Touch screen not responsive sometimes - Touch Diamond2, Pure General

Sometimes the touch screen is not responsive. I need to press screen at various places to get it work again.
Any idea why this is happening?
Due to ROM bug or Hardware issue?

It may sound funny but my TD2 is the same and after few checks I found a way to fix it..... You must look at your display in an angle and you can see that in the center is a spot which is darker than the other display, after this you must suck a little right above the spot and everything is back to normal....

use a duct tape to suck it
this might be caused by extra pressure was placed on the screen. I found out about this when I accidentally slept on my phone for a whole night

Related

Touch screen stopped working :-(((

Hi,
The touch screen part of my universal has ground to halt to the point that it won't work.
There doesn't appear to be any cracking and I don't recall dropping it or sitting on it.
I work a fair bit outside and can get quite a bit of dust and dirt in my pockets and am wondering if it could be due to dirt getting into the connect on the hinge.
Has any one else come across problems with the hinge?
I'm reasonably adept with a screwdriver - are there any things to watch out for when disassembling to check it over?
Hi..
If u can open with the Universal guide posted in the forum then try clean ing the connectors on the Right and Left of the Clamp Shell part with Iso Propyl Alcohol.
Before opeining you can try pressing mildly with yr fingers, at all the forur corners..it can start working..else do the above...
Hi,
OK, the screen seems to be working OK this morning, however I seem to be getting a sort of ghost effect where it appears as though the phone icon and the volume icons are getting pressed resulting in the volume controls and the phone/flight mode popup appearing on screen.
I guess it is all down to dirty connections.
Do you have a link to the thread about dismantling the hinge, I can't seem to find it.
Thanks.
re isopropal alchol
only use 99% alchol to clean contacts anything below that can cause corrosion on printed circut boards and contacts.
any progress yet.
mine stopped working today too.
but when i took off my screen protector, it worked for a while.. now its dead again.
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
being in Australia I go to the beach allot. with my jasjar.
the sand gets stuck in the sides of the screen putting pressure on the screen and disabling any input. just a thought that it could be the same with u.
hope u sort it out, otherwise claim it on warrenty sooner than later.
The problem I have with the screen is that occasionally the touch screen side of things appears to stop working and also the the volume, wifi and phone dialogs keep on appearing as if I am pressing the relevant icons in the top bar.
I'm guessing some dirt has got into it somewhere or there is a loose connection, but am struggling to open up the screen's case to inspect it.
6680abhi said:
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
Click to expand...
Click to collapse
i took off my screen protector and it worked an hour...
got home, prepared to go to the T-mobile store.. then cleaned my screen ( without protector ) with a small cloth and it was working again.. so weird..
lets wait and see what happens ..
It's not really that weird: If some dust, or something equally small gets between the screen and the plastic frame, it can put enough pressure on the screen, and so the touch screen takes it as a constant (or intermitent) input, invalidating any other action on the rest of the screen.
I just received my Aquapac waterproof (and sand/dustproof) to use my Jasjar hapilly in the beach! :lol:
oh so annoying, my volume sliders keep popping up now..., as if some one keeps tapping, cause when not in Land scape mode when i open the "START" menu. it scrolls down, the same input/tap as wher the volume is in Landscape mode
There must be something wrong ... my screen still isnt working properly
one possible solution for touch screen not working
guys.... although I dont need to register onto this portal and it took me 15 minutes to register (fault of my own) but I got so much relieved with the solution that it deserved 15 minutes of my effort ;-) I hope it helps someone...just like it did help me....
I own a P835 Asus mobile and from past 2-3 days was having problems - start menu continuously appearing and my taps not getting recognized. Since yesterday my screen suddenly stopped responding to any taps or scrolls altogether.... buttons were working fine but not the screen..... i spoke to the facilities centre this morning and was about to take it to the shop but due to my laziness...didn;t go.....
Thanks guys.... what you mentioned above is very correct.... it was just a tiny molecule of dust that the screen was interpreting as my input and finally refusing all my taps..... I just cleaned the screen and the speaker side with the mere stylus n things started working.... thanks a lot.... more than laziness was this worry cause I just bought this piece a month before....
so people...before takin it to the shop....try this one too.....huhhh.....

Keypad + screen issues (after reassembling)

I took apart my tytn, including the screen part.
After reassembling it, I've had random issues related to the keypad and screen.
By keypad, I mean all the keys on the screen part of the phone (D-pad, call/hangup,soft left/right, Internet Explorer & Email).
They will randomly cease working and randomly restart working (usually after turn on/off the screen with the power button)
The screen will also randomly turn white and come back on only if I turn off the screen and then back on.
Im thinking it has to do with a loose connection somewhere in the screen section of the phone, however, Ive taken it apart 2 more times to check everything out and the problem persists.
I wonder if anyone experienced the same thing and found which specific internal is the issue.
i would like to know too cause my buttons just stopped working. so the talk, end, message, Internet explorer, ect. but the left down up right and center button work.
I have the exact same issue.
All the keys (not keybord keys) randomly stops working. I am so used to it now, that I dont even try to answer the phone with the green key button.
The screen fades to white, sometimes (maybe 1-3 times a day).
The screen is white when awakening from "sleep mode", turning on and off the screen fixes that after a while (50% of the time white screen when from sleep mode).
I have found out that putting a finger nail between the keyboard and the screen, on the right hand side, when in closed position, and then putting the screen back on, gives me a 99% chance of funktional display.
The problem also accurs in the "full keyboard position", But putting the finger nail in the same spot helps.
So I think the problem of the connection is in the keyboard part of the phone, since those slide contact always are on the right hand side, and the display contact shift side.
I would lite to know if any body have a permanent solution for this.
(I have now opend my phone yet, and I have tryed the putting thin plastic between the display and the cover, with minimal success)
thanks for your time
alkizmo said:
I took apart my tytn, including the screen part.
After reassembling it, I've had random issues related to the keypad and screen.
By keypad, I mean all the keys on the screen part of the phone (D-pad, call/hangup,soft left/right, Internet Explorer & Email).
They will randomly cease working and randomly restart working (usually after turn on/off the screen with the power button)
The screen will also randomly turn white and come back on only if I turn off the screen and then back on.
Im thinking it has to do with a loose connection somewhere in the screen section of the phone, however, Ive taken it apart 2 more times to check everything out and the problem persists.
I wonder if anyone experienced the same thing and found which specific internal is the issue.
Click to expand...
Click to collapse
These are the exact symptoms of the "SCREEN FADING INTO WHITE" problem. See this thread for more info: http://forum.xda-developers.com/showthread.php?t=303872
The common causes for this are a bad connection to the D-PAD controller PCB (in the technical manual they mention it should be carefully checked and the really small screews with same torque making a 90 degree with the PCB), a bad controller (that was my case, had to order a new one) or not enough pressure on the square black chip on controller (some people seem to have fixed it by putting a plastic sheet in between the chip and the case, to apply constant pressure).
I suggest you try to re-open your phone and reconnect the D-PAD PCB as carefully as you can, double checking the connection and the screws there.
I did fix my problem, by ordering a new PCB and replacing the old (probably bad) one. It started to happen after I dropped my phone and it's the only thing that worked. Now my phone is as good as new.
Hope this helps!
Similar Issues with screen
I have similar issues;
Anything thats on the foreground gets closed by the 'x' button and if I slide it open the start button gets continually pressed!
Seems to be the top right corner of my TS thats at fault
sometimes it's fine....most of the time its not!
Andy.
I have the same! I have a huge dead spot in the middle of my (Tytn) screen, and if you tap there it actually activates the "ok" in the top right corner. The rest of the screen works ok. Whilst drawing in notes any drawing near the center dead spot results in a streak to the top right hand corner...
Bad screen?
Bad rom?
Bad motherboard?
lepic2019 said:
I have the same! I have a huge dead spot in the middle of my (Tytn) screen, and if you tap there it actually activates the "ok" in the top right corner. The rest of the screen works ok. Whilst drawing in notes any drawing near the center dead spot results in a streak to the top right hand corner...
Bad screen?
Bad rom?
Bad motherboard?
Click to expand...
Click to collapse
You can rule out the ROM and M/board in my view for this specific problem. Your issue is very similar (and I think has the same cause) as those who find programs close randomly when in portrait mode and when they open the keyboard the start menu often pops up untapped.
I think this is just a case of a bit of pressure being put on the screen top right corner. Some folks have tried the business card run around under the bezel fix and had some success others have had to return for replacement/repair.
Some have taken the device apart and removed the gasket around the screen under the bezel, but this is not guaranteed to work.
Others have replaced the screen and for this particular problem it is very rarely successful as the screen is not normally damaged.
If you have a warranty use it - all of the above "fixes" are warranty voiding.
Mike
Hi Mike
It's an interesting problem as when performing a click and drag in Notes (drawing mode) the center section of the screen seems to work normally - a square box can select an area right through the middle of the screen - suggesting that the screen (as you say) is OK. So what is causing the a tap in the middle of the screen to register in the top right hand corner, when we now know that the center of the screen can work and respond in the correct manner. The size of the affected area is about the size of a thumb print EXACTLY in the middle. Personally I would like to believe that performing screen alignment 4 - 5 times a day for the past year has worn out the center dot and that is affecting the surrounding area. The trouble is that this fault has been reported on this site a few times now, and everyone says it's caused by something else! What did I do immediately before this happen I hear you ask? I flashed a new radio rom and was fiddling with a piece of card I have wedged down the RHS side of the screen to try and help stabilise the screen alignment. Since this problem arouse, I have removed the gasket - but that hasn't fixed it. I'm going to try and boot up the phone out of the casing to see what "zero" pressure applied to the screen does.
I'll report back...
Lepic.
lepic2019 said:
Hi Mike
It's an interesting problem as when performing a click and drag in Notes (drawing mode) the center section of the screen seems to work normally - a square box can select an area right through the middle of the screen - suggesting that the screen (as you say) is OK. So what is causing the a tap in the middle of the screen to register in the top right hand corner, when we now know that the center of the screen can work and respond in the correct manner. The size of the affected area is about the size of a thumb print EXACTLY in the middle. Personally I would like to believe that performing screen alignment 4 - 5 times a day for the past year has worn out the center dot and that is affecting the surrounding area. The trouble is that this fault has been reported on this site a few times now, and everyone says it's caused by something else! What did I do immediately before this happen I hear you ask? I flashed a new radio rom and was fiddling with a piece of card I have wedged down the RHS side of the screen to try and help stabilise the screen alignment. Since this problem arouse, I have removed the gasket - but that hasn't fixed it. I'm going to try and boot up the phone out of the casing to see what "zero" pressure applied to the screen does.
I'll report back...
Lepic.
Click to expand...
Click to collapse
It will be interesting to see what results you get. You'll need the old rubber band technique to hold the battery in place while you do it!
Mike
Well it's not due to the case squishing the sides of the screen as I just dismantled my hermes, wired it all up in bits on my desk, powered it up and still the screen has a dead spot in the middle and phantom taps in the top right. Temperature is normal room temp, approx 22deg c today.
I'm not sure the exact mechanisms of how these touch screens work out where you are tapping (resistance, voltage), but it looks like there are 3 separate strips running around the screen. 1 goes straight across the bottom, two goes up the LHS and across the top and 3 goes up the RHS. Therefore there is a gap between strips 2 and 3 in the top RH corner. Coincidence? hmmm It seems to me for it to register a tap in the top RH corner, strips 2 and 3 would register low voltages (or high resistance) and bottom wouldn't register at all. Thus suggesting a fault with the PSU that powers the touchscreen. Taps near the edges work because they are near the edges and therefore the resistance is not too great and can be detected, taps in the middle and worse off because they are far from all the detecting edge strips.
Does anyone think that there might a registry tweak for boasting power to the touchscreen?
Hermes Whie Screen Problem
To fix the "white screen" problem, you have to take your unit apart, and reconnect the ribbon cable.
I have a new 8525 and it started happeneing to me, so I took it apart this week, and reseated the ribbon connector.
Fixed the problem.
Has anyone here read and understood all that is said here:
http://msdn2.microsoft.com/en-US/library/aa919680.aspx
Perhaps someone could compare the touch.dll in Black Majik to WM5 - should be the same right?
How come that HKLM/hardware/devicemap/touch doesn't show the touch.dll driver as drivername? Keyboard has it's driver...microsoft says it should say drivername = touch.dll
Do you all have that in your registry?

Blur screen

Hi
I don't know if any of you guys have problem like this or not, but screen on my topaz seems to got wet inside, when I place it against the light I can see that it is sort of wet inside the screen and the sencetivity of the screen has been dropped. Last night it seemed that the top layer of the screen sticked to the lower layer and I could see the sensor dots on the lower layer of the screen so it stopped the phone getting started.
I dont think I can use the gaurantee cause I modified the rum.
so wondered if you guys had the same problem, or I am open to any suggestions that what can be done.....
Thanks

Ghost screen touches

Just got myself a transformer today and it seemed great, however right after about 5 minutes the thing goes nuts like someone is swiping or touching the screen. Mostly just one spot on the left side and it will do it whether I'm holding it or it's sitting by itself. Can't seem to find anything posted about this wondering if thats because it's not common or I'm just not looking for the right stuff? Any help would be great, will likely return it tomorrow anyhow but if there's a fix would be nice.
Yeah, I got this as well while playing Angry Birds (F'd up my scores ! ). I don't know if it will work for you, but I just cleaned the screen really well with a cotton ball and alcohol, dried it, then used a microfiber cloth to clean it up (the ones that come with glasses, screen protectors). It worked for me, i think there was some gunk on the screen and was registering as a touch..
Try a factory reset and if it doesn't work take it back for a new one.
Thanks I can't see it being something on screen but will give it a wipe done here in a minute. Also tried the factory reset seemed to help but still getting in same frequency just not as badly. will see if the cleaning doesn't work I'll take it back and replace it.
This is the biggest annoyance that I have as of recent.
I have particularly oily fingerprints which causes smudges constantly.
I love the sensitivity of the TF, but if there is excessive smudging, the residue will register as a screen input - Wish the sensitivity could be adjusted.
Weird things happen when I need to clean the screen... I.E. I will be using a browser and use a single touch to scroll down, but it will zoom in/out instead; the long press menu will show up in a random spot persistently; -or- the screen will be completely unresponsive.
When this happens - I turn of the screen, clean it, turn the screen back on, and I'm good to go (note: sometimes I cannot even see any smudges where I am having issues).
This happens to me FREQUENTLY when i use the tab outside during humid days. I am thinking a screen protector may help, but still havent gotten one to try it out.
I had this same problem before the touch screen completely stopped responding on me.
For mine it only happened after waking it up from sleep mode though. When I turned Timeout to Never the ghost touching stopped.
Well tried as suggested the cleaning of the screen and all that but it still did it so took it back to the store got lucky and they still had one left, and exchanged it. New one hasn't had any issues at all. Thanks all.
I just took mine out of the box for fun (it was packed up for rma) and when i turned it on the touch screen worked. The ghost touching stopped to. But i still have a strip from top to bottom on the right side of the screen that registers two touches . So ill probably still send it in for a replacement.

Screen becomes unresponsive to touch frequently

I've searched a good bit and wasn't able to find any information regarding the exact problem I'm having.
Bought a used G6 for starters
No water damage indicated by the sticker
The phone works great on the home screen and app drawer
I turned on dev mode to show touches
When you're in the camera it will stop responding to touches, you can still take pictures using the side buttons. The screen will become responsive again after a couple minutes. This whole time you can take pictures and the screen is functioning just not responding to touch
This happens also when you're loading web pages, even a Google search the screen will stop responding to touch and then eventually start responding again for a short while till you load another page or start moving around the page too quickly it seems. However again the screen is functioning, video previews are playing, just no response to touch.
Loading a game like Asphalt 8 the phone doesn't respond to touches until a couple minutes after the game has been fully loaded.
Even after a hard reset/factory reset the screen will sometimes be unresponsive upon the initial welcome/setup screen and then it will become responsive and you can go through the whole setup without an issue.
Any insight? Any suggestions? If I can't figure it out I'll just get rid of it but it's in great condition a shame it just doesn't function properly.
Thanks in advance!
Looks like some sort of hardware issue...
But before you start to worry...
This might sound like a stupid question but have you tried cleaning your screen with some cleaning solutions?
Sometimes dust mixed with dried sweat can cause severe touch responsiveness issues even if the screen looks like it's clean.
This is an older thread, but maybe I can help someone.
I replaced a touchscreen on a LG G6 and saw that the touchscreen did not work if the back cover was not mounted correctly and the data transfer between the phone and the fingerprint sensor was interrupted. This may be a common problem for users because the connector is small and the back cover is attached with a double-sided tape nearby this connector. It seems that the touch screen is disabled by the phone software without the back cover.
MaBaGeMiFlo said:
This is an older thread, but maybe I can help someone.
I replaced a touchscreen on a LG G6 and saw that the touchscreen did not work if the back cover was not mounted correctly and the data transfer between the phone and the fingerprint sensor was interrupted. This may be a common problem for users because the connector is small and the back cover is attached with a double-sided tape nearby this connector. It seems that the touch screen is disabled by the phone software without the back cover.
Click to expand...
Click to collapse
Thank you so much for this comment!
My gf phone had problems lagging and becoming insensitive to touch, the problem got worse and worse, almost never responding anymore. Performed a factory reset etc, didn't help.
After reading your comment I tried pushing on the back cover while swiping. Now I'm able to revive the phone after pushing hard on the top and bottom left corners, of the back cover.
Thanks a mille !
Lg g6 has back panel from glass and under it you have contact for fingerprint sensor.Somehow if the back panel is loose it can cause touch fail,and you cant use the device touch function!
--->FIX:
So you will have to turn screen off using back button,and then try to press back glass on left and right side of the camera lens !
Then simultaneously press the power button and try to use the touch .
If it does not work tru again around camera lens and turn off screen each time you press the back glass!
For me it worked !

Categories

Resources