[Voda UK 1.43->1.66] Wi-Fi No More - HD2 General

Hi folks,
Upgraded to v.1.66 a while back (I'm on Voda UK) and can no longer connect to my Wi-Fi network. Done reset to factory defaults twice. Immediately after reset and during initial setup HD2 will successfully connect to Wi-Fi but that's about it. Any other attempt to connect will fail.
Wi-Fi is available (2-4 bars depending what part of the house I'm in).
Overall, every time I tap on the wi-fi it will look like HD2 is trying to connect but with no result whatsoever. Like trying and dropping straight away.
Tried with no seeming result:
- setting static IP on DHD Broadcom adapter
- changing Data Encryption (AES to TKIP and back)
Wi-Fi worked b4 the upgrade to 1.66 (from 1.43). Didn't have to change any of those settings above.
Logs on Wi-Fi router won't register any attempts to connect. My pure guess is that signal/connection/whatever drops b4 any IP address will assign.
I know that not a lot of information but that's what I have gathered so far.
Ideas? Thanks.

look at all other adapters and set them to dhcp... no problems with wifi on 1.66. make sure your router is configured to allow new wifi connections...

Replaced router today. Seem to have sorted the issue. Will keep my eye on it.

Related

WIFI and GPRS not working

I'm really racking my brain on this one. I would greatly appreciate any ideas, as I've long run out of them.
---Intro---
I have a one week old Wizard (Cingular 8125 variant). It has one of the latest roms with AKU2 on it. Using Registry Wizard, I selected the option to add wireless G compatibility at some point in time. Wireless initially worked after setting my phone and router up per a tutorial on a popular Axim users forum. A day or two later I went to use WIFI and I get nothing. GPRS/EDGE initially worked also, but at the same time it stopped working. I've spent countless hours since trying everything I possibly can to get WIFI to work.
---The problem---
I am not able to connect to the wireless router. My Wizard sits on "connecting" forever then maybe 5 mins later it says unable to obtain an IP address. When I look at the status, it says 0.0.0.0 for the IP address the whole time it says connecting. Since the problem started, I have yet to actually connect using any settings. The first day I configured the wireless it worked perfectly, with WAP encryption and all.
---Some of what I have tried---
On my US Robotics wireless router I've turned mac filtering and all security settings off, making an open network. I removed the WAP setting for the connection on the Wizard as well. I've tried all the suggestions I can find on any WM 5 and 2003se related forums to no avail. I've tried all the various combinations of limiting to B/G only or mixed, using work/internet settings, and deleting WIFI connections and creating new ones. I don't have a proxy setting in any of my connections. The whole time my battery usage is set to the highest (performance) setting and I'm right next to the wireless router. I've tried turning off all proprietary speed enhancement options. I even installed a program (Pocket DHCP) recommended by Axim PPC users to figure out why I'm not receiving an IP. Since I'm not really a DHCP wiz, I can't tell from the results what is causing this.
I'd be greatful if anyone can help me with figuring this one out. Thanks in advance!
maybe a dumb question, but...the wireless part of the router is working fine? did u tryed with a laptop or pc?
did u tried a hard reset?
That's actually a great question. I did connect fine the first day I configured the wireless and made no changes from then until it stopped working, so I'm just assuming that the router is working properly. Unfortunately I don't have access to any other wireless device/laptop to test it with.
I'm getting ready to do a hard reset right now. I was really wanting to avoid this but I think I have no other option. Hopefully this will fix whatever setting was messed up. I have a slight hunch that the registry change for allowing G access was the cause of the problems.
maybe i missed this in the original post, but have you tried making your device use static ip's on the lan instead of dhcp?
Shogunmark:
I didn't try static IP's for two reasons. 1. Firstly I couldn't figure out how to set this up. 2. I don't want to have to fiddle with removing the static IP when I'm away from home trying to use a different wifi hotspot. I would like it to be seamless and just connect when I turn wifi on near any unsecured network (other than the usual pressing OK to connect).
STATUS UPDATE:
I did a hard reset and directly after this I tried to connect to my open network. Amazingly GPRS/EDGE now works, but WIFI still does not. Then I did a factory reset on my USR router then changed the settings back to how it was just set before. Now, I'm connecting. This doesn't make any sense since the settings are the same now but it's working, maybe theres a glitch with the router that this fixed. This small progress seams like a miracle.
Now that I can connect to WI-FI, I have a new problem. When I try to load pages in internet explorer, it says page not found or whatever the standard error message is. I'm so close I can smell it. There must be some setting that needs to be changed on my Wizard.
SUCCESS
I report that I am now absolutely delighted with network connection on my Wizard. After hard reseting the phone and the router, now I can connect to both WIFI and GPRS. Not only that... but also PIE will choose WIFI if I'm connected to a wireless router, otherwise it will default to GPRS/EDGE without any interaction from me. This stuff is really awesome when it works. It is difficult to setup correctly though.
somehow wifi routers r not 100% reliable, every now and then i need to reset my linksys or i cant get ip as in your case...but with a normal reset is enough in my case...
That's good to know. Maybe I didn't even need to hard reset my Wizard, just the router. Now I know to start with the router because it's much easier to reconfigure. This is the first time that I've implemented WIFI on my own network. What happens if a public WIFI spot won't give you an IP anymore? Surely you just can't go and reset it. Granted it's not nearly as old as Ethernet, WIFI has been out for long enough that you think they would have these major kinks worked out.
Nicnatros said:
... but also PIE will choose WIFI if I'm connected to a wireless router, otherwise it will default to GPRS/EDGE without any interaction from me.
Click to expand...
Click to collapse
How did you manage this? I have been struggling for ages to set things up this way. Can you post your settings from settings>connections>connections>advanced>select networks. Also settings>connections>network cards.
I would like to be able to just turn on wlan from comm manager and use wifi to surf and connect to my wireless lan, but if no wifi available to default to my T-mobile gprs connection for surfing. Currently having to manually change the settings "Programs that automatically connect to the Internet should connect using" My Work Network or Tmobile gprs each time I want to use either.
What I want is the option
if wifi available
use wifi
else use gprs
Well my friends and I were like sitting around drinking foo-foo drinks and I just like stumbled upon the answer. Just kidding, it's fun to play the role of your avatar, especially mine.
Settings, Connections tab, Network Cards, Network Adapters tab: My network card connects to Internet
Settings, Connections tab, Connections, Advanced tab, Select Networks: Set first one to My work network. Set second one to MediaNet (or your gprs/edge/etc connection profile).
Now with those set, edit the My Work Network profile and make sure that under the proxy tab check connects to the internet option, uncheck the proxy option. Now edit your MediaNet (or other carrier data plan) and make sure that this contains all options for your carrier like proxy, modem, etc. If you are a Cingular user, go here to verify all settings for medianet. (Note that you will ignore the beginning couple steps when they say to place medianet first in the "select networks" settings. Start after step 6. Also they used the CingularGPRS connection profile instead of the MediaNet one) http://www.pocketpcaddict.com/forum...ular-8125-windows-mobile-5-phone-edition.html
When you connect to your WIFI router first and it asks you if it's work or internet, always select internet. If you are not sure what it's set at, go out of range or unplug your router. Go into network cards and find your router SID, click and hold on it and select remove. Then when you try to connect to your WIFI again it will prompt you for this, make sure you use internet setting.
Now if you have done everything correctly, Internet Explorer will use WIFI when it's turned on and you get a connection. All other times it will default to GPRS/EDGE. I can go from one to the other back and forth without changing any settings, only enabling and disabling WIFI in the comm manager.
Trashman said:
somehow wifi routers r not 100% reliable, every now and then i need to reset my linksys or i cant get ip as in your case...but with a normal reset is enough in my case...
Click to expand...
Click to collapse
Linksys WRT54Gx? if yes look into dd-wrt . stable and has a lot of features . other hardware is supported as well just check on their webby.
yaboc said:
Linksys WRT54Gx? if yes look into dd-wrt . stable and has a lot of features . other hardware is supported as well just check on their webby.
Click to expand...
Click to collapse
I have read many many many posts about people having issues with the wizard and that exact router... I personally would stay away from linksys.. i work in a field that deal with 3rd party routers and such, anytime an end user has a linksys i can usually prove 90% of the time that its the culprit (80% of the time powercycling it does the trick)
Nicnatros said:
Go into network cards and find your router SID, click and hold on it and select remove. Then when you try to connect to your WIFI again it will prompt you for this, make sure you use internet setting.
Now if you have done everything correctly, Internet Explorer will use WIFI when it's turned on and you get a connection. All other times it will default to GPRS/EDGE. I can go from one to the other back and forth without changing any settings, only enabling and disabling WIFI in the comm manager.
Click to expand...
Click to collapse
This seemed to do the trick for me.
I am sure that I had tried all possible combinations previously but what the hell, it is working exactly how I want now.
Thank you

Can't connect using WiFi on my MDA Vario 2

Hi there,
My WIFI connection worked fine with a Belkin router I had. After upgrading to a 'Netgear Next Wireless ADLS2+ Modem (router)', I cant seem to lock onto the router.
I type in the WEP Key, but then the arrows of the indicator on the top continue moving showing that no connection has been established.
I am not as good as I would like to be with networking, so I need easy step-by-step advise with how I can set up a connection.
Please help.
Many thanks.
Over 60 views, and no reply!
Anyone?
well since it worked before maybe the question should be posted in the Netgear forum
i would at first upgrade the firmware of the router if possible
Hi
I've not long had my Vario 2 and I had the same problem, it just refused to connect. I looked in the active Station List in my routers config page but there was no sign of my vario's MAC. I thought maybe the wifi was busted so I took it to work and connected fine. Back to my router then, eventually it appeared in the station list but was being reported as failing the WPA authentication. I must have put that key in I don't know how many times before it finally let me in. I don't know how it happenned but I just sat there repeatedly entering the key and refreshing router config screen.
I suggest you try connecting to another wifi network to test your device. Try connecting to yours with security off, then switch it back on.
I just had to seemingly bully my router into letting me connect, but after some time (several sessions over a few days) it did.

How I solved Wifi problem

Lately I have been reading many post related to Wifi problems in the HD. I had the same. Even I was very near my router I couldn't connect to the net and the signal was very weak.
So I entered my router configuration and I found a solution.
Before, for security options I had: WPA-PSK [TKIP] then I changed to WPA2-PSK [AES] (of course you also have to change your HD connection configuratoin), and now it works great¡¡¡¡
Now I have all the bars for the signal and I can connect very easily.
Hope it works for other people
I have a similar WiFi connectivity problem, but after reading of the poor service provided by most vendors and HTC itself, I will try to gather some more experience with the problem before I contact HTC or my vendor, and hopefully find a solution. Bellow is my experience so far:
I own an HTC Touch HD since January and have a similar problem, only it surfaced last week. Before I had only used the WiFi connectivity briefly. The problems started after I installed an AP on my house expressively for the new PDA. The node is fully open and set to B/G/N protocols.
After a couple days of medium (couple hours per day) use the WiFi connection suddenly quit, the device would try to connect (the top bar showing the WiFi connection animation continuously) and after a few moments gave up with a dialog box stating the current network settings were wrong (even thou they worked fine a few hours earlier).
I tried several hot and cold resets, but only solved the problem after flashing a new ROM; even then the same symptoms reappeared after a couple of days of regular use. Again no re-setting would cure the problem, and now not even flashing the ROM again would work. Nonetheless, some hours latter the WiFi would connect perfectly with the same nodes it refused to before, and in very short time.
I have witnessed this cycle twice and have yet not been able to find a trigger for it, but will keep my eyes open for any tell tale signs, and post any findings here.
I could add to the above mentioned problems.
i got a new hd just few days back.
The wifi worked great. But now it doesnt.
I have disabled wifi, so can start it whenever i require.
I click on wifi button to enable it.
Then open opera, try any website.
it will open fine.
For instance say my email at gmail.com
Now after that if i try to open anysites or even continue with my mail, it shows error saying connection not available.
One of the workaround is to go back to toggele wifi off and switched it on.
Not sure if anyone faces a similar issue.
I's been about a week since my last post and I have already witnessed a couple of cycles of WiFi connecting perfectly and then not connecting at all.
No matter the settings I try after it decides not to connect, it won't. Even to nodes it had connected perfectly and fast jus minutes before.
I thought re-flashing might help but so far has proven ineffective. Once I thought some part of the non-volitile memory was causing the problem since after I cleared the memory I could connect for a while.
Any thoughts anyone?
Same problems here.
For the last hour I have been reading 10ths of threads here concerning WiFi problems.
My HD's WiFi worked fine on my home and outside for about 2 months. Now it doesn't. It reports connection, but no program can use the internet. At best, it seems to be able to exchange some Kbytes the for just a few seconds after a connection is established. Then nothing. Connected but unusable.
Tried everything Internet/My Work/My ISP, WAP enabled/disabled, soft/hard reset, everything.
When connected through ActiveSync everything works fine, all programs see internet.
Has anybody taken their HD to the service? Has any HTC service worldwide identified the problem as hardware and solved it by replacing something?
miskasp said:
Lately I have been reading many post related to Wifi problems in the HD. I had the same. Even I was very near my router I couldn't connect to the net and the signal was very weak.
So I entered my router configuration and I found a solution.
Before, for security options I had: WPA-PSK [TKIP] then I changed to WPA2-PSK [AES] (of course you also have to change your HD connection configuratoin), and now it works great¡¡¡¡
Now I have all the bars for the signal and I can connect very easily.
Hope it works for other people
Click to expand...
Click to collapse
I have just encountered a similar problem, but already used wpa/wpa2 with aes. Have tried a hard reset with no joy. My old HTC Touch has no probs connecting via wifi nor does my laptop so I would surmise that the prob is with the HD and not the router.
I am going to try flashing with the latest version of Duttys 6.1 rom and see what gives.
Edit: Tried flashing with new rom with no success. Take a look at this post.
http://forum.xda-developers.com/showpost.php?p=3769339&postcount=7
There are a couple of files to download but i only used the second ie this one.
http://forum.xda-developers.com/showpost.php?p=1363759&postcount=2
Now no problems and can connect via wifi no probs, ip address assigned by dhcp.
Try to go into WiFi settings and move the power slider to max performance. I need to do it here to access my router. This happened also with my HTC TyTN II, with any recent radio firmware. The original WM 6.0 ROM and it's radio work fine in low power mode, but the new ones appear connected but are always at 1 Mbps and there's no traffic until you move the slider to performance mode.
You go into WiFi settings and you configure manual IP and DNS so as router.
DNS is important.
Whit manual configuration, Wifi work always.
(sorry for my english)
Dubh Llas said:
There are a couple of files to download but i only used the second ie this one.
http://forum.xda-developers.com/showpost.php?p=1363759&postcount=2
Now no problems and can connect via wifi no probs, ip address assigned by dhcp.
Click to expand...
Click to collapse
Yeah, but what if I 'm not Orange-UK (let alone UK) ?
vcespon said:
Try to go into WiFi settings and move the power slider to max performance.
Click to expand...
Click to collapse
1st thing I did. Problem still there.
campotino said:
You go into WiFi settings and you configure manual IP and DNS so as router.
DNS is important.
Whit manual configuration, Wifi work always.
Click to expand...
Click to collapse
This is not a solution. I didn 't buy the device to be able to connect to my home WiFi only. What about public hotspots? Or hotels? Or whatever outside your home?

Wifi will not connect - HTC-8900

My phone will not connect to any wifi hotspots. At home I have gone through my router insuring there is the absolute least authentication: no key, no certificates, no filters. I have tried open routers elsewhere like at the local library and no luck.
When attempting to connect to a router the connection goes form available to connecting and back to available with no error message or change of any kind. My phone had worked previously but after sitting around for a few weeks it will now not connect to these routers it used to have no problem connecting to. I have done a hard reset once with AT&Ts bloatware (Tilt) once without as it is now and that has not helped.
I am using WM 6.0 (CE OS 5.2.1622 Build 18128.0.4.4). I have chosen for it to connect to the internet not work, I have set it for best performance not best battery and all other settings are default.
When I go through Wireless LAN in the settings and hit change network then try to connect and quickly hit ok to go back, the SSID, and BSSID come up for about 5 seconds and the signal quality is almost full strength. Mode is Infrastructure and Tx/Rx Rate never show any values. The same channel as my router is set (11).
I am at a loss for anything else to try. Any ideas would be appreciated. The only thing that was different from the last time it was used is that for the first time every during that time period the 3G network was used for internet but I would image even if this did change anything a hard reset would have reverted it as it worked fine after a previous hard reset months ago.

Can't connect to WiFi using Touch HD

Hi everyone.
First off, I know there are a million and one other threads.. believe me.. I have searched!
Basically my phone won't connect to my network. It was working fine earlier today. I've tried changing all the security settings in my router (turning off encryption for example). I've tried soft resetting and hard resetting the phone.
Nothing seems to be working. It finds the network fine, but it just says 'Connecting' then goes to 'Available' but it won't use the wifi connection.
Any ideas?
Thanks!
Have you tried connecting your device using a friends wifi router to see if this connect you
Nope. I forgot to add that I will try connecting to work's WiFi tomorrow!
Anything to try in the mean time?
Try these:
1) disable frame bursting
2) disable big packets and other methods of wifi speeding
3) force 11b
4) use WPA-PSK TKIP only
5) check if you have MAC or other access filtering
than let us know
miland said:
Try these:
1) disable frame bursting
2) disable big packets and other methods of wifi speeding
3) force 11b
4) use WPA-PSK TKIP only
5) check if you have MAC or other access filtering
than let us know
Click to expand...
Click to collapse
1) Can't see any settings under my router.
2) Tried disabling gnitro (Belkin router), no difference.
3) No difference
4) Already on that.
5) Turned off.
It's so odd. Works fine with an N95.
I don't think it's anything to do with my router because like I said it worked fine earlier on in the day then suddenly stopped. The router settings hadn't changed.
Edit: I've tried turning the router security off altogether also. I really don't feel it's an issue with my router.
Tested the phone at work. It works fine.. so I don't have a clue why it's not working at home? Surely the router can't be incompatible with the phone.. especially considering it worked at one point.
Very weird! I got fed up with my router so decided to restore the factory defaults and start from scratch.. worked straight away! So I restored the settings back to exactly how they were before (using a backup file I made).. and it worked!
Just posting incase it happens to anyone else anyway.
AltF4me said:
Very weird! I got fed up with my router so decided to restore the factory defaults and start from scratch.. worked straight away! So I restored the settings back to exactly how they were before (using a backup file I made).. and it worked!
Just posting incase it happens to anyone else anyway.
Click to expand...
Click to collapse
Maybe uve tried this already but could be the fact that your home internet access point is listed as Work rather than internet, used to have an issue with mine cause of that.
I also have this problem.
Reset did not help.
Listed as internet or work did not help in both cases.
Real weird!!
I've got the same problem, all of a sudden my hd won't connect to my router.
I can connect to open networks (wi-fi hotspots etc) so i know the wifi in the phone is working ok and my partners diamond can connect ok to my router, so the router is obviously ok.
Have reset the router as well and haven't changed any settings on the phone.
Don't understand!!!!
as other users point out within other threads, it seems that Blackstone has a problem connecting to wifi networks when WPA Authentification is enabled
try to disable it. it worked for me and soem other guys
good luck!
I could connect to my router fine using my laptop.. but I still had to reset my router to the factory settings before it worked again on my Touch HD.. then I could enable WPA and everything back again. So try that!
i thought i had a similiar problem, mine wouldnt connect to wifi, kept switching itself off. figured this is normal when its connected to usb. unplug usb and it turns back on!
I own an HTC Touch HD since January and have a similar problem, only it surfaced last week. Before I had only used the WiFi connectivity briefly. The problems started after I installed an AP on my house expressively for the new PDA. The node is fully open and set to B/G/N protocols.
After a couple days of medium (couple hours per day) use the WiFi connection suddenly quit, the device would try to connect (the top bar showing the WiFi connection animation continuously) and after a few moments gave up with a dialog box stating the current network settings were wrong (even thou they worked fine a few hours earlier).
I tried several hot and cold resets, but only solved the problem after flashing a new ROM; even then the same symptoms reappeared after a couple of days of regular use. Again no re-setting would cure the problem, and now not even flashing the ROM again would work. Nonetheless, some hours latter the WiFi would connect perfectly with the same nodes it refused to before, and in very short time.
I have witnessed this cycle twice and have yet not been able to find a trigger for it, but will keep my eyes open for any tell tale signs, and post any findings here.
Hi
I used to have problem using any secure wireless connection. Then I realized that you need a personal certificate to use secure wireless networks. It uses certificate to encrypt connection between access point. I have access to a windows certificate server so I created a personal certificate with private key and import it to my mobile. Now I can login to any secure wireless network.
A solution has been posted for data connection problems. Can be found here
This may help, may not. Let me know
Fallen Spartan said:
A solution has been posted for data connection problems. Can be found here
This may help, may not. Let me know
Click to expand...
Click to collapse
That solution doesn't seem to work for this problem.
Resetting the router does seem to work.
I don't get why resetting the router works.... other devices can still connect no problems before resetting, so it only seems to be aproblem with the hd.
It also sux when you are using a public router with this problem that you can't reset.
Connecting to Belkin router
Guys, I had the same problem as well. HTC touch HD used to connect to the router fine but after installing an update/upgrade it would pick the signal from the router but would not connect. (I was using WEP authentication at this time)
SOLUTION:
Go to belkin router configuration on the web.
Under security change the Securtiy Mode to WPA/WPA2-Personal(PSK)
Change authentication to WPA-PSK
Select Encryption to TKIP and enter your password.
GO to your HTC touch HD's WiFi setting and turn Wifi ON. Select your home network SSID and edit it using the information you used on the router i.e. WPA-PSK ; TKIP, enter your key/password and click next, next and finish.
Worked for me....hope it helps.
WIFI not connecting
That truly is extremly nasty.
I have the same issue - wifi found, correct password (WEP, WPA all settings) but no successful connection.
Took an old HTC 3xxx - runs immediately.
I can not reset the router - there are too many users, they will kill me then.
So I installed an Access point (Sparklan WX 7800A) to play with.
Notebooks (HP, MSI and ASUS) have successful internet access, also the old HTC 3xxx.
But still the HTC HD does not connect.
Tried "WIFI Monster" - shows the wifi, but does not connect.
(But it deletes all wifi entries easily - so you can set them up new)
Tried with NO security/password: same issue.
WEP, WPA (all kinds): no connection
There must be something to be changed in the registry - but I have no idea what & where.
Or is the wifi that useless ?????
Maybe someone can help
Ciao
Mike
I had the same problem. But the problem stopped when i connect my htc HD to my laptop and used activesync to connect to internet. After i disconnected it, open wifi and... works ok!!

Categories

Resources