Hi guys
I've trawled through the forum and not seen a post with my problem
I got my X10 yesterday, got it home, left it on charge for around 5/6 hours. Gave me full battery. Used the phone all day yesterday, however when put on charge it wouldn't charge? I read somewhere that first time charge it may have to drop to 5% before would charge. So left the phone on for it to fully drain.
It turned itself off yesterday at about 4pm GMT - Plugged it into AC charger, sony erricson screen loads up, then it just says power down and turns itself off.
It has been plugged in usb on 2 different PC's, I've tried using different sockets around the house, I've taken battery out, checked terminals they are clean.
When plugged in the red led just flashes every few seconds and if I unplug the charger and goto turn on it just flashes 3 times.
It has been on 'charge' for over 14 hours now and still it loads up then powers down, occasionally it will flash up saying 2% battery left please connect charger.... (I've had it on charge over 14 hours..)
Could this be a dodgy battery? It worked fine yesterday from the intial charge when I recieved it.
Thanks
Stu
Seems to just be in a constant loop
I am going to ring carphonewarehouse at 11 when they open, but I'm guessing they'll just ask me to send the phone back...
sounds like cable or the wall charger itself or even the battery. best is to take it where you bought it and have them test what is the issue is.
Yeah, going to ring at 11 when the shop opens. Hopefully they can switch me a battery and charger in shop and we'll go from there. Just strange how it worked the previous night!
h d a simulare problem. it turnd put the my micro usb cabel w s not in proper place. the cover of the usb slot. made that the plug would. ot go in completly. nd tye phone said it charge. so make shure that tye cover is net betwen the hole and the plug: -)
Sent from my X10i using the XDA mobile application powered by Tapatalk
howd you get on stuball? did you try all the usual stuff. taking battery out, sim card, out, SD card out.. clean the contacts.. reinsert etc..??
umm... English? ill assume you mean the cable plug cover on the phone was stopping the connector on the cable from going right in cause it wasn't folded out the way right?
h d a simulare problem. it turnd put the my micro usb cabel w s not in proper place. the cover of the usb slot. made that the plug would. ot go in completly. nd tye phone said it charge. so make shure that tye cover is net betwen the hole and the plug: -)
Sent from my X10i using the XDA mobile application powered by Tapatalk
Click to expand...
Click to collapse
Sent from my X10i using the XDA mobile application powered by Tapatalk
stuball21 said:
Hi guys
I've trawled through the forum and not seen a post with my problem
I got my X10 yesterday, got it home, left it on charge for around 5/6 hours. Gave me full battery. Used the phone all day yesterday, however when put on charge it wouldn't charge? I read somewhere that first time charge it may have to drop to 5% before would charge. So left the phone on for it to fully drain.
It turned itself off yesterday at about 4pm GMT - Plugged it into AC charger, sony erricson screen loads up, then it just says power down and turns itself off.
It has been plugged in usb on 2 different PC's, I've tried using different sockets around the house, I've taken battery out, checked terminals they are clean.
When plugged in the red led just flashes every few seconds and if I unplug the charger and goto turn on it just flashes 3 times.
It has been on 'charge' for over 14 hours now and still it loads up then powers down, occasionally it will flash up saying 2% battery left please connect charger.... (I've had it on charge over 14 hours..)
Could this be a dodgy battery? It worked fine yesterday from the intial charge when I recieved it.
Thanks
Stu
Click to expand...
Click to collapse
the x10 uses way more power during switch on and charging and this power cannot be suplied by the usb port.
use a wall charger instead...
Charger
When battery is drained, it can take a while for led to light up (giving impression of not charging). You may find that leaving it plugged in for 10 mins will resolve your concerns, the led will light up showing charge state.
External charger? Will it work?
the manual says that it can take up to 30 mins for the phone to even recognize charging. so if you see he red light flashing, its nothing to be concerned about.
i to have had the same problem, not charging and shutting itself down. i had mine 8 days and it was the first day i had used it, took it back t-mobile for repair and they sent it back to SE, 2 weeks later i had a report on what was wrong with it,
Apparently i dropped it or crushed it, just from picking it up and plugging to be charged, so now SE wont repair it. doesnt matter how much i argued with t-mobile that i did not drop it and they will always take the word of the engineer. so i am without a phone and still paying a £35 month contract, and in the long process of contacting t-mobile head office with the supply of goods and services act 1982, all i want them is to repair the damm phone. any one else got any more suggestions
Had similar problem downloaded USB drives and had to do a hard reset on phone. Worked fine after go to Sony Ericsson web check for support and downloads for x10.
I had the exact same problem. Phone would not take a charge and wasn't being recognized by my comp. I tried my battery from my X1 and it worked, and tried charging the battery via my X1 and battery was charging so it was obviously a problem with the charge port. I looked into getting it repaired via warranty but the Sony rep quoted me an unacceptable amount of time. I was able to get it repaired locally same day for $45. Works perfectly now.
Just to clarify for future readers, there may be two issues: (1) software, which per @RMD357, requires downloading the drivers again and doing a hard reset, and (2) hardware, which per @dunny, requires repairing the charge port.
Question to @RMD357, where did you find the drivers to download? I searched the SE website and could not find drivers.
Question to @dunny, what do you tell the repair person if you suspect that the charge port is an issue.
Thanks.
@visitador02 I just told the person at the repair shop my phone stopped taking a charge/being recognized on pc and that I tested different batteries, chargers, and cords so it was most likely a charge port issue. The guy at the shop told me that the charge port was probably damaged while connected to the USB cable and just replacing the part solved the issue. I believe the part cost like $10.
Related
Hi,
My wizard run out of battery completly yesterday, I brought it home and try to recharge it, but no recharging light will appear.
I left it overnight connected to the mains but to no appeal,
I also removed the battery for a few minutes and then plug again but no luck.
I´m not using the mains provided adaptor but my travelling kit, a proporta mains/usb adaptor and a retractable sync/charge cable with a mini-usb pin cos I´m back home for Xmas and I don´t travel with the mains.
I have read about problems with some chargers from Boxwave, but I have consistently using this charging conbination since October.
Any ideas, should I send it back to expansys to repair, or is there anything else I can try?
Thanks
Elsral
same thing happened to me.. Supposely the phone will not charge from being completely dead without a charger that puts out 1amp. There is another method if you are a little brave... cut up an old car charger and hook it directly to the battery (red cord to + on battery and black to -) Read about it on howardforums and it worked like a champ. I only needed to jump the battery for about 30 seconds before I put it back in the phone and the amber light kicked on.. I was very relieved!!
Same happend to me yesterday. Simply plug the carger in and wait 1 or 2 seconds then switch the power button. After some seconds the carging light should switch on.
The wizard won't charge if it's switched off.
Export800,
you are a megastar,
I put apart a usb adaptor that I had built to charge my gps and I connected cables directly to battery for a minute and Voile,
tnx a million,
elsral
Xunil99 said:
Same happend to me yesterday. Simply plug the carger in and wait 1 or 2 seconds then switch the power button. After some seconds the carging light should switch on.
The wizard won't charge if it's switched off.
Click to expand...
Click to collapse
But if the battery is totally dead surely the unit wont switch on ? Thus its a catch 22 ??? There is no power to switch on and the battery wont charge totally dead.
Ridiculous if you were caught out away from a charger and ended up having to pull apart a usb lead to get things back to life.
If the battery is so low, that the wizard switches off itself, and you connect the charger, it won't charge, because it's switched off.
Use the power of the charger to turn it on, then charging will beginn (and also the device will boot).
Xunil99 said:
If the battery is so low, that the wizard switches off itself, and you connect the charger, it won't charge, because it's switched off.
Use the power of the charger to turn it on, then charging will beginn (and also the device will boot).
Click to expand...
Click to collapse
Can anyone else confirm this works as there have been many people having this problem. Simple solution if it works.
Switch off your device completely (hold the Power Button) and try to charge: Nothing happens. Now switch it on - charging begins.
I have noticed that last week, when battery was very low and i know that i would need my wizard in about half an hour. So i switched it off completely, so that it would charge faster and noticed that.
Yesterday when battery was totally dead i remembered that and i switched it on.
Btw, doesn't it damage the battery, if you connect it to 12 V (!!)??
Xunil99 said:
Switch off your device completely (hold the Power Button) and try to charge: Nothing happens. Now switch it on - charging begins.
I have noticed that last week, when battery was very low and i know that i would need my wizard in about half an hour. So i switched it off completely, so that it would charge faster and noticed that.
Yesterday when battery was totally dead i remembered that and i switched it on.
Btw, doesn't it damage the battery, if you connect it to 12 V (!!)??
Click to expand...
Click to collapse
If I come across the problem will certainly be trying your method before I will be ripping into any usb leads
The same thing happened to me this past weekend. We were out camping and my MDA's (wizard) battery went completely dead. I had a USB sync cable for my laptop, but that would not revive the unit. I'm afraid the only way to bring it back to life is with the original OEM charger which has an output of 1 amp. Thanks for the post!
I had the same issue a while back. At first I thought the moto charger I had was dead but then I plugged in a old SMT5600 and it worked fine.
I left it plugged into my computer for a hour or so and finally I heard the "new usb device blip" from the other room and it started to charge. Guess I was lucky.
Same thing happened with my wifes SMT5600. The battery died and she couldn't get it to charge with her moto mini usb charger. I plugged it into my machine and a hour later the charging light came on.
I have heard that the Wizard will not charge from my laptop using a usb cable if it is completely drain. I find this to be NOT TRUE.
I ran out of juice twice last weekend. The thing about the Wizard is that, if it's completely drained, it will get stuck at the boot screen, and go no further.
Take out the battery to turn it off again. Put the battery back in, and then plug in your charger. DO NOT TURN IT BACK ON. It needs all the power it can get. Give it a minute, and you will see your orange charge light come on. Just leave it alone for several hours, and it will charge. This is my experience.
I got it! But, first the story.
None of the above methods helped me. I tried plugging it in to a big truck lighter, a pickup truck, even an ac adapter for my coleman cooler. Nothing!
However, I had a powered Pro-Clip mount that I had as a backup for the one I use. Guess what? THAT worked!
I think the cable makes the difference. Need to find the specs on those puppies. LOL
Thanks for the help.
Hi - my first post.
I have a charging problem not unlike that posted by Jurgensen on 25.11.08.
My X1 will no longer charge from a USB charger when it is turned on. It will only charge from a wall socket charger when turned off. Neither will it charge from a car socket or additional battery (Proporta type).
But, when I charge from a PC - whether it is synched to the X1 or not - the phone charges when it is turned on.
I have had had my X1 for a couple of months and this has only just started happening.
I admit that I have used different chargers and leads, apart from the SE supplied one, perhaps I have caused some damage doing this. I have tried using 4 different USB chargers and various different leads, but no go.
One coincidence is that it started happening the day I loaded VistaHide battery gauge - which seems very good. I have tried deleteing that file, but it does not make any difference.
I have just installed the latest UK O2 firmware, but no change.
Any help and suggestions gratefully received.
John.
In settings>system>power is the "when device is turned on, do not charge the battery when connecting to the pc" box unchecked? Just a thought...
As you have flashed the phone its unlikely to be a software or settings problem. And different mains and car adapters dont work its most likely to be a fault with the phone.
Phone O2 and ask for repair/replacement?
same problem as mine!
i told them just back my freaking phone! so i got it back UNREPAIRED!
I did not buy a 800$ phone so i can use it 1 month, 2 month, or 1 year later!
http://forum.xda-developers.com/showthread.php?t=474546
charge problem
i have the same charging problem. I must turn off the phone to charge from the car OR wall charger. It does charge from the USB PC connection.
When I plug it in to the wall, the display DOES get brighter. But the illumination lights don't go on nor the battery charging icon. If I turn off the phone, the illumination lights DO work when hooked up to charger.
Did anyone find out what the problem is?
I did find something that suggested maybe the battery isn't tight, but I tried several time to reseat the battery. This all started sometime after I had to take out the battery because the phone froze.
I have done a hard reset AND even did a software update getting the new software but the problem is still there.
it' a hardware problems.
and Sony Ericsson is a SCUM, after they got your money, they dont give a ****!
i sent my phone in for repair, they gave me the same BS excuess everytime, "we waiting on parts, and we have no idea when parts available".
u the manufacturer and u have "no ideas when parts available"??
ok, htc made the phone, how hard is it to give them a call and ask them??
Hi all,
My TD1 would charge from any mini-usb charger (such as the one I have with my TomTom). I put the TD2 on charge from one of these last night. The front light went orange, and the battery status changed to charging. However, I wake up this morning (7 hours later) and the light is still orange. I disconnect and look at the battery info and it says the last charge was yesterday.
Is the TD2 fussy about which charger you use? I really hope HTC are not pulling an Apple and locking their devices to only their accessories!
R
rakh1 said:
Hi all,
My TD1 would charge from any mini-usb charger (such as the one I have with my TomTom). I put the TD2 on charge from one of these last night. The front light went orange, and the battery status changed to charging. However, I wake up this morning (7 hours later) and the light is still orange. I disconnect and look at the battery info and it says the last charge was yesterday.
Is the TD2 fussy about which charger you use? I really hope HTC are not pulling an Apple and locking their devices to only their accessories!
R
Click to expand...
Click to collapse
I think I remember reading something about an option for not charging the battery when connected on PC USB (presumably for saving laptop batteries ;-) ) in the manual.
So I guess that the TD2 has a way to detect if it is plugged into a charger or a laptop, and maybe it can do that only with HTC charger, believing your charger is in fact a laptop. I would have guessed they use the activesync status to differentiate between PC and charger, but maybe not ;-)
So what could maybe solve your problem is to select "charging battery if plugged to a computer", I think it is in the touchflow 3D options somewhere... I would play with those options to check if it improve things...
Settings - All Settings - Batter - (Battery Tab). "When device is turned on, do not chagre the battery when connected to the PC.".
For me this is unticked - and when it was plugged in the battery reported as 'charging'.
Strange!
R
rakh1 said:
Settings - All Settings - Batter - (Battery Tab). "When device is turned on, do not chagre the battery when connected to the PC.".
For me this is unticked - and when it was plugged in the battery reported as 'charging'.
Strange!
R
Click to expand...
Click to collapse
Does it work with the standard HTC charger?
And plugging to a PC?
If yes, your other charger may be a little light in specs (amperage too small, or voltage slightly below USB specs) and the TD2 may be picky regarding this...
I would also inspect the microusb plug of the charger to check for dirt/corrosion/deformation, and also the battery within the device: I already had intermittent problems like that caused by imperfect connections: the device was in a charging state, but no actual charging did occur. Replugging carefully after blowing on the plugs solved the problem....
From past experiences, all my HTC phones charges up with any USB cables or chargers, even my HD. So may your battery is not working some how... best thing to do is try charging it with your original charger or connect your device to your computer, it should charge up. If not, then take it back to your dealer man! I don't want to say it but maybe you have a lemon...
Hi all,
It charges well from the supplied wall charger. It also appears to be charging well from the computer. So, this leaves me to suspect the other (non HTC) charger.
Thanks for your help....
R
OK - this just getds weirder and weirder...
Yesterday, plugged into PC all day whilst I was working. After a while green light so fully charged. Went out for an hour or two and when I came back I put it on a different wall charger for a test (my old TD1 one) and after 30 mins or so green light - so fully charged again.
So, I thought - this is great, it proves the other wall charger has a problem. Before bed a few hours later I took the TD1 charger and put it in the bedroom. Plugged the TD2 into it overnight. Woke up this morning, and orange light???!!!
Put it into the computer this morning and after 15 mins - green light???
CONFUSED!!!
Could it be some function whereby it won't charge a bettery that has been charged full in the past x hours or so??? Is anyone else seeing anything like this????
R
I think you have might have a duffed battery. I think you should really check it out.
I use a Motorola universal mini-usb charger i mine car and I haven't noticed any different behavior than using the supplied HTC charger or HTC usb cable in my laptop..
I put it on the supplied charger for 12 hours and it did not charge at all despite the orange light being on. As I am within 7 days I've asked DeviceWire to refund or replace...
R
Way to go, you should get a new one!
check the connection!
rakh1 said:
I put it on the supplied charger for 12 hours and it did not charge at all despite the orange light being on. As I am within 7 days I've asked DeviceWire to refund or replace...
R
Click to expand...
Click to collapse
First of all, yes you are.. IF the device is faulty!
from experience, I know that some cables dont charge the device.. First of all make sure there isnt some dust or stuff in the connection. secondly, try resetting the device.. If the orange light is on, then it only means some of the pins in the EXTusb connection have been shorted, my reccomendation, check the pins on the miniUSB connector on the phone, and make sure you didn't bend some.
Hey all,
No bent pins.
No dust or dirt in the socket/plug.
Tried 3 (HTC) wall chargers - all the same behaviour.
Tried resetting the device.
No luck
R
I especially used my USB-Charger this night to charge the device.
It is a Hama USB Charger (Prod# 00014095, you can find it with this on google).
It has an output of 800 mA, while the original hast 1000 mA.
But it charged up to 100% and was "green" this morning.
So it seems to work and is really Small in size
Regards Thorsten
Well, this has been a problem for me from the start and all I have used are HTC chargers. I've not had anything like this sort of issue with the previous HTC phones I've owned (and there have been a few - check sig). What confused me was that it does appear to accept charge from the USB port of a computer - which is just odd??!?!??
Anyway, I think this is unacceptable from a new product so I've asked for a refund/replacement. Awaiting a reply from Devicewire.
R
Whats weird,
My TyTn has some probs in this department.
From time to time, setting it on USB power, will not even lit the charge-light.
And it will not charge.
I have to reset it and then it works.
Dont know what that is.
DeviceWire sent me an RMA. In the meantime I hard reset the device again after confirming that the wall charger would not go above 89% charge - 9 out of 10 bars (I installed a prog to give me a % reading).
After hard reset the battery went from 89% to 100%. I am now running it down again - before I give it one last chance overnight. If I wake up tomorrow and it is still orange and at 9 of 10 bars then off it goes...
R
Fingers are crossed for you mate! Hope it goes well.
This just gets stranger - after *this* hard reset it now appears to be working as expected - woke up this morning to a green light for the first time!!
So, was this just a software thing - solved by a couple of hard resets - or might there still be a problem lurking underneath???
Problem now is that if I send it back to DW they'll confirm it is working as expected. If I wait and do not send it I run out of the 'return within 7 days for a refund' and will have to reply on HTC aftercare (horror!!).
What to do!!!???
R
I'd still return it but in your RMA notice stipulate that you suspect the problem "seems" fixed but say it might come back again and on that note are still returning it for a replacement/refund.
Damn it..... i dont know what happened
it is still working perfectly yesterday
i did not drop the phone or battery, today the battery is still at 40% and as usual, before i went to sleep, i plug my phone on the USB Cable connected to my computer... but it is not charging.. and here i thought the error comes from my USB Cable , so i plug it into my wall charger ... but it is not charging at all!!!
and i thought, perhaps i have installed something , or some os faulty issue ... so i reset the phone via SETTINGS > About > Reset Phone
and after the reset.. it is still not charging...
argh what should i do... please help... anyone
i purchased this phone from singapore.. and i am indonesian.... the battery is currently at 30% , i am so afraid after it runs out of its juice, it will go away forever (because i cant charge it) T.T
what should i do....
(Is this battery and the one used on Galaxy S is the same? My sister has Galaxy S, should i try using her battery and try to charge it from my phone? .... ARGHHHH the omnia 7 is not even available yet in indonesia) T.T
Anyone help T.T
Get another charger it will charge get a new 1
Sent from my Nexus One using XDA App
you sure it is the charger?
You are talking about the wallcharger right?
usually it already charging via USB Connected to a computer.. but this time... the computer does not even detect if anything is connected.... (nothing happened when i plug this phone to my pc, usually there is a notification sound playing and my zune will autorun)...
damn it ... why this happened.. yesterday it is just fine (
damn it .. i am sleepy already..
i will go and sleep for now.. and left my phone turned off and plugged in the WallCharger
and hopefuly.... sigh.. it is still charing although no indication whatsoever is showing that
MAN... should i just try bang the damn battery hard onto the table... perhaps some of the chip inside the battery is misplaced by whatever unknown forced?!
damn it.. i never dropped the phone.... ARGHHHHHHHHHHHHH
this is so frustrating
Relax
Relax man your charger is bad.
I have the same problem but my girlfriend have a Wave and start using his charger and everything works fine.
Buy a new charger
question
can i use any charger from any phone for this Omnia 7?
(the one that has USB Output of course, such as xperia1 charger)
if we can, then it is also not working.... and why suddenly it wont do anything when i plugged it in my Computer USB
the very same computer works perfectly yesterday, and suddenly it is not working..
I suspect either one of these is the problem :
1. the micro USB Connector in the Phone is broken somehow , hence the when we plugged it on, it does nothing
2. the Battery (which if i am not mistaken has a chip inside) is broken, hence explain why it is not charging at all (which a bit does not make any sense, if it is just not charging at least when i plug it on the computer, it should still detect this device...)
I am from indonesia, i can ask my friend who is returning from melbourne to purchase a new battery and new charger hopefuly
Okay to make things simpler.. i have a sister who own a Galaxy S
can i use the galaxy s wallcharger to charge my omnia 7? ah hell,i will try it anyway...
okay according to this
http://www.samsung.com/us/mobile/cell-phones/SGH-I917ZKAATT
it goes great with galaxy s standard battery...
so i suspect, i can use my sister galaxy s standard battery and try to charge it using my cellphone
and i can also try to use my sister galaxy s wallcharger to charge my battery...
okay lets try ... hopefuly.... it is only the battery.. i can easily purchase a new battery... if it is the USB Connector on the phone... damn, how on this green earth can i charge my battery? OH we can use the kickstand battery charger?
hmm suddenly it is working now :O
thanks God... hopefuly it will never ever happened again T.T
Great it is working again
Any possibility that there is a way that the device forces a full recharge cycle to calibrate the battery?
Honestly i guess so.
I have the same problem...i can t charge my i8700 at all...what did you do to charge again???...i use a universal charger where i put my battery ...this happens for two weeks now..
cody28 said:
I have the same problem...i can t charge my i8700 at all...what did you do to charge again???...i use a universal charger where i put my battery ...this happens for two weeks now..
Click to expand...
Click to collapse
Try allowing the phone to run out of battery and turns off, then plug it into the charger, i would love to know if this is a failure or be design behavior.
Put the battery in the phone,
Wait untill the phone goes completely off.
Plug the phone to the wall charger.
write back here
i tryed this but the same problem it turns on but only while the charger is pluged in when i pull it out the phone turns off...i try to hard reset nothing..there is no update to work with non retail devices...the phone is from three uk...i m from romania there is no way to return there to an service..(
Having the same problem. Been working flawlessly.Plugged it in a couple of hours ago,but it doesnt appear to be charging.
When I use the USB charger on the PC, it is recognised, and Zune opens up fine and Phone shows up.
Have tried two Mains chargers, the Omnia 7 one and the one that came with my Galaxy S, same problem.
EDIT:
Left it plugged in overnight and it charged fine.Used phone, going down to about half battery.Plugged it in and seems to be charging without a problem!
I've got the same problem as you guys for a couple of days now.
Thanks for your reactions i will try everyone of them untill my omnia 7 charges again
knetsooj said:
I've got the same problem as you guys for a couple of days now.
Thanks for your reactions i will try everyone of them untill my omnia 7 charges again
Click to expand...
Click to collapse
Do you have a bit of battery left?
Windows Phone 7 devices power up when you plug them in. Maybe the OS is not booting and because it is S-AMOLED display we cannot tell if it is on or not.
Try Hard Resetting without booting WP7
http://forum.xda-developers.com/wiki/index.php?title=Samsung_Omnia_7
Make sure you have a bit of power though, you don't want that to stop in the middle of the proccess
This has happened to me a couple of times. I think it's just a reporting bug, the battery is actually charging. I just have to restart the phone and it magically has charge
battery is charging too long
How long does take to fully charge the battery? For me it's about 4-5 hours with wall charger. Should not it be faster?
Mine is about the same for a full charge and I have also noticed my Omnia 7 not charging properly when I plug it into my MacBook Air however it does seem to charge fine on my Dell laptop for work.
Maybe the Omnia 7 is very sensitive for charging over USB on a laptop and needs a certain voltage for it to charge properly?
What works for me:
1. Original charger
2. iPhone 4 charger
3. iPhone 3GS charger
4. Blackberry Curve charger
Not tried any other micro-usb cables yet but will do at some point in the future.
I had the same problem too. The battery was suspiciously showing high levels for the last three days (went without a charge!). In the morning, the alarm did not go off, and I realised the battery was dead dead! Charged (wall charger) for 1.5 h without any use -- would turn off if I unplugged. Tried with the USB cable too (connecting to computer) and no use.
I read this post, and tried with the wall charger again, and it shows me ~60% battery, and seems to be charging normally!
Will post an update, but really seems like a forced discharge cycle to me too!!
Thanks for this thread, and I am interested in seeing if any more ppl are seeing such issues!
At least once, but sometimes twice a week, my battery keeps discharging while my Omnia 7 is attached to USB. And even the icon shows it should be charging.
The solution I use is taking the battery out for 10-15 seconds, put it back in, switch the device on, and charging works like it should be.
I hope they come up with a solution, because it's quite annoying.
Willem
Netherlands
EDIT: My model is I9505
Whilst on holidays, I took my phone out of my bag (when I knew it was getting close to flat) to find it not turning on. I assumed the battery was dead, but when I plugged it into the charger it didn't charge. I fiddled around a bit, and eventually got the vibration and charging light - but it kept turning off before the green battery came on saying charging. Being on holidays I didn't have my USB jig, or even external battery charger with me. I assumed it was a loose connection with the charging port - as every time I tried to plug it into charge it would only sporadically say that it was charging - but never get past the picture of the battery and the swirling icon (prior to the green battery coming up).
Upon arriving home, I got out my external charger, took out the battery, charged it for a few hours, then tried it. Again - it wouldn't turn on.
I then tried plugging the phone in again - but to the 800mA charging doc micro USB, insteead of the standard 2 amp. Straight away I get the charging picture, and the little graphic showing me the phone is about 1% charged. I leave it, the screen goes off. I come back 15mins later, the phone is RIDICULOUSLY hot, and the screen off. I unplug and replug to find the battery is still at about the same 1% level. I turn the phone on - it boots, shows 1/2% and then turns off as soon as I unplug it from the dock - even if I plug it straight into a 2 amp charger. I now decide that maybe the battery itself is the issue - and it's not holding charge. So I whiz out and buy two replacement batteries (MPJ ones, as they were fairly cheap - and this was just for the sake of finding the issue).
I charge one for about an hour on the external charger (the phone didn't turn on when I put the battery straight in). Then put it in - same deal. Nothing. I plug it into the dock micro-USB out to charge - again it comes up as charging, and shows at about 1%. I turn it on, and again am shown 1/2% charge, and again as soon as I unplug from the micro USB dock it turns itself off.
It is almost as if the phone isn't taking any power from batteries, and only direct from the power outlet itself. I'm unsure what could possibly have caused this. I can only think it may have been an external battery which I was using for a while on holidays (which had a 1amp micro USB out, that I was using to try and keep my phone charged). That is the only thing I have done different over this period (at least as far as I can recall!)
So basically - in short:
i) Phone won't turn on unless plugged in to a low amp charger (Computer USB, dock micro USB out etc)
ii) Even after charging batteries in external charger (two different external chargers have been tried) the phone is showing 1/2% battery
iii) The phone turns off a few seconds after I unplug it from the power source.
Any ideas!? I will take the phone to get repaired after Christmas (if they still repair it, as it's running a custom ROM).
BTW. a USB jig worked for the first time this afternoon - when I tried it not long after taking the phone off the dock. It's also worth noting that the phone is ridiculously hot when on the dock (around the camera/sim/micro SD area).
Googling there seem to be a few in similar situations.
This YouTube shows it
http://www.youtube.com/watch?v=U5B2By7fGII
Sent from my R821 using Tapatalk
abbaskip said:
Googling there seem to be a few in similar situations.
This YouTube shows it
http://www.youtube.com/watch?v=U5B2By7fGII
Sent from my R821 using Tapatalk
Click to expand...
Click to collapse
did you even try with a spare battery? can you check if your battery swollen? it might be the battery's fault
Repulsa said:
did you even try with a spare battery? can you check if your battery swollen? it might be the battery's fault
Click to expand...
Click to collapse
Hi, thanks for the response.
As mentioned in my first post, battery was what I thought was the issue at one stage, but I've tried two other batteries too. The original battery isn't swollen, but in any case I'm having the same issue with the other batteries.
I've tried charging them all on external charger before using them in the phone, and I get the same issues regardless of what I do.
It just seems strange that the phone switches on (now showing 0%) when plugged in, but not when unplugged.
And the batteries aren't being read properly, as they show 0% regardless of how long I pre-charge for.
Experimenting tonight, I've found that if I try to boot into recovery - even when plugged into dock, it dies before it even gets into recover.
Yet, if I boot the phone, I get to the main Android launcher/lockscreen before it dies...
Really has me baffled.
abbaskip said:
Experimenting tonight, I've found that if I try to boot into recovery - even when plugged into dock, it dies before it even gets into recover.
Yet, if I boot the phone, I get to the main Android launcher/lockscreen before it dies...
Really has me baffled.
Click to expand...
Click to collapse
Hello again, if you have any spare battery and its has 50 or 100% try to reflash the rom just to see the results. or try a different chargers and cables as well, If it all fails, i think you should send it to Samsung for the warranty. Software problems are somewhat easier to fix here than hardware, so your best option is to let Samsung handle it.
Repulsa said:
Hello again, if you have any spare battery and its has 50 or 100% try to reflash the rom just to see the results. or try a different chargers and cables as well, If it all fails, i think you should send it to Samsung for the warranty. Software problems are somewhat easier to fix here than hardware, so your best option is to let Samsung handle it.
Click to expand...
Click to collapse
Thanks again for your response, but you're clearly not reading what my issue is before making suggestions. As I have now said twice - I have tried three batteries, and batteries that I have charged for hours on an external charger before using. But they still come up at 0%. Not sure how you imagine I flash a ROM
It may be a matter of taking it to my dealer it seems. If anyone else has suggestions before I get to that (after Christmas) it'd be much appreciated
The batteries fully charged on external chargers and I'm still getting the same issues.
I'm hoping it's not kernel related. Can anyone confirm that if it makes it to download mode Werth a jig (but turns off after a few seconds) that this would be a hardware issue? It only turns on with the jig when it's straight off the charger though - so seems it's still not using the battery for power, almost residual power somewhere.
Sent from my R821 using Tapatalk
abbaskip said:
EDIT: My model is I9505
Whilst on holidays, I took my phone out of my bag (when I knew it was getting close to flat) to find it not turning on. I assumed the battery was dead, but when I plugged it into the charger it didn't charge. I fiddled around a bit, and eventually got the vibration and charging light - but it kept turning off before the green battery came on saying charging. Being on holidays I didn't have my USB jig, or even external battery charger with me. I assumed it was a loose connection with the charging port - as every time I tried to plug it into charge it would only sporadically say that it was charging - but never get past the picture of the battery and the swirling icon (prior to the green battery coming up).
Upon arriving home, I got out my external charger, took out the battery, charged it for a few hours, then tried it. Again - it wouldn't turn on.
I then tried plugging the phone in again - but to the 800mA charging doc micro USB, insteead of the standard 2 amp. Straight away I get the charging picture, and the little graphic showing me the phone is about 1% charged. I leave it, the screen goes off. I come back 15mins later, the phone is RIDICULOUSLY hot, and the screen off. I unplug and replug to find the battery is still at about the same 1% level. I turn the phone on - it boots, shows 1/2% and then turns off as soon as I unplug it from the dock - even if I plug it straight into a 2 amp charger. I now decide that maybe the battery itself is the issue - and it's not holding charge. So I whiz out and buy two replacement batteries (MPJ ones, as they were fairly cheap - and this was just for the sake of finding the issue).
I charge one for about an hour on the external charger (the phone didn't turn on when I put the battery straight in). Then put it in - same deal. Nothing. I plug it into the dock micro-USB out to charge - again it comes up as charging, and shows at about 1%. I turn it on, and again am shown 1/2% charge, and again as soon as I unplug from the micro USB dock it turns itself off.
It is almost as if the phone isn't taking any power from batteries, and only direct from the power outlet itself. I'm unsure what could possibly have caused this. I can only think it may have been an external battery which I was using for a while on holidays (which had a 1amp micro USB out, that I was using to try and keep my phone charged). That is the only thing I have done different over this period (at least as far as I can recall!)
So basically - in short:
i) Phone won't turn on unless plugged in to a low amp charger (Computer USB, dock micro USB out etc)
ii) Even after charging batteries in external charger (two different external chargers have been tried) the phone is showing 1/2% battery
iii) The phone turns off a few seconds after I unplug it from the power source.
Any ideas!? I will take the phone to get repaired after Christmas (if they still repair it, as it's running a custom ROM).
BTW. a USB jig worked for the first time this afternoon - when I tried it not long after taking the phone off the dock. It's also worth noting that the phone is ridiculously hot when on the dock (around the camera/sim/micro SD area).
Click to expand...
Click to collapse
In my view its a fault of charging IC . Since you have tried with replacing battery.
nishangrg said:
In my view its a fault of charging IC . Since you have tried with replacing battery.
Click to expand...
Click to collapse
Sorry, what is charging IC? If it was a charging fault, a fully charged battery would work wouldn't it?
So I took my phone to my SP - Telstra. The phone, being only about 6 months old, was still within warranty period. Not surprisingly, Telstra have said that as there is a Custom ROM on the phone, the warranty is voided. I stated that my understanding is that under Australian law, as it is a hardware fault, and not a fault caused by the ROM, the warranty still stands - however Telstra wouldn't budge and said I have 5 days to decide if I want to pay the $300+ for the repair.
What is my next course of action? Has anybody had a similar issue previously? Is the TIO the next port of call? Or should I be going to NSW Department of Fair Trading?
I'm sure I've read previously that phones are still covered under warranty after rooting etc, if it can be shown that it's a hardware fault, not a software fault. As the battery doesn't seem to be powering the phone, this clearly seems to be the case - esp. as it is the same in download mode and recovery mode.
Any help would be great. Please don't post pointing out that I rooted my phone so THAT's my own fault etc. These posts aren't helpful, I already have know that.
So I took my phone to my SP - Telstra. The phone, being only about 6 months old, was still within warranty period. Not surprisingly, Telstra have said that as there is a Custom ROM on the phone, the warranty is voided. I stated that my understanding is that under Australian law, as it is a hardware fault, and not a fault caused by the ROM, the warranty still stands - however Telstra wouldn't budge and said I have 5 days to decide if I want to pay the $300+ for the repair.
What is my next course of action? Has anybody had a similar issue previously? Is the TIO the next port of call? Or should I be going to NSW Department of Fair Trading?
I'm sure I've read previously that phones are still covered under warranty after rooting etc, if it can be shown that it's a hardware fault, not a software fault. As the battery doesn't seem to be powering the phone, this clearly seems to be the case - esp. as it is the same in download mode and recovery mode.
Any help would be great. Please don't post pointing out that I rooted my phone so THAT's my own fault etc. These posts aren't helpful, I already have know that.