when i run HSPL and click next and then its says waiting for USB connection and i connect my hd2 to it nothing happens and then it says error communication timeout error code:0x10001 always reference. ive been stuck on this for a day so if anyone knows whats the problem can you please help me
go into bootloader yourself manually, connect usb, wait ten seconds, right click hspl and "run as administrator"
if still fails keep trying different usb ports.
Use the rear USB ports on the back of your computer (rear mobo panel). The Onboard USB connections did not work for me either.
Related
My cingular 8125 USB port was working just fine unti I rebooted the 8125while it was runing wizardbackup uitility b/c I did not have the min sd card to back it up( my....). So, now the usb port is no longer working. Activesyn can't connect but the device is charging when I have the device connected to a labtop via usb cable. I hav tried:
- Hard reset & soft reset on the device
- Reinstall Activesysn
- Activsycn is set as usb in the device
thanks much.
w
Confirm your hardreset(many doesn't realised what they did is just softreset)
Try different cable different PC.
Use Wm5torage to test if you want.
Try activesync via IR/bluetooth.
I have tried all of these and none of these response (bluetooth, iR, different pc, etc..) . Can I reflash my ROM from mini SD.
thanks,
hn
weester said:
I have tried all of these and none of these response (bluetooth, iR, different pc, etc..) . Can I reflash my ROM from mini SD.
thanks,
hn
Click to expand...
Click to collapse
Only if its CID Unlocked
How can I unlock CID if I can't get to USB, ir/bluetooth connection via activesyn. Can I do it via mini SD? if so,please show me how.
thanks,
hn
Can you get into bootloader mode (The 3 colorbars)??? If yes, plug in the usb and see if it reads in the lower corner (it will say usb). If yes, you should be able to re-flash your phone, and from what you wrote, it sounds as if the usb will read...however, if your usb port is damaged, you may have a bigger issue to deal with.
For more detailed info, click the linky in my siggy. It is the most complete thread I know of about saving a wizard from death.
Most wizards can be saved...mine wasn't but mine was severely damaged...that being said, the thread linked below gives great info on various methods.
Also, if it is an active-sync issue, it can usually be corrected.
Read the thread, see if any of it helps, then report back if you need more help.
I can get into bootloader mode (The 3 colorbars) I then plug the usb to my pc and usb see it for 2 seconds and it disappears saying "USB is not recognized". When I try to flash the "RUU_wizard_225111_22511102_02252_CWS_wwe" downloaded from htcwizard website and i get " ERROR [260]: UPDATE ERROR".
Hi guys ,my problem is that when I connect my phone via USB cable at first there is no problem, data transfer , windows mobile device center, everything is OK. But when I want to flash the phone pressing vol-down + switch on/off keys the phone is not connected to the PC. And I can't flash it. Also the phone wouldn't like charge trough the charger ,only with the data cable. Is it possible to have any liaison between the problem with charging with charger and no-connection when try to flash.
Also my phone was to the service for touch-screen change ,is it possible the technician make any mistake ? Cause I think that if he make a mistake with the connector nothing gonna work ,but it works at different situations.
Regards!
check to be sure USB SYNC driver installed correctly and also try a different usb cable.
I'll try but there is no logic ,the cable works when charge the phone, works when is connected to device manager but doesn't works when flashing ?
exactly. the device requires different drivers.
1. there is internet sharing and disk mode (which works with all computers, because those drivers are in the operating system)
2. then there is one driver for syncing
3. and another one for flashing
it is not the same kind of data transfer, which is why you need a different driver. but the thread "[tut] updating htc sync drivers" should cover all your windows vista/7 driver needs and a tutorial on how to install them, which in case of a x64 system can be fairly complicated.
if you already have hspl installed (which you can determine by entering bootloader mode and looking whether it says 1.56Olinex), you can also flash using the sd car method. put a rom of your choice on the sd card, name in BLACIMG.nbh and enter bootloader mode, you will be presented with options to flash the rom.
Ok, but in instructions at the thread you give me is written that I have to start making the steps after I see "USB" on the flashing screen. But I don't see it, it's only "Serial". And now what ? I know that if on the screen i written "USB" the phone and the computer are connected and there is no problem to flash ,but now what ?
well, before you start, put your device into bootloader mode. it will show "serial", then connect it to the pc. test your connection using mtty 1.42 (you'll find several download options here in the forum).
the connection settings for mtty are USB 115200-8-1-No-NONE-None
if it works, connect and press enter, the command shell should show USB> then.
if usb is not present in the connection settings, your connection is not established yet. proceed with the tutorial then. during the entire procedure, the device should remain connected to the pc in bootloader mode, so you install the driver for the right device state.
Hello,
I've problem something like this. Few months ago when i was conecting my phone to computer was everything OK, activesync, disk drive, but now nothing, just charging the phone. I've tryed everything in USB to pc zone, but nothing. When i'm going to bootloader it's writen serial. What can be here?
since you already tried all the different connection methods and even bootloader mode does not connect, there are hardly any options left, where the trouble could be:
- the usb port on the blackstone
- the usb port on the pc
- the cable
you can try another port on the pc (or even better, another pc altogether) and/or another cable, like from a digital camera, an external hdd... (many devices have mini usb cables, you should be able to use either one of those)
My main issue is drivers. I ended up formating my computer with a fresh install of Win7 64-bit few weeks ago, but did this with android on my phone. So now I have a dilemma.
I cannot get drivers anywhere [online] that will let me go into any USB mode for either:
MAGLDR
or
Tr-Color Screen
So either with magldr it just sits there forever saying USB Wait...[never says usb]
And with tri-color screen it never says USB, if I try different USB ports it says Serial and never changes to anything else.
I think my problem is I need WM back, and sync it with WMDC. The problem to that? I cant even flash WM...
Anyone know of any other way to get the drivers for Win7 64? So I can use USB Flasher or tr-color screen.
Hope someone knows a solution...I have been looking for weeks to a resolution to this problem :-/
Thanks in advanced
Try reinstalling Windows Mobile Device Center.
I tried that, I installed it and it installed a Microsoft Mobile device driver, but it still does not say USB on the flasher mode or on the tri-color screen...
Can anyone find out the name of the driver/device when they plug their phone in and it enables USB (under usb flasher or tri-color screen)? Maybe from there I can search better names for the right driver...
Any ideas? Just trying to see if anyone knows any solution to this...
Thanks
UPDATE:
Ok, so I had a minor cut in my cable, with only the shielding wire coming out a little bit. I luckly had another micro usb in house that I could try. Seems if there is the slightest problem with your cable, get it replaced. MY USB WORKS FINE NOW . Try new cables if you are having serious driver issues (tried it on 2 computers, thats when I said it has to be the cable.). Could be the simple thing.
As the title says, my phone wont recognize when I plug in the USB on to flash the DAF. I have done it several times before but now it doesn't work for some reason? So to clarify it's stuck on "wait USB..." and won't get to the point where it says "wait USB... USB".
Using MAGLDR v1.13
Does anyone have any ideas?
Restart your PC should solve your issue....at least it does several times for me.
icke said:
Restart your PC should solve your issue....at least it does several times for me.
Click to expand...
Click to collapse
yes
If not, you would need to uninstall the drivers needed to perform the usb connection. Then connect your phone again, and it should automatically install.
Reinstall driver and try another USB port, too
I don't really depend on "wait USB ... USB" as it is not very accurate .
Sometimes, I don't see " .... USB" until I double click DWF and hit next twice.
I do get the windows sound when you connect something with usb so maybe the "wait USB isn't accurate" just wasnt sure. Will try it, thanks
my comp never "recognizes" wait usb ... usb
i just start the DAF and all goes well. go ahead and give it a go ... whats the worst that can happen? worst case the DAF wont start right? :-D
Thanks for the help guys, got it to work
What always worked for me:
Open Windows Mobile Device Center.
Turn ON USB Connections.
Connect the USB cable to the phone.
Turn OFF USB Connections.
Flash
Loaded Android on my HTC HD2. Had issues with android, so I went back to Windows. Used the following to load Android
SPL-2.08.HSPL
Radio that support 576 MB RAM
DFT MAGLDR Bootloader v1.13
ClockworkMod Recovery v1.3
Now want to load android ROM again, but USB port will not work when I power on phone holding down volume button. Goes into multi colored screen but I never get USB in the white field. USB works fine when phone is being charged. When plugged into USB port on computer when in Windows mobile, PC does not recognize phone. Searched forums and it seems like a lot of people are having this issue, but no one seems to have the solution to the problem. Was hoping someone could help with this. Thanks!
Are you sure you have Active Sync or Windows Mobile Device Center installed on your computer? You have to have the correct version of this to have the correct drivers on your computer.
T-Macgnolia said:
Are you sure you have Active Sync or Windows Mobile Device Center installed on your computer? You have to have the correct version of this to have the correct drivers on your computer.
Click to expand...
Click to collapse
Yes, I have WMDC installed. My bigger concern is why the connection will not change from serial to USB when I boot into the multi colored screen by holding down the volume button while powering on the phone. If I have the USB plugged in when I'm booting to the multi colored screen, it just displays a white screen where it should say serial or USB.
jnobles1973 said:
Yes, I have WMDC installed. My bigger concern is why the connection will not change from serial to USB when I boot into the multi colored screen by holding down the volume button while powering on the phone. If I have the USB plugged in when I'm booting to the multi colored screen, it just displays a white screen where it should say serial or USB.
Click to expand...
Click to collapse
If I am understanding you correct if you have the USB plugged in when you boot to bootloader(multicolor screen) it only displays a white screen. Does it x the Sam thing if you boot to bootloader and then connect your USB cable? Also I reread your first post and I see you also say your computer does not recognize the device when you are booted into a Windows Mobile ROM and you plug the device in via USB. Now this is really not good as it might mean your micro USB port on the device nolonger is functioning for data transfer. I suggest you connect your device via USB and then go to Control Panel and open Device Manager and seecwhat your device is listed as there, post it back here in this thread too pleased. I have a feeling though that you are just having a driver issue.
T-Macgnolia said:
If I am understanding you correct if you have the USB plugged in when you boot to bootloader(multicolor screen) it only displays a white screen. Does it x the Sam thing if you boot to bootloader and then connect your USB cable? Also I reread your first post and I see you also say your computer does not recognize the device when you are booted into a Windows Mobile ROM and you plug the device in via USB. Now this is really not good as it might mean your micro USB port on the device nolonger is functioning for data transfer. I suggest you connect your device via USB and then go to Control Panel and open Device Manager and seecwhat your device is listed as there, post it back here in this thread too pleased. I have a feeling though that you are just having a driver issue.
Click to expand...
Click to collapse
If I boot to bootloader and and then connect USB cable, it stays on serial and never changes to USB. When I plug it into my computer, the light comes on to show it is charging, but the computer never sees it. Even if I scan for HW changes, it never sees the device. Windows doesn't make the sound it normally does when you plug a device in via USB.
jnobles1973 said:
If I boot to bootloader and and then connect USB cable, it stays on serial and never changes to USB. When I plug it into my computer, the light comes on to show it is charging, but the computer never sees it. Even if I scan for HW changes, it never sees the device. Windows doesn't make the sound it normally does when you plug a device in via USB.
Click to expand...
Click to collapse
I definitely think you are having a driver issue, try this if you do not have a Windows Mobile ROM on your device and see if you can do any kind of data transfer via USB. Try doing some file transfer on your SD card, if you can do this then yes you most definitely have a driver issue. I would then re install WMDC and then boot to bootloader and see if you get the USB in the in the white bar of bootloader that shows you have the HTC Sync connection.
Unable to do any kind of transfer via USB because PC does not see phone as being plugged in when I connect it to the USB. Storage on the phone does not show up under My Computer as additional storage when connected. Attempted to reinstall WMDC and it gives an error saying that it can not install the device drivers. You mentioned Windows Rom, phone is running Windows Mobile, if that is what you meant. Thanks!
jnobles1973 said:
Unable to do any kind of transfer via USB because PC does not see phone as being plugged in when I connect it to the USB. Storage on the phone does not show up under My Computer as additional storage when connected. Attempted to reinstall WMDC and it gives an error saying that it can not install the device drivers. You mentioned Windows Rom, phone is running Windows Mobile, if that is what you meant. Thanks!
Click to expand...
Click to collapse
Try another USB cord, a bad cord could charge the phone but not connect S/W recognition
orangekid said:
Try another USB cord, a bad cord could charge the phone but not connect S/W recognition
Click to expand...
Click to collapse
Have tried 3 different cords, all with the same results.
jnobles1973 said:
Have tried 3 different cords, all with the same results.
Click to expand...
Click to collapse
Man in that case I hate to say it but it sounds like the two data pins in the micro USB have stopped working.
Have you tried another computer?