I currently have a sprint HTC Vogue and I am trying to flash the Verizon PRL onto it so I can use it on the PagePlus network. Everything I have seen says to dial #775#, but when I do that, my phone just tries to dial the number. I was using NSFAN's rom, and I even tried other roms and it does the same thing. Any help with this will be greatly appreciated.
opivy224 said:
I currently have a sprint HTC Vogue and I am trying to flash the Verizon PRL onto it so I can use it on the PagePlus network. Everything I have seen says to dial #775#, but when I do that, my phone just tries to dial the number. I was using NSFAN's rom, and I even tried other roms and it does the same thing. Any help with this will be greatly appreciated.
Click to expand...
Click to collapse
Which rom are you using now? If you are flashing a custom rom, more than likely you have a folder called "Phone Codes" somewhere in the Start menu. In there, you will have one that is called PRL. You have to have the MSL code to change this value though.
Get the PRL that you need and dump it somewhere in your phone. When you open the PRL program in phone codes (and you enter the MSL code), simply tap and hold where it says the PRL version and click on "Edit" (or whatever option you get), look for yours, and presto! Save, exit (you will be asked to soft reset).
Hope this helps.
Thanks. I have the MSL. I am flashing the official Sprint WM6.1 rom right now out of desperation, but I can put whatever on there. Do I need a custom rom in order to use the "phone codes" folder?
opivy224 said:
Thanks. I have the MSL. I am flashing the official Sprint WM6.1 rom right now out of desperation, but I can put whatever on there. Do I need a custom rom in order to use the "phone codes" folder?
Click to expand...
Click to collapse
To get it in folder format, yes. But if you are going for a stock rom, then simply use the codes and you'll be in good shape.
I want to change PRL in my HTC.
I can access to ##775#.
But I can't find anywhere to PRL file in my phone.
I want to change PRL by myself.
Sometimes, I can use my phone.
But most of times, it shown searching and if i got signal, it shown antenna only. So how should I do? Please help me.
thihaminhtun said:
I want to change PRL in my HTC.
I can access to ##775#.
But I can't find anywhere to PRL file in my phone.
I want to change PRL by myself.
Sometimes, I can use my phone.
But most of times, it shown searching and if i got signal, it shown antenna only. So how should I do? Please help me.
Click to expand...
Click to collapse
Have you tried to use the *228 (or whatever Sprint's equivalent is)? It should automatically provision your device.
opivy224 said:
I currently have a sprint HTC Vogue and I am trying to flash the Verizon PRL onto it so I can use it on the PagePlus network. Everything I have seen says to dial #775#, but when I do that, my phone just tries to dial the number. I was using NSFAN's rom, and I even tried other roms and it does the same thing. Any help with this will be greatly appreciated.
Click to expand...
Click to collapse
When I flashed my Sprint Vogue for Verizon usage... I first had to flash the newest stock Verizon ROM (You can find it on NuAngel's goodies page at the bottom! Yes the radio change one!), then flash a Verizon PRL to the phone. Nu told me I would have to reunlock the phone afterward, but I didn't need to.
I was then able to dial *228 and program the phone! After the phone was programed, I could finally flash ROMs onto it and still have working service. This phone didn't like NuVogue 5 (even though most of NuVogue's development was done on this phone.. wtf). Nu cooked a Verizon specific NuVogue 5 and it worked a bit better, but I remained on stock until I was able to cook my own build (still working on, I have plans on posting it after conferring with Nu and stealingz some of his ideas).
I can update the phone roaming via *228 only with the stock Verizon ROM (does not work on ANY cooked ROMS I have tried!!), but because the phone still has a Sprint PRI (feel free to message me instructions on switching to a Verizon PRI, cause I haven't found them yet), I get the roaming triangle. I used the latest moded PRL found in this thread here (51831) and I've been great ever since.
I try to avoid Carrier generic ROMs (or cooking my in development "XevRev" [tentative name] as generic) since they reflash the PRL, which is just a pain in the butt imo. I plan on trying NuVogue 6 when Nu and I go to hang at his place sometime this coming week, I want to see if its improved over the previous release on this phone. Can't explain why the release ran so waked out in v5 on this phone..... anyway...).
*links removed because I haven't been validated by the mods. I recommend site admin get a Stop-forum-spam (Google to find since I can't link) plugin for his vB forum. XD It's a lot easier then manually chasing down spam.. trust me.*
Related
Ok so I flashed my phone to metropcs but after seeing that this phone needs an steady connection to use it 100% .. I switched to Sprint, so they are going to send me some crappy phone this week, then I will attempt to activate my HTC hero .. take in consideation that I use it in metropcs, will I need to change some settings? Tower ? PRL?
Thanks
Wll i need to Flash to stock?
Your best bet would be to use the RUU here on the site and restore the phone to complete stock so activating it on sprint will not be trouble.
You can try to activate it first but i doubt data etc will work with sprint if it was flashed to metro PCS
will flashing RUU would set everything to default even the settings that i changed in Qpst / ##3282#???
Just RUU it back to sprint, it should restore the prl's and everything else without problems.
Go to the sprint website and do a ESN change to your hero whenever you are ready and click on manual configuration, it'll give you your MSL. You can use that number to restore the phone back to factory defaults. ##786# I believe is the code to reset the phone to factory.
Yeah I just checked. ##786# (Menu) (reset) (msl) ok.
Ok Thanks so much...Last question what RUU should i USE? there are 2 available 1.56.651.2 and 1.29.651.1... I am thinking in 1.56 but I want to make sure.
Ok I flashed to Stock...but It still on metropcs network...How can I configure it for sprint?
linkinx64 said:
Ok I flashed to Stock...but It still on metropcs network...How can I configure it for sprint?
Click to expand...
Click to collapse
reverse the steps you took to configure it for metro pcs you should have took notes on what the stock setting were right
The thing is I did not do it myself.. i took it to a store and they "flashed it"
so take it back to that store and tell them to flash it back
I might do that.. L( do you know the SID NID for Sprint? or the settings? that make a phone be in one network or another?
HTC Hero CDMA Sprint. Updated to Fresh 2.0d. Decided to try out the new radio image also: 2.41.05.02.03. Everything worked fine after ROM flash and radio update. I started to have a problem when I decided to do a PRL update also. Right after the PRL update, my phone doesn't recognize towers (no service). It shows PRL version as: 27392.
Any idea on what happened. I tried searching everywhere for a similiar problem/solution, but couldn't find any. I also tried to Update PRL and profile. Neither work. Please help.
EDIT: Under network, it shows "Searching for Service", 0 for "Signal Strength" and out of service for "Service State". I also tried re-flashing both the radio img and ROM over again. No luck. Restarting doesn't fix either.
mar122999 said:
HTC Hero CDMA Sprint. Updated to Fresh 2.0d. Decided to try out the new radio image also: 2.41.05.02.03. Everything worked fine after ROM flash and radio update. I started to have a problem when I decided to do a PRL update also. Right after the PRL update, my phone doesn't recognize towers (no service). It shows PRL version as: 27392.
Any idea on what happened. I tried searching everywhere for a similiar problem/solution, but couldn't find any. I also tried to Update PRL and profile. Neither work. Please help.
Click to expand...
Click to collapse
that does seem strange. be sure you are not roaming and flash back to fresh 1.1
as the prl is in the /radio partition the rom can not change it. on fresh 1.1 update your prl, and profile. that should fix it. good luck
Going to try a revert to Fresh 1.1. I am not roaming BTW (in my house that has service). It has 'signals bars' with an X. Thanks for the fast reply btw
Reverted to Fresh 1.1. Booted up with signal bars and large X over them... no service. Tried to update PRL and profile. Neither worked. Error code 1012.
What is Fresh 1.1? (n00b here)
When I had error code 1012 and no service, I had to hard reset to the phone's factory ROM, and do ##786# - Menu - Reset - MSL - OK and then after reboot do profile update. Key is doing the reset from the factory rom.
MSL might work I am hoping, but believe I would have to call Sprint for the MSL #.
Think 1.56 RUU would work? How about manually changing the PRL or downgrading the baseband?
Try flashing flipzmodes latest ROM, I know for a fact it automaticallyupdate your PRI!
Nevermind sleepy, your talking about your RPL!
mar122999 said:
Reverted to Fresh 1.1. Booted up with signal bars and large X over them... no service. Tried to update PRL and profile. Neither worked. Error code 1012.
Click to expand...
Click to collapse
you need to do the MSL code fix ...that should reset everything and fix your phone..
I had this as well.
First look at the DamageControl 2.1 R05 or whatever thread, his newest one. If you look on the first page it will have a download for the latest prl file, which is 60663, unzip the file and put it on your SD card. I then called Sprint and told them my phone started saying no service. After the normal stuff the guy said he wanted to send me to the advanced group, because he didnt just want to wipe my phone. Now when I got to that group the lady told me to try ##xxxxx# and some other stuff, and I thought hrmm sounds like an MSL number so I asked her what it was and she just said ohh thats something called MSL. After all of the stuff she tried didnt work they said they would send me a new phone since mine was under warrenty. Since I had the MSL I went in did ##PRL# and entered it, told it to look at the sdcard for /60663.prl and the update happened and my phone is back to normal. Now you can just manually do the update and not worry about it using the rom
i had the exact same problem yesterday. i was in chat with tech support for over 2 hours tryin to figure it out. what your are going to have to do is reprogram your phone like its the first time you got it. but program it manually. they can walk you through it. get your msl number from them. its a pain in the but but after all that when you go to program your phone. i flashed fresh 1.1 and everything was fine. it was stuck roaming because the prl was so low i did a prl update and everything went back to normal flashed back to fresh 2.0d and everything works fine now.
didn't even think to try what ^^^ did. so go ahead and do that probably save ya more time then i spent lol
dynamicpda said:
What is Fresh 1.1? (n00b here)
When I had error code 1012 and no service, I had to hard reset to the phone's factory ROM, and do ##786# - Menu - Reset - MSL - OK and then after reboot do profile update. Key is doing the reset from the factory rom.
Click to expand...
Click to collapse
Fresh 1.1 is a Rom I had this a while back 1012 is a data error! That came from a call to Sprint. You need to update the profile on a 1.5 Rom I used Gumbo 1.5c. The device service works better on 1.5.If you check the PRL did update. After talking to Sprint tech support that is what they will have you do.
This happend to me too, I went into settings, changed it into roaming so I could get a signal and updated the PRL. worked fine.
FIXED:
I called sprint this morning and she set my phone to automatic (so it would roam). It picked up a roaming tower fine. Then she told me to go update the PRL. I did this and it updated successfully. After that, it worked fine on sprints towers
Big thanks for the help guys.
Yeah, I updated my PRL and I couldn't get service. I switched to allow roaming to get a signal, then updated my Profile and PRL once again and the PRL switched to 60663.
I had this exact problem too yesterday. Even an ruu wouldn't fix it. I went to the sprint store and they gave me a new phone. The people there had never seen the problem before.
This is strange... I got the 1012 error when I tried to update my PRL, but it still updated even though it got the error... strange haha. By the way, I'm running TrevE's newest mod of the new Damage rom.
This is a custom ROM that allows root users to customize their settings and such.
I updated my prl through the device self service option and got that 2 something prl. So I went and tried updating through settings and it worked fine.
I was in the same situation, it updated my PRL to like version 17062 or something like that. Needless to say, I didn't have any signal and all I could do was roam. So I turned my phone off, back on, went to update PRL and it updated me to 60663 Fixed itself basically!
Got the Droid X to activate it on Alltel like I did very successfully with my Eris.
Installed HW virtual serial port software, created the virtual serial port, phone was detected and showing up correctly in QPST, went directly to CDMA Workshop and ripped the NV file from the phone, edited all the NV information to alltel's 3G provisioning with a HEX translator, uploaded the NV file to the phone and uploaded the Alltel PRL... all seemed well. Restarted the phone, it now shows no service. When I go to Settings, it tells me the baseband version is "unknown" and it doesnt know the ESN or anything, that isn't good. I tried reconnecting to CDMA workshop, if I try to restore original NV file, it doesn't know the SPC anymore so it doesn't allow it, SPC 000000 isn't recognized now. How can I recover the radio ? I tried restoring it (hard reset) through the settings, security menu AND the Power+home buttons way. After restoring, still no service and SPC is still incorrect, how do I get the radio back to default values ? CAn I reflash the phone? Anyone know where the factory rom is so I can do this ? Ah man, help me please :O
Other than that, I guess I'll have to have motorola take a look at it since I don't have it signed up to a verizon account, my bet is that verizon won't help me. thanks
Did a system "full reboot" help any??
No it hard resets normally and reboots to the welcome wizard, functions perfectly, but still "No Service" and "unknown" baseband in the settings...
I'm thinking I'll have to have the stock Rom file to flash my phone, hopefully this will flash the factory baseband too or maybe tomorrows update will fix my broken baseband, looks like from the information, it updates the baseband, wonder if it will update a totally dysfunctional baseband?
Yikes,.. this blows.
I don't understand why you didn't back up the rom if you were attempting something like this.
There is a Droid X update coming pretty soon, so I'm sure by that time the new rom will be available.
Well, I backed up the NV items, I figured that would be sufficient, guess not, Trial and error I suppose, but you're right.
What software do I use to back up the rom of the Droid X ? I know there is a key sequence on the Droid, what about the droid X ? The recovery screen (Power + Home) brings me to a menu allowing system recovery/wipe install update.zip from memory card, and thats it.
I have a buddy right here in town down the block that got the droid x with me, can I back the rom up off of his and flash that rom to my phone?
Help is SO appreciated...
EDIT
The system dumps that are floating around the web, is that a ROM backup ? http://www.droidxforums.com/forum/droid-x-hacks/114-new-droid-x-retail-dump-straight-out-pot.html
Can I put that file in the SD card as update.zip and flash it?
stevey500 said:
Got the Droid X to activate it on Alltel like I did very successfully with my Eris.
Installed HW virtual serial port software, created the virtual serial port, phone was detected and showing up correctly in QPST, went directly to CDMA Workshop and ripped the NV file from the phone, edited all the NV information to alltel's 3G provisioning with a HEX translator, uploaded the NV file to the phone and uploaded the Alltel PRL... all seemed well. Restarted the phone, it now shows no service. When I go to Settings, it tells me the baseband version is "unknown" and it doesnt know the ESN or anything, that isn't good. I tried reconnecting to CDMA workshop, if I try to restore original NV file, it doesn't know the SPC anymore so it doesn't allow it, SPC 000000 isn't recognized now. How can I recover the radio ? I tried restoring it (hard reset) through the settings, security menu AND the Power+home buttons way. After restoring, still no service and SPC is still incorrect, how do I get the radio back to default values ? CAn I reflash the phone? Anyone know where the factory rom is so I can do this ? Ah man, help me please :O
Other than that, I guess I'll have to have motorola take a look at it since I don't have it signed up to a verizon account, my bet is that verizon won't help me. thanks
Click to expand...
Click to collapse
why not use QXDM to modify the ESN?
Worth a shot...
You can try using the motorola troubleshooter. Its what they use to update your phone anyways and since the new update came out you might be able to install over what you did...I cant post a link because Im new but follow the instructions below and it will walk you through the update process via computer. I figure with a phone thats not working its worth a shot.
Go to Motorola's website and click the droid advert right on the left side of the screen.
Under the "Support" tab in the upper right hand corner is another tab called "Owner Support" click on that.
On the left hand side there are more tabs so this time click on "Update My Software"
It will give you a list of options, choose "Via Computer"
From here it will check your computer for their software and prompt you to download it. Its the troubleshooting software and it will ask you a few questions, its also what they use to update your software via computer so it may be capable of flashing your phone for you. Best of luck and let us know what the end result is.
I haven't tried either of these... but I'm about to start flashing a droid X to cricket and bookmarked these posts in case I mess something up. Proceed with caution as I have no first hand experience with these.
I'm still trying to get a handle on if the service programming parameters (the spc, MDN, MIN, SID, etc.) are updated as part of baseband updates, it sounds like they are since they are saying the device needs to be re-activated after applying either of these updates.
If a baseband update refreshes the service programming parameters here are the two ways I've found of updating the baseband:
Here's a link to a post for updating the baseband portion of your device (without updating the ROM):
http://alldroid.org/Default.aspx?tabid=62&g=posts&t=246
I don't know if this will work on a device that doesn't have a valid baseband prior to the update. Regardless, if your phone is bricked this may be a valid option to try.
There is also a 2.1 SPL file floating around which is the entire system image, the baseband and the rom. You will need to use rsdlite to apply this image to your phone. DO NOT APPLY THIS IF YOU ARE RUNNING FROYO.
Well, I was trying a few roms a few days ago and later i decided to go back to stock, I accidentally let the customizations run, and it went back to verizon, but i flashed the 0068 (or something like that) PRL file to the phone using EPST, after that I dialed *228 and updated the PRL to 02004 (latest MetroPCS PRL file), but i still cant use it, (i realized just 5 mins ago, 2 days after prl flashing -_-) I called the customer support just now and they said they just reset the device and I should shut it down and restart it, so anyways my question is:
I can't use my phone, I cant call, text or use web, and no one can call me, it says service not activated when i try to connect to the internet, and I cant use my voice mail either(LA 01 message something error) What should I Do?
Thanks guys.
taha1112 said:
Well, I was trying a few roms a few days ago and later i decided to go back to stock, I accidentally let the customizations run, and it went back to verizon, but i flashed the 0068 (or something like that) PRL file to the phone using EPST, after that I dialed *228 and updated the PRL to 02004 (latest MetroPCS PRL file), but i still cant use it, (i realized just 5 mins ago, 2 days after prl flashing -_-) I called the customer support just now and they said they just reset the device and I should shut it down and restart it, so anyways my question is:
I can't use my phone, I cant call, text or use web, and no one can call me, it says service not activated when i try to connect to the internet, and I cant use my voice mail either(LA 01 message something error) What should I Do?
Thanks guys.
Click to expand...
Click to collapse
The only thing that comes to mind would be for the VZW customizations to actually modify more than just PRL (but mess with other EPST settings as well). Just to confirm, did you have your phone working on Metro before this?
yes, it was working perfectly, even the mms and web were working :|
EDIT: I can call *611 and *228, oh wait i think i said that in the first post...
taha1112 said:
yes, it was working perfectly, even the mms and web were working :|
EDIT: I can call *611 and *228, oh wait i think i said that in the first post...
Click to expand...
Click to collapse
If you had 2.31 installed, the device should still be unlocked. Try running a hard reset/flashing another rom and see if that helps. I have a feeling that you will need to go into EPST and play with your MSID and MIN values and a few other things as well.
egzthunder1 said:
If you had 2.31 installed, the device should still be unlocked. Try running a hard reset/flashing another rom and see if that helps. I have a feeling that you will need to go into EPST and play with your MSID and MIN values and a few other things as well.
Click to expand...
Click to collapse
I hard reset on stock rom and didn't let the customizations run, then flashed 3.42.30 (alltell rom i think) and with out resetting the device I just put the nfsfan's rom in the sd card and flashed that, it still didn't help, can someone give me the settings for the PST.
Thanks for the reply
taha1112 said:
I hard reset on stock rom and didn't let the customizations run, then flashed 3.42.30 (alltell rom i think) and with out resetting the device I just put the nfsfan's rom in the sd card and flashed that, it still didn't help, can someone give me the settings for the PST.
Thanks for the reply
Click to expand...
Click to collapse
3.42.30 is a radio and not an actual rom. My guess would be that, unless you have them stored somewhere else, you will need to call Metro and ask them to help you re-program the phone. Couple of pointers:
a. Don't tell them that you have a Vogue (let alone a Vogue running 6.5) since they have little/no experience with WM devices.
b. Using BAFMSL, get your MSL from your device (you will need this to unlock and edit the EPST parameters. My guess is that you read the ESN to the Metro rep, who calculated an MSL, which of course did not work (here I am assuming that the ESN on your device has been cloned from another phone)).
c. What you want to get out of the rep are the numeric parameters for:
MIN (normally your phone number)
MSID
HomeSID
Don't assume that he/she will be able to guide you through the editing process because they simply won't know how. A simple "yes, go on" every time they tell you to change something will suffice. Just make sure you write the numbers down in a piece of paper.
Do this and get your numbers. If they are any different from the ones that are currently loaded, then your issue will be solved.
Just thought of one other thing. You said you went back to stock Verizon. Which radio did you have before that? And what radio did the Verizon rom take it to?
well, I had it metroflashed, and i can't do it again as i don't have any money now (only 15 years old xD), it has original ESN, does this change anything?
and btw, i can edit the epst, (the code is six 0s) or i may be wrong )
taha1112 said:
well, I had it metroflashed, and i can't do it again as i don't have any money now (only 15 years old xD), it has original ESN, does this change anything?
and btw, i can edit the epst, (the code is six 0s) or i may be wrong )
Click to expand...
Click to collapse
Nah, Metroflash via Houdinisoft does two things:
1. It will add the ESN into Metro's database and will link it to your account.
2. It may provision your phone. I say may because I have seen, more often than not, that Houdini fails to provision any device that runs WM.
Asking you again about the radios. What radio did you have prior to flashing to Verizon stock and what did the stock flash the radio to?
egzthunder1 said:
Nah, Metroflash via Houdinisoft does two things:
1. It will add the ESN into Metro's database and will link it to your account.
2. It may provision your phone. I say may because I have seen, more often than not, that Houdini fails to provision any device that runs WM.
Asking you again about the radios. What radio did you have prior to flashing to Verizon stock and what did the stock flash the radio to?
Click to expand...
Click to collapse
well I had 3.42.50 (bell i think), with super froyo 2.2, when I installed verizon stock rom it changed back to 3.37.(something), does this answer your question?
Thanks for helping me btw.
taha1112 said:
well I had 3.42.50 (bell i think), with super froyo 2.2, when I installed verizon stock rom it changed back to 3.37.(something), does this answer your question?
Thanks for helping me btw.
Click to expand...
Click to collapse
Yes, I was asking because I was afraid that you went below 3.xx.xx on the radio as this has been known to cause issues, including leaving phones completely useless.
Did you get the parameters from Metro as I suggested earlier?
well I got rid of the phone, as the representatives were not helping me at all (I talked to 5) so I am just going to buy a LG rumor touch (virgin mobile) and my other choice is Tmobile G1 but can I get it without a data plan?
taha1112 said:
well I got rid of the phone, as the representatives were not helping me at all (I talked to 5) so I am just going to buy a LG rumor touch (virgin mobile) and my other choice is Tmobile G1 but can I get it without a data plan?
Click to expand...
Click to collapse
Only if you buy it without contract (the G1, that is). Sorry that you couldn't get it to work. I am sure that it was only a matter of re-programming the device.
So I have been using MetroPCS on my Moto G5 Plus since I got it. Well today I went and activated my device with the Sprint network... It wasn't working when I left the store, and I told the rep how it was modified (using RessurectionRemix 5.8.4 Final), that I would work on setting it up.
Well, so far no success in activating it... Have tried changing network mode to CDMA/LTE and messing around with dialer codes, still can't get anything besides "emergency calls only."
Anyone have experienced getting this phone activated with Sprint?
Note: they did tell me they didn't have the exact, or "recommended," SIM card for my device, and that it was a secondary option they used in the system(?).
laserswift said:
You need to get the Sim card part # that ends in 446c. I got mine at best buy for 10 bucks and it's currently working well with Sprint.
Click to expand...
Click to collapse
I am using that SIM, got it working when I reflashed stock. Did not work again when I restored RR, at least fully, as I was able to get data to work minus SMS/calls.
I'm on Sprint. No issues with any Roms.
You need to be on a stock build for the initial setup, because the custom roms remove all of the PRL stuff. Once it is setup once, flash whatever you want.
Karlinski said:
You need to be on a stock build for the initial setup, because the custom roms remove all of the PRL stuff. Once it is setup once, flash whatever you want.
Click to expand...
Click to collapse
It doesn't stick after I flash a custom ROM
That's really odd. I don't have that problem...
Make sure you have APNs on the custom rom. I saw a problem a while back that the custom rom didn't keep the APN for some reason, and I had to put it in manually. Different device, but same problem.
Karlinski said:
That's really odd. I don't have that problem...
Make sure you have APNs on the custom rom. I saw a problem a while back that the custom rom didn't keep the APN for some reason, and I had to put it in manually. Different device, but same problem.
Click to expand...
Click to collapse
Can you tell me what your APN info is? I have data and calling working now, but no LTE option (see screenshot)
I have mine set to global.
I had this same issue with my s6, and I ended up having to factory reset the phone, and redoing the PRL update, and the option finally came back.
Just to follow up, I was able to get full LTE and calls to work by flashing stock ROM, updating PRL, and by then it was provisioned on the Sprint network.
As it stands now, if I reinsert my MetroPCS sim card, it is provisioned for MetroPCS no problem, but I do have to reflash stock again each time I want to provision for Sprint.
So thats how I am going to run things for now, by making backups and getting it provisioned using stock before restoring.
this worked for me
sharpsan said:
Just to follow up, I was able to get full LTE and calls to work by flashing stock ROM, updating PRL, and by then it was provisioned on the Sprint network.
As it stands now, if I reinsert my MetroPCS sim card, it is provisioned for MetroPCS no problem, but I do have to reflash stock again each time I want to provision for Sprint.
So thats how I am going to run things for now, by making backups and getting it provisioned using stock before restoring.
Click to expand...
Click to collapse
theres an ap on the play store called apn backup and restore. install it on stock rom . b4 using it u need to go in system/apps and move the apk to system/priv/apps once moved changed permissions to r-w-r-r. after that a quick reboot and open app change setting to disable ics check and do a backup . once finished do the same thing on new rom and mine works flawlessly. im on boost which is also on sprint network. good luck hope this helps