Related
ok i think iv killed my m600
i flashed it with the older imate rom the 1.0.9 version
it installed 100% and rebooted and from ther it was stuck on the imate screen for like 10 minutes and i see the following text in red on the top left corner
---------------------
IPL 2.10.0001
SPL 2.15.0001
GSM 01.14.20
OS 1.0.9.25
-------------------------
i tried removing the battery and restarting the fone. still the same thing. can someone please please please help me with this?
what do i do?
im sure orange wont help me out since i flashed it with a non-orange rom.
never mind fixed itby goin into the bootloader
funky_Saggi said:
never mind fixed itby goin into the bootloader
Click to expand...
Click to collapse
hi there i seem to have the same problem as you with the boot screen. top left corner say's
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 1.0.13.21
can you please tell me how you fixed yours please it would be a great help
What you could do is flash it with an newer rom
Hold camera button AND reset (be asure that it hold it while resetting)
Then... you are in you bootloader... connect the PDA with your PC..it will recognized it!
Then run the romupdate ;-)
Hi thanks for trying to help me i got my phone in to the 3 colour screen but my computer does not pic it up at all. is there another way to save my M600
crossy4life said:
Hi thanks for trying to help me i got my phone in to the 3 colour screen but my computer does not pic it up at all. is there another way to save my M600
Click to expand...
Click to collapse
Aren't you getting "USB" written in the bottom left corner of the 3 colour screen when you connect it to USB?
Yes i get the USB come up at the bottom of the screen my computer does not do anything. can you tell me which ROM i will need as the ones i have to run the ROM update but it comes back saying connect to ActiveSync which i can not do is there a way round this?
Final got my SPV M600 Working with the ROM from the download area thanks for the help anyway
cheers
just change the usb port to another one and start rom it should pick it up
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
Hello guys, I hope you can help me.... In the middle of a ROM update my (!#@#[email protected]#) PC rebooted.... (while in the white screen on my Qtek 9100) Now the only thing it will come up with is the colored screen saying: IPL 2.21.0001,SPL 2.21.0lip and the USB is on. Active sync isn't able to connect to my device so now what?? Is it bricked?
Hope sombody can help me.... the colored screen means something's still working isn't it?
thanx in advange,
NEVSKI
what update were you trying to install? WM5? WM6? Official or cooked?
What windows xp/Vista are you using?
How far had the update gone
Have you tried running the update again,just tick the i have an active sync connection ,even though you dont and see if it will update? While in the bootloader screen the coloured screen. Hopefully it will do it for you
NEVSKI said:
Hello guys, I hope you can help me.... In the middle of a ROM update my (!#@#[email protected]#) PC rebooted.... (while in the white screen on my Qtek 9100) Now the only thing it will come up with is the colored screen saying: IPL 2.21.0001,SPL 2.21.0lip and the USB is on. Active sync isn't able to connect to my device so now what?? Is it bricked?
Hope sombody can help me.... the colored screen means something's still working isn't it?
thanx in advange,
NEVSKI
Click to expand...
Click to collapse
Its a bad flash as your PC crashed,the update did not finish and you don't have a working OS on your device.As long as you are getting into Bootloaders (multicolored screen) the phone is working,it's definitely not 'Bricked'.,but bad flash might have corrupted the bootloaders (IPL/SPL) on your phone.
Therefore to recover it back to it's default status,download the official carrier's Rom from it's website and flash it in bootloader mode(multicolored).You don't need to establish Activesync connection as Activesync will not work in bootloaders.Just get the phone in bootloaders ,connect your phone with the pc via usb cable,check usb appear at the bottom of the bootloader screen in the phone and run the Ruu in the rom,let it finish and reboot,hope it'll recover to it's default working status and than do what ever you want to do.
Good luck
still a No Go......
well, I still got the 3 (with the white 4) colored screen saying: RUU, IPL 2.21.0001, SPL 2.21.0lip and USB in the white...... I tried a RUU but that didn't work. I had this phone flashed with WM 6 DUTCH and it worked like a baby untill I tried to SIM unlock it... doing that the PC crashed.... Explain please how to get the right ROM and maybe some more info on how to do it after I got the ROM downloaded.... I want my Qtek so bad....
NEVSKI
Yeeeeeeehaaaaaaa!!!!!!! I got it 'up 'n running'....
NEVSKI
igot the same problem
it comes up with the 3 colourd screen usb at the bottem in the white when i put usb cable in but wont connect to active sync i dont no whare to get the 02 rom from can any on help please
I couldnt flash Hardspl any more.
I couldnt install either cooked rooms or original one.
All I see is the tri color screen with the following informaiton:
PLA100
SPL-1.25.0000
CPLD-2
Can you please help?
osama966 said:
I couldnt flash Hardspl any more.
I couldnt install either cooked rooms or original one.
All I see is the tri color screen with the following informaiton:
PLA100
SPL-1.25.0000
CPLD-2
Can you please help?
Click to expand...
Click to collapse
please search before posting a new thread!
http://forum.xda-developers.com/showthread.php?t=425922
nicandris said:
please search before posting a new thread!
http://forum.xda-developers.com/showthread.php?t=425922
Click to expand...
Click to collapse
I saw this yesterday, and I give it a try, the only issue I have is I have windows vista, so there is no active sync.
I tried to kill the process using ctrl Alt Del in order to see the USB port but I couldnt managed to do that.
Under windows Vista its called 'Windows Mobile Device Center' (wmdc.exe).
I tried everything
Dear All : I tried almost every thing mentioned in this subject over 4 or 5 threads ,I'm still not able to connect through USB ,I tried MTTY and also I can't see the USB in the available ports ,I tried with winXP and killed the activesync processes and tried with Win Vista and also killed the WMDC process BUT no way I failed.
At the boot screen I have the following
Pola100 MFG
SPL-2.20.oliNex
CPLD-2
Anyone have a solution please I use my Polaris in managing my business and now I;m in deep ****
hamed_marie said:
Dear All : I tried almost every thing mentioned in this subject over 4 or 5 threads ,I'm still not able to connect through USB ,I tried MTTY and also I can't see the USB in the available ports ,I tried with winXP and killed the activesync processes and tried with Win Vista and also killed the WMDC process BUT no way I failed.
At the boot screen I have the following
Pola100 MFG
SPL-2.20.oliNex
CPLD-2
Anyone have a solution please I use my Polaris in managing my business and now I;m in deep ****
Click to expand...
Click to collapse
i can see that hardspl is installed. did you tried flashing from sdcard?
i have had problems with stuck in bootloader (3 color) mode and also the prob with mtty in win vista...i try it on winxp and wow...it goes...
You use it to manage your business? Next time, dont mess with the ROM on your phone then
You seem to have SPL on the device. Try a different USB cable perhaps for connectivity.
nicandris said:
please search before posting a new thread!
http://forum.xda-developers.com/showthread.php?t=425922
Click to expand...
Click to collapse
i have the same problem and i tried this and tried almost all other bootlaod related threads and nothing worked, i have win xp and i can use the software advised but after everything works and the devise restart nothing happen and here we go to the same bootload three color screen.
what is shows is the following:
POLA100
SPL-1.28.0000
CPLD-2
the funny and wierd thing is that this happened without any notice and not during flashing or upgrading, i left the phone on the table and came back to see it stuck in the bootload screen
please help guys ..i spent till now 6 hrs with no benefit .... im a normal user
nicandris said:
i can see that hardspl is installed. did you tried flashing from sdcard?
Click to expand...
Click to collapse
I tried flashing from SD card and I had only the tri color screen with the data mentioned before and nothing happens,I tried use MTTY and I could never have the USB port listed in the drop list.
Thanks for your concern and in advance
wesram said:
i have the same problem and i tried this and tried almost all other bootlaod related threads and nothing worked, i have win xp and i can use the software advised but after everything works and the devise restart nothing happen and here we go to the same bootload three color screen.
what is shows is the following:
POLA100
SPL-1.28.0000
CPLD-2
the funny and wierd thing is that this happened without any notice and not during flashing or upgrading, i left the phone on the table and came back to see it stuck in the bootload screen
please help guys ..i spent till now 6 hrs with no benefit .... im a normal user
Click to expand...
Click to collapse
guys please helpppppp
up
hey ım usıng touch cruıse
pola100
spl 3.13.00
cpld-2
my cruıse not oen ower.always bootloader trı color .usb ok but ofıcıal rom ınstallıng problem yüzde1 later shuttıng.what must ı do?
well my phone after i flashed and installed wm 6.5 it was working totally fine, but this morning i turned it off and then on and it totally freezes at the startup screen and never loads windows. what i can do?
i'll appreciate any comments
i have then same problem switches on displays, disigned for windows mobile 6.5.5 then freezes
Yeah many ppl has this issue... be sure to flash first the att stripped att stock rom then hard reset then boots then reflash the custom rom then hardreset then try again to use th rom maybe it works ok now
I have the same problem
but I have the same problem. I bought a second hand phone and also freezes on the welcome screen and to make the rom? I need it so I can re-flash the windows
I have problem with my tytn, i was traying 7-8 rom of win mobile 6.1 or 6.5 but no help, my htrc cant find nework or when he find network he was online 1 hour and after hat he he offline in phpne mode, what is a problem, radio, rom or... ????
miljan017 said:
I have problem with my tytn, i was traying 7-8 rom of win mobile 6.1 or 6.5 but no help, my htrc cant find nework or when he find network he was online 1 hour and after hat he he offline in phpne mode, what is a problem, radio, rom or... ????
Click to expand...
Click to collapse
try to upgrade radio version on your device !! you can find Radio Rom Wizard in http://forum.xda-developers.com/showthread.php?t=300713 or at http://forum.xda-developers.com/showthread.php?t=268031
i cant start update proces always error 260 or 262
Jasjam Freez on i-mate logo
Dear Friends
my jasjam stop on first screen(i-mate Logo) . I did soft and hard reset again and again but nothing!i remove battery and sim card along the night but nothing again.pls help me what's problem
Thnkas and goodluck
Batman1351 said:
Dear Friends
my jasjam stop on first screen(i-mate Logo) . I did soft and hard reset again and again but nothing!i remove battery and sim card along the night but nothing again.pls help me what's problem
Thnkas and goodluck
Click to expand...
Click to collapse
probably you need reflash again your device with Original Shipped ROM
JasJam Freez on Logo
Dear Rahman
sorry for my bad english.Thank u for ur reply.jasjam freez on the first page!it mean i can not connect it to PC via active sync because it no load to windows!PC can not detect device!so how can i fix this problem without a PC connection ?