Qtek 9090 WM2003SE
w$ xp into a virtualbox VM
Debian Sid
==================
Hi,
I followed the pages I found on this site and I downloaded the Windows Mobile 6.5 Pro Build 21169.5.0.0 - Release 3 (grandma_pics.zip), but I had a 150 error and now I'm stucked with a device saying SERIAL||USB on a white screen (depending if it is or not plugged into the craddle) not responding to any reset and not lighting.
activesync don't detect it anymore, so I suppose I'm doomed
Did the update start as it should? It should first detect your current software version and then ask you to continue. Then a progress bar would show and update would begin (taking about 5 minutes). Where exactly has it gone wrong? Don't be afraid (Sorry if my english is bad, I don't use it so often)
I followed the howto and upgrade started, but the bargraph didn't come and connexion was lost.
Then it thrown a 150 error, and since I'm stucked with the USB screen.
When I de/reconnect xp emits USB in/out sounds but activesync stays unconnected.
If you haven't seen this screen:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
then it's 99% safe to take out the battery With some builds I get an error while trying to start upgrade from 2003 to 6.x, so you might try another build... Hope this helps!!!! Good luck!!!
Unfortunately it didn't help: I'm still stuck with the SERIAL screen
Hard reset (in windows 2003 press Power + Reset)? Try upgrading to Win2003.
Nope: still stucked
When you run the 2003 upgrade, what does it say? Can't find the phone?
I just tried the hard reset.
I'll try 2003 tomorrow (its 0320 here!)
Thanks for your answers, I'll keep you posted ASA I tested the 2003 upgrade.
I succedd to flash it (well, almost
I reinstalled activesync and re-read the doc (that say I could be left w/o USB connectivity) and relaunched the upgrade (still WM6) and it worked...
mod'op:
* Uninstall AS (which failed, staying forever at "1 second left" (but remember: I use xp on a VM, on a slooow machine (XP2600+ w/ 1.5GB RAM),
* Uninstall the CE USB driver,
* Reboot xp,
* Reinstalled AS
Well, it worked until ~97%, and thrown a 112 error (CE ROM Update error); so, as adviced by the flasher, I performed a soft reset, get the 4 coloured stripes, pressed camera & voice, and I'm now stucked here: I've got the 3 options, but nothing seems to act on them (no moving between options, no change while screen-pressing more than 2s on the 1st or typing N on the keyboard.) - The device screen indicated 98%.
So, now guess I must re-upgrade, but as I don't want to end up with a paper-weight, I'll wait for skilled advice.
HankHulator said:
I succedd to flash it (well, almost
I reinstalled activesync and re-read the doc (that say I could be left w/o USB connectivity) and relaunched the upgrade (still WM6) and it worked...
mod'op:
* Uninstall AS (which failed, staying forever at "1 second left" (but remember: I use xp on a VM, on a slooow machine (XP2600+ w/ 1.5GB RAM),
* Uninstall the CE USB driver,
* Reboot xp,
* Reinstalled AS
Well, it worked until ~97%, and thrown a 112 error (CE ROM Update error); so, as adviced by the flasher, I performed a soft reset, get the 4 coloured stripes, pressed camera & voice, and I'm now stucked here: I've got the 3 options, but nothing seems to act on them (no moving between options, no change while screen-pressing more than 2s on the 1st or typing N on the keyboard.) - The device screen indicated 98%.
So, now guess I must re-upgrade, but as I don't want to end up with a paper-weight, I'll wait for skilled advice.
Click to expand...
Click to collapse
Why upgrade with a VM?? And why so an old ROM
With a VM because I don't have anymore w$ directly acessible (and don't want it, as I've got small HDz)
I thought the howto pages where up to date...
Anyway, I re-put the device into flashing mode and it is upgrading at this time.
I'll keep you posted of the result; but I just read the links you sent and I think I'll go to 6.1 as you say the battery life is much longer (but I don't know exactly how to do that, as it will be a downgrade.)
And about the support, I'd have been glad to do so, but I can't (I'm unemployed and been given this device, which, I hope will help me to launch a small business till the next january)
Failed @ 29% this time.
I'm currently downloading the WM6.1 version
After several attempts and many 112 errors (@ random upgrade %ages, may be low level USB interractions?) I'll try tomorrow on a pristine XP installation (friend's computer).
And keep you posted.
Taleb504
HankHulator said:
I succedd to flash it (well, almost
I reinstalled activesync and re-read the doc (that say I could be left w/o USB connectivity) and relaunched the upgrade (still WM6) and it worked...
mod'op:
* Uninstall AS (which failed, staying forever at "1 second left" (but remember: I use xp on a VM, on a slooow machine (XP2600+ w/ 1.5GB RAM),
* Uninstall the CE USB driver,
* Reboot xp,
* Reinstalled AS
Well, it worked until ~97%, and thrown a 112 error (CE ROM Update error); so, as adviced by the flasher, I performed a soft reset, get the 4 coloured stripes, pressed camera & voice, and I'm now stucked here: I've got the 3 options, but nothing seems to act on them (no moving between options, no change while screen-pressing more than 2s on the 1st or typing N on the keyboard.) - The device screen indicated 98%.
So, now guess I must re-upgrade, but as I don't want to end up with a paper-weight, I'll wait for skilled advice.
Click to expand...
Click to collapse
hey there i have the same problem as u . but i dont know what to do ... so plz if u can explain to me what to do ... and which files must use """sorry for my english """".
Yeahhh! The beast is beautiful!
PB was apparently that USB doesn't like very much my VM (or vice versa): it worked @ 1st try with a real xp.
However, 1st boot (after the 3 options setup in color bars) was triggered by MAIL+POWER, not MAIL alone (genuine Qtek 9090).
To aboutaleb504: Use a real w$, not a VM; and use the files pointed at in the 2nd link of D-2's post (I also took Office from a WM6.5 BlueAngel wiki's page and its working correctly)
Thanks to everybody tout le monde, and especially to D-2 for pointing the faulty VM and for the WM6.1 links
Please "D-Two" not "d-2" Thanks
You have seen that i have many Roms not only WM6.1
Ach, you D-Two
Yep, but I also read the docs and they say WM6.1 has the lowest battery consumption, which is important to me. That's why I choose to stick with it.
Ho-hO, Its a good thing this thread continues: I installed the 'cabs' and 'cabs2' packages I originally found with the first ROM image, and I just found that 'VoIP Setup' throw me an error:
"The file 'SetupVoIP' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling this file."
I reinstalled it but it was the same.
I'm glad you did it!! New Windows has much better functions, but I just got back to 2003, couldn't take the slowness anymore
HankHulator said:
Ach, you D-Two
Yep, but I also read the docs and they say WM6.1 has the lowest battery consumption, which is important to me. That's why I choose to stick with it.
Ho-hO, Its a good thing this thread continues: I installed the 'cabs' and 'cabs2' packages I originally found with the first ROM image, and I just found that 'VoIP Setup' throw me an error:
"The file 'SetupVoIP' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling this file."
I reinstalled it but it was the same.
Click to expand...
Click to collapse
Please give me the link...
Related
hello every one
i'm noob & i speak french so excuse me if my it's a lil bit hard to on understand my topic .
-after installing WM6 on my qtek 9090 i flowed the steps and then at the end
when i press the mail button the white screen appear & it still (when "welcome... " is supose appear after 30sec.
when i reset i see the bootscreen (clored stripes),i folow the steps but it still blokeded on the withe screen.
& i tried using others wm6 rom but the problem still the same
So i wanted to know if there is away to fix it??
-I tried to downgrade but it doesn't because i don't use the good rom i think.
what can i do??
-i have no acces to ppc from actyvesync
in boatloder it show v 1.02 & the 3 colors band shows :
NO GSM
D 6.00.00.WWE
thanks for your help
There is no problem with your BA. Try to do the setup again...
NOW....
Before you upgrade your BA keep this is mind...it's a warning...a WARNING so you will not sue xda-dev or any BA ROM cooker if something BAD happens to your BA. But don't worry 1 out of 1000 BA owners brick their BA while upgrading. Because they upgrade their BA with 10% battery life. Where did I get the 1 out of 1000 statistics? Just a guess..a wild guess but it's near to reality
WARNING
IF YOU PROCEED, YOU MAY TOAST YOUR PHONE. THERE'S NO COMEBACK. THERE'S NO GETTING ROUND THIS. READ THE INSTRUCTIONS FIRST OTHERWISE YOU'LL PROBABLY BREAK YOUR PHONE PERMANENTLY. THIS WILL VOID YOUR WARRANTY. DO YOU UNDERSTAND? DO YOu? ANSWER ME YOU...lol
Click to expand...
Click to collapse
- Download unlocker.cab DOWNLOAD HERE
- Download Repart_Doc.exe DOWNLOAD HERE
- Place both of them somewhere on your Pocket PC. For example in \temp but anywhere is fine. All the command below are to be executed on your Pocket PC, not on your PC.
- Install xda-developers_Unlocker.CAB by tapping on it in filemanger (from the directory where you put it earlier)
- Then go to start -> Programs -> ExtROM tools -> then first run "unhide", then "Unlock".
- Do a soft reset. (you know how to do a SR, right?)
- Once your Pocket PC is restarted, locate the Repart_DOC.exe file with your filemanager and start it.
- Set the size of Extended ROM to 128 kb (which is already the default).
- Press "Format now!" and wait until it is done (A few seconds). You will see a message that it is done. (You will get an error message about your storage, just press yes and wait a few seconds.)
- Soft reset your Pocket PC.
NOW YOU ARE DONE WITH THE FIRST PART AND I HOPE I AM MAKING IT EASY FOR YOU AND FOR EVERYONE.
Now, I RECOMMEND you to use Windows XP and of course Active Sync 4.5.
NOTE: Do a hard reset first
Doing a hardreset is easy if you have 3 hands - push your stylus at the softreset hole and then as soon as you see the Strips
hold Camera and Record
Then you will be a debugger screen
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Navigation in menu is done with camera and record buttons.
reset registry and format built-in storage
“Enable KITL” must be NO “Clean Registry Hive” must be YES “Format Storage” must be YES exit - "mail" button
You will know if you have performed a hard reset if you are lead through the setup of your device section. All else is just a softreset.
Click to expand...
Click to collapse
1. Download the BA ROM that you desired. It can be WM6, WM6.1 or WM6.5 and you can find all the download links of this ROMs on our BA wiki (and I am the one who updated that and put those links.)
2. Save that ROM on your computer. (anywhere will do) If it is zipped or rar, then unzip it or unrar it.
Here are the files that should be inside that ROM folder (well this are the files that I have every time I flash my BA, just correct me guys if some of this are not really needed):
EnterBL.exe
GetDeviceData.exe
HTCRUU.dll
RUU.dll
BaUpgradeUt.exe
MaUpgradeUt_noID.exe
HTCRUU.conf
RUU.conf
vbscript.dll
nk.nbf
SetOperator.bat
3. Temporarily remove your SD Card (it may work for you with the SD card still in your BA, but you may not be able to enter USB mode when cradled).
Just remove your SD Card from you BA and the SIM card too just to make sure.
4. Put your device into Bootloader mode by pressing and holding the "Power" & "Record" buttons, and then press the Reset Button. Ooops before I forgot make sure you do a Hard Reset on your BA first.
Press and hold the "Power" & "Record" buttons, and then press the Reset Button until “Serial” shows on screen.
(Some BlueAngel shows "Serial" at the top and "V2.07" at the bottom.)
NOTE: The screen will not be backlit, so it may appear the phone is not in bootloader mode.
Look carefully.
When the USB sync cable is inserted into the phone and the computer, "Serial" will change to "USB", provided that the phone detects the connection.
5. Connect the phone to the sync cable/cradle.
7. Now you can execute the installer file. (BaUpgradeUt.exe or MaUpgradeUt.exe) You will see this window:
8. When the upgrade is completed, you must perform a Hard Reset.
When the bootscreen, aka. the colored stripes is displayed, wait more, you are booting. The welcome screen to set up your device will appear shortly ...
thanks but there is a problem i have no acces to ppc from my computer & actvivesync dont localize it.
try THIS method, there is no need to reflash, you canceled the hard reset and now the things are f***ed up. so if another button hard reset does not help then MTTY method is your only hope
i did what the tutorial says but when mtthy i don't know wht to do cuz it don't correspond whit the tutorial
azdd said:
i did what the tutorial says but when mtthy i don't know wht to do cuz it don't correspond whit the tutorial
Click to expand...
Click to collapse
in port select USB or WCEUSBXXXXXX
& where must I type ???
azdd said:
& where must I type ???
Click to expand...
Click to collapse
In the MTTY window
i see USB i click on it & then i have a windows it's look like a text editor.then i type for exmeple "set 140" but after that i dont know what to do i tried autodownload but i got a msg like "input full name...."
so wht's the next step??
red_hanks said:
1. Download the BA ROM that you desired. It can be WM6, WM6.1 or WM6.5 and you can find all the download links of this ROMs on our BA wiki (and I am the one who updated that and put those links.)
2. Save that ROM on your computer. (anywhere will do) If it is zipped or rar, then unzip it or unrar it.
Here are the files that should be inside that ROM folder (well this are the files that I have every time I flash my BA, just correct me guys if some of this are not really needed):
EnterBL.exe
GetDeviceData.exe
HTCRUU.dll
RUU.dll
BaUpgradeUt.exe
MaUpgradeUt_noID.exe
HTCRUU.conf
RUU.conf
vbscript.dll
nk.nbf
SetOperator.bat
3. Temporarily remove your SD Card (it may work for you with the SD card still in your BA, but you may not be able to enter USB mode when cradled).
Just remove your SD Card from you BA and the SIM card too just to make sure.
4. Put your device into Bootloader mode by pressing and holding the "Power" & "Record" buttons, and then press the Reset Button. Ooops before I forgot make sure you do a Hard Reset on your BA first.
Press and hold the "Power" & "Record" buttons, and then press the Reset Button until “Serial” shows on screen.
(Some BlueAngel shows "Serial" at the top and "V2.07" at the bottom.)
NOTE: The screen will not be backlit, so it may appear the phone is not in bootloader mode.
Look carefully.
When the USB sync cable is inserted into the phone and the computer, "Serial" will change to "USB", provided that the phone detects the connection.
5. Connect the phone to the sync cable/cradle.
7. Now you can execute the installer file. (BaUpgradeUt.exe or MaUpgradeUt.exe) You will see this window:
8. When the upgrade is completed, you must perform a Hard Reset.
When the bootscreen, aka. the colored stripes is displayed, wait more, you are booting. The welcome screen to set up your device will appear shortly ...
Click to expand...
Click to collapse
thanks but the first time i did the upgrade i started directly instaling the rom & i didn't do the previous steps in the PPC maybe tha's why, i can't no longger than the white screen is it possible??
WTF you use autodownload for ?
execute the listed commands only, then reset and then reflash the rom you want, it is that simple, and everything is covered in WIKI with a WIZARD
it is explained very well there, just don't skip any step and you will be all right
thanks xplode it worked & thank to u all
glad it helped
I am trying to install HardSPL for the first time on my Hermes using MrVanx's guide at http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26
I followed all the steps, i downloaded olipro 2.10 extracted the files, plug in my fully charged hermes, watch the connection dialog complete successfully on the phone and sync center syncs and shows that the phone is connected, then i run RUUWrapper.exe and click next until i get to this screen:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I click update and then i click next twice to proceed with the flash. Then a message pops up on my pc that says "Verifying information on your Hermes please wait", and a dialog box pops up on my hermes asking me if i want to allow EnterBL.exe to run. I choose "Yes" and it enters this screen:
This is where my problem occurs. Once that bootloader screen shows up on my phone, the HardSPL update utility on my pc loses the usb connection, sync center no longer recognizes the phone as being connected, and the HardSPL update utility gives me the following error message:
ERROR [260] : UPDATE ERROR
The update utility cannot connect to your PDA phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone.
Check the following:
1. The PDA Phone is connected to the USB cradle/cable.
2. The USB cradle/cable is connected to the PC.
The bootloader screen on the phone just sits there ive tried mashing buttons but it does nothing, if i pull out the usb cord from the phone it will say serial at the bottom but thats about the most response i can get out of it. So basically i just restart the phone after to find that nothing has changed and try over and over again.
NOTE: I do not have an SD card in my phone, i dont know if this updater requires an SD card to be inserted but it never said anything about SD cards in the guide so i am assuming it doesnt matter. Also my bootloader screen does not totally match the picture it says:
HERM200
IPL-SSPL by Des
HERM200
SPL-1.09.ds
Not sure what that means or if it makes a difference either...
OK, you now have Soft SPL on your Hermes, follow these instructions EXACTLY...
1. Format an sd card (2Gb or less) FAT32. Copy .nbh file to it.
2. Rename .nbh file to hermimg.nbh . Insert into Hermes.
3. Reset into bootloader (tri-colour screen). If you did this right, follow the onscreen instructions...
This will be quick.
Once you have Hard SPL on your Hermes, your IPL will be 1.04 and your SPL will be 2.10 oli. Then you can use those steps to flash another rom. This was only possible because you have Soft SPL on your Hermes. If you want to flash another Hermes you should check out and follow the instructions on page 116, post 1160 of the Hard SPL thread...
Cheers...
If you have XP on your PC, upgrade your .net framework to 3.5.... That should also fix up that pesky sync error...
Are you sure i have softspl on my hermes? It seems like it might be the upgrader might just be temporarily loading it into the memory. I bought this phone used but its running WM5 and i doubt the previous owner would have installed softspl. Either way if i do have it permanently installed on the phone i dont know how to enter the bootloader without running that HardSPL upgrader. I will try what you said though. I dont have an SD card as of yet but i will pick one up today. And I am running Vista, but have read a few posts by Mr Vanx saying that Vista can have issues with these things. Ill get back to you after i get an sd and try it out.
nodyarg said:
............. i dont know how to enter the bootloader without running that HardSPL upgrader.
Click to expand...
Click to collapse
Press down both the POWER button and SIDE OK together and using the stylus at the same time to press the RESET button at the bottom.
Mike
Oh alrite cool thanks mike that is taking me to the bootloader. When i get my sd card ill try what ultramag69 said. Btw is the bootloader actually supposed to do anything other than display that screen? because i cant actually boot from it... i cant actually do anything in it....ive pressed every button on the phone nothing happens....
Anyways i guess that doesnt really matter at this point, ill get back to you guys after i have the sd card. thanks guys.
When you insert the sd card, as long as you've done the steps correctly, it will recognise the flash file on the card and do something. When you reset into bootloader, if you're worried Soft SPL is no longer on your Hermes, reset to bootloader before inserting the sd card. It should say SPL : 1.09 des. Insert sd card then reset to bootloader again.
If for some reason its not there, go to here - http://forum.xda-developers.com/showthread.php?t=296722
post 1160, page 116. You can download it (SSPL.exe), put it onto your Hermes main memory, do not run it from sd card, and run using the file explorer. It will start Soft SPL again. And as long as you have the flash file (hermimg.nbh) on the sd cards root directory, it well flash the Hermes.
Cheers...
ok so i got a 1gb microsd card and formatted it in fat32. i downloaded Hard-SPL-V7.zip, renamed RUU_signed.nbh to hermimg.nbh and then placed it on the root of the memory stick. Then in order to check my spl and ipl; i pressed down both the POWER button and SIDE OK together and using the stylus at the same time to press the RESET button at the bottom. It showed that i had IPL-1.01 and SPL-1.11, (which i am assuming means no softSPL). So then i downloaded SSPL-HERM.zip from page 116 post 1160 @ http://forum.xda-developers.com/showthread.php?t=296722 and i copied the SSPL-HERM.exe to the memory of my phone and ran SSPL-HERM.exe from file explorer. This took me into the bootloader which now said i had IPL-SSPL by Des and SPL-1.09.ds which i am assuming means softSPL. At this point i inserted my SD card. Nothing happened. So i pressed down both the POWER button and SIDE OK together and using the stylus at the same time to press the RESET button at the bottom, and my phone rebooted back into windows mobile. The SD was still in the phone but still nothing was happening so i rebooted back into bootloader mode AND MY IPL WAS BACK TO IPL-1.01 MY SPL BACK TO SPL-1.11!!! WTF AM I DOING WRONG?!!!
UPDATE: Now i am getting an error every time i try to execute SSPL-HERM.exe "The file cannot be opened. Either it is not signed with a trusted certificate or one of its components cannot be found". I am getting pretty sick of windows mobile 5 maybe i would have better luck getting hardSPL on if i upgraded to an official wm6 rom first. Do you still need hardSPL if you are using an official WM6 rom? because i think i saw an official european version of WM6.1 for the hermes somewhere in this forum. Maybe i could install that and i would have less problems trying to install hardSPL after?
alrite im going to assume that everyone is stumped by the problem so im thinking that i could flash my device with a ROM accepted by standard bootloader as it says in the SSPL-HERMES readme. im asuming i have somehow corrupted my hermes so once i do that everything will be reset to normal and i can start from the beginning and try again. so can anyone confirm for me that i can download a firmware somewhere that is accepted by the standard bootloader and flash my hermes without having to use HardSPL or softSPL and without any great risk? and if so can anyone recommend a firmware that i could do this with??
restart the hermes, have the sd card already inserted and run SSPL.exe from the main memory. It should work. If you think it may help, re-copy SSPL.exe back onto main memory.
nodyarg said:
ok so i got a 1gb microsd card and formatted it in fat32. i downloaded Hard-SPL-V7.zip, renamed RUU_signed.nbh to hermimg.nbh and then placed it on the root of the memory stick. Then in order to check my spl and ipl; i pressed down both the POWER button and SIDE OK together and using the stylus at the same time to press the RESET button at the bottom. It showed that i had IPL-1.01 and SPL-1.11, (which i am assuming means no softSPL). So then i downloaded SSPL-HERM.zip from page 116 post 1160 @ http://forum.xda-developers.com/showthread.php?t=296722 and i copied the SSPL-HERM.exe to the memory of my phone and ran SSPL-HERM.exe from file explorer. This took me into the bootloader which now said i had IPL-SSPL by Des and SPL-1.09.ds which i am assuming means softSPL. At this point i inserted my SD card. Nothing happened. So i pressed down both the POWER button and SIDE OK together and using the stylus at the same time to press the RESET button at the bottom, and my phone rebooted back into windows mobile. The SD was still in the phone but still nothing was happening so i rebooted back into bootloader mode AND MY IPL WAS BACK TO IPL-1.01 MY SPL BACK TO SPL-1.11!!! WTF AM I DOING WRONG?!!!
UPDATE: Now i am getting an error every time i try to execute SSPL-HERM.exe "The file cannot be opened. Either it is not signed with a trusted certificate or one of its components cannot be found". I am getting pretty sick of windows mobile 5 maybe i would have better luck getting hardSPL on if i upgraded to an official wm6 rom first. Do you still need hardSPL if you are using an official WM6 rom? because i think i saw an official european version of WM6.1 for the hermes somewhere in this forum. Maybe i could install that and i would have less problems trying to install hardSPL after?
Click to expand...
Click to collapse
What you did wrong was to insert the microsd card after you execute SSPL-HERM.exe. The card must be inserted before execution of softSPL. Then the phone goes to bootloader screen and will recognize the image in the card and will flash it after a prompt to continue.
This thread http://forum.xda-developers.com/showthread.php?t=295735 has a very good discussion about SD card method for flashing ROMs and the procedure its exactly the same for HardSPL flashing.
About the error with SSPL-HERM.EXE try copying the file again to your main memory or rename the file it might help.
HTC Tytn
SuperCID
SPL: 2.10.Olipro (HardSPL v7)
ROM: Shamanix WM6 Ultimate v2 Final
RADIO: 1.48.00.10
the problem has been mostly solved. I've managed to get hardspl on the phone by using v9 instead of v7. I think the problem I was having with v7 was that my phone won't run any roms that force sspl. v9 gave me an error but according to boz over at 4win it is a common error happens even during a successful installation. so after getting v9 on my computer the sspl-herm was able to flash and indicated a successful installation. after that I was able to flash black satin. black satin would not install through sspl so others with the same problem will probably have to choose the 2.10 new bootloader in order to get the flash to start. that's what worked for me anyways. I still don't understand why roms won't work thru sspl on my hermes but I have hardspl and black satin now so if I never figure it out I don't really care. thanks for your help guys I really appreciate it. its good to finally be on wm6
Hey, just got my x8 Briked, stuck at the SE boot logo.
Can't go to the xrecovery menu ... help ?!
ROM used was jerpelea's v003, got the " SD safe to remove " reboot then stuck.
Reinstall system with SEUS or PC Companion or with FlashTool
Pc Companion cannot connect to my phone.
I'll try SEUS ( downloading version 2.7 atm ).
If it fails to, let's go try FlashTool then, it's available from jerpelea's ROM packages, right ?
Thank for reply !
Just repair/update as dbts25 said, or try again to get in xrecover menu, maybe it start ...
...if your phone restart, pc cant make a connection. U have to start your phone from flash,
Connect the cable, open your phone and hold down back button to connect it...
Try it!
Yes it can be there. I don't download his ROM yet so I don't know
PC Companion = Fail
SEUS = Fail
FlashTool = Fail
Edit : Any other solution or links for your FlashTool & SEUS versions which I might try
First of all, do not panic (i say that because i was in panic myself the first time i bricked my phone).
I suggest you to install the stock rom from pc companion (then install what ever you want). You will LOOSE ALL your data (exept the ones in your SDcard), but it's better that a bricked phone
PC companion will work, follow the steps:
1. Go to "Support Zone" (in Pc Companion)
2. Click "Start" (without to connect the phone)
3. A window will pop up, click the "Repair phone" link
4. Click "continue"
ATTENTION: Somewhere here the program will ask you to choose you phone, i can't tell when because i have choose mine the first time i did it. After this it will ask you to connect it pressing the "Back" button.
5. A window will pop up to inform you somehow that you will lost you data, ckeck the box and click "next"
6. The PC Companion will download the final version of your stock rom, just wait... and then it will install it.
(the phone will connect throught flash mode)
P.S.:This will work, that's how i fixed my X8 when i had the same problem...
I hope that i helped you
EDIT: Write to jerpelea about the bug so he/she can fix it.
GreatApo said:
First of all, do not panic (i say that because i was in panic myself the first time i bricked my phone).
I suggest you to install the stock rom from pc companion (then install what ever you want). You will LOOSE ALL your data (exept the ones in your SDcard), but it's better that a bricked phone
PC companion will work, follow the steps:
1. Go to "Support Zone" (in Pc Companion)
2. Click "Start" (without to connect the phone)
3. A window will pop up, click the "Repair phone" link
4. Click "continue"
ATTENTION: Somewhere here the program will ask you to choose you phone, i can't tell when because i have choose mine the first time i did it. After this it will ask you to connect it pressing the "Back" button.
5. A window will pop up to inform you somehow that you will lost you data, ckeck the box and click "next"
6. The PC Companion will download the final version of your stock rom, just wait... and then it will install it.
(the phone will connect throught flash mode)
P.S.:This will work, that's how i fixed my X8 when i had the same problem...
I hope that i helped you
EDIT: Write to jerpelea about the bug so he/she can fix it.
Click to expand...
Click to collapse
Ok, I think I know why I can't repair..
Take a look at this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
( can't give you the full link because I'm new, delete the space between, sry for the inconvenience ).
It seems like my computer is missing the SEMC USB Flash drivers.
I get them from the net but the .inf driver file wont install..
ok, let's see... 2 suggestions (try second first)
1. First of all try to download and install "Gordons Gate". It installs the drivers BUT i was using it for my old phone (SE s500i, it's not a smartphone). I do not know if it will works...
2. Else, I can provide you my "Drivers" folder from my PC Companion folder. Copy your Drivers folder to desktop first (to have a back up), and then extrack my zip file in the "C:\Program Files\Sony Ericsson\Sony Ericsson PC Companion" or where ever you have your PC companion installed. (i think now it will not ask you to choose you phone)
Drivers.zip (download from mediafire)
I asume you have windows. I wish i works...
Thank you sir !
Solved my drivers problem with an other version of Gordon's Gate !
I had the 2.2.0.10 > uninstalled then reinstalled the 2.2.0.5 then worked fine !
Now I can repair my phone !
Thanks again ! <3
alextothex said:
Thank you sir !
Solved my drivers problem with an other version of Gordon's Gate !
I had the 2.2.0.10 > uninstalled then reinstalled the 2.2.0.5 then worked fine !
Now I can repair my phone !
Thanks again ! <3
Click to expand...
Click to collapse
Do not call me sir...i am only 18 .
So "Gordon's Gate" is still working... nice...
EDIT: I use v2.2.0.0, it works too
Flash TA by omnius HOw you wat i can upload my TA backup
zxc79 said:
Flash TA by omnius HOw you wat i can upload my TA backup
Click to expand...
Click to collapse
Why would he flash TA? It's not smart idea because Omnius can't recalculate sec. zone so he would end up with REALLY bricked phone...
Sent from my X8, so sorry for gramatical inaccuracy
alextothex said:
Thank you sir !
Solved my drivers problem with an other version of Gordon's Gate !
I had the 2.2.0.10 > uninstalled then reinstalled the 2.2.0.5 then worked fine !
Now I can repair my phone !
Thanks again ! <3
Click to expand...
Click to collapse
OOT: i think greatapo deserves to get thanks.
Hi there, I also bricked my x8. I messed up with the build.prop file and now i think PcCompanion "sees" it as an x10 device.It doesn't go any further than Sony Ericcson logo and I have to remove the battery to make it start.
I tried the above method of restoring it but SEUS says there isn't any software available.
SEUS just checks and then tells me there are no updates available.
Any ideas?
hazopoulis said:
Hi there, I also bricked my x8. I messed up with the build.prop file and now i think PcCompanion "sees" it as an x10 device.It doesn't go any further than Sony Ericcson logo and I have to remove the battery to make it start.
I tried the above method of restoring it but SEUS says there isn't any software available.
SEUS just checks and then tells me there are no updates available.
Any ideas?
Click to expand...
Click to collapse
Try the repair solution i have post above. Go to update with pc companion but do not connect your phone to the pc, a window will pop up. Click repair and folow the instuctions...
Yours, GreatApo
(Sent from my Xperia X8)
Thanks for the reply GreatApo.
When I try the repair solution i get the message: "there is no software available for your phone yet.Please try again later". As I recall now, I changed the build.prop with one of X10 device and when I recovered the backup something went wrong (maybe i erased it?!)
So now neither SEUS nor X10FlashTool can do anything. Is there a way to restore build.prop?
edit: I just had another idea. Is there any way to mesh up the phone even more so it doesn't see it as an up-to-date x10 and DO the repair?
Sony Ericsson doesn't really have a flashing tool, does it?
It's my solution.
1. Download flashtool with orginal rom 2.1 and drivers from rapidshare.com/files/451848208/flashtool.rar
2. Unpack
3. Install drivers if U need
4. Open X10flash.bat
5. choose your operating system
6. connect phone to flash mode
7. on PC click any key
8. wait for finish flash
9. enjoy your working phone
hazopoulis said:
When I try the repair solution i get the message: "there is no software available for your phone yet.Please try again later".
Click to expand...
Click to collapse
I thing that repair does not search for an update, it just download the latest official rom. try the other people suggestions... there must be a solution.
Again, thank you for the replies.
I tried flashtool through X10flash.bat but I couldn''t get past the selection of OS. Is there a difference with the GUI version of flashtool? Using GUi version, everytime it started flashing it gave me an error and never finished flashing.
I also thought that repair from Pc Companion would and SHOULD do the job but as it turns out it isn't a repair tool after all.
Anyway, I finally sent it to service 'cause I need it soon.
Bottom line: Be careful when messing with build.prop ! : )
I flashed my HTC HD2 from WM6.5 to WP7 and upgraded via Zune to 7.10.7712.60:
I installed ROM " Back to the Future [XBmod-Yuki]" by following the guide http://forum.xda-developers.com/showpost.php?p=17205291
and stopped at the step 14 (I didn't want to update to 7720 with manually pushing cab-files (HD2-7720fix.rar) to be alble to update OS via Zune later when official release is published).
Also I deployed DEV_UNLOCK.cab (http://forum.xda-developers.com/showthread.php?t=1250869) and installed some apps through W.I.N.C.O.'s AppStore v.1.0.5 (http://forum.xda-developers.com/showthread.php?t=1245206).
I haven't activated any Windows Live ID yet.
Today Zune found Mango update (7720) and I've tried to apply it.
At the step 5. I'm receiving the error with the code 800B010A
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I've tried the update many times with the following actions:
- restart the device
- restart my PC
- restart Zune
- set SIM pin code, restart the device, clear SIM security
- reset my WP7 (Settings => About => reset your phone) without SD card
Each time I received the same error code.
At the moment no success. The phone works fine now but with OS version 7.10.7712.60.
Can anyone give me a clue how to apply the update?
MFliorko said:
Today Zune found Mango update (7720) and I've tried to apply it.
At the step 5. I'm receiving the error with the code 800B010A
I've tried the update many times with the following actions:
- restart the device
- restart my PC
- restart Zune
- set SIM pin code, restart the device, clear SIM security
- reset my WP7 (Settings => About => reset your phone) without SD card
Each time I received the same error code.
At the moment no success. The phone works fine now but with OS version 7.10.7712.60.
Can anyone give me a clue how to apply the update?
Click to expand...
Click to collapse
I get that error to
Update: connected to my zune account (on zune) and update success
nelsonberenguer wrote:
Update: connected to my zune account (on zune) and update success
Click to expand...
Click to collapse
Zune accounts and Microsoft Marketplace are not supported in my country.
Therefore I applied DEV_UNLOCK.cab to unlock the device for development.
MFliorko said:
nelsonberenguer wrote:
Zune accounts and Microsoft Marketplace are not supported in my country.
Therefore I applied DEV_UNLOCK.cab to unlock the device for development.
Click to expand...
Click to collapse
In my country neither
You only have to change your location to United States and zune marketplace will work.
Had the same error on my laptop (Win 7 x64).
Tried everything (restart computer, reboot phone, Zune sign in, force update trick) but no success.
I eventually decided to try again but on my PC (Win 7 x32) and BINGO, it worked !
Just for those who might ask:
- all settings, live tiles, installed apps, etc. were not touched;
- marketplace download works;
- app deployment works;
- obviously, multitouch and camera issues remain (HD2 drivers related);
- too soon to say anything about battery drain.
To end this, the update seems pretty safe to me but do it at your own risk.
make sure lock screen is off worked for me
One shot mango
nelsonberenguer said:
You only have to change your location to United States and zune marketplace will work.
Click to expand...
Click to collapse
Where did you change location?
- when you were registering Zune account (than you should enter some US address, but M$ check users' locations)?
- in Zune?
- in WP7?
My WP7 has US regional settings.
MFliorko said:
Where did you change location?
- when you were registering Zune account (than you should enter some US address, but M$ check users' locations)?
- in Zune?
- in WP7?
My WP7 has US regional settings.
Click to expand...
Click to collapse
you have to change in windows (pc) .
go to control panel and in regional settings change location to US
nelsonberenguer said:
you have to change in windows (pc) .
go to control panel and in regional settings change location to US
Click to expand...
Click to collapse
You also may have to settings/about reset your phone. On reboot the first screen shows location choice.
Edit; sorry this shows language choice, but may be relevant.
nelsonberenguer said:
you have to change in windows (pc) .
go to control panel and in regional settings change location to US
Click to expand...
Click to collapse
I've changed regional settings on my Windows 7 x64 and rebooted it.
Also I've found that my WP7 had showed wrong date (09/21/2011). I've changed and rebooted it too.
But still has the same error when I'm trying to apply the Mango upgrade.
The only thing I've haven't tried yet is reset (hard reset or Setting => About => reset your phone). But I'll lose all my settings, contacts, photos, installed apps etc.
Any other idea?
For me it stucked on restarting, you just have to be very patient at this stage because it takes alot of time
Solved!
I've tried, I think, everything. Nothing helped me.
Finally I manually upgraded from 7712 to 7720 (from cab files "HD2-7720fix.rar"). Zune found the update (cleanup) but during the upgrade process I caught the same error 800B010A.
Then I found the following advice (http://forum.xda-developers.com/showpost.php?p=17950050&postcount=3431):
-take out SIM card (remove it from the phone device)
-increase reserved memory. In Zune (desktop) go to Settings => Phone => Reserved Space => change reserved space from 5% to 10%.
And the upgrade in Zune is successful!
I home this can help someone.
I don't know whether it matters...
Before manual upgrade with cab files from 7712 to 7720 I removed developer unlock (applied DEV_UNLOCK_REMOVE.cab). After that the upgrade process in Zune continued being failed (of course).
Eventually after I successfully applied official upgrade (see my previous post) I unlocked the phone for development (with DEV_UNLOCK.cab).
I've just installed a few apps to my WP7 Mango (7720 official).
Everything is the latest and works fine now!
So does anyone know if the camera issue has been fixed in this final update? Or is it still a driver issue as previously stated?
VPN solved my Problem.
I live in Iran and tried every option you guys mention it but it didn't worked.
But When i Used a encrypted Europe VPN it worked.
and about "zone account login issue" if you change your your country in regional and language setting in control panel you can access the market place in zune.
Error 800B010A - You can try this
Heya,
I tried to update our beloved HD2 today...well I got the dammit 800B010A error all the time (approx. 15 times). I tried the USB update thingy but no success.
If there are still people out there who are struggling with the error:
After checking for USB drivers you can try to:
1. Take out your SIM card!
2. Increase the "reserved space/storage"! (I'm on german zune, so I don`t know the correct wording). You find this when you are in Zune (on Desktop PC) under Device - Settings.
At least the update directly worked for me after increasing the space from 5% to 15%.
Take care.
Ric
Wifi problem
I've succsessfully updated my HD2 to the offical Mango release via Zune, but I got Wifi problems. When I go to settings - wifi and click it won't open. It just says that wifi is turned on... Anyone know a solution to this? It is so frustrating and it drains my battery. Any help appriciated Thank you!
mrventura said:
I've succsessfully updated my HD2 to the offical Mango release via Zune, but I got Wifi problems. When I go to settings - wifi and click it won't open. It just says that wifi is turned on... Anyone know a solution to this? It is so frustrating and it drains my battery. Any help appriciated Thank you!
Click to expand...
Click to collapse
Try switch phone off and on.
Else try wifi rom fix cab eu or us http://forum.xda-developers.com/showthread.php?t=1250869
Robbie P said:
Try switch phone off and on.
Else try wifi rom fix cab eu or us http://forum.xda-developers.com/showthread.php?t=1250869
Click to expand...
Click to collapse
Unfortunatly none of the above worked :/ Think I'll have to hard reset
Official Mango ?
What does do ISV cleanup ?
What diference is between the developer mango and official after ISV cleanup ?
Is ISV cleanup everything what we have to do to have official 7720.68 build ?
How I will know that I have unlocked phone, that I can upload app via developers tools ?
Hi Guys
Can someone tell me how to reinstall windows mobile on hp hw6915?
I realy need your help. In this 'xda-developers' i not find any info about this, so i decided create this post for hp hw6915. Can anyone help me?
ExodiaXlr7 said:
Hi Guys
Can someone tell me how to reinstall windows mobile on hp hw6915?
I realy need your help. In this 'xda-developers' i not find any info about this, so i decided create this post for hp hw6915. Can anyone help me?
Click to expand...
Click to collapse
just follow the tutorial on this thread ~ http://forum.xda-developers.com/showpost.php?p=6391896&postcount=1
If you just want reset to default factory settings, you must press all together: power + green button + red button + reset with stylus (bothom of the phone).
If you want to change language of hw6915 you must reflash with ROM update utility, but make sure there are no rom update files for radio (RadioOS.nbf RadioFS.nbf) as they could brick GSM part of the phone.
Thank you for this link about how to reinstall os, but still i dont understand anythink in this tutorial about os. Can someone make a video turotial?
If you are following that tutorial be aware! Do not "task 28 55aa" with mtty - that will cause change of the device Product ID and you will not be able to use official HP upgrade tools anymore.
Why it is that you want to reinstall rom? Does hard reset not working?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I try to do hard reset, but stil i have same problems with this hp hw6915. Problems is: i cant remove some programs, windows is flickering lines. memory to low, i try increase memory by removing some programs but it does not work and t.t.
It is true that default software on hw6915 is slow - you should use memorycard for software to get better results.
If you are really willing to try to reinstall, I can only give you this one link
multiupload com /UTYDNBZ145
Click to expand...
Click to collapse
but use it at your own risk - it is possible that results will be the same.
What you think about this?
How to write custom rom WM on hp iPAQ hw6915.
------------------------------------------------
1.Connect your device to PC by ActiveSync (download it from microsoft page)
2.Run "Command prompt" from folder "SPL vG.39" (if using vista/7 RUN AS ADMINISTRATOR)
3.Enter this command: pdocwrite spl -n0 -b 0x20000 0 0x80000 (WAIT UNTIL IT FINISHES).
This command replaces a file in the ROM which allows you to flash ''non-original roms'',
basically software CID unlocking which allows flashing of ''cooked roms''
4.You will get a warning on your hp regarding a dll file (itsutils.dll), PRESS YES
5.Put your device in bootloader mode. (hold the two selection buttons next to the joystick
and shortly tap the reset button with your stylus)
6.Open activesync, go to connections and untick "Allow USB connections"
7.Extract "Sable_G4_1.21_UK_ROM.rar" and run "Sable_RUU.exe"
8.Press on the big "Upgrade" button
9.There will be a progress bar, when it's done it should say something like "Update finished !!"
10.Go back to activesync and re-tick "Allow USB connections".
The manual you quoted is correct for case if you want to upgrade to non-stock rom like some custom made Windows Mobile 6 rom (if you already found one), but you must ensure that there are no RadioOS.nbf and RadioFS.nbf in the folder where Sable_RUU.exe resides or else you might ruin your gsm.
If you just want to reinstall Windows Mobile 5 then there is no need for "pdocwrite spl -n0 -b 0x20000 0 0x80000" (as it is only needed to allow non-stock rom flashing).
So in order to do wm5 reinstall i just must follow my writen instruction but in this case i need skip 2, 3 and 4 steps, and start from 5 step? (of course first i need plug my device to PC by ActiveSync). ?
What is Radio?
In Sable_RUU.exe i found such files: CEOS.nbf, EnterBL, GetDeviceData and Sable_RUU.
In SPL vG.39 folder i found such files: Command Prompt, itsutils.dll, libeay32.dll, msvcr71.dll, pdocwrite und spl.
Can someone help me!
I was doing this update tranquility, I have a hp ipaq 6915 and use the windows7.
I did the first part of this
process, which installs the. dll. All right so far. I was
for the second stage and the program Sable RUU erased my
WM5, ok, so that after this process began to windows
search for the driver usb ipaq, of course, was
disconnected, then this error appeared Client_GetOSVer fail !! Error : 501.
Now I'm without my operating system.
And what I do now?
From what I undestood from your one before last post (the files included gave me idea) you have downloaded wm6 update utilities and rom. So in this case you must take all the steps.
If you want wm5 then you must download link http://multiupload.com/UTYDNBZ145 and just plug device to usb (before that put it in the bootloader mode: by pressing power button + button next to green + button next to red + reset with stylus), wait to connect and then run Sable_RUU.exe
About your question... Radio rom files are sometimes included in distributed upgrade files, so you must ensure they are deleted from the folder before start flashing. These files are usually responsible - there already been two cases to my devices - for killing the GSM chip data, so you can not use your device for phone calls anymore lets sey it is very bad scenario, so I am warning you to not to break your device!
Seems like you are left without any os at this very moment, so you should now install wm5 again and if you then want to upgrade wm6 repeat all the steps (including pdocwrite command).
If you are just stuck in bootloader google for UNI_ExitBootloader.exe
So bootloader mode is when my hp hw6915 screen show this: Serial Hp G.39 or when hp hw6915 screen is totaly off? When i try use UNI_ExitBootloader.exe it does not work because it say: Error - Cannot open USB port. So i try again and again but this time i disable ActiveSync... but still in not work. So i try an alternative method. I download Virtual box, then i install win xp, download Sable_G3_DEVICE_ONLY_hw6915-1.21uk ant try run. IT WORKS
THNAKS YOU JOGIJS ;-) Now i need your help to update my device from wm5 to wm6 o greater.
First of all - there are no official hp releases upgrade to wm6 or greater, but as I think you found one of unofficial upgrades to wm6 made by hackers.
Then - Sable_G3_DEVICE_ONLY_hw6915-1.21uk is the same as in my link http://multiupload.com/UTYDNBZ145 only difference that my file is without the radio roms.
About upgrading to wm6:
As I said before - now you need to follow instructions you posted before and do all the steps to upgrade to wm6 (remember about my radio warning! ) as you have found correct manual for wm6 upgrading.
If you understand russian you could try this wm6 upgrade - http://www.multiupload.com/QTP68IW7AM
About your question:
You are in bootloader mode when there are serial/USB + hp logo + G.39 on the screen.
If you have USB connectivity problems on w7 32bit, use this driver - http://www.multiupload.com/IE15IM9DHT Always check your device manager to ensure your Sable device is recognized!
One more question ;-) In my Hp Hw6915 i install wm for G3 chip, but i noticed that mine is G4 chip. So in future this can cause problems on mine device?
I think it is just a mislabel as mine current device is also G4 (as seen on hp's asset viewer) and it does not run into any problems by flashing OS
Maybe confusion is set by bootloader's title "G.39"... I think so, but I am not sure, what caused this for true.
Despite all - these roms and utilities worked for me (except for radio roms of course).
same problem
hello i have hp ipaq hw6915 in norvegian language i try to use your tutorial and now appear bootscreen (USB+Logo+vG.39) how can i do for resolve my problem because i try to HARD RESET and appear same USB+Logo+vG.39, you can reupload your application to other website?
under the boot screen it's .39. it's fine.
what do you want to do with your ipaq? still using wm 5 or wm 6?
I can give you a link on xda which has all the explanation on how to upgrade to wm 6 but if you want to stay on wm5, I suggest you do a hard reset. if you say after hard reset you still cannot remove program, I am quite confused. Because hard reset really put you in a basic start where everything is cleared.
try hard reset one more time...
if you still have problem, post again here... I will try to help you as much as I can...
i try HARD RESET 1000 times appear same USB(or SERIAL if is not connect on pc)+Logo+vG.39, i want to try WM6, if you can help me pls offer a solution.
download this file, unpack and run Sable_RUU
http://www.4shared.com/rar/NokqR8Q2/121_UK.html
worked fine for my hp 6915 with Danish rom - I have English now
IT MIGHT HELP YOU