Hi, I have a T-mobile USA HD2 and when i make a call the screen no longer works. I cant press the anything on screen which means i can't delete voice mails. I have tried keeping the phone down so I don't activate the proximity sensor but the screen still does not work. Anyone having this problem as well?
Proximity Sensor... Display is blank, when something is in front of the sensor. This sensor located next to the light sensor
no, even when I don't activate the senor the screen does not work. I can see all the buttons and the picture of who I am calling. I try pressing them but nothing works.
You should have paied more attention to the several threads on this matter that have been published in these forums (that is, searching) but anyway, what usually causes this is enabling "Increase tap time" in BsBTweaks. If you have that one, unckeck that option.
thx worked. I did search but was unable to find anything about it
2 of the top four hits give the correct answer.
http://www.google.com/m?client=ms-o...&q=+leo +hd2 during call screen stops working
hint when searching google. include the following in your search
+hd2 +leo
This has been happening pre and post Nodo on my focus. If i'm on a phone call for at least a few minutes, then pull the phone away from my head, the phone's display should become active, but it isn't.
Anyone else having this issue or is it time to exchange the phone?
I have the same issue also it seems like I have to press the power button a couple of times to get it back.
Sent from my SGH-i917 using XDA Windows Phone 7 App
I'm also having this issue. Anyone remember if ther were having it pre-Nodo? Just wondering if the update changed something.
Regardless, it's a bit of a PITA.
I experienced this after having to replace a cracked screen. I just recalibrated the proximity sensor with my finger about an inch away and it worked fine.
ArcWhistler said:
I experienced this after having to replace a cracked screen. I just recalibrated the proximity sensor with my finger about an inch away and it worked fine.
Click to expand...
Click to collapse
How did you do that?
Yeah, ditto that - how do recalibrate the sensor?
Samsung Diagnostic App.
http://forum.xda-developers.com/showthread.php?t=839154
I was pecking around the screens months ago, and there was one bank of tests (multi-touch, red, green, blue, white, battery, etc, etc) that allowed setting and viewing the proximity sensor.
I remember playing with moving my hand closer, and further and watching it change from sensed to clear.
Sorry, can't remember which codes now.
I used the Wiki:
http://forum.xda-developers.com/wiki/index.php?title=Samsung_Focus
LCD Test - *#0*#
Ok, mine says No Detection. Is there anyway to set the value?
One other thing to note, about the samsung focus specific update regarding disabling the touch sensitive buttons while in a program, that also isn't working for me either. Not sure if they are related, but thought I'd throw it out there.
And as far as calibrating goes, not sure it would help since the problem only occurs while I'm on a longer phone call. On short ones the proximity sensor works just fine.
If you move your finger closer to the sensor, it should eventually change to Detected. The "set" button at the bottom should set the proximity sensor to the new distance. Mine is around 75.
ArcWhistler said:
If you move your finger closer to the sensor, it should eventually change to Detected. The "set" button at the bottom should set the proximity sensor to the new distance. Mine is around 75.
Click to expand...
Click to collapse
Mine says No Dectection. It has Prox Sensor: XXX I've taken my entire hand and covered my phone. NOTHING. When I push SET, It says ProxThreshold :0. Is there anyway to set it manually?
samsung focus post nodo
I believe the prox sensor issue is happening post nodo, I have never had this problem prior to the update... I have been able to fix it temporarily by pulling the battery and starting it up... don't know how long the fix works... got to do some testing... I am wondering if its a power thing as the screen wouldnt work when you plugged it in to power and had on a soft surface....
Still nothing. I didn't want to hard reset since I have Chevron installed. For some reason I did four updates on my phone and don't have a single backup. If I hard reset I'm S.O.L. with Twin Blades and other homebrew apps
What value does it show when you press the Reg button?
I've had issues with my earring tapping the screen while I talk and I had it fixed before NoDo, but the values reset when it was installed, they also appear to be different values now as my screen got supper finicky after the update. I was constantly hanging up or scrolling through multiple pages of stuff with my ear and you could see the screen turning on and off. I ran the proximity calibration while holding my hand in front and set to it to 1.
If it shows xx have you tried setting the value with nothing in front of the phone to see if it will at least zero out?
BooR4dley said:
What value does it show when you press the Reg button?
I've had issues with my earring tapping the screen while I talk and I had it fixed before NoDo, but the values reset when it was installed, they also appear to be different values now as my screen got supper finicky after the update. I was constantly hanging up or scrolling through multiple pages of stuff with my ear and you could see the screen turning on and off. I ran the proximity calibration while holding my hand in front and set to it to 1.
If it shows xx have you tried setting the value with nothing in front of the phone to see if it will at least zero out?
Click to expand...
Click to collapse
It has a big red box. It says No Detection. Prox Sensor:XXX Do I press Set or Reg?
another thing is wrong
seems like my light sensor is fried as well... I am starting to wonder if it's because of bad placement of the usb port... both lay right in front of the port, can't imagine pluging in and unpluging the phone would help if the sensors are right in front. I can't get either sensors to work anymore, even with a battery pull... does anyone else have this issue? goto the diagnosis menu and type
*#05#
you should be able to run through all the tests, I skip the feedback loop... Start at 1 and work your way through.
My Prox sensor says, no sensor XXX, and my light sensor is stuck with a value and will not change even when I cover the sensor... looks like a warranty replacement... how does this work with a sd card installed, the official WP7 ATT certified 8GB? Anyone else have to do this?
rockclimbaudiextreme said:
seems like my light sensor is fried as well... I am starting to wonder if it's because of bad placement of the usb port... both lay right in front of the port, can't imagine pluging in and unpluging the phone would help if the sensors are right in front. I can't get either sensors to work anymore, even with a battery pull... does anyone else have this issue? goto the diagnosis menu and type
*#05#
you should be able to run through all the tests, I skip the feedback loop... Start at 1 and work your way through.
My Prox sensor says, no sensor XXX, and my light sensor is stuck with a value and will not change even when I cover the sensor... looks like a warranty replacement... how does this work with a sd card installed, the official WP7 ATT certified 8GB? Anyone else have to do this?
Click to expand...
Click to collapse
same problem here. seems like those two sensors are burned
For the last 2 or 3 months I've noticed my proximity and light sensor don't work on my Focus 1.3.
The screen doesn't turn off while on a call and the camera button can wake the phone with the screen turned off.
I've also seen that the screen doesn't auto dim any longer when in a dark room.
I held off on doing the warranty swap with ATT because I thought Mango might fix it but I haven't had any luck.
Do you have any suggestions?
When you mean the camera button wakes the phone up, does it launch the camera app, or is it like the power button is pressed (when the screen is off)?
Archange1 said:
When you mean the camera button wakes the phone up, does it launch the camera app, or is it like the power button is pressed (when the screen is off)?
Click to expand...
Click to collapse
That I have seen was a setting I had in the camera settings but the rest I've seen still stands.
Diagnosis app
So basically you need to recalibrate your proximity and light sensors with the diagnosis app. Please read the sticky thread for diagnostic codes. This issues has been discussed. Off the top of my head I can't remember the codes how to do it. I would search the forum for proximity sensor and light sensor recalibration.
Update-
1. If you don't have the diagnosis app you need to type ##634# in your dial pad
2. type *#0*# - diagnosis app not the dial pad
3. Recalibrate the Light and the proximity, then restart your phone. Should be fixed.
As for holding the camera button and the screen lights up. That is an advantage/shortcut to get to picture mode. That setting can be disabled if you go
1. Windows home live tile screen
2. settings
3. Swipe over to applications
4. pictures + camera
5. disable press and hold camera to wake up the phone or enable prevent accidental camera lauch when phone is locked
siralex241 said:
So basically you need to recalibrate your proximity and light sensors with the diagnosis app. Please read the sticky thread for diagnostic codes. This issues has been discussed. Off the top of my head I can't remember the codes how to do it. I would search the forum for proximity sensor and light sensor recalibration.
Update-
1. If you don't have the diagnosis app you need to type ##634# in your dial pad
2. type *#0*# - diagnosis app not the dial pad
3. Recalibrate the Light and the proximity, then restart your phone. Should be fixed.
As for holding the camera button and the screen lights up. That is an advantage/shortcut to get to picture mode. That setting can be disabled if you go
1. Windows home live tile screen
2. settings
3. Swipe over to applications
4. pictures + camera
5. disable press and hold camera to wake up the phone or enable prevent accidental camera lauch when phone is locked
Click to expand...
Click to collapse
So this should work for both?!
This makes me very happy! I'll report back soon.
Huh when I get into the Proximity recal it only shows XXX (No Detection) and never changes anything.
Am I doing it wrong?
EDIT: The value reported for light is staying at 0000 too.
http://forum.xda-developers.com/showthread.php?t=1045167&highlight=proximity
Is hinting that I have a busted set of sensors and will need to warranty it.
play with the set and reg button. Also, restart the phone to see if it will work. Not to insult your intelligence but you know where the proximity and light sensor are right? Hold your finger in front of it on it moving it further and closer. If none of these work you might have defective sensors. I like to try everything a couple of time before I take it in for warranty.
I do know where the sensor is, right next to the earpiece.
I've restarted the device and tried the sensors again but no luck.
When I try to set the light value at something I get some error about "Light_SetCalValue : DeviceloControl failed" and for the proximity test the screen always stays red even if I cover the whole phone with my hand.
I'm in the same boat. I've been debating on just rolling all the way back to stock and starting all over. Of course if it is a hardware issue I'm just going to be wasting time. Then again it probably would be best to roll back before sending it in on a warranty issue...
My other concern is if they do cover it what am I going to get back? Don't really want to be stuck on a Rev 1.4 focus as that STILL seems to be causing issues.
I hear ya tanders04, it would stink to get a 1.4 back.
Also, thank you siralex241 for the help.
Hi everyone,
since a few weeks i got problems with the proximity sensor on my i9505
First i thought that it is software related but after clean installing a new ROM yesterday i see that the problem still exists...
It happens when the proximity sensor should react, when i am close to it, it reacts and activates but the problem is that it wont turn off again...
i dialed the test menu and went to sensor test, as i see the sensor sees the distance normaly, when i bring it close and when i move it away i see that the numbers react how they should, however after the sensor is once trigerred with a close object it starts to vibrate and the screen turns green (how it should), but after moving away it registers the distance but it won´t stop to vibrate and turn off :/
Anyone who knows what could be wrong?
I have to mention that the display was changed once (because of the glass broke) but it was working normal for months...
EDIT: after testing again i see that the sensor sees the distance just as it should the only problem is that once that the sensor action is triggered to 1.0 from 0.0 it stays at 1.0 no matter if i remove my hand...
I'm having a problem with proximity sensor: every time it gets on, it's stays on. I mean, when I make a call, it works as is suposed to work. But when I hang up, block the screen or wherever I do, the sensor is still on. If I pass my finger, it "blink" stronger, like detecting my finger. When I restart the device, it get off.. but when it get used again, it happens the same.
Anybode has the same issue?