Database Users

Charging cable - Is it generic?

I'm in the UK and want to save $20 on the charger
I have a couple of Micro USB wall chargers that i use on my blackberry. They will fit the N1 and plug straight into the wall. Would they be safe to use, to charge my N1. (These charges are rated 750mHA).
I know the N1 will be supplied with a micro USB cable. I also have an IPhone wall socket plug head, the ones where you just put the USB cable into the plug and then it goes into the wall. Are these safe to use too, for charging the N1?
Thanks

the Nexus one connector is standar microUSB and therefore will work with standard microUSB cables and chargers.

So there is no type of resistor or transformer in the official plug head? ... to restrict power. I thought there would be as my blackberry charger has a 750mha rating on it.
I can understand the USB cable will work as its a limited power output from a laptop port. But just wanted to check the official wall outlet plug current isn't being restricted. The last thing i want to do is fry my new N1.
Cheers,

Just plugged mine into my old nokia classic micro usb and it is charging fine

The specs for the wall charger are 5V and 1A.
http://www.htc.com/europe/product/nexusone/specification.html

do what i did. remove the charger from your basket and use the supplied USB with an old htc charger if you have one. If not get one for a few quid from ebay why spend $20 when you can get one for $5 odd from the market/ebay.

I can only speak anecdotally, but I used a Blackberry Storm charger and nothing exploded

this mini, micro, A B stuff is annoying. to clarify for my simple mind, will usb cables that fit into my G1 fit into the N1? or is it a different size?

Last year, Micro USB was decided as the open standard for cell phone chargers, so this should be replacing Mini USB as seen on earlier phones (BlackBerries, G1) in instances where the port isn't.. some.. proprietary crap.
Edit:
j.books said:
this mini, micro, A B stuff is annoying. to clarify for my simple mind, will usb cables that fit into my G1 fit into the N1? or is it a different size?
Click to expand...
Click to collapse
No. The G1 used Mini USB, this is Micro USB. The phone comes with a charger and USB (USB-A 2.0 to Micro USB 2.0) cable.

It's not propitary so it will work with any other charger.

It's a funny thing to find. It's too new to be widely available
I went looking for a car charger and a straight USB A->Micro B cable. The former I found by poking in all the packages for different phones until I found it (found a Samsung charger that uses it, although they did want nearly £30 for the damned thing). The USB A->Micro B I drew a blank - the more clueless salesmen tried to convince me that I was mistaken and I meant Mini!
I thought the blackberry used them but I looked in the pile of blackberry cables the local shops had and they were all mini. Even my local electronics store has every kind of USB imaginable *except* micro.
Edit: Found one! (might be useful for UK users). It's out of stock though... http://www.cableuniverse.co.uk/catalog/cables/USB-A-to-Micro-USB-B-Cable.html

Just so you guys know, not all micro USB's are the same. I bought a car charger from a local Tmo store last week (I forget what phones it was for), and although it "worked" when the plug was perfectly perpendicular to the phone, it had quite a bit of lateral play (which the OEM plug does not), meaning anytime it moved in the car, it would stop charging.
I returned it, and am now just waiting for HTC to decide to manufacture accessories for this ever increasing bundle of worry...

I am using a TomTom charger for my N1, also the HTC hero and the Motorola Droid chargers works to charge my N1.

SANTilt said:
Just so you guys know, not all micro USB's are the same. I bought a car charger from a local Tmo store last week (I forget what phones it was for), and although it "worked" when the plug was perfectly perpendicular to the phone, it had quite a bit of lateral play (which the OEM plug does not), meaning anytime it moved in the car, it would stop charging.
I returned it, and am now just waiting for HTC to decide to manufacture accessories for this ever increasing bundle of worry...
Click to expand...
Click to collapse
Seems like it was just a poor quality charger. If it's a micro USB, it should be built to specific specifications. I already bought a few chargers (including a car charger) and cables (for work, home and travel), and they all work perfectly. Technically ALL micro USBs should be the same, unless the manufacturer didn't follow the standards.

TaFFeR said:
Seems like it was just a poor quality charger. If it's a micro USB, it should be built to specific specifications. I already bought a few chargers (including a car charger) and cables (for work, home and travel), and they all work perfectly. Technically ALL micro USBs should be the same, unless the manufacturer didn't follow the standards.
Click to expand...
Click to collapse
Hah, just my luck; I pick up the one out of spec micro USB charger in the entire city!
Although, it must be that particular T-Mobile supplier, as I went to another store and test fitted the same charger, and it had excessive wiggle as well. Either that or my phone is just lame...

I just got a universal charger in Tesco for £5 that has changeable heads (Micro, Mini, Samsung, Sony Ericsson and Nokia 2mm)
Works perfect

- The cable is standard USB. You can use it to charge the phone from your PC, or use another micro USB cable or charger you have
- The Nexus comes with a US 2 pin charger that is dual voltage - works in UK and US. Just spend 50p and get a US to UK convertor plug.
- The charger is rates 5v 1A, so if you have another microUSB charger with the same voltage use that.
I find charging from the charger results in more battery life than USB. The only explanation is charge rate because USB is 500mA and the charger is 1000mA
PS. I removed the UK charger from the order too. You get the US charger regardless in the box.

Evo 4g Touchstone wireless induction charging mod.

I recently got a HP Touchpad bundle and while the Touchpad is pretty darned decent and definitely worth a hundred bucks, what really impressed me was the touchstone charging dock. Its brilliant.
I looked into it and found the the palm pre also had this and some chap on the net had figured out how to shoehorn the unit into an evo.
I did the mod to mine and its amazing. No more charging cables. Yay!
This is my take on it - tutorial with pictures: http://asmd.wordpress.com/2011/09/26/evo-4g-wireless-induction-charging-modification/
This should come standard in all wireless devices!

Nice mod! Looks better and I'm sure doesn't fail as bad as the powermat charger.
Sent from my Gruesomes Rom using Tapatalk

Nice mod. Thanks for sharing.
via EVO.

Hi, this is a great mod!
Noob question: I noticed the charging light but the charging icon does not change on your screen. Just curious if once that the battery is completely charged, the icon will turn green. If so I wonder if the charging unit from the Pixi will stop charging the battery once it's full.
Also, compared to charging it directly from the AC Adapter, how long does it take to get a full charge? Is it the same aprox?
I'm planning on taking a look at my Inspire and see if the back cover allows me to put the charging unit there.
Thanks in advance

I did this about a week after launch. Very cool...but over time the novelty wore off.
I got sick of the bulge and ripped it out.

Nice! I wonder if I do the same with the Powermat case...
I have the Powermat, but the only caveat is that it requires a bridge connector between the case and micro-usb port.

haroldgv said:
Hi, this is a great mod!
Noob question: I noticed the charging light but the charging icon does not change on your screen. Just curious if once that the battery is completely charged, the icon will turn green. If so I wonder if the charging unit from the Pixi will stop charging the battery once it's full.
Also, compared to charging it directly from the AC Adapter, how long does it take to get a full charge? Is it the same aprox?
I'm planning on taking a look at my Inspire and see if the back cover allows me to put the charging unit there.
Thanks in advance
Click to expand...
Click to collapse
Im running MikG v2.5 Rom and the charging icon flashes between the lighting bolt charging icon and % so you can see at what % the battery is at while charging. When i took the picture, it was showing %, but rest assured it flashes between the two just as if it was plugged in the usb cable.
The Induction charging puck is dumb, it only supplies power much like a usb cable. The charging circuit in the Evo decides when the battery is fully charged and stops charging. The Evo for all intensive purposes acts and behaves exactly as if the usb cable was plugged in. It cant tell if power is coming from the puck or the usb cable. I wouldnt plug in the cable while its on the puck though. Although the voltage will remain the same, about 5 volts, the amperage will increase, a doubling in amperage shouldnt break anything but i havent found out the hard way.
The puck takes the same amount of time to charge as the usb cable. I havent seen any significant difference between the two.
There really isnt much of a bulge of the back case with using 30 awg wire. Just seat it flat and make sure nothing from the cover crimps on it, and its pretty much neat and tidy.
Ive seen this mod done with flat ribbon cable which would work just as well, although in not sure how it was routed through the phone.
regards,
asmd.

uniquenameevo said:
I did this about a week after launch. Very cool...but over time the novelty wore off.
I got sick of the bulge and ripped it out.
Click to expand...
Click to collapse
30 awg wire or flat ribbon cable solves the bulge problem. Ive got pucks everywhere, several at home, several at work... and its great not to have to plug it in.
It serves as my phone holder and charging unit. i've set the phone screen not to go to sleep while charging, so it makes for a nice display as well. With the screen left on, it does take longer to charge though.
regards,
asmd.

Yeah,
I did this a Loooooong Time ago using the Palm Pixi touchstone cover.
http://doesitpew.blogspot.com/2011/03/htc-evo-4g-mods-beyond-stock-and-one-of.html
Here is what it looks like with a custom clear back cover.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The Pixi cover is substantially thinner than the Pre cover and can be fit easily without bulge.
It actually held my phone up hovering in the car while driving.

jdgiotta said:
Nice! I wonder if I do the same with the Powermat case...
I have the Powermat, but the only caveat is that it requires a bridge connector between the case and micro-usb port.
Click to expand...
Click to collapse
Its been done. Apparently its quite easy to replace the powermat induction unit with the pixi unit. and the cover fits perfectly.
I opted not to get the powermat case as i wasnt keen on the bridge with the usb dongle sticking out the bottom.
Ive havent heard many good things about it, pretty much nothing but complaints about the powermat induction charging unit which is why i decided on this mod and i can tell you it works, it simply works, perfectly every time.
[/URL]
Uploaded with ImageShack.us[/IMG]
regards,
asmd.

What about adding a diode to prevent damage from accidentally plugging in USB while charging on the puck? I really like this mod great stuff...

Childofthehorn said:
Yeah,
I did this a Loooooong Time ago using the Palm Pixi touchstone cover.
http://doesitpew.blogspot.com/2011/03/htc-evo-4g-mods-beyond-stock-and-one-of.html
Here is what it looks like with a custom clear back cover.
The Pixi cover is substantially thinner than the Pre cover and can be fit easily without bulge.
It actually held my phone up hovering in the car while driving.
Click to expand...
Click to collapse
Nice work!!
I would love to know hwere you wired the pixi induction charger to?
Im really curious about what you said "Inductive charging back was wired into the test points for the USB power as opposed to attaching directly to the resistors as it is safer and easier to remove if there is an issue with the phone otherwise and needs servicing."

Well, this post finally got me moving on modding my Nexus S to charge via induction. I just got my HP Touchpad with the touchstone charging dock and it is very very cool. Can't wait to get my Nexus S that way too. And the Palm Pre/Pixi covers are pretty cheap. The Touchstone dock is only $8 too. I can have multiple units for work, home, relatives and will probably mod it to be in my Car phone holder. The possibilities are endless. Wish me luck.

Ok this power thingy(name doesnt come to mind) uses a cord to power it right so doesnt it defeat the purpose of being wirless if you know were im coming from. But hey I maybe wrong its probably battery powered? So dont sun me.

Awesome mod and comes in handy for me since my USB chord is lost most of the time lol

I have mine fitted with this case. It's a TPU plus hard plastic back. I have great phone protection and touchstone charging.... It's no more bulkier than any case out there.

asmd6230 said:
Nice work!!
I would love to know hwere you wired the pixi induction charger to?
Im really curious about what you said "Inductive charging back was wired into the test points for the USB power as opposed to attaching directly to the resistors as it is safer and easier to remove if there is an issue with the phone otherwise and needs servicing."
Click to expand...
Click to collapse
Actually...
This is easy to do since the screw hole surrounding areas are grounded = ground since its pretty universal in this phone, like most mobile devices.
There are a few test points next to the Micro USB port that you can directly test by simply plugging in a USB cable and "buzzing" for the connection of the 5v line.
I get your concern, but there really need not be one and these are the best spots to attach because they are the easiest and safest to remove later. Also, there is a regulator onboard with a shutoff/on ciruit within the inductive charging circuit. It will not turn on or allow voltage to pass under 4.5V (shuts off) from the outputs. Connecting the inductive charger to the 5V input line of the USB directly means that it treats it like USB charging. The onboard current and voltage regulators and charging circuitry of the Evo make it pretty darn hard to ruin it. At any rate, the inductive charger won't ever get up to 1Amp anyway because of power loss due to physics. It is pretty much 500ma in most circumstances from the Pixi receiving end.
The test points are far enough for skilled hands to hit with s solder braid or suck up after a rework airing anyway.
For those who skipped the technical mumbo jumbo, they basically made it impossible for you to screw up (unless you decided to connect your inductive charger at 5V to your Li-Ion battery at 3.7V - DO NO DO THAT!). The picture shows the wire going at the edges of the battery because that is the best place with room, they both route to the same hole at the back of the battery. Use 28AWG or 30AWG teflon-coated stranded wire for slimmest results. Great quality wire will mean that you don't have power loss (the traces are thinner than the wire is anyway so its not an issue).
If you have some detailed questions, post them up or send me a message. I will try to be prompt!

I remember last year when this mod first showed up, the addition of the Palm induction coil screwed up the evo's internal compass which then caused problems with navigation. Is this still an issue?

DroidFreek said:
Ok this power thingy(name doesnt come to mind) uses a cord to power it right so doesnt it defeat the purpose of being wirless if you know were im coming from. But hey I maybe wrong its probably battery powered? So dont sun me.
Click to expand...
Click to collapse
Ha. You are totally right, simply switching one wire for another. Then, if you need to usb mount or sync or whatever, you still need a regular micro usb cable to do so...
1 cable for plug/charge/sync
or
1 Charging stone for power
1 Regular cable for das syncing/usb mount/charge.
Hmmmm

jjvw said:
I remember last year when this mod first showed up, the addition of the Palm induction coil screwed up the evo's internal compass which then caused problems with navigation. Is this still an issue?
Click to expand...
Click to collapse
the induction coil and the metal discs in the phone are not magnetic. When off the charging puck, everything works like it should. Truth be said ive never used the compass app. (im not sure if i even have one), i exclusively use gps which works just fine.

Wall Charger For 10" Acer Iconia Tab A500 Power adapter

Wall Charger/ Power Adpater For Acer Iconia Tab A500 With 2M Cable
100% Brand New.
This the OEM Wall charger for Acer Iconia Tab A500 tablet pc for house using.
Input: 100~240V -0.65A 50/60Hz Max
Output: 12V 1.5A
Cable length: 2M (6.5feet) Special Design
Compatible with: Acer Iconia Tab A500 tablet pc
US plug version. It needs a plug converter for EU/AU/UK using.
Package Includes:
1 x wall charger for Acer A500
$12.99
http://witglobal.com/goods-3873.html

Thanks. I just ordered one. Shipping is free! But super slow... I'll drop a note when mine gets here and let you know how it fits.

I want one with a long cord. A lot longer.

Make one with a 10' cord and I'll buy.

mwm215 said:
Make one with a 10' cord and I'll buy.
Click to expand...
Click to collapse
This. I love my 15 foot HDMI cable, because I can now keep the tab closer to the wall charger and run the cable all the way to the TV.

mknewman said:
I want one with a long cord. A lot longer.
Click to expand...
Click to collapse
Want a longer cable? Get a 22awg cable and either solder or crimp positive negative and ground. I wouldn't go more than 20 feet max personally. And if you solder it make sure the three cables don't touch or it goes boooooooooom!
Sent from my A500 using XDA Premium App

Chargers do not work!!!
post man said:
Wall Charger/ Power Adpater For Acer Iconia Tab A500 With 2M Cable
100% Brand New.
This the OEM Wall charger for Acer Iconia Tab A500 tablet pc for house using.
Input: 100~240V -0.65A 50/60Hz Max
Output: 12V 1.5A
Cable length: 2M (6.5feet) Special Design
Compatible with: Acer Iconia Tab A500 tablet pc
US plug version. It needs a plug converter for EU/AU/UK using.
Package Includes:
1 x wall charger for Acer A500
$12.99
http://witglobal.com/goods-3873.html
Click to expand...
Click to collapse
So far this charger is NOT looking good.
I bought two 110 AC wall chargers and one 12v car charger and received them last night.
Plugged tablet in last night with 42% charge left in it, woke up this morning and tablet was dead.
Fully charged tablet with Acer stock OEM charger.
Used tablet until it was at 78%. Have been trying to charge all morning with one of the chargers with no luck. Now trying the other one to see it just the one is defective...
..but SO FAR, at least one of 'em is looking like a POS...
EDIT: so...BOTH of them fail to charge the unit. Plugged into wall - both of them will make the tablet think it's charging (icon changes to lightning bolt / charging icon) but there is NO POWER being added to battery. Battery will slowly discharge even when plugged into wall with these chargers.
STAY AWAY FROM THESE. I will now attempt to get my money back. I will keep you posted on my success or failure...P>S> Still have yet to test the 12v car adapter but confidence id NOT high...

Achristocat said:
So far this charger is NOT looking good.
I bought two 110 AC wall chargers and one 12v car charger and received them last night.
Plugged tablet in last night with 42% charge left in it, woke up this morning and tablet was dead.
Fully charged tablet with Acer stock OEM charger.
Used tablet until it was at 78%. Have been trying to charge all morning with one of the chargers with no luck. Now trying the other one to see it just the one is defective...
..but SO FAR, at least one of 'em is looking like a POS...
EDIT: so...BOTH of them fail to charge the unit. Plugged into wall - both of them will make the tablet think it's charging (icon changes to lightning bolt / charging icon) but there is NO POWER being added to battery. Battery will slowly discharge even when plugged into wall with these chargers.
STAY AWAY FROM THESE. I will now attempt to get my money back. I will keep you posted on my success or failure...P>S> Still have yet to test the 12v car adapter but confidence id NOT high...
Click to expand...
Click to collapse
Do you have a volt meter? I'm curious (and willing to bet) that it's not really providing 1.5A. The fact that it's terminating to a USB cable and the site claims that you can use "other power supplier and Car chargers with USB power delivery" (their spelling) raises a red flag. USB power is usually only 0.5A, and even on the high-end they only push 1A or 1.2A.... not enough for our tablet. My advice is to stick with the OEM chargers (Wal-Mart still has them for $14.95).
I got ripped off with a similar eBay purchase for a USB car charger that specifically said 1.5A.... only to find that my phone was loosing power when plugged in. After checking it out the thing was only pushing 200mA!

This is definately not oem, id just pony out the extra 3? dollars and buy the real one from walmart, youll probably spend the same on shipping this one

Modified the OEM charger with a cable from one of these POS!
Tried to contact the distributor to get my money back and SURPRISE...couldn't get a hold of 'em.
The good news is that I ripped out a cord from one of 'em and replaced the cord in my OEM charger and it's working SuperGood. Direct replacement!
...which is good, because the cord in my OEM charger was starting to fray right above the strain relief...They used Very Poor wire in these guys..
Anyway, glad these chargers are good for Something...

Cord length in these?
Sent from my A500 using xda premium

Cord Length of the POS..
The cord length is 6'6" long. A nice size...If only they worked...
Like I said in my other post, it made a great replacement cord AFTER I cracked one of these open and stole the cord for my tired OEM charger...
If you are thinking about buying - DON'T!
...unless you just can't find a replacement cable w/plug anywhere else and you are desperate...
They Do Not Work!!!

I can confirm that this does not work. But I am thinking about doing the same cord swap that you mentioned so it isn't a total loss for me either. Was worth a try for sure.

I too can confirm that this charger will not work. I got the exact same model off e-bay and it did supply the correct voltage, but I did not think to check the amperage at the time.
What was interesting is that the tablet reported as charging (the battery icon showed the lightning bolt), but it was actually depleting. This makes me think that it's totally a problem of not enough current.
The package I got included this charger with a car charger, which worked fine after some adjustment. So it wasn't a total loss.

Changin out the cord...
For those of you thinking about changing out the cord from the POS charger to the OEM charger, I have a few words of advice -
1) The case is glued together. There are no screws. Not under the stickers or under the plug plate. I took a very sharp, sturdy Strong knife and slid it into the seam and stuck it hard ALONG THE SEAM, not into the charger. The charger is PACKED with goodies and can be demolished easily.
2) Get a reading on polarity (center pin is What Color Wire?) BEFORE you unsolder either one. I did, but screwed up, forgot which was which but got lucky when I did my first re-solder of the wires. I did have a 50/50 chance..
3) After soldering the wires into place, hold the unit together and plug it in to your tablet to make sure it works BEFORE gluing the case back together. You know...to be sure and save your self some trouble...
4) I ended up hot gluing the case back together in case I need to take it apart again to replace the cord again. It's still sturdy as hell, but can be pryed apart Much more easily (while still being strong!) without destroying it.
5) This is a GREAT mod so far - The plug actually has a slightly longer center pin on it and stays in the socket on the tablet much easier than the stock right angle pin.
Destroy the POSand make it good for something... Good Luck!!!

I have a power cord for the gtab. Some voltage but the amp is 2. Will that still work ok our could that send too much power hurting the battery?
nvm plug too fat
Sent from my MB855 using XDA App

In fairness to the seller of this wall charger for the A500, I must tell you that I've received my unit today and plugged it in..........works flawlessly.
Perhaps they have changed their suppliers since last month?
Mag

Bump.
Anyone have any further experience with this charger? Is it worth buying?

OT but worth $40. http://www.amazon.com/Acer-A500-Doc...OUCO/ref=sr_1_1?ie=UTF8&qid=1335890930&sr=8-1
Charges, headphones or speakers, two stand positions, charges with the special dock.1/2 price and overpriced but great for watching movies with your headphones on. Now they need to put the newer 5foot cord in the package. Two models on Acer's site so maybe the newer one does?

post man said:
Wall Charger/ Power Adpater For Acer Iconia Tab A500 With 2M Cable
100% Brand New.
This the OEM Wall charger for Acer Iconia Tab A500 tablet pc for house using.
Input: 100~240V -0.65A 50/60Hz Max
Output: 12V 1.5A
Cable length: 2M (6.5feet) Special Design
Compatible with: Acer Iconia Tab A500 tablet pc
US plug version. It needs a plug converter for EU/AU/UK using.
Package Includes:
1 x wall charger for Acer A500
$12.99
http://witglobal.com/goods-3873.html
Click to expand...
Click to collapse
I brought one of Ebay (had pretty much exactly the same wording) and when it came it's only 4FT!.
http://www.youtube.com/watch?v=oKl7V4XWEMo
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

USB-C adapter

I have seen some comments and reviews that some USB-C cables are dangerous to use on our phones. Mainly the "Amazon Comment" from a Google Engineer who said that a particular USB-C cable could harm the device.
I am looking to buy some cheap Micro-USB to USB-C adapters for my current chargers, does anyone know if they are safe to use?
Is there a thread that has all the tested and confirmed cables, adapters and chargers? Seems this USB-C thing is more confusing than I though it would be.

I think you are better off buying a USB 2.0 Type A to Type C cable instead of a micro USB adapter. This one has been recommended:
http://www.amazon.com/iOrange-E-Braided-Reversible-Connector-ChromeBook/dp/B010VFFSL4/
Something like this is NOT compliant, according to the same Google engineer:
http://www.amazon.com/Adapter-TechMatte®-Convert-Connector-OnePlus/dp/B0151RKYBG/

bummer, I don't need "fast charging" all the time so I'm ok with standard charging speed for the most part. However I certainly don't want to "harm" my device with a cable or adapter that is not properly engineered.
Most if not all of the cables he recommends are around $20 for just a cable. Craziness...

I don't think you will damage the phone, but there's a risk you will damage the other side, i.e. charger or computer port. Now frying a $10 charger is not a big deal as long as you are not setting the house on fire, but frying a computer USB port is a different story ... that's what I'm really worried about.

I love how iOrange raised prices on their cables by $4-5 each. That's a 25% increase since gaining popularity yesterday.

Cares said:
I love how iOrange raised prices on their cables by $4-5 each. That's a 25% increase since gaining popularity yesterday.
Click to expand...
Click to collapse
Been steadily increasing since the engineer made his post. I understand, but on the other hand, I need a cable.

Cares said:
I love how iOrange raised prices on their cables by $4-5 each. That's a 25% increase since gaining popularity yesterday.
Click to expand...
Click to collapse
Good thing I ordered 2 the day the article came out. I thought they would raise prices with all the free publicity they got from the article.

What about those from one +? I bought a couple when they were in Stock

Cares said:
I love how iOrange raised prices on their cables by $4-5 each. That's a 25% increase since gaining popularity yesterday.
Click to expand...
Click to collapse
good enough reason for me to go with a different company. i hate when companies do that.

Rattles said:
good enough reason for me to go with a different company. i hate when companies do that.
Click to expand...
Click to collapse
https://www.monoprice.com/product?c_id=103&cp_id=10303&cs_id=1030319&p_id=13009&seq=1&format=2
If i you don't need 3.0 data speeds, thats the way to go. There is a google doc put together on reddit from all of Google engineer's comments/posts: https://www.reddit.com/r/Nexus6P/comments/3robzo/google_spreadsheet_for_usbc_cables_with_benson/

jsk23 said:
https://www.monoprice.com/product?c_id=103&cp_id=10303&cs_id=1030319&p_id=13009&seq=1&format=2
If i you don't need 3.0 data speeds, thats the way to go. There is a google doc put together on reddit from all of Google engineer's comments/posts: https://www.reddit.com/r/Nexus6P/comments/3robzo/google_spreadsheet_for_usbc_cables_with_benson/
Click to expand...
Click to collapse
Based on the photos, it seems identical to the cable Google sells. Wouldn't be surprised if they both came from the same place.

My question is this: why are people buying all kinds of usb-c to other versions of usb cables? The phone comes with everything one needs to charge or plug into a computer. Unless everyone wants cables for every room in the house...?

Rattles said:
good enough reason for me to go with a different company. i hate when companies do that.
Click to expand...
Click to collapse
wvcadle said:
My question is this: why are people buying all kinds of usb-c to other versions of usb cables? The phone comes with everything one needs to charge or plug into a computer. Unless everyone wants cables for every room in the house...?
Click to expand...
Click to collapse
I leave my stock charger in the living, but I want an adapter for overnight use to plug it in to my 2.4v Nexus 7 charger that stays in my bedroom.

jsk23 said:
I leave my stock charger in the living, but I want an adapter for overnight use to plug it in to my 2.4v Nexus 7 charger that stays in my bedroom.
Click to expand...
Click to collapse
The 6p comes with 2 cables already... One usb-c>usb-c and one usb-c>usb-a... So use the usbc/c cable for home and the usbc/a cable for travel.
Sent from my Nexus 6P using Tapatalk

wvcadle said:
My question is this: why are people buying all kinds of usb-c to other versions of usb cables? The phone comes with everything one needs to charge or plug into a computer. Unless everyone wants cables for every room in the house...?
Click to expand...
Click to collapse
Work, car, etc. I don't want to remember to take the charger/cable with me to work or in the car, I just want to leave them there. And the short cable that comes with the 6P is well ... too short. If you have a desktop computer sitting on the floor or want to charge from the wall or the car, it's just not good enough.

Fair enough!

inneyeseakay said:
The 6p comes with 2 cables already... One usb-c>usb-c and one usb-c>usb-a... So use the usbc/c cable for home and the usbc/a cable for travel.
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
This has nothing to do with travel. and the c-a cable it comes with is too damn short to use for much beyond data transfer. Unless the USB a charger is literally plugged in right next to where the phone is going to sit.

I'm trying to figure out how this new charging thing works as far as the required cable/charger.
I bought the iOrange-E cable from Amazon. http://www.amazon.com/iOrange-E-Braided-Reversible-Connector-ChromeBook/dp/B010VFFSL4/
I have a charger from my old Galaxy S4 that is 5V-1A. When I plug the iOrange in that charger and to my phone, it will say "Charging" but will not steadily charge. What I mean by that is that it'll change states to charging, then it'll stop charging, over and over again.
Another charger I have is 5 V - 2.1 A. With the iOrange cable, this works fine. It will say "Charging."
I have an Anker car charger. This is the one I have: http://www.amazon.com/gp/product/B00FYQKMRG?psc=1&redirect=true&ref_=oh_aui_search_detailpage
I'm not sure what the V/A is on that but with the included USB C -- USB A cable that was shipped with the Nexus 6P, it will charge.
I don't have the USB specs but does anyone know what the minimum is for simply "Charging"? How about "Charging Rapidly?"
I'm assuming my 5V - 1 A charger is too low since it doesn't seem to charge the 6P properly.

I saw the same thing with an HTC 1.5A charger. It charges for a few seconds and then it stops. Not sure what's going on, you'd think that it could at least pull the 500mA or 900mA per the USB spec. Another Anker charger that I have works.

I have this adapter Delmkin
It passes compatibility test using this app CheckR when hooked up with a tronsmart micro-USB cable.
Somebody mentioned that we have all what is needed inside the box and that's true and all but thing is most people don't want to carry their cables/chargers with them wherever they go. I have at least two charger with cables in each room of the house. One in each car and one at work. Makes it convenient since micro-USB cables/chargers are so cheap. Now with USB-C its a different story. One these cables are not cheap at all and now we are learning most of them aren't even complaint with the specs. So it helps to have a tiny adapter to be able to use all the cable I already own with Nexus 6P.

Special MicroUSB cable(custom made) - specifically for charging(ONLY)

Hi there guys,
Although active in the rom part of the 1+1 forum, I rarely spend any time in the general section and I thought why not post something? so a little backstory on the cable.
I want the fastest way to charge my phone and what can I do to improve that?
- Get a better charger
- Get a better MicroUSB cable
Our stock charger is capable of 5v 2.1A well the actual amperage it can give is less than 2A, I can't draw more than 1.8-1.9A on my phone even with my custom cable
So I got a quickcharge 2.0 charger just to try it and have a spare one, finally it became my main charger as it's rated at 5v 2A but actually can output 2.1A!!! phone is drawing that much, ranging from 2 to 2.1A - with stock cable it's a bit less than 2A but pretty close(around 1.97A to be precise)
So how's this custom cable I've build? it's like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
So it's a 18AWG and it's rated for "Maximum amps for chassis wiring: 16A" and "Maximum amps for power transmission: 2.3A" ..so it's capable of sustaining 2.3A without any problem(heat or power loss), if you use a very cheap microusb cable it can take up to 6 hours to charge your phone(as you can imagine the cable can play significant part) - Cable wire is of course copper so you know

Nice work, I've also noticed I get 1.6 to 1.8 amps on stock cable and charget

evronetwork said:
So it's a 18AWG and it's rated for "Maximum amps for chassis wiring: 16A" and "Maximum amps for power transmission: 2.3A" ..so it's capable of sustaining 2.3A without any problem
Click to expand...
Click to collapse
Very nice. Maybe a photo tutorial or youtube vid on construction?

naeem76 said:
Nice work, I've also noticed I get 1.6 to 1.8 amps on stock cable and charget
Click to expand...
Click to collapse
I'm close on stock(cable+charger)
pbergonzi said:
Very nice. Maybe a photo tutorial or youtube vid on construction?
Click to expand...
Click to collapse
I'm too lazy to do that hhahaa(as a computer tech guy I do many stuff and I have record many of my actions but I'm too lazy to edit my videos and post them online), but honestly trying to fit an 18AWG cable in a usb and microusb jack is pain in the a** because the wire is quite thick but it's an one time hassle, I permanently fix the wire(can't be removed even if I wanted to, the only way to fit new microusb and usb jacks is to cut the wire) - Trimming plastic inside the jacks without doing any damage just to fit the cable can be time consuming :crying:
Something that I didn't mention is the size of the cable, its the same size as stock
P.S. At best you'll find 20AWG cables in the market and some cost quite much

evronetwork said:
I'm close on stock(cable+charger)
I'm too lazy to do that hhahaa
Click to expand...
Click to collapse
Thanks. Really I was simply wondering to which contacts the wires went, but I'm sure the layout is on the web, and I'm probably not gonna do it anyway.

pbergonzi said:
Thanks. Really I was simply wondering to which contacts the wires went, but I'm sure the layout is on the web, and I'm probably not gonna do it anyway.
Click to expand...
Click to collapse
If you were close to me(same town or next one) I could do it for you for a small fee but don't do it if you're not very capable with ur hands and soldering iron
P.S. soldering them wrong can actually damage the phone permanently or even make the batter explode and/or charger(it's basically a short circuit) - you've been warned
My jacks are filled so after I solder the connections they can't be removed ..there are airtight also this cable is suitable if you use public chargers as no data would be "stolen" if one of the public chargers is modified - this uses only two wires and it's for charging

evronetwork said:
If you were close to me(same town or next one) I could do it for you for a small fee but don't do it if you're not very capable with ur hands and soldering iron
P.S. soldering them wrong can actually damage the phone permanently or even make the batter explode and/or charger(it's basically a short circuit) - you've been warned
My jacks are filled so after I solder the connections they can't be removed ..there are airtight also this cable is suitable if you use public chargers as no data would be "stolen" if one of the public chargers is modified - this uses only two wires and it's for charging
Click to expand...
Click to collapse
Nice work. Thank you. The data security is a nice feature.

pbergonzi said:
Nice work. Thank you. The data security is a nice feature.
Click to expand...
Click to collapse
On the bad side, if you need to transfer data you can't with this cable ..but I rarely use cable for data(I mostly use wifi connections to transfer data, or bluetooth) - Why? unessesary small-chargings will harm your battery, so if you connect the phone to your computer to transfer data better let it charge up rather than do your job and remove it, less than 1% charge frequent uses it will shorten ur battery life significantly
Even if I wanted to make it a full fledge cable with 18 AWG wire this is impossible, also it will become heavy for a usb cable. I barely fit 18 AWG cable(but it's capable of up to 2.3A(constant use)!! our phones can't draw 2.3A(no phone can ..at least not one I know) so it's great)
I wanted a wire with 2.1A constant use so it would have nearly no power loss(or voltage drop), putting a thicker wire won't make any different but 18AWG compared to stock, there's different. Especially if you compare a cheap 1 euro Chinese microusb cable with this one
--------
Although I'm really happy with my cable and it's my first pick when in hurry and need the faster charge available, two days ago the Chinese were celebrating something so I've bought cheaply(compared to original price) a Wsken magnetic micro usb cable(original), if you don't know whats that it's a microusb cable with magnetic tip. How does it work? check the picture:
I'll measure charging rates when received but I don't expect to be as good as my cable ..but in the night when in the dark a magnetic connection seems wonderful(also great if someones trip in the cable ..it won't make ur phone fall, it will be disconnected). If you put it backwards, it still works(but only for charging) so you can safely use it on public, just connect the cable in reverse. What's bad about this? well this comes with 2 microusb adaptors and one cable, you need that specific cable so if you have lots of devices you need to carry a cable with you(and it's not cheap) - Hope it has similar thickness as our stock cable so charging won't take long, can't wait 5 hours charging(as with some very cheap microusb Chinese cables)

Very good, thank you.

pbergonzi said:
Very good, thank you.
Click to expand...
Click to collapse
No need, we're a community and we help each other, in the future I may need ur help and/or knowledge

I'm a big numb-nut in terms of electrics, but when you're pushing the capabilities for charging, is there also an increased risk of damage?

experience?
evronetwork said:
On the bad side, if you need to transfer data you can't with this cable ..but I rarely use cable for data(I mostly use wifi connections to transfer data, or bluetooth) - Why? unessesary small-chargings will harm your battery, so if you connect the phone to your computer to transfer data better let it charge up rather than do your job and remove it, less than 1% charge frequent uses it will shorten ur battery life significantly
Even if I wanted to make it a full fledge cable with 18 AWG wire this is impossible, also it will become heavy for a usb cable. I barely fit 18 AWG cable(but it's capable of up to 2.3A(constant use)!! our phones can't draw 2.3A(no phone can ..at least not one I know) so it's great)
I wanted a wire with 2.1A constant use so it would have nearly no power loss(or voltage drop), putting a thicker wire won't make any different but 18AWG compared to stock, there's different. Especially if you compare a cheap 1 euro Chinese microusb cable with this one
--------
Although I'm really happy with my cable and it's my first pick when in hurry and need the faster charge available, two days ago the Chinese were celebrating something so I've bought cheaply(compared to original price) a Wsken magnetic micro usb cable(original), if you don't know whats that it's a microusb cable with magnetic tip. How does it work? check the picture:
I'll measure charging rates when received but I don't expect to be as good as my cable ..but in the night when in the dark a magnetic connection seems wonderful(also great if someones trip in the cable ..it won't make ur phone fall, it will be disconnected). If you put it backwards, it still works(but only for charging) so you can safely use it on public, just connect the cable in reverse. What's bad about this? well this comes with 2 microusb adaptors and one cable, you need that specific cable so if you have lots of devices you need to carry a cable with you(and it's not cheap) - Hope it has similar thickness as our stock cable so charging won't take long, can't wait 5 hours charging(as with some very cheap microusb Chinese cables)
Click to expand...
Click to collapse
Did you recieve this cable? I'd like to know your experiences. I know for a fact that the Znap cables are experiencing a lot of delay but there are a lot of Ebay clones on the market now.
Was going to buy this one but I have no clue if it works though.........

How do you measure the current drawn by the phone while charging?

BarnOwl said:
Did you recieve this cable? I'd like to know your experiences. I know for a fact that the Znap cables are experiencing a lot of delay but there are a lot of Ebay clones on the market now.
Was going to buy this one but I have no clue if it works though.........
Click to expand...
Click to collapse
Yes I receive the cable(if ur talking about the magnetic one) and charges up to 2.1A ..max amps for our phone
gyanbhartip said:
How do you measure the current drawn by the phone while charging?
Click to expand...
Click to collapse
Too many apps in the internet but I prefer the "Charger Timer", measures from 20% until 80% ..where the phone gets the "fastest" charging because when battery is low or way to high it draws less power(so battery will last longer)

gyanbhartip said:
How do you measure the current drawn by the phone while charging?
Click to expand...
Click to collapse
Thank you. I will give it a try for sure.
Sent from my A0001 using xda premium

gyanbhartip said:
How do you measure the current drawn by the phone while charging?
Click to expand...
Click to collapse
I've been using Amphere for a while. It works quite well.
https://play.google.com/store/apps/details?id=com.gombosdev.ampere&hl=en

evronetwork said:
Yes I receive the cable(if ur talking about the magnetic one) and charges up to 2.1A ..max amps for our phone
Click to expand...
Click to collapse
Thanks, that's what I wanted to know.....ordering one now.

Is this the magnetic one:
http://www.amazon.co.uk/gp/aw/d/B00VVJE6QS/ref=mp_s_a_1_1?qid=1453820974&sr=8-1&pi=SY200_QL40&keywords=Wsken&dpPl=1&dpID=31gh8cR4W7L&ref=plSrch
I've been after a new charger since my original one plus charger broke, been using a nexus 5 one instead.

Been using it for a while now, I got this one
I like it a lot! It even transfers data from and to my PC! I just have to make sure the led faces the bottom to transfer.
I do not know if it works on ALL oneplus ones as there seems to be a lot of difference in these devices, so don't take my word on it!
It also charges fast, just as fast as the original cable. I just ordered another one to use in my car.