic 4g on cricket but so far I haven't found a dealer who can do it, can anyone help me out, maybe post a tutorial or guide, it would be hugely appreciated
Click to expand...
Click to collapse
Assuming you have your MSL...
-Requirements
*Download and install Qpst. 2.7 build 355
*Download and install normal Epic 4g drivers.
-Plug in your phone to your computer and when prompted to choose between "Charging, mass storage, or tethered modem", choose "Tethered modem", then choose "3g modem".
-Open up QPST > Service programming. Select your phone in the "Select an active phone" box and click on "Read from phone" and enter your SPC when prompted.
For talk/text
1. Write a cricket prl using the "roam" tab, Cricket prl 32100 is preferred.
2. Click on "browse" and locate the prl file and then click on "write to phone".
For internet
1. Click M.IP (may be M.IPv6 and set Mobile IP Behavior as MOB + Simp.
Select any profiles listed under user profiles and click edit. Do the following for all profiles.
Make sure that "profile enabled" is checked and enter in the following:
NAI: [email protected]
Tethered NAI: [email protected]
2. Change home address, primary ha, and secondary HA to all zeros.
3. On both HA Shared and AAA Shared Secret, click enter text string and type in the following password (all lower case): cricket
4. click ok
5. Set active user a 0.
6. Click PPP Config
7. The "Um" Button
8. Under user ID enter [email protected] as well as or tethered NAI. If a text box is black with red lines in it, click it and press ctrl D. Enter cricket in the password box.
9.Click "AN" Button and repeat the last step.
10. Click "write to phone"...After that, you should now have the 3g icon on your phone.
11. Last step to get internet and apps working, if you're already activated on cricket, is to call customer service and have them switch you to the 55 dollar Zio android plan. They have a 55 dollar "All-in" plan, as well as the zio one. So make sure you're put on the right one.
I made this in a hurry, but I believe I got everything.
**thanks to anderdroid for testing Zio plan with fascinate.
***Edit- Since I'm a new member, it wouldn't let me post the links to the downloads of Qpst and the 32100 cricket PRL. PM me if you need either.
Now if there was a way to make sprint think this was a Hero and not an Epic then we could avoid the $10 charge. That's the only real reason I have went back to the Hero.
Wow, great guide, thanks! Just a couple o more questions, sorry. Where one has to input the 10 digit cricket number it is assuming then that you have an account already and that you'll be moving to 55 dollar plan in order to achieve that change to 3g enabled correct?
dcorn619 said:
Wow, great guide, thanks! Just a couple o more questions, sorry. Where one has to input the 10 digit cricket number it is assuming then that you have an account already and that you'll be moving to 55 dollar plan in order to achieve that change to 3g enabled correct?
Click to expand...
Click to collapse
No problem, but to answer your question...yes, it is assuming that. You can get your account set up first and flash the text/talk portion using the steps above and once that's done, you can get the internet set up and working...
Perfect, thanks! :]
If anyone would like screen dumps I can do this... There were a couple of steps I needed to do to connect.
Thanks for the help everyone!
EDIT:
Rock on... Got data now! I had to do this all because my wife and I are going through a divorce. I purchased the phone, but it was on her account. Well she decided to turn it off, and I remembered hearing about how everyone changed their phone over to Cricket...
The store that I started my Cricket service with gave me the all in 55 plan. Had to make a call tonight to get it changed. Nothing happened after the first call and after the second call I asked if there was anything I needed to do. He told me to dial *228 talk and then it would reboot itself. I was hesitant because I thought this might be standard operating procedure for just the Zio. I dialed it and listened to the message. Then it hung up and a pop up screen said CDMA call dropped. There was an X inside of a circle next to the signal bars. I finally rebooted it and then the data worked.
I got the MSL by using ConnectBot from the market and followed this procedure, logging in local (bottom left drop down menu), typing a random username, connecting, and using the "getprop" command.
What will we have to do to get the Froyo update though?
I need those couple extra steps to connect since I'm having trouble getting the phone recognized by QPST please
Open QPST Configuration > Ports > Add New Port (you may have to uncheck Show Serial and USB....)
If you can't locate the port based on the results then go into your Device Manager on your computer. Check under COM ports there to see what your Samsung is under. After you add this port then you should be able to use QPST Service Programmer.
Uh another cool thing is that I can use the Sprint Hotspot utility. I took the security off and it works. 3g hotspot for free and without root.
1043kb down 150kb up, w/ 2-3 bars
Related
Hi,
I recieved a rogers samsung focus today.
Inserted my bell sim card, and booted. was asked for a code, i entered an unlock code i got and it was accepted.
I can send and receieve calls and text msgs, however i can not get an data on the phone, via web browser, live hotmail, or xbox app.
I accessed the diag app via ##634#, however when i try enter the root menu (*#197328640#) nothing happens
I suspect the issue is the network profile is not set to auto, and rogers manuelly configured the phone with there xml profile.
with the LG wp7 device i was using yesterday i could "SET ADC" :enable" or "set network profile", via the ##634# menu => factory menu => engineer menu => other settings
anyone have any suggestions?
apn
in settings add bells apn and it should work fine, stay out of the diagnostic menu, there shouldn't be anything there to change, I can't remeber where in settings it is but there is a spot to add an apn,
WOW that was pretty easy.
APN location: settings/cellular/add APN
Bell lists the info on their site, for reference the APN settings are;
APN: pda.bell.ca
Proxy server: web.wireless.bell.ca
Port: 80
I've added the APN to the focus and browsing and xbox live work, i wonder if adding the proxy server would make things faster/better signal? and if so, how?
On another note, when i renegotiated my plan last week MMS was added, and i was using it on my LG WP7 Device. How do i change the MMS setting on the focus?
From bell's site;
Enter the following in the Message Centre/MMS gateway field:
MMSC URL: htp://mms.bell.ca/mms/wapenc
I'm on Bell and thinking about getting a focus as well.
How is it? Is everything working correctly?
How do you go about getting an unlock code?
1. Go to the phone app
2. Dial ##634# and click Send
3. When prompted for a password type 277634#*#
4. You should now be at "Factory Menu"
5. Choose "Engineer Menu"
6. Choose "Other Setting"
7. Verify that "Set ADC" is set to Enable
8. From the "Other Setting" page, choose "Set network profile"
9. You should now be on the "Set network profile" page and in the bottom half of the window you should see a list of *.xml files. These appear to be the network configuration files.
10. Look at the filenames for the config files and take your best guess at which one to choose for your provider. I'm on AT&T and I fixed the MMS problem by choosing "_PROV_ATT_US_310_410.xml"
After you choose that *.xml profile, your MMS should be working."
The changes they are making are the ones to change the MMS capability as this can be carrier locked – outside of the phone lock/unlock status.
greener88 said:
I'm on Bell and thinking about getting a focus as well.
How is it? Is everything working correctly?
How do you go about getting an unlock code?
Click to expand...
Click to collapse
I got my unlock code through a local cellphone shop (gave him the IMBI #), downtown london(ont), not sure where he got it from, seems to have worked.
I can call and recieve text msgs but data is a bit of an issue.
You have to add APN for bell (proxy server would make things speed up unboudtably but no field for it).
It almost feel like you have to push or send a signal for data to turn on / start. usually the first time i try a webpage or bing search it doesn't work, get error " no network or wi-fi"
in terms of phone i like it better then LG optimum bell offers (had it for a week). didn't like the slide out keyboard, typing # was a pain (virtual keyboard pretty got and auto correct awesome). Also, larger screen and significantly lighter. Colours are more vivid as well, green is green not some yellow derivative.
be warned though, many many things that are lacking, january update will be interesting.
*****just tried sending picture txt no luck.....******
------- hopefully someone will figure out how to access the focus profile xml
on a side note:
after many many speedtests in London, Ont, and Hamilton,Ont; DL speed on bell caped at 3 mbps. (tests were on both LG optimum and SAMSUNG Focus)
I suspect that the $10 fee, Bell will be introducing in the next few weeks shale be to increase speed beyond this.
http://mobilesyrup.com/2010/10/18/bell-charging-an-extra-10month-for-upcoming-hspa-devices/
ManicDVLN said:
1. Go to the phone app
2. Dial ##634# and click Send
3. When prompted for a password type 277634#*#
4. You should now be at "Factory Menu"
5. Choose "Engineer Menu"
6. Choose "Other Setting"
7. Verify that "Set ADC" is set to Enable
8. From the "Other Setting" page, choose "Set network profile"
9. You should now be on the "Set network profile" page and in the bottom half of the window you should see a list of *.xml files. These appear to be the network configuration files.
10. Look at the filenames for the config files and take your best guess at which one to choose for your provider. I'm on AT&T and I fixed the MMS problem by choosing "_PROV_ATT_US_310_410.xml"
After you choose that *.xml profile, your MMS should be working."
The changes they are making are the ones to change the MMS capability as this can be carrier locked – outside of the phone lock/unlock status.
Click to expand...
Click to collapse
##634# on a focus brings up a different menu "diag" not "MFG"
anyone have any other ideas?
I live in London and have a Samsung focus to, can u tell me where is this shop?
Update?
Hey Reaver_Shadow, did you ever get your MMS to work on your phone?
ManicDVLN said:
1. Go to the phone app
2. Dial ##634# and click Send
3. When prompted for a password type 277634#*#
4. You should now be at "Factory Menu"
Click to expand...
Click to collapse
No dice - 277634#*# does nothing at the diagnostics menu. It just sits there looking at me. Are you sure this is the correct code?
the 277634#*# is for the LG MGF "app" you get installed when you dial ##634# on an LG WP7 phone it doesn't work on a samsung device. It doesn't work on mine, and i have yet to see anyne state that it works on theres.
The closest thing is a "app" that gets installed when you dial ##634# called "diag"
try entering in the diag program (found either by app menu or dialing ##634# again):
*#197328640#
and see if it works or just sits there and stares
Yeah still my biggest problem is MMS settings in the phone. Does anyone get a 3G+ symbol on the signal menu? Trying to understand why it doesnt say if HSPA is connected or not...
jessiethe3rd said:
Yeah still my biggest problem is MMS settings in the phone. Does anyone get a 3G+ symbol on the signal menu? Trying to understand why it doesnt say if HSPA is connected or not...
Click to expand...
Click to collapse
Yeah I get it all the time when downloading dada, wether its in the market place, emails or netflix...!
as for the data. I was having trouble too, then went into Settings>cellular>add APN>
and I noticed that when I was searching for a network there, it was coming up scan unsuccessful. So I deleted my APN, and scanned again, found the right network, which for me was EINSTEIN HOME, (IN WIS USA) and added internet.air.net with no password or username and now apparently Im on the data network.
Great! Now the Focus and the Quantum I have are data ready, just looking further into the MMS settings. Thanks to a link I found on here, I have the registry key that the settings are in, but unlike windows, I cant just type regedit and change the settings, so trying to find a windows phone 7 regeditor to change that and all set. Will post if I find one. Thanks again guys. ohh and I saw someone is on this, (the MMS settings already, if I see a solution there too Ill post it as well. Good luck!
I got it to work on my Focus Bell Canada using the following thread:
http://forum.xda-developers.com/showthread.php?t=924497
Very very happy
The instructions posted for tethering the Samsung Focus in the US with AT&T work mostly fine with Rogers -- use the following for Win 7 64-bit:
1) install the Samsung drivers (the multiupload url is in the other thread, the I don't have permission to post URLs, but the multiupload.com code is F52Z66IIEI)
2) open your phone and dial ##634# then press call
3) dial *#7284# and select "modem, tethered call"
4) the phone will reboot
5) plug in the phone and allow the installation of drivers
6) once the drivers are installed, select "device manager" in windows, choose "modems" and right-click "SAMSUNG Mobile Modem" and select "properties"
7) under the advanced tab enter the following under "Extra initialization commands":
AT+CGDCONT=1,"IP","rogers-core-appl1.apn"
(note that if that apn address doesn't work you can also try internet.com as an alternative)
8) under the "network and sharing center" on the control panel choose "set up a new connection or network", then "set up a dial-up connection"
9) the phone number is *99# and the username is wapuser and the password is wap
As always TWFM, YMMV.
Good luck.
Does anyone know what the settings would be for Telus?
Yes..Telus
Where the hell are you guys even getting the focus in Canada >.>. Every rogers store I've called has not gotten it yet >.>.
Se4nH4x:
I ordered it from the Roger's website -- I had to dig around, but if you go to rogers.com and type "focus" in the search box on the top right, the first link will let you order it. I ordered it on Friday and got it Wednesday. It's amazing how difficult they seem to be making it to purchase.
geological1:
For Telus, try:
phone number: #777
username and password -- leave blank
And don't put anything in the "extra initialization commands" section described for Rogers above.
If that doesn't work try signing up for a username and password at secure (dot) telusmobility (dot) com (slash) ccp. Remember to use https and not http -- http won't work. Click on register to sign up. I've heard you should use an alphanumeric username / password, without spaces, and then wait for e-mail confirmation from Telus.
Good luck.
OK Thanks a bunch.
i will try those settings later.
You can only order the Focus from Rogers online right now..that is correct.
Stores should have them by the end of the month.
For unlock just go to Ebay and search "rogers samsung focus"
What about the setting for FIDO ? I am selling an HTC HD7 and getting a Focus so I get my 3G speed back. Would really like to tether with Focus on FIDO network.
has somebody thether in Costa Rica with ICE's network
has somebody thether in Costa Rica with ICE's network
I can't make my Focus thether... I don't know what number to dial...
okay here's what worked for me for FIDO. Use ramrandhawa instructions as above with these mods:
7) under the advanced tab enter the following under "Extra initialization commands":
AT+CGDCONT=1,"IP","fido-core-appl1.apn"
8) under the "network and sharing center" on the control panel choose "set up a new connection or network", then "set up a dial-up connection"
9) the phone number is *99# and the username is fido and the password is fido
I used this with 32 Bit Vista OS and I am typing this on my laptop now and tethered to the phone. If you see this post then it's working !
Your Milage May Very. I am not responsible for damage. Educational use only.
And so far so good... will keep everyone updated if issues arise.
FOR TELUS
1) open your phone and dial ##634# then press call
2) dial *#7284# and select "modem, tethered call"
3) the phone will reboot
4) Now connect the Samsung Focus to the computer, using an USB cable, and wait until the drivers are being installed.
5) once the drivers are installed, select "device manager" in windows, choose "modems" and right-click "SAMSUNG Mobile Modem" and select "properties"
6) under the advanced tab enter the following under "Extra initialization commands":
AT+CGDCONT=1,"IP","sp.telus.com"
8) under the "network and sharing center" on the control panel choose "set up a new connection or network", then "set up a dial-up connection"
9) the phone number is *99# and the username and the password are left blank
This worked for the S3 but I haven't been able to get it to work on the S4 yet. Any help? I cant even get 1x
DFS
1) Go to the Programming tab.
2) Click on the Data sub tab.
2a) Click on Read button.
3) Under PAP:
UID: [email protected]
Pwd: samsung
4) Under HDR AN:
NAI: [email protected]
Pwd: (checked) enter your 32 digit HEX AAA password
5) Under HDR AN Long:
UID: [email protected]
Pwd: (checked) enter your 32 digit HEX AAA password
6) Put a check mark on "Authentication require password encryption"
7) Click on the Write button
8) Goto the Mobile IP sub tab.
8a) Click on Read button.
9) Right click on the first Profile radio button (that's Profile 0), and enable it.
10) Click on the Write button
11) On the Selected Profile settings section:
NAI: [email protected]
Home address: 0.0.0.0
Prim HA address: 68.28.15.12
Sec HA address: 68.28.31.12
AAA Shared Secret: enter your 32 digit HEX AAA password (put check mark on "Enter value in HEX")
HA Shared Secret: secret (remove check mark on "Enter value in HEX"
12) Click on Write current profile settings.
13) Reboot the phone. Then run the Update Profile and Update PRL on your Galaxy S3.
14) Done.
Bump anyone??
jkj said:
Bump anyone??
Click to expand...
Click to collapse
i dont understand?? are u flashing the gs4 to a diff phone service?
P.Mobile said:
i dont understand?? are u flashing the gs4 to a diff phone service?
Click to expand...
Click to collapse
I'm also curious too about op's question .... I want to buy a gs4 and keep it on sprint service but flash to my legacy plan. I've been tracking the Note 2 forum on xda and other external forums, can't find a legit instance of someone with working data on a flashed gs4.
In order for me to get 3g on my boost flashed s4 I had to input the settings for profile 1 that came from my donor. Its a different password than the 32 digit password u use on profile 0. My s4 would not ota with just profile 0 set. Stil doesnt but 3g works!
Sent from my SPH-L720 using xda app-developers app
strive53 said:
In order for me to get 3g on my boost flashed s4 I had to input the settings for profile 1 that came from my donor. Its a different password than the 32 digit password u use on profile 0. My s4 would not ota with just profile 0 set. Stil doesnt but 3g works!
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
This is exactly what I'm talking about. What program did you use to write the data profile? Care to share a mini tutorial?
jkj said:
This is exactly what I'm talking about. What program did you use to write the data profile? Care to share a mini tutorial?
Click to expand...
Click to collapse
http://forums.team-nocturnal.com/showthread.php/1064-got-my-Galaxy-S3-on-Boost-Mobile
Step 7b shows you how to pull it... I used efs to set up prof 1. Then step 28.
Sent from my SPH-L720 using xda app-developers app
strive53 said:
http://forums.team-nocturnal.com/showthread.php/1064-got-my-Galaxy-S3-on-Boost-Mobile
Step 7b shows you how to pull it... I used efs to set up prof 1. Then step 28.
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
so that activating thing doesnt come up every time you guys start the phone right? And you used efs or dfs? I am completely lost. Anyone thats got this to work on legacy please help.
So strange Ive got it to the point where I have the 3g icon. ##debug# sounds AN AAA status is pass but I cant go anywhere on the net. It says forbidden you dont have permission to access / on this server basically no matter where you go
jkj said:
so that activating thing doesnt come up every time you guys start the phone right? And you used efs or dfs? I am completely lost. Anyone thats got this to work on legacy please help.
So strange Ive got it to the point where I have the 3g icon. ##debug# sounds AN AAA status is pass but I cant go anywhere on the net. It says forbidden you dont have permission to access / on this server basically no matter where you go
Click to expand...
Click to collapse
Sorry was dfs..im flashed to boost so things may b different for u. I had to delete the app that pops up for the hands free activation so it would stop popping up. Did u pull aaa password for profile 1?
Sent from my SPH-L720 using xda app-developers app
I can confirm that you can get all this working on sprint legacy. I got Voice, Data, Text ... working but 3G data was slow. I did ##DEBUG# and put in lock code SPRINT (777468) ... goto EVDO Engineering Protocol ...State was INACTIVE ... AN-AAA was FAIL.
If your AN-AAA is fail then you copied over a DFS setting wrong. You'll need to re-write certain fields with DFS over and over again to get them to stick. I connected my Epic donor read all the tabs in DFS and took screen grabs of the Programming General, Data, NAMM (make sure you set NAM1 & NAM2), Mobile IP Profile 0, Mobile IP Profile 1. I connected the S4 to DFS and read all the tabs and compared them against the screen grabs. I did a write command to make sure every checkbox matched perfectly and the ones that couldn't be un-populated on the S4 I left alone. I then re-read the tabs with the S4 one last time to make sure the changes kept.
This solved my slow data connection with the S4. If I do ##DEBUG# then EVDO state is now Active and AN-AAA is pass.
Good luck.
strive53 said:
Sorry was dfs..im flashed to boost so things may b different for u. I had to delete the app that pops up for the hands free activation so it would stop popping up. Did u pull aaa password for profile 1?
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
dubroz said:
I can confirm that you can get all this working on sprint legacy. I got Voice, Data, Text ... working but 3G data was slow. I did ##DEBUG# and put in lock code SPRINT (777468) ... goto EVDO Engineering Protocol ...State was INACTIVE ... AN-AAA was FAIL.
If your AN-AAA is fail then you copied over a DFS setting wrong. You'll need to re-write certain fields with DFS over and over again to get them to stick. I connected my Epic donor read all the tabs in DFS and took screen grabs of the Programming General, Data, NAMM (make sure you set NAM1 & NAM2), Mobile IP Profile 0, Mobile IP Profile 1. I connected the S4 to DFS and read all the tabs and compared them against the screen grabs. I did a write command to make sure every checkbox matched perfectly and the ones that couldn't be un-populated on the S4 I left alone. I then re-read the tabs with the S4 one last time to make sure the changes kept.
This solved my slow data connection with the S4. If I do ##DEBUG# then EVDO state is now Active and AN-AAA is pass.
Good luck.
Click to expand...
Click to collapse
Its strange mine says pass no matter the active profile.. on profile 0 I get the 3g symbol but that forbidden error. On profile 1 I get no 3g symbol and error 67.
jkj said:
Its strange mine says pass no matter the active profile.. on profile 0 I get the 3g symbol but that forbidden error. On profile 1 I get no 3g symbol and error 67.
Click to expand...
Click to collapse
If you're getting error 67 the your profile 1 AAA key is not correct. It is not the same as profile 0.
I've written what I thought was the correct 12 digit key for profile 1 and it says pass under debug.... Could it still be wrong?
Error 67 is data profile error, regardless of what debug says there has to be something entered wrong in your profile 1 in dfs ... Redo the whole profile in dfs and recheck against screen grabs as I suggested.
Also, make sure you also updated the prl. I'm using PRL 56012
http://forum.xda-developers.com/showthread.php?t=1880781
Getting data to work on Sprint GS4 that has been flashed to boost?
I have flashed my S4 from Sprint to Boost. I own the donor; yadda yadda yadda....
I can make and receive phone calls and sms text messages, but I cannot get the data to enable?
Anyone have success (recently) with this?
jkj said:
This worked for the S3 but I haven't been able to get it to work on the S4 yet. Any help? I cant even get 1x
DFS
1) Go to the Programming tab.
2) Click on the Data sub tab.
2a) Click on Read button.
3) Under PAP:
UID: [email protected]
Pwd: samsung
4) Under HDR AN:
NAI: [email protected]
Pwd: (checked) enter your 32 digit HEX AAA password
5) Under HDR AN Long:
UID: [email protected]
Pwd: (checked) enter your 32 digit HEX AAA password
6) Put a check mark on "Authentication require password encryption"
7) Click on the Write button
8) Goto the Mobile IP sub tab.
8a) Click on Read button.
9) Right click on the first Profile radio button (that's Profile 0), and enable it.
10) Click on the Write button
11) On the Selected Profile settings section:
NAI: [email protected]
Home address: 0.0.0.0
Prim HA address: 68.28.15.12
Sec HA address: 68.28.31.12
AAA Shared Secret: enter your 32 digit HEX AAA password (put check mark on "Enter value in HEX")
HA Shared Secret: secret (remove check mark on "Enter value in HEX"
12) Click on Write current profile settings.
13) Reboot the phone. Then run the Update Profile and Update PRL on your Galaxy S3.
14) Done.
Click to expand...
Click to collapse
Same Ploblem
Hi
I have the same problem ,my phone (SPH-L720) flashed to other CDMA network outside USA , all the setting was right but unfortunately i couldn't get data working.
It's only connected for 2 minutes after phone boot up then drop automatically and couldn't get 3G again until reboot.
I noticed there was a gateway IP address in ##DATA# > View > Others > Browser > Gateway IP & Port & Secure Port
in ##DATA# > Edit > Others there is no option here to edit the gateway ip & ports
dubroz said:
I can confirm that you can get all this working on sprint legacy. I got Voice, Data, Text ... working but 3G data was slow. I did ##DEBUG# and put in lock code SPRINT (777468) ... goto EVDO Engineering Protocol ...State was INACTIVE ... AN-AAA was FAIL.
If your AN-AAA is fail then you copied over a DFS setting wrong. You'll need to re-write certain fields with DFS over and over again to get them to stick. I connected my Epic donor read all the tabs in DFS and took screen grabs of the Programming General, Data, NAMM (make sure you set NAM1 & NAM2), Mobile IP Profile 0, Mobile IP Profile 1. I connected the S4 to DFS and read all the tabs and compared them against the screen grabs. I did a write command to make sure every checkbox matched perfectly and the ones that couldn't be un-populated on the S4 I left alone. I then re-read the tabs with the S4 one last time to make sure the changes kept.
This solved my slow data connection with the S4. If I do ##DEBUG# then EVDO state is now Active and AN-AAA is pass.
Good luck.
Click to expand...
Click to collapse
What if your epic is long dead which is one of the reasons this route was chosen and nothing but the numbers for activation were used? Used to see error 67 a lot. Now just 131. No calls, texts, or data. By deactivating and reactiving my account one tech was able to get rid of the error 131 and a 3G icon popped up, but still had no data or anything....Then the call dropped and all her worked washed away with the other reps.....
I saw AAA fail in the debug menu so I guess I'll have to go to the other thread and look into them more.
yes hello i am trying to use qpst i go to configuration and i can see my phone i already did the virtual port and cdma workshop i am trying to
Section 4: QPST
When using QPST, don't let your phone go into sleep mode or it will lose connection.
1.) Open your Programs menu and go to QPST > QPST Configuration. If you do not see an active phone listed, select the "Ports" tab and click "Add New Port..." at the bottom right. Highlight the port you created for the DX, then click "OK." It should show the phone information. If it doesn't, check to make sure the DX is in PC mode.
2.) Close the window, and go back to Programs > QPST > Service Programming. Select the phone info, and click "OK." On the new window that pops up, click the "Read from Phone" button on the bottom left. A box will pop up asking for the SPC, but it already has 000000 in it, so just click "OK" and a blue progress bar will start creeping across the top left part of the screen. It might take a few minutes to finish.
3.) Click the "M.IP" tab. Select the entry for your phone, then click the "Edit" button. Make sure the NAI and Tethered NAI both read [email protected] or [email protected]. Your phone number should take the place of the xxxxxxxxxx. Home address, Primary HA address, and Secondary HA address should all be 0.0.0.0. If they aren't, change them. Click the "OK" button. While you're on the M.IP tab, make sure the Mobile IP behavior drop down is set to "Mob + Simp f/back" and Active User is set to 0.
4.) Select the "PPP Config" tab and click the "Um" button. Tethered NAI and User ID should be the same as they were in the M.IP tab. The Req PW box should be checked. In the password field, type in either "cricket" or "metropcs" depending on your carrier. Click the "AN" button, and make sure the USR ID is the [email protected] or [email protected]. The Req PW box should be checked, and the password is the same as it was for the Um tab. Tethered NAI should be blank and grayed out.*
5.) Click the "Write to Phone" button on the bottom of the screen. It may take a few minutes, and the phone may reboot. When it comes back up, you should have web access.
but when i click on service programming i get online conection failedhone model pt-surf6300-zrf6300-nand not supported. so what do i do next
Hello all! I recently won a Sprint Moto X on eBay for the shockingly low price of $130, and I decided to attempt to flash it to Page Plus. So, in order, that others may benefit from this awesomeness, I decided to post a basic guide. One thing to note is that, if you have flashed Sprint phones to Page Plus before, the process is very similar.
DISCLAIMER: This guide comes with no guarantees of any kind. If you lose personal data or service, brick your phone, or lose your arm to gangrene, I am not responsible.
Stuff You Need
A PC running Windows
Motorola Drivers (download here)
SPCUtility APK (download here)
DFS (download here)
QPST (download here)
Page Plus PRL (attached)
10.key file (attached)
Stock, rooted Moto X 4.4.2 firmware (you can try an older version, but I've only tested on this)
How to Do It
First, if you don't have one, get a Page Plus phone number and account. You'll need it for manually programming.
If you have trouble getting Page Plus to accept your ESN (which is the MEID you'll find in Settings > About Phone > Status), try live chat until someone is okay with activating a 4G phone. They will probably warn you that they offer no support for programming 4G phones.
Make sure to Live Chat with Page Plus and ask for your MDN, MIN, and SID. Most likely, your MDN and MIN will be your phone number.
Once everything on Page Plus' end is set up, dial ##DIAG# on your phone. In the screen that appears, click the overflow button and choose Edit. Then set Diag Port to Enable.
Now install the Motorola drivers so you can connect your phone to your PC. This is sometimes a tricky process, and I don't know why. Google is your friend if you have trouble. When successful, you will see this in Device Manager.
Before attempting to program, you need your MSL. Install the SPCUtility APK and use it to get your MSL.
If you haven't already, install DFS. Open the program and click the Ports button in the upper-left corner. Then double-click the Motorola QC Diag Port to select it. (If you don't see this port, the drivers are not properly set up.) Close the Ports window.
Enter your MSL in the SPC box under the Ports button. Then click the SPC send arrow. Your log window should show DEVICE UNLOCKED. (If the log window is not visible, click the Log button in the upper-right.)
(Optional) In the General tab, click Read in the SPC box. Then replace the SPC string with 000000 and click Write. This sets your MSL to all-zeroes, useful for future programming.
In the General tab, click Read in the Config box. It may already read NV_ONLY. If it does not, set it and click Write.
Go under the NAM tab and click Read at the bottom. The fields will populate with your phone's current programming. Now replace the numbers in both MIN A and MIN D fields with your MIN. Fill the MDN and PCS fields with your MDN. Finally, in the Home box, fill in your SID and click Write.
In the PRL box, click Load and select the Page Plus PRL you downloaded. Click Write.
At this point, you may click Reset and your phone should have talk/text. Try taking and sending one of each to verify that everything has gone right so far.
Now go back to DFS and send your SPC again to get back to work. In the Data tab, click Read, and then fill out all of the UID fields and the HDR AN NAI field with [email protected] (the X's being your phone number). In the PPP SIP NAI, use [email protected]. Put "vzw" (sans quotes) in all of the password fields, and make sure the authentication box is checked. Click Write.
Go to the Mobile IP tab and click Read. At this point, I admit that I do not know 100% what I am doing, but that these settings worked for me. Basically, make your settings look like these ones, but input your number where I scribbled out my own. Also, for everything in the Selected Profile Settings box, put it in both the first and second profile selections. After filling each of those out, click Write current profile settings. Then click Write in the left box.
At this point, reset your phone. You might have working 1X after a minute. Irrelevant, because we're about to go for 3G. Close DFS.
Open QPST Configuration (install it if you haven't). Click Add New Port... and select the only available port. Click Okay, then go to Start Client > EFS Explorer. Select your phone and enter your MSL. It will take a minute to read the phone's EFS data.
Once the EFS data is loaded, right click the root directory and click New > Directory. Name the new folder DMU.
Inside the DMU folder, click File > Open and select the 10.key file you downloaded. Verify the target path is /DMU/10.key.
When the file is copied successfully, click Phone > Reset Phone. When the phone reboots, wait a minute or two. You should have 3G!
3G speed test results here
MMS Fix
Download and install 8sms from the Play Store or their website.
If you're using KitKat, be sure to set the new app as your default SMS app.
In the app, go to Settings > MMS Settings.
Now set the following:
MMS Network: Sprint
MMSC: http://mms.vtext.com/servlets/mms?X-VZW-MDN=XXXXXXXXXX (the X's being your phone number)
MMS Proxy: leave blank
MMS Port: 8080 (if that doesn't work, try 80)
MMS over WiFi: Off
Volia! You should have working MMS.
Now, I freely admit that there are numerous places to go wrong here, but this is what worked perfectly for me. If you have trouble, tell me and I'll try to help. Also, check out this thread for general flashing reference. Viper is an expert at these kinds of projects.
Happy flashing!
Can I flash Sprint Moto X to Verizon ? and else does you did it already with success
MrSaba said:
Can I flash Sprint Moto X to Verizon ? and else does you did it already with success
Click to expand...
Click to collapse
Flashing between major, independent carriers is illegal. Legally we can only flash between MNVOs.
but what mean MNVO ? I am not USA citizen I live in Republic Of Georgia
MrSaba said:
but what mean MNVO ? I am not USA citizen I live in Republic Of Georgia
Click to expand...
Click to collapse
Ah, in that case I don't know Georgian laws. Even so, I do not know how to flash to Verizon, or even if it is entirely possible.
pageplus is cdma network only? in georgia its not illegal to flash on other network. I need to make sim unlock for gsm metworks
Sent from my DROID RAZR HD using XDA Premium 4 mobile app
MrSaba said:
pageplus is cdma network only? in georgia its not illegal to flash on other network. I need to make sim unlock for gsm metworks
Sent from my DROID RAZR HD using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Yes, Page Plus is CDMA only.
Updated with MMS fix.
Nice guidance.. Carry on..:good::good:
When entering ##DIAG# it asks for a passcode tried 000000 it didn't work
Any ideas??
Thanks very much for the post
ac2014 said:
When entering ##DIAG# it asks for a passcode tried 000000 it didn't work
Any ideas??
Thanks very much for the post
Click to expand...
Click to collapse
It wants your MSL/SPC code. Look for the app called SPCUtility.apk in the OP.
I downloaded it from an XDA page by the guy who developed it but I no longer have the URL and don't recall his handle.
It will tell you your subsidy unlock code, at least it did for me on my Moto X and for several other folks with other Android phones.
How do i get the drivers installed properly?
ac2014 said:
How do i get the drivers installed properly?
Click to expand...
Click to collapse
here's how to install the driver
search for this on google it should be the 1st youtube video
"How to Install Motorola QC Diag Driver"
so i got everything working thanks very much
just few things
1) every time restarting the hone it goes to activation any way to remove it ?
2) im getting notification "Mobile IP Registration response error MIP Error 131:mobile node failed authentication" which makes me nurses cause it pops up every few seconds :crying:
any help would be appreciated
thanks in advanced
ac2014 said:
here's how to install the driver
search for this on google it should be the 1st youtube video
"How to Install Motorola QC Diag Driver"
Click to expand...
Click to collapse
Which version of QC Diag Driver you have used ?
DANIEL AMBRUSO said:
Which version of QC Diag Driver you have used ?
Click to expand...
Click to collapse
The latest available. Dono exactly which 1
ac2014 said:
The latest available. Dono exactly which 1
Click to expand...
Click to collapse
Exactly i want to know about your available version..
DANIEL AMBRUSO said:
Exactly i want to know about your available version..
Click to expand...
Click to collapse
Motorola Mobile Drivers 6.3.0
I successfully got talk and text with this but no data connection. Does anyone have data working?
lswiggins said:
I successfully got talk and text with this but no data connection. Does anyone have data working?
Click to expand...
Click to collapse
It did took 3 minutes but showed up
It might be a bit tricky, u have to input in 2 spots. As you can see it pic provided by @Nicene Nerd
Nicene Nerd said:
Basically, make your settings look like these ones, but input your number where I scribbled out my own. Also, for everything in the Selected Profile Settings box, put it in both the first and second profile selections.
Click to expand...
Click to collapse
Did u input the 2nd profile?