Database Users

PC, WiFi, PPC, IP solution?

OK so after having problems connecting my XDA2s to my laptop via wifi to use it's ADSL connection, I began to realise it was a major issue for a lot of users.
Having covered almost all the threads here regarding PPC WiFi issues, I still am perplexed as to how the whole thing is successfully set up.
I concluded that it was virtually impossible; that the PC would not provide the PPC with an IP address so I would have to use some sort of application to manage the connection. However, yesterday for some reason only the omnipotent holy deities of the grandiose gods of WiFi would know, I had it working perfectly. For about 10 minutes, until I decided to disconnect to see if I could readily re-connect. My hopes were of course, dashed, and I have not had it working again since.
I have tried every combination of settings on both the laptop and the XDA to no avail, and have followed more threads and links than I can count on my fingers and toes. I've tried all the same settings I had when it was working (briefly) but still have no real success.
So basically, what's the deal with getting this damn thing working? Maybe what I need is a step by step idiot's guide on how to initially set up the wireless network on the laptop first, to make sure it has all the right settings? I'm using a Vaio running XP home (built in WiFi).
Has anyone completely resolved this problem yet? I would really like a solid, clean method of setting up the connection rather than stumbling through a million different combinations of settings and ending up with something hashed and unstable.
Many thanks for any help on this, I'm sure it's a tiresome subject for many.

......And as is always the case, as soon as you post about it you figure it out!
If anyone is still having trouble using their XDA2 to connect to a PC's ADSL via WiFi, ive got it figured!

RE: ive got it figured!
PLEASE HOW? I HAVE ALSO THE SAME PROBLEM HERE
THANKS

Me too. I have a XDA mini S.
I don't know what settings to put into the thing. I had it connected for a short while but when I went into internet explorer it started connecting to GPRS instead of WIFI to internet.
Clearly I haven't got a clue. The book is of no help either.
Any ideas?
Thanks

Think i'm connected to the internet. It doesm't seem to want a password although one is listed listed in the router. Just can't stop it going over GPRS instead of the wifi for intenet????

problem solved
Hi All
Ok heres what I did .
Connections
under my work network
set ,set up my proxy server to "this network connects to the Internet.
Then go to advanced
Under select networrks ,Network management,Set both to "my work network"
Network Card
Network adapters
"My network card connects to work
Then select the network card ie sandisk
tick Use specific ip address
type in 1 thats on your network ,It will connect but you wont be able to browse still
Then soft reboot
change from use ip adress to "server assigned ip address"
soft reboot
and bingo

WIFI and GPRS not working

I'm really racking my brain on this one. I would greatly appreciate any ideas, as I've long run out of them.
---Intro---
I have a one week old Wizard (Cingular 8125 variant). It has one of the latest roms with AKU2 on it. Using Registry Wizard, I selected the option to add wireless G compatibility at some point in time. Wireless initially worked after setting my phone and router up per a tutorial on a popular Axim users forum. A day or two later I went to use WIFI and I get nothing. GPRS/EDGE initially worked also, but at the same time it stopped working. I've spent countless hours since trying everything I possibly can to get WIFI to work.
---The problem---
I am not able to connect to the wireless router. My Wizard sits on "connecting" forever then maybe 5 mins later it says unable to obtain an IP address. When I look at the status, it says 0.0.0.0 for the IP address the whole time it says connecting. Since the problem started, I have yet to actually connect using any settings. The first day I configured the wireless it worked perfectly, with WAP encryption and all.
---Some of what I have tried---
On my US Robotics wireless router I've turned mac filtering and all security settings off, making an open network. I removed the WAP setting for the connection on the Wizard as well. I've tried all the suggestions I can find on any WM 5 and 2003se related forums to no avail. I've tried all the various combinations of limiting to B/G only or mixed, using work/internet settings, and deleting WIFI connections and creating new ones. I don't have a proxy setting in any of my connections. The whole time my battery usage is set to the highest (performance) setting and I'm right next to the wireless router. I've tried turning off all proprietary speed enhancement options. I even installed a program (Pocket DHCP) recommended by Axim PPC users to figure out why I'm not receiving an IP. Since I'm not really a DHCP wiz, I can't tell from the results what is causing this.
I'd be greatful if anyone can help me with figuring this one out. Thanks in advance!

maybe a dumb question, but...the wireless part of the router is working fine? did u tryed with a laptop or pc?
did u tried a hard reset?

That's actually a great question. I did connect fine the first day I configured the wireless and made no changes from then until it stopped working, so I'm just assuming that the router is working properly. Unfortunately I don't have access to any other wireless device/laptop to test it with.
I'm getting ready to do a hard reset right now. I was really wanting to avoid this but I think I have no other option. Hopefully this will fix whatever setting was messed up. I have a slight hunch that the registry change for allowing G access was the cause of the problems.

maybe i missed this in the original post, but have you tried making your device use static ip's on the lan instead of dhcp?

Shogunmark:
I didn't try static IP's for two reasons. 1. Firstly I couldn't figure out how to set this up. 2. I don't want to have to fiddle with removing the static IP when I'm away from home trying to use a different wifi hotspot. I would like it to be seamless and just connect when I turn wifi on near any unsecured network (other than the usual pressing OK to connect).
STATUS UPDATE:
I did a hard reset and directly after this I tried to connect to my open network. Amazingly GPRS/EDGE now works, but WIFI still does not. Then I did a factory reset on my USR router then changed the settings back to how it was just set before. Now, I'm connecting. This doesn't make any sense since the settings are the same now but it's working, maybe theres a glitch with the router that this fixed. This small progress seams like a miracle.
Now that I can connect to WI-FI, I have a new problem. When I try to load pages in internet explorer, it says page not found or whatever the standard error message is. I'm so close I can smell it. There must be some setting that needs to be changed on my Wizard.

SUCCESS
I report that I am now absolutely delighted with network connection on my Wizard. After hard reseting the phone and the router, now I can connect to both WIFI and GPRS. Not only that... but also PIE will choose WIFI if I'm connected to a wireless router, otherwise it will default to GPRS/EDGE without any interaction from me. This stuff is really awesome when it works. It is difficult to setup correctly though.

somehow wifi routers r not 100% reliable, every now and then i need to reset my linksys or i cant get ip as in your case...but with a normal reset is enough in my case...

That's good to know. Maybe I didn't even need to hard reset my Wizard, just the router. Now I know to start with the router because it's much easier to reconfigure. This is the first time that I've implemented WIFI on my own network. What happens if a public WIFI spot won't give you an IP anymore? Surely you just can't go and reset it. Granted it's not nearly as old as Ethernet, WIFI has been out for long enough that you think they would have these major kinks worked out.

Nicnatros said:
... but also PIE will choose WIFI if I'm connected to a wireless router, otherwise it will default to GPRS/EDGE without any interaction from me.
Click to expand...
Click to collapse
How did you manage this? I have been struggling for ages to set things up this way. Can you post your settings from settings>connections>connections>advanced>select networks. Also settings>connections>network cards.
I would like to be able to just turn on wlan from comm manager and use wifi to surf and connect to my wireless lan, but if no wifi available to default to my T-mobile gprs connection for surfing. Currently having to manually change the settings "Programs that automatically connect to the Internet should connect using" My Work Network or Tmobile gprs each time I want to use either.
What I want is the option
if wifi available
use wifi
else use gprs

Well my friends and I were like sitting around drinking foo-foo drinks and I just like stumbled upon the answer. Just kidding, it's fun to play the role of your avatar, especially mine.
Settings, Connections tab, Network Cards, Network Adapters tab: My network card connects to Internet
Settings, Connections tab, Connections, Advanced tab, Select Networks: Set first one to My work network. Set second one to MediaNet (or your gprs/edge/etc connection profile).
Now with those set, edit the My Work Network profile and make sure that under the proxy tab check connects to the internet option, uncheck the proxy option. Now edit your MediaNet (or other carrier data plan) and make sure that this contains all options for your carrier like proxy, modem, etc. If you are a Cingular user, go here to verify all settings for medianet. (Note that you will ignore the beginning couple steps when they say to place medianet first in the "select networks" settings. Start after step 6. Also they used the CingularGPRS connection profile instead of the MediaNet one) http://www.pocketpcaddict.com/forum...ular-8125-windows-mobile-5-phone-edition.html
When you connect to your WIFI router first and it asks you if it's work or internet, always select internet. If you are not sure what it's set at, go out of range or unplug your router. Go into network cards and find your router SID, click and hold on it and select remove. Then when you try to connect to your WIFI again it will prompt you for this, make sure you use internet setting.
Now if you have done everything correctly, Internet Explorer will use WIFI when it's turned on and you get a connection. All other times it will default to GPRS/EDGE. I can go from one to the other back and forth without changing any settings, only enabling and disabling WIFI in the comm manager.

Trashman said:
somehow wifi routers r not 100% reliable, every now and then i need to reset my linksys or i cant get ip as in your case...but with a normal reset is enough in my case...
Click to expand...
Click to collapse
Linksys WRT54Gx? if yes look into dd-wrt . stable and has a lot of features . other hardware is supported as well just check on their webby.

yaboc said:
Linksys WRT54Gx? if yes look into dd-wrt . stable and has a lot of features . other hardware is supported as well just check on their webby.
Click to expand...
Click to collapse
I have read many many many posts about people having issues with the wizard and that exact router... I personally would stay away from linksys.. i work in a field that deal with 3rd party routers and such, anytime an end user has a linksys i can usually prove 90% of the time that its the culprit (80% of the time powercycling it does the trick)

Nicnatros said:
Go into network cards and find your router SID, click and hold on it and select remove. Then when you try to connect to your WIFI again it will prompt you for this, make sure you use internet setting.
Now if you have done everything correctly, Internet Explorer will use WIFI when it's turned on and you get a connection. All other times it will default to GPRS/EDGE. I can go from one to the other back and forth without changing any settings, only enabling and disabling WIFI in the comm manager.
Click to expand...
Click to collapse
This seemed to do the trick for me.
I am sure that I had tried all possible combinations previously but what the hell, it is working exactly how I want now.
Thank you

Wi-Fi Doesn't Connect

Okay, I've searched, sifted through a boatload of possible threads relating to mine and still haven't found a resolution to my problem.
My Wi-Fi doesn't connect to my wi-fi router at home. My laptop connects perfectly fine without any hiccups. I've gotten the wi-fi to connect to our local Apple Store's wi-fi network to access the internet.
I double checked the password like a hundred times, disabled to proxy, and made sure the network is connecting to the internet and not on the my work settings.
I'm still using WM5 and not sure if it's an issue with the OS or not.
Please someone lend a helping hand. I've spent many hours researching this problem and still nothing.
Note: I did get it to connect only once when I first got last week and it didn't work again after I left the house. I've master reseted the damn thing over 5 times just to make sure.

1.Erase the settings for your home network out of your phone 2. Remove the security from your router and try connecting again
If that does not work hard reset the router again and try to connectthrough its default settings (make sure their are no saved wifi networks in your phone)

sprice82 said:
1.Erase the settings for your home network out of your phone 2. Remove the security from your router and try connecting again
If that does not work hard reset the router again and try to connectthrough its default settings (make sure their are no saved wifi networks in your phone)
Click to expand...
Click to collapse
I've tried your method. The first didn't work.
The second method worked. I had to hard reset my router and try again and it finally worked even with my password. I also master reset my phone prior to hard resetting my router.
Thanks for the info. Would you happen to know why it might have done that?

It might have bveen the security settings on the router or your router was just blocking it all together...

This sucks. It eventually keeps doing the same thing again and again. When I leave my house and try to reconnect later when I get home, WHAM! No connections. It can find my router and says it's available but when it tries to connect, it can't. I don't know what the hell is wrong.
I've master resetted both my phone and router and started all over from scratch.

On my Linksys router i use no security protocols. i use MAC address filtering instead. If the router does not have your mac address you can not connect. Drives the neighborhood war-drivers crazy!! It says unsecured, but they can not connect no matter what they try!

me neither
Since I installed wm6, my wifi will connect to my network but apps like internet explorer won't load a page , it just stays stuck on : "locating...."
any idea?

guesserit said:
Since I installed wm6, my wifi will connect to my network but apps like internet explorer won't load a page , it just stays stuck on : "locating...."
any idea?
Click to expand...
Click to collapse
Me 2, same thing.

Go to the settings for wifi and go to "Configure Network adapters" and make sure the all say the "The internet" and not "work"

sprice82 said:
Go to the settings for wifi and go to "Configure Network adapters" and make sure the all say the "The internet" and not "work"
Click to expand...
Click to collapse
That's the first thing i did buddy.

I am not really sure what it could be then, when I intaslled the official cingular wm6 Rom it was doing the same thing then I did a hard reset and when it was installing the extended Rom I did a soft reset and that fixed it, but then again I hyad to manually put all the settings in.

You might want to check if your really connected... If I start mine out about 1 inch from the router and get connected, I can walk all over the house and it will show connected (even updates the signal strength). However...IE will just keep saying 'locating' like yours. This is because it cannot reach the wifi base with it's buggered up transmitter. I don't think there is a cure for this.... Ikeep looking though...

badbert said:
On my Linksys router i use no security protocols. i use MAC address filtering instead. If the router does not have your mac address you can not connect. Drives the neighborhood war-drivers crazy!! It says unsecured, but they can not connect no matter what they try!
Click to expand...
Click to collapse
How do you do that and find the mac address on the 8525? I'm using Black Majik's cooked rom so it may be different from the original WM5.
Also an update on hooking to my router. I disconnected my router and cable modem and left it off for about 3 minutes. I then plugged it back in and let both reset. I connected afterwards and it works fine. Don't know what will happen later on when I leave and it disconnects.

How I solved Wifi problem

Lately I have been reading many post related to Wifi problems in the HD. I had the same. Even I was very near my router I couldn't connect to the net and the signal was very weak.
So I entered my router configuration and I found a solution.
Before, for security options I had: WPA-PSK [TKIP] then I changed to WPA2-PSK [AES] (of course you also have to change your HD connection configuratoin), and now it works great¡¡¡¡
Now I have all the bars for the signal and I can connect very easily.
Hope it works for other people

I have a similar WiFi connectivity problem, but after reading of the poor service provided by most vendors and HTC itself, I will try to gather some more experience with the problem before I contact HTC or my vendor, and hopefully find a solution. Bellow is my experience so far:
I own an HTC Touch HD since January and have a similar problem, only it surfaced last week. Before I had only used the WiFi connectivity briefly. The problems started after I installed an AP on my house expressively for the new PDA. The node is fully open and set to B/G/N protocols.
After a couple days of medium (couple hours per day) use the WiFi connection suddenly quit, the device would try to connect (the top bar showing the WiFi connection animation continuously) and after a few moments gave up with a dialog box stating the current network settings were wrong (even thou they worked fine a few hours earlier).
I tried several hot and cold resets, but only solved the problem after flashing a new ROM; even then the same symptoms reappeared after a couple of days of regular use. Again no re-setting would cure the problem, and now not even flashing the ROM again would work. Nonetheless, some hours latter the WiFi would connect perfectly with the same nodes it refused to before, and in very short time.
I have witnessed this cycle twice and have yet not been able to find a trigger for it, but will keep my eyes open for any tell tale signs, and post any findings here.

I could add to the above mentioned problems.
i got a new hd just few days back.
The wifi worked great. But now it doesnt.
I have disabled wifi, so can start it whenever i require.
I click on wifi button to enable it.
Then open opera, try any website.
it will open fine.
For instance say my email at gmail.com
Now after that if i try to open anysites or even continue with my mail, it shows error saying connection not available.
One of the workaround is to go back to toggele wifi off and switched it on.
Not sure if anyone faces a similar issue.

I's been about a week since my last post and I have already witnessed a couple of cycles of WiFi connecting perfectly and then not connecting at all.
No matter the settings I try after it decides not to connect, it won't. Even to nodes it had connected perfectly and fast jus minutes before.
I thought re-flashing might help but so far has proven ineffective. Once I thought some part of the non-volitile memory was causing the problem since after I cleared the memory I could connect for a while.
Any thoughts anyone?

Same problems here.
For the last hour I have been reading 10ths of threads here concerning WiFi problems.
My HD's WiFi worked fine on my home and outside for about 2 months. Now it doesn't. It reports connection, but no program can use the internet. At best, it seems to be able to exchange some Kbytes the for just a few seconds after a connection is established. Then nothing. Connected but unusable.
Tried everything Internet/My Work/My ISP, WAP enabled/disabled, soft/hard reset, everything.
When connected through ActiveSync everything works fine, all programs see internet.
Has anybody taken their HD to the service? Has any HTC service worldwide identified the problem as hardware and solved it by replacing something?

miskasp said:
Lately I have been reading many post related to Wifi problems in the HD. I had the same. Even I was very near my router I couldn't connect to the net and the signal was very weak.
So I entered my router configuration and I found a solution.
Before, for security options I had: WPA-PSK [TKIP] then I changed to WPA2-PSK [AES] (of course you also have to change your HD connection configuratoin), and now it works great¡¡¡¡
Now I have all the bars for the signal and I can connect very easily.
Hope it works for other people
Click to expand...
Click to collapse
I have just encountered a similar problem, but already used wpa/wpa2 with aes. Have tried a hard reset with no joy. My old HTC Touch has no probs connecting via wifi nor does my laptop so I would surmise that the prob is with the HD and not the router.
I am going to try flashing with the latest version of Duttys 6.1 rom and see what gives.
Edit: Tried flashing with new rom with no success. Take a look at this post.
http://forum.xda-developers.com/showpost.php?p=3769339&postcount=7
There are a couple of files to download but i only used the second ie this one.
http://forum.xda-developers.com/showpost.php?p=1363759&postcount=2
Now no problems and can connect via wifi no probs, ip address assigned by dhcp.

Try to go into WiFi settings and move the power slider to max performance. I need to do it here to access my router. This happened also with my HTC TyTN II, with any recent radio firmware. The original WM 6.0 ROM and it's radio work fine in low power mode, but the new ones appear connected but are always at 1 Mbps and there's no traffic until you move the slider to performance mode.

You go into WiFi settings and you configure manual IP and DNS so as router.
DNS is important.
Whit manual configuration, Wifi work always.
(sorry for my english)

Dubh Llas said:
There are a couple of files to download but i only used the second ie this one.
http://forum.xda-developers.com/showpost.php?p=1363759&postcount=2
Now no problems and can connect via wifi no probs, ip address assigned by dhcp.
Click to expand...
Click to collapse
Yeah, but what if I 'm not Orange-UK (let alone UK) ?
vcespon said:
Try to go into WiFi settings and move the power slider to max performance.
Click to expand...
Click to collapse
1st thing I did. Problem still there.
campotino said:
You go into WiFi settings and you configure manual IP and DNS so as router.
DNS is important.
Whit manual configuration, Wifi work always.
Click to expand...
Click to collapse
This is not a solution. I didn 't buy the device to be able to connect to my home WiFi only. What about public hotspots? Or hotels? Or whatever outside your home?

[HELP] WiFi isn't working / turning on!!

Xda-viewers,
yesterday i tried to put on my WiFi, but it didn't work anymore
I have my HD2 for about 1month, very happy with the phone,
and this is the first mayor malfunction
When i press WiFi ON in the comm-manager it shows it's loading,
and then nothing, doesn't go ON,
turned the phone off-on, soft reset.. nothing..
anyone else had this glitch?
hard reset or other solution?

It always worked, untill yesterday

If I were you I would go for a full backup with SPB, and then restore (maybe excluding everything regarding the wifi) after a hard reset

I would try doing hard reset.
However, I had the same problem with my old Fujitsu Siemens Pocket Loox N560 and they had to exchange mainboard.

Do you have it charging? I can't seem to connect to any Wifi networks when I have the phone plugged in. Once i disconnect it, it works fine.

If you are connecting it using USB, make sure WMDC / ActiveSync is set to allowing your phone wireless connections while connected to your PC!

???
phone is fully charged
not connected to PC or anything
not working, going to try some things
anyone goto suggestions except hard reset?
else i hard reset tommorow,
thankz

You mean you can't turn ON or NOT CONNECTING?
If its not connecting, did you try to delete the connection settings from advanced wireless settings and try reconnecting again?

skr_xd said:
You mean you can't turn ON or NOT CONNECTING?
If its not connecting, did you try to delete the connection settings from advanced wireless settings and try reconnecting again?
Click to expand...
Click to collapse
It's really not turning ON.
I press the Off-On button, I see it loading and then, nothing,
WiFi is still turned OFF.

timodc said:
It's really not turning ON.
I press the Off-On button, I see it loading and then, nothing,
WiFi is still turned OFF.
Click to expand...
Click to collapse
I've got exactly the same problem - have only noticed it today.
If I go into wireless network config and select my network there and click connect, it takes ages before it says "connected" and then immediately changes to "not connected". I've obviously checked and rechecked my settings. It simply will not connect any more.

i also can't remember installing an update which would cause this probleme..

Connected to PC
When connected to PC, in the comm manager, the WLAN is dissabled, can't even push it, maybe something went wrong with disconnecting and this is the reason why my WiFi is not working - going on?
Anyone?

I'm not at home, so can't do anything with mine at the moment, but out of curiosity, did you use then Wifi N option in BsB Tweaks? That's the only thing Wifi related that I can think of touching recently.

Tried it
Indeed, thought the same,
tried to put Wifi-N off, soft-reset, but no change
Almost at the edge of HARD-reset

timodc said:
Indeed, thought the same,
tried to put Wifi-N off, soft-reset, but no change
Almost at the edge of HARD-reset
Click to expand...
Click to collapse
I really hope it doesn't need a hard reset. I'm not gonna be happy if I have to do that AGAIN!
I'm gonna keep searching, in the hope of finding a solution.
Out of curiosity, do you ever use the Wifi router app?

WM-Wifirouter
I tried to use the Wlan-Router with Comm manager,
didn't work that well,
installed app I had on my P3600: WM-Wifirouter,
this worked like a charm,
Timo

I've solved my problem! Yay!!
I don't know if this will be of any help to you, but give it a try and see how you get on.
Basically, when using the in-built wifi router, it assigned the IP address 192.168.1.1 to the wireless adapter. This is fair enough, for a router, but obviously not for when you want to connect to a wifi network and get assigned an IP address automatically.
I had seen other people suggest that this may be the problem, so I'd already checked my IP settings for the wireless adapter, and they were set to automatic.
However, if you run the wifi router and then go to your IP settings, it says 192.168.1.1. Set it to automatic while the router is running.
This made my phone get a bit upset, and I ended up reseting it, but since then I've been able to connect to my home network again.
So...
1. Run and start the wifi router
2. Go to settings, Connections, Wifi, Wireless networks, Network Adapters (tab)
3. Select the network adapter (Broadcom 802.11 DHD Network Adapter)
4. Change to use a server-assigned IP address, instead of a specific one
5. Click OK
6. Reset the phone - don't close the wifi router app first.
7. When it starts up, go to the comm mananger and disable wifi.
You should now be able to start wifi and connect to your home network. (It may do it automatically if you don't do step 7 - I'm not sure).
Give it a try and let us know how you get on

Sensational johncmolyneux!!!
I had this problem too - it was doing my head in, but now seems like an obvious conflict. Thanks for finding the solution.
Now all I need to do is solve my BT Voice Commander problem (reported in many other threads) and the HD2 will have the same functionality as the Hermes it has replaced ;-)
Cheers,
Lordbowl

You still haven't hard reset?! I am doing hard reset every 6days because of mod/theme and other crap testing
Backups with resco/pim/office2007 entreprise on windows 7 beta do the trick to have phone working in 15 minuts.

johncmolyneux said:
I've solved my problem! Yay!!
I don't know if this will be of any help to you, but give it a try and see how you get on.
Basically, when using the in-built wifi router, it assigned the IP address 192.168.1.1 to the wireless adapter. This is fair enough, for a router, but obviously not for when you want to connect to a wifi network and get assigned an IP address automatically.
I had seen other people suggest that this may be the problem, so I'd already checked my IP settings for the wireless adapter, and they were set to automatic.
However, if you run the wifi router and then go to your IP settings, it says 192.168.1.1. Set it to automatic while the router is running.
This made my phone get a bit upset, and I ended up reseting it, but since then I've been able to connect to my home network again.
So...
1. Run and start the wifi router
2. Go to settings, Connections, Wifi, Wireless networks, Network Adapters (tab)
3. Select the network adapter (Broadcom 802.11 DHD Network Adapter)
4. Change to use a server-assigned IP address, instead of a specific one
5. Click OK
6. Reset the phone - don't close the wifi router app first.
7. When it starts up, go to the comm mananger and disable wifi.
You should now be able to start wifi and connect to your home network. (It may do it automatically if you don't do step 7 - I'm not sure).
Give it a try and let us know how you get on
Click to expand...
Click to collapse
-When I try to connect the WLAN-Router with the Comm Manager, it keeps on loading and nothing happens.
-When I try the WM-Wifi-Router app which I used on my P3600, it says not abble to connect WLAN
-All my settings are server-assigned-IP-address
Still not able to put on my WLAN,
Timo