Related
Hello. I'm having major issues installing Touch-IT wm6.1 19199.1.0.0 - Full. I've installed at least 5 ROMs on my phone and have never ran into any issues. When I try to install the ROM it gives me error 270: The image file is corrupted. I've done Hard SPL and even installed the original TMO ROM but I cannot get any other ROM installed. Any help is appreciated. Thanks in advance.
uninstall and reinstall activesync
Hard SPL
i have readed all Guide, downloaded ROM " HardSpl_WM6 "
but when try to UPDATE it show me image version which is lower than mine and after cliking next, error message comes " ERROR 202"
tryed to uninstall "Activesync" and install again.. still same problem.. tryed 3 diferent HARDSPL... same problem.. need help.
Are you trying to flash an LZX compressed ROM through Activesync instead of via your SD card? Sounds like you are.
solved.
i solved. The problem was that i was using USB hub to connect. All now is OK, already installed WM6.5.. working good..
Please let me know the solution
i am also facing the same issue.......Sanjay, plz let me know how you resolved the issue.
Hi,
Help me please just me and that happens to me the mistakes my God.... I had the original ROM version coming with my diamond2, put the upgrading and went well until the moment he arrived at 9% and restart the pda, re-install I think is normal, however the installation continued until k stopped in 18% and after a long time gave a notice of error (262) made the recovery as recommended and continues to give error ....
I do help me please
This just happened to me too
My phone was hardspl´d
It stuck at 18%, but no error message so far. Did you unplug your phone?
Read this:
http://forum.xda-developers.com/showthread.php?t=425913
I'm not sure. Have you flashed other roms before? Perhaps you have a bad download. I know the servers are overloaded from all of us geeks sucking down the WM6.5 rom... perhaps its bad.
What I normally do is put the phone in bootloader mode first by holding VolDown, while resetting the phone. This will give windows time to install the proper drivers and get situated. Once done, try flashing again.
I think 262 is a connection error. Probably driver related since you said you ran your stock rom. But check your cable. Make sure its secure and reliable. Next try another USB slot. If nothing else try a different computer... sometimes PCs just will not cooperate.
Thank you very much fighter, will try that.
I had Official 6.1 Asia WWE installed, HARDSPLed. Tried to upgrade to 6.5 on my computer and my laptop, nothing worked. Both stops at 9%, disconnects, comes back and stucks at 18% again. Had to go back to 6.1, this time it worked to bring phone to life.
My phone was bought in Taiwan.
Guess I am out of luck
I think the best way to upgrade is as follows:
1. Run the RUU_Topaz_S_HTC_WWE_2.16.405.4_Radio_Sign_Topaz_61.44tc.25.32_4.49.25.17_Ship.exe on your PC/laptop to extract and get the RUU-signed.nbh.
2. Copy the RUU-signed.nbh to topaz SD card and rename to topaimg.nbh
3. Upgrade new ROM from SD card.
I had the same 262 error as well, screen went blank for a second at 9% and finally freezez at 18% with the error message. Heres what you need to do:
Update your HardSPL to 1.83
Flash 6.5 again
????
Profit!
Hello,
already did everything you say and nothing. I liked to tell me where I can get the former Rom wm6.1 because meeting.
help me please
duongla said:
I think the best way to upgrade is as follows:
1. Run the RUU_Topaz_S_HTC_WWE_2.16.405.4_Radio_Sign_Topaz_61.44tc.25.32_4.49.25.17_Ship.exe on your PC/laptop to extract and get the RUU-signed.nbh.
2. Copy the RUU-signed.nbh to topaz SD card and rename to topaimg.nbh
3. Upgrade new ROM from SD card.
Click to expand...
Click to collapse
Would you be so kind as to enlighten me/us on how to extract the nbh file from the executable file.
Thanks
player911 said:
I'm not sure. Have you flashed other roms before? Perhaps you have a bad download. I know the servers are overloaded from all of us geeks sucking down the WM6.5 rom... perhaps its bad.
What I normally do is put the phone in bootloader mode first by holding VolDown, while resetting the phone. This will give windows time to install the proper drivers and get situated. Once done, try flashing again.
I think 262 is a connection error. Probably driver related since you said you ran your stock rom. But check your cable. Make sure its secure and reliable. Next try another USB slot. If nothing else try a different computer... sometimes PCs just will not cooperate.
Click to expand...
Click to collapse
How can u exit bootloader screen? Only by removing the battery or...?
Thanks!
I do not have with me the adapter card to do this
There is also a problem is that the pda now I do not go the menu with the three colors blue, green and red, until I have done a hardreset and nothing ....
at least I no longer ask the solution with the ROM 6.5 we only have as I had before ... and wanted my pda to work help me please
Little history for my friends with same problem here:
1. Bought Diamond in Taiwan with Chinese;
2. HARDSPL 1.33;
3. Install Asia WWE 6.1 ROM;
4. Try update Official WWE 6.5 ROM, no luck, remove battery and put back;
5. Reinstall Asia WWE 6.1 ROM, everything back to normal;
6. Update HARDSPL 1.83; Ask brother to donate
7. Install Duttys ROM or Official ROM works too
Hello,
I already installed the previous ROM with the 6.1 and everything was normal.
I tried to install again the OFFICIAL ROM 6.5 and the problem remains back to the error at 9% and 18% for the progress bar giving an error (262).
not understand some things as:
6. Update HARDSPL 1.83; Ask brother to donate
7. Install Duttys ROM or Official ROM works too
is there any solution?
can help me
Sorry:
1. install Hard-SPL 1.83.OliNex (http://forum.xda-developers.com/showthread.php?t=520312)
2. install 6.5 ROM or Cooked Rom.
It resets 9% again in Official ROM, but reconnects and go to 100% (no stop 18% again).
Dutty ROM no stop at 9% or 18%.
problem solved
thanks for the great help amazing
thank you very much
hello
the memory card is not me out with the official wm 6.5 ROM
what can I do to boot the card?? I have a diamond2
ah no problem of card pk started the card with the adapter to the PC and read it perfectly.
pesquisar
AntonyWatson said:
Would you be so kind as to enlighten me/us on how to extract the nbh file from the executable file.
Thanks
Click to expand...
Click to collapse
When you run the RUU, the RUU-signed.nbh will be extract temporarily to a folder in driver C:
(For me: C:\Users\Duongla\AppData\Local\Temp\pft51D9.tmp)
Just do a search and you'll find it.
And remember to HSPL to 1.83.
i have the same problem too
hello
i have a diamond 2
ihave olinex 1.83 from here http://forum.xda-developers.com/showthread.php?t=520312 and i can not install ANY wm6.5 rom!!! on the other hand EVERY 6.1 rom i have trie (5 different greek and english) work perfect?!?!??
any suggestions?
thanks
i had the same issue
i was running 6.1 (stock rom) which was hard spl'd
i had the same error kept going to 262 and haviong to be recovered
so i re hard spl'd with the latest one, and it worked fine after that,
Hi
I just bought a used Diamond 2 and wanted to update it to 6.5.
But when i try it stops for at 9% and then looses connection with the PC but recovers and continues to 18% then it stops and the RUU wants to recover the installation, that resulted in the same error.
Luckely I tried the offical 6.1 installation, and that installd OK so my phone is OK.
But why can´t I install 6.5?
I checked with the guy i bought it from, and he said it has been flashed before with a dutty or tom´s rom.
Can this be why it wont load?
I check the bootloader screen (thanks to Drag-On guide) and i says SPL-1.33. OliNex MicroP-Topaz (LED) v10
Do I need 1.83 to install offical 6.5?
I am using swedish rom since I am swedish.
Can anyone help me?
/ Bidde
Try hard spl 1.83, then try re-flashing your 6.5
If it still won't flash, try a different rom. Download a cooked rom, Tess 4.0 for instance, and see if you can flash it. If you can, there is probably an error with the original rom. Tess is close to stock anyway, but faster and better
He he!
It worked! Thanks alot!
So now when I have done that, I will try to install a rom.
/ Bidde
yeah try hard spl 1.83 1st and then u'll be able to flash wm 6.5.
that's the only wayt to do it, otherwise it'll remain stuck at 18% everytime u try to flash the new rom
i have same problem now.
Please, where did you find offical 6.1 installation?
Could you pm link please.
I found on the http://wiki.xda-developers.com/index.php?pagename=Topaz_ROMs_Shipped my previosly ROM and recovered phone
Uh
The 6.1 I just downloaded it from the www.htc.com site.
Under the support you will find youre phone
exactly likeme ,, try to remove memory card
Hey all,
Maybe someone can help me out.
Two weeks ago i installed andoid on my HTC HD2.
I used HPSL, radio 2.15.50.14, MAGLDR112 and NexusHD2-Gingerbread_V2.1_NAND. A few days ago, without any reason i got a white bootscreen and i still have it
What a did so far:
* New HSPL3, but the radio didn't connected anymore, error 270.
* A new MAGLDR, i reached 100% in a blink, but then an error 270.
* Using a SD with the original leoimg, i get a (00018003 radio fail) error after a few % and the update failed.
* task29, but again no connection. (after 5 min error 262)
* new USB drivers installed for windows 7 and i also tried it on an windows Xp computer.
So far i only reached my 4 colored screen with:
PB81100 HX-BC
SPL-2.08. HSPL 8G XE
0x05
CotullaHSPL 0x30
* The original rom was RUU_Leo_S_HTC_NLD_3.14.404.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
Last question, how can i check that the batttery is stil oke for flashing.
Anyone who has a clue what to do?
Thanks in advance.
greetz!
Rob
Mate, I think you´ve done everything. HSPL and Radio ROM versions correct etc.
Since I see more and more people reporting similar problems like you, I get the feeling that some Android builds might have some strange effects on Radio ROMs.
There are too many people with SPL and Radio ROM problems, eg. stuck in bootloader or at the white startup screen.
This didn´t happen at this pace before Android NAND.
Only 1 question though:
Did you try to flash the original ROM using RUU.exe, SSPL or LeuCustomRUU via USB, without having the SIM and the SD card inserted? In rare cases, either one or both were trouble makers...
EDIT: Second question:
What kind of SD card did you try? Bigger cards seem more problematic, too.
I used a 2 gb micro SD card to go back to the original Rom.
I didn't tried to go back to original ROM using USB, because of the connecting problems. So that i'm gonna do now. Any suggestions which to use best?
After your post i tried to the flash with (and without) the formatted sd and the simcard, unfortunatelly i didn't work.
For last your question i can say that connect your phone to PC when it is off. Then keep down "volume down" button and switch on your phone. You get 4 colored screen. On bottom you can see USB word. Let phone for minimum 1h. And you get more 50% charged battery.
After hour you can flash back to original rom or to MAGLDR and forward normally flash android nand. You dont need disconnect or switch off before flash your phone.
Hope helps.
@tictac0566
Thanks for the options!
I tried the options mentioned in question 1, the problem is the connection USB/Radio. SSPL seems to work, but after 1% again connection error.
After a few test it must be the radio.
I tried to flash only a new radio using LEOIMG, after 99% i get the same error as LEOIMG an original Rom (00018003 radio fail)
With HPSL3_PKG i also can't go back to SPL 2.08.000.
So the problem must be there.
Anyone has an idea?? Can i use another radio? If yes, than which?
Thanks!
Still no solution
Tried many things, still the radio is not working.
It could be also HPSL3, because i can't go back to spl 2.08 (or any other (h)spl with the app.
Anyone has an idea??
Just trying to help here, but have you tried doing everything from the start?
task29 and everything else?
Hey i seem to have the same problem as you except my white screen wasnt after a flash, it just randomly went white one day and wouldnt boot.
I have tried MTTY, i can connect via usb but after formatting via MTTY and then attempting to flash a new rom (ship and custom) it just stays on 0% and doesnt do anything else.
Sorry to hijack thread just thought whilst people are looking they can help me too
CrAzYiaN said:
Just trying to help here, but have you tried doing everything from the start?
task29 and everything else?
Click to expand...
Click to collapse
Yes i did, this thread is official mine
It must be the radio or else HSPL3_PKG.
Do you have some options??
Thanks in advance!
tomar5e said:
Hey i seem to have the same problem as you except my white screen wasnt after a flash, it just randomly went white one day and wouldnt boot.
I have tried MTTY, i can connect via usb but after formatting via MTTY and then attempting to flash a new rom (ship and custom) it just stays on 0% and doesnt do anything else.
Sorry to hijack thread just thought whilst people are looking they can help me too
Click to expand...
Click to collapse
Can you go into bootloader? If you can then your problem can be solved. The problem you are having might have been because you unintentionaly installed or uninstalled a programm and that corrupted your rom.
To both of you. Try to flash using the leoimg.nbh step. If it doesn't work then the rom you used is not compactible with your device, try another till you find one that will work with your device. I know it is tiring to do something like that, here a tip from me, the rom you are expected to use in this process must be in the native language of your phone or else it will not work. You can't just use any stockrom to do it. I hope it helps.
Abdul9. said:
Can you go into bootloader? If you can then your problem can be solved. The problem you are having might have been because you unintentionaly installed or uninstalled a programm and that corrupted your rom.
To both of you. Try to flash using the leoimg.nbh step. If it doesn't work then the rom you used is not compactible with your device, try another till you find one that will work with your device. I know it is tiring to do something like that, here a tip from me, the rom you are expected to use in this process must be in the native language of your phone or else it will not work. You can't just use any stockrom to do it. I hope it helps.
Click to expand...
Click to collapse
Thanks for the advice, but all the roms i tried i got a radio fail during flashing with leoimg.nbbh.
Maybe your HSPL is faulty ? Did you try to re-HSPL your device using HSPL.exe ?
kawazaki said:
Maybe your HSPL is faulty ? Did you try to re-HSPL your device using HSPL.exe ?
Click to expand...
Click to collapse
Yes i tried, but mine HD2 stays on SPL-2.08 HPSL.
I used HSPL3_PKG and HSPL2 in different but still SPL-2.08 HSPL.
Maybe there's where my problems are, but i als can be an corrupt radio.
Anyone an other way to back to SPL 2.08.000 or how to fix the radio?
Then your best bet is to flash with a goldcard
Abdul9. said:
Can you go into bootloader? If you can then your problem can be solved. The problem you are having might have been because you unintentionaly installed or uninstalled a programm and that corrupted your rom.
To both of you. Try to flash using the leoimg.nbh step. If it doesn't work then the rom you used is not compactible with your device, try another till you find one that will work with your device. I know it is tiring to do something like that, here a tip from me, the rom you are expected to use in this process must be in the native language of your phone or else it will not work. You can't just use any stockrom to do it. I hope it helps.
Click to expand...
Click to collapse
Yes i can get into bootloader. I have tried using MTTY task 29 to format the device then i searched on the HTC site for a compatible ROM. Turns out the only one that doesnt give a negative response when i type in my serial number is the ROM from Taiwan. Tried flashing that using the SD card method and the USB method. Sd card method hangs at 0% and i get a connection error in USB method. I have also tried the latest ROM from Dutty.
If a ROM is not compatible how do you know? Does it hang at 0% or does it finish loading and then wont boot from there.
I have even tried flashing just a radio with the same results.
kawazaki said:
Maybe your HSPL is faulty ? Did you try to re-HSPL your device using HSPL.exe ?
Click to expand...
Click to collapse
Yes i tried all different types of HSPL and even SSPL. From the bootloader screen i run the .exe from the computer and it goes through and says 'operation finished successfully'
But when i get back to the bootloader it still says the same HSPL, which is 1.66
Also to note when i power on the device i can hear a small 'click' from it. Could be much worse and be a hardware problem?
Still no solution.
Oke guys, thanks for answering my threat so far!
Still trying to get my HTC back to life.
Is it possible that my problem is in HSPL? (see attachments)
After the white screen i tried to reinstall HPSL 2, 3 and 1, but during the instal my HTC reboot (without the signal "We Hacked It"
I also tried different SD card for LEOIMG, still radio fail 00018003.
One thing i didn't tried is using a goldcard, i downloaded the app but i need a working HTC HD2 to make the card.
Anyone?
No you don't, there you go :
http://forum.xda-developers.com/showthread.php?t=874304
Goldcard is the old method to install a custom rom way before HSPL became popular
so if HSPL don't work then Goldcard wont as well but hey you can still try
I think its more of a hardware problem now since all attempts for software repair is not successful. I had the same situation as yours, white screen then radio fail, tried all solutions but still no luck
sameeeeee
i have the same problem 100%
i already try all these solution and no one is worked
however, some one told me that maybe the problem with the Flash memory of my HD2 because he already try to solve / or already solve such problem "but unfortunately he lost the tools he was used"
this tools is can check the memory and told which memory chunk is corrupted
please if any one know this tools or had it please posted it on.....
That app should be Task 29.
hello
I need a rom of windows mobile 6.5 it was in english and it seemed like one of these
http://forum.xda-developers.com/showthread.php?t=801481 here but at the button of home had one andorid logo not home it had 9slides like andorid do but i cant find it because flashed the rom withot making a back up does any one where to find it.
it had some extras like i could set musicplayer on the first screen,basicly i could set every thing on the desktop. can anyone help me?
I'm not certain, if you are looking for a custom ROM or just Cookies Home Tab CHT , which mainly is the tool to do all the setup, you mentioned.
Greets
yes i think that was a costum rom couse i bought the phone like that.. but now ill try to add this app..thank you
Or you can install nsourm's beautifull rom with CHT included from here
By the way, I'm using nsourm's custom ROM too
Im trying to install one of these roms but it can not be installed. i tryed from sd card too but it says loading...
and i cant install cht too and cookies because the clock and others become to big..
Can you describe the error a little more detailed? I was able to install nsourm's ROM without problems. Did you see the tri-colored screen already?
I tryed to install nsourm_rom_0409.nbh and all of them and cant be installed, i can install roms from shipped roms and those can be installed but this can not...it stuck at 0% and the rom from http://www.filefactory.com/ can not be downloaded Ive downloaded a old one .. couse this says: "All free download slots are in use. You can download this file immediately by upgrading to FileFactory Premium. Otherwise, please feel free to try again shortly. "
You gotta try multiple times, until you get a slot to download a newer version. I tried at least for half a day
The flashing itself worked, but I remember it took more than 10 minutes to finish.
Did I understood right, that you have flashed custom ROM's before?
Greets
I've downloaded the rom and when i try to install it gives me error 262 and it does not continues to be installed stays at 0% ..yes I'have flashed before... but i did not made a backup of that rom
thank you!
so can anyone help me how to put the rom couse it cant be upgraded
Just to be sure i understood your problem: Did you used SSPL with a custom ROM and it didn't work ? What OS do you have on PC ?
yes that is right...im using windows 7 ultimate .It can not be upgradet stays at 0% and then gives an error :S
EROR 262 you can solve this way
- Make shure battery is over 50%
- Soft-reset the device - Don't Skip This Step !
- If is on your PC installed Software-Firewall, Deactivate it (temporery,just to be sure, Reactivate FW later)
- Use orignal USB Kable. (usb data link cable)
- Right click on the RUU.EXE and click on Run as Administrator
- make sure, you choose ActiveSync profile upon connecting the phone to PC
- ActiveSync should be set up completely and Sync connections with Win7 PC should be working without problems before starting with a new ROM
okay thank you guys