Guys, I changed the housing of my old P4350.
Everything works perfectly. Screen, buttons, keyboard, etc.
Tha only issue is that the screen is not rotating when I slide the keyboard.
What did I miss?
anyone please?
no one? please help
Probably is only a frosen image If you leave the keyboard out for a while at one point the image should rotate if this is not the case you should try to soft-reset the phone or change to a more stable rom that may help and u will see a difference.
Worse case you may need to dismantle it again, there is a sensor between the screen an the keyboard that rotates the screen as it slides, I know is a pain to take it apart again. I also did replace my HTC 4350 with a black housing but did not encounter that problem.
good luck.
Related
I did some searching for someone reporting a similar issue but i didnt find anything.
my question is with an issue im having with my cing 8125. when i slide the keyboard out, or even start to slide it out, the screen goes really crazy, and isnt readable. i tried to take some screen shots of it, but the issue doesnt show up on screen shots since the screen capture intercepts the signal before it gets to the display. has any one else had an issue like this? is it possible to open up my wizard and fix it, or am i stuck using the onscreen keyboard until i get a new phone?
Have you tried to reset your device? Maybe its really just a problem with your firmware. If it were a hardware problem, it would not only appear if you slide the keyboard out, i think.
Duke
hey i was just wondering if someone could help me out here, ive searched around with no luck. I replaced my wing's housing because my old one was all scratched everything works fine but i have one problem when i slide out the keyboard the screen doesnt go to landscape mode and i have no idea whats broke checked all the cables and stuff and its all pluged in, the keyboard works just wont rotate the screen thanks
You can try a hard reset, which should cure any software problems.... but if you were messing with the phone and taking it apart in order to replace the housing ... it sounds like a hardware issue.
its defenitely hardware related just not sure what it could be not sure where the thing that operates the screen and turns it when the slide is open would even be
I had the same problem. Their is a little round magnet in the front housing that you forgot to swap from the old case. Its hard to notice but its in one of the corners in the screen side housing. its under the OK button, under the circuit board. on the actual sliding plastic housing. you'll see a small round recces thats where the magnet goes.
the wing has a Prossesser Of 200Mhz, so what that means is its pretty slow.. just uninstall unused programs and End programs that your not using. Its also possible that your firmware might not Support Sliding.
Hey guys... I'm having a lot of troubles with the lcd screen on my 8525 and this start about a month ago.. I've had this phone for almost one year... bought it as a refurb.
1. when i'm using the phone portrait mode the screen alignment would be perfect... however when i slide the keyboard open the screen goes to landscape and my alignment would be completely off. Heres the interesting part... say if it is still in landscape and i align it then.. it would work perfectly in landscape but then when i close the keyboard and go back to portrait the alignment would be extremely off again.
2. now when i'm in portrait mode and i go to start -> settings -> system -> screen and switch the screen to landscape (w.o sliding the keyboard open) the screen would be perfectly aligned... but when i slide the keyboard open... the alignment would be completely off again... now if i align it while it is in landscape (keyboard open) and go to start..settings..system..screen and change it to portrait the alignment would be perfect... but when i close the keyboard.... it would be off again...
is there anyway i can fix this? I've done a hard reset and flashed the firmware all over again... btw i'm using WM6 from the htc website. if anyone can help...lemme know what i have to do....
thankz
p.s my phones starts with s/n ht649.
Can't say I've seen that reported before. Sounds software based. You could try backing up and hard resetting.
Mike
I already tried that.. it didn't work.
Sorry, my bad - you clearly said you had done that already.
I can't fathom what hardware problem there could be. The magnet orientation switch is clearly fine it seems the X Y co-ords are not swapping over - but that seems a software matter, yet your hard reset suggests hardware - Im stumped.
Mike
If the whole screen is moving, including the start menu etc,
I have seen this before, when building my phone, if the lcd ribbon cable is not alligned perfectly this can occur... but resetting the device did not resolve the issue in this instance.
Cheers
Steve
So I guess I'll have to take it to a cellphone repair shop and have it looked at. I just hope it won't cost too much... the phone was a refurb and i got it for $100. Do you guys have any other suggestions?
Whenever i slide out the keyboard the screen either becomes unresponsive or blacks out. I tried flashing two diff roms from itje and smaberg but they both have the same problem. The screen also becomes very inaccurate and unresponsive. Anyone have such problems?
Nope, here is fine.
The question - does the situation STAY this way or just happens for a few seconds?
Now the screen doesnt even work, when i slide out the keyboard the whole screen blanks out.
custom rom?
Exactly.
The questions:
1. Do you use custom ROM's?
2. Or what did you install
Also
3. Did your phone falled down? I mean - it may be a mechanical problem with connection with 2 parts of the device, no?
I've tried 2 custom now im back on the official one, looks like its going to the service centre. I think its a mechanical problem. When the keyboard is slid out, the screen appears to power down with some colours appearing, when it is in fact still on.
I think the magnet of your x1 has some problem,as we all know,system determine the keyboard sliding by magnetic induction,
and here is a way to test it,you can put you x1 on somethings which has a big magnet, if x1's screen rotate, I think magnet of your x1 has some problem or lose,
I sent it to service center. Hope it gets fixed well.
hi,
Recently i changed housing case of my htc p4350 herald.. all works great.. all keys works nicely.. only problem i have is when i pull out my qwerty keyboard, usually it should align screen so i can typ.. but its not aligning the screen it stays in portrait itself.. but keyboard is working fine.. very confused.. i checked all cables etc.. all r in their position can anyone pls suggest me something?