Related
hello i have an hd2 tmobile branded i cannot seem to hspl it because on 1024 i get usb conectiong failed but it does go on tri color screen and in hspl2 i get bad model id.
this is what i have on my tricolor:
PB81120 SS-B3
SPL-20.8.0000 8G XE
MICROP LED 0X05
MICROP TOUCH 0X40
PLEASE HELP =/
THANKS IN ADVANCE.
this is what you need my friend..
then you will be able to download the tmobile energy rom
http://rapidshare.com/files/368532303/HSPL2_1024_RUN.zip
HI,
I used the HSPL2_1024, selected the 2.0.0.8
After 10 min, of using Energy.Leo.23549.Sense2.5_TMobile_USA.Mar.26
I got an error, I recovered, but wondering what happened??
Just try it again. Make sure your drivers are all complete from Windows Vista or 7. Make sure you are running 6.1 Windows Mobile Device Center.
I am sure you have done this but make sure:
Plug in your phone make sure the drivers are good with Active Sync on.
When you get into HSPL2_1024 and let it run your device will be found again in USB mode. Just to make sure the drivers are loaded correctly.
Flash - reboot and then flash the Energy or whatever USTMO compatible cooked ROM you like. I think there are only 2/3 that work with the ROM 2.08
Sometimes it just takes retracing your steps to get it to work right.
good luck.
I didn't want to make a new thread for this and clutter up the board, I'm kind of a noob to XDA you see. I just bought a Tmobile HD2 and downloaded and applied the HSPL linked in this thread, it all worked fine. My problem is: Will installing the 2.09.51.03 radio on my tmous HD2 hurt it? Was the 2.09 radio meant for the htc hd2 which has a different radio?
My main goal is to get Artemis rom on it.
Thanks for your time.
Lazarpandar said:
I didn't want to make a new thread for this and clutter up the board, I'm kind of a noob to XDA you see. I just bought a Tmobile HD2 and downloaded and applied the HSPL linked in this thread, it all worked fine. My problem is: Will installing the 2.09.51.03 radio on my tmous HD2 hurt it? Was the 2.09 radio meant for the htc hd2 which has a different radio?
My main goal is to get Artemis rom on it.
Thanks for your time.
Click to expand...
Click to collapse
The .51 radios are meant for the European spec and will not work on a TMOUS based rom AFAIK.
yeah i have installed mobile center twice straight from microsoft, my phone is synced with it, i run the 1024 it says connecting 5 min later says usb connection failed my phone does go into the tri color screen with the USB at the bottom =/ please really help
S3BAZ10 said:
yeah i have installed mobile center twice straight from microsoft, my phone is synced with it, i run the 1024 it says connecting 5 min later says usb connection failed my phone does go into the tri color screen with the USB at the bottom =/ please really help
Click to expand...
Click to collapse
try different usb ports and remember to right click 1024 and 'run as administrator'
After using the HardSPL I could not get my phone to sync either... So Just put your phone into bootloader mode. Turn off phone, power button, volume down hold till tri color screen comes up. Then just run the RUU an it will flash your phone. Only NRGZ rom works.
richsark said:
HI,
I used the HSPL2_1024, selected the 2.0.0.8
After 10 min, of using Energy.Leo.23549.Sense2.5_TMobile_USA.Mar.26
I got an error, I recovered, but wondering what happened??
Click to expand...
Click to collapse
You have to choose. 2.0.0.8 HSPL
msmith1991 said:
this is what you need my friend..
then you will be able to download the tmobile energy rom
http://rapidshare.com/files/368532303/HSPL2_1024_RUN.zip
Click to expand...
Click to collapse
Would anyone happen to have a mirror to this link, or could some kind soul possibly upload it? This one seems to be broken. It would be greatly appreciated.
Update...I found it.
yeah notinh still not working ive tryed all ports, im running windows 7 64bit.
I'm recieving the same error. Windows 7 x64, MDC is latest 6.1. Tried from both laptop (Win7 x64) and desktop (Win7 x64). Phone goes into Tri color screen, says "USB" at the bottom. Windows notes new driver, updates, then HSPL2 for 1024 Leo gives "Critical Error" and bombs out. Bummer
UPDATE: Fixed it. Did a hard reset on the phone, tried again, and now HSPL flashed successfully. Now, on to the cooked ROMs
Worked for me on win 7 x64... No issue with HSPL2_1024_RUN file I got by browsing this site... It did freeze on me during RUU, but I just rebooted and ran it as admin whilst not touching any other program in windows until it was done and it worked.
zoth said:
You have to choose. 2.0.0.8 HSPL
Click to expand...
Click to collapse
I believe you are to choose 2.08 to install HSPL
And you choose 2.08.0000 when you want to uninstall HSPL, for warranty and such.
well i had done a hardreset before but nothing, i tryed it on my laptop and it worked fine, guess it was my PC =/, thanks anyways to all you who tryed to help.
S3BAZ10 said:
well i had done a hardreset before but nothing, i tryed it on my laptop and it worked fine, guess it was my PC =/, thanks anyways to all you who tryed to help.
Click to expand...
Click to collapse
Please change the Thread title by adding {Solved} or something like that to note that your issue has been resolved.
hi guys, I tried all of hspl2 (1024) version for TMO US htc HD2 but it does not work at all. Pls help me.
Critical error is showed up by hspl2
My Phone softare information;
OS 5.2.xxxx
Manila 2.5.xxxxx
Rom v 2.10.xxxx(82076) WWE
Radio 2.08.xxxxx
I still use stock rom which is TMO US's shipping rom
I checked whole Hspl2 (1024) but doent work, Pls help me,
Moved you over to General. HSPL questions should have been posted in the hspl thread already open buddy.
Peace,
Josh
ok. I'll do it. thank you
hey guys trying to flash my first WM(US T-MO HD2) phone but its not working out.i followed every procedure given by MSKIP but i keep getting this message after pressing next on HSPL2_RUN: "CRITICAL ERROR,FLOW:00000003,ERROR CODE:00000004,DESCRIPTION:BAD MODEL ID".i turned off antivirus and restarted my windows 7 then connected my device with WINDOWS MOBILE DEVICE CENTER v.6.1 and then executed the HSPL2_RUN but didnt work out.bootloader screen shows up at the bottom saying usb and the phone didnt brick it just stayed in bootloader till i took the battary out and restarted the phone.what am i doing wrong please correct me.thank u
pretty sure thats the wrong hspl2.
Use teh link in my sig to get hspl1024 and compare it to the one you have,
I agree sounds like the wrong hspl. When you actually flash it the hspl should be 2.08.0000 not 2.0.0000 as the unlocker provides 2 options.
lwrdrchvy2 said:
I agree sounds like the wrong hspl. When you actually flash it the hspl should be 2.08.0000 not 2.0.0000 as the unlocker provides 2 options.
Click to expand...
Click to collapse
or did you mean to say "When you actually flash it the hspl should be 2.08.hspl not 2.08.0000 as the unlocker provides 2 options."
I was referring to the actual ruu, when the window displays on your pc it needs to be the 2.08.000 hspl, once the phone is unlocked the spl line will read 2.08.hspl like you stated.
thanx guys i will try SAMSAMUAL's HSPL2_1024_RUN and c if it goes through.thanx
thank u SAMSAMUEL that was the right HSPL.thanks to u and other i've finally succcessfully flashed my first WM phone.
all credit goes to Bepe, Cotulla and the DFT whos genius gave us HSPL
hspl1024
@samsamuel -
im very new to this and am pressuming i need hspl1024 for my t-mobile htc hd2. i tried looking in your signature but couldnt find it. is it hspl3 that u mean?
trying to get hspl so that i can switch the os to andorid.
it would be great if you could help and email me at [email protected]
thanks again
zorawar said:
@samsamuel -
im very new to this and am pressuming i need hspl1024 for my t-mobile htc hd2. i tried looking in your signature but couldnt find it. is it hspl3 that u mean?
trying to get hspl so that i can switch the os to andorid.
it would be great if you could help and email me at [email protected]
thanks again
Click to expand...
Click to collapse
hspl3 is just an updated hspl1024, updated to support more model id's. You can use either. hspl1024 is on page 99 of the HSPL thread, however yes, you can use hspl3 in my sig. choose 2.08.hspl not 2.08.0000(0000 is stock)
When you say so you can switch to android, you dont mean the youtube vid and connected site with the 'android beta OS installer' do you? which says you need hspl 1.42.hspl? cos thats a fake.
Please People...I really need help here..My phone make me crazy...
I try to flash my EU HTC HD2 with Android Nand rom and i have problem with that so i decide to put everithing on default with stock rom...
I download it and try but all the time error 290, and i read and read and somebody said that i need to have 1.42.HSPL (in that moment mine was 2.08. HSPL) ...so i do that with the HSPL2_Run and all procedure to back my hd2 to STOCK was faild again...
So i decide to turn beck HSPL to 2.08.HSPL and install some CustomRUU but from that point i have the same
CRITICAL ERROR
FLOW:00000003
ERROR CODE:00000004
DESCRIPTION:BAD MODEL ID....
I use HSPL2_RUN and HSPL4...and it was working...but now just error...What happend? What can i do?
How that can work in one moment and in another not... :-/
Forward Thankful...
In bootloader, what does the top line of text say?
same problem as Camsy..
in top right of bootloader i've RUUNBH, and after this there's 8g8g8g8 SS-BC.
Now i've loaded hspl.3.03 but i want to downgrade at hspl2 cause hspl3 is not compatible with my hd2.
OK, please try to help me.
I'm having trouble in changing the SPL in my Leo.
I have installed WRONGLY SPL 2.08 instead of HSPL 2.08 by DFT HSPL3
Since this made me unable to install MAGLDR, i tried idiotic idea to install the newest stocking ROM from htc site (Serial confirmed) with htc installer from windows.
Right now, i have working HTC with details as below:
ROM: 3.14.479.2 (04666) WWE
RADIO: 2.15.50.14
SN: HT03DNW00564
When i get into bootloader, there is:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
So, time for the problem:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens. DFT HSPL just shows progres bar moving and nothing happens (i have waited 20 mins).
I have no more ideas anymore, what can i do. Hopefully Phone works, and those not have any Cooked ROM on it, but i don't wont to use this ROM
PLEASE, try to help...
PS. I have tried different USB Ports, i have installed fresh Windows (really). I'm using XP SP3. Battery is at 100%.
Try running a task 29 and then run the HSPL again and install the 2.08 HSPL. Then flash MAGLDR then the ROM you want.
Edit: Sorry I momentarly forgot you have to have HSPL to do a task 29. Do this make sure your phone is in bootloader and plug it into the computer via USB cable and then wait until it says USB at yhe bottom in the white. Then and only then run the DFT HSPL again.
With Task29 also nothing happens. Same as with ROMS and HSPL, After synchro in ActiveSync, i have run TASK29, then my Leo goes into Bootloader and nothing happend. On Windows screen i have 0% progress bar, on HTC HD2 i see bootloader with USB status.
ERROR 302
EDIT: After clicking through recovery steps, Leo turned to showing Progres bar, but also stops at 0%.
RealWaaagh said:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.479.1
Click to expand...
Click to collapse
Just making sure: did you try to flash those stock roms over USB? Stock SPL's don't have the same protection that HSPL has, and can be overwritten by flashing over USB just fine.
Also: until you're sure you can reflash at least something, it might be better to stay away from task29
I tried also by USB (all three), and still the same. Progress bar on PC and Phone shows 0% and after some time, Installer shows ERROR about connection. ERROR302 i think.
PS. I really start to think i'm missing some detail. ROM works, everything works excluding boot loader. For me, it looks like bootloader is broken somehow, and i don't have idea how to make it work properly.
RealWaaagh said:
I tried also by USB (all three), and still the same. Progress bar on PC and Phone shows 0% and after some time, Installer shows ERROR about connection. ERROR302 i think.
PS. I really start to think i'm missing some detail. ROM works, everything works excluding boot loader. For me, it looks like bootloader is broken somehow, and i don't have idea how to make it work properly.
Click to expand...
Click to collapse
Hmm... If you can't get your phone to flash anything over either USB or SD, it does sound like your bootloader might be corrupted or something. That 302 error also doesn't sound good.
I guess if you have them you could try flashing using:
- a different pc/laptop
- a different SD card (perhaps a goldcard?)
*Probably* won't help, but won't make things worse either.
Ok, for today i have enough. I will try tomorrow with another PC.
SD Cards i already tried three of them.
RealWaaagh said:
OK, please try to help me.
I'm having trouble in changing the SPL in my Leo.
I have installed WRONGLY SPL 2.08 instead of HSPL 2.08 by DFT HSPL3
Since this made me unable to install MAGLDR, i tried idiotic idea to install the newest stocking ROM from htc site (Serial confirmed) with htc installer from windows.
Right now, i have working HTC with details as below:
ROM: 3.14.479.2 (04666) WWE
RADIO: 2.15.50.14
SN: HT03DNW00564
When i get into bootloader, there is:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
So, time for the problem:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens. DFT HSPL just shows progres bar moving and nothing happens (i have waited 20 mins).
I have no more ideas anymore, what can i do. Hopefully Phone works, and those not have any Cooked ROM on it, but i don't wont to use this ROM
PLEASE, try to help...
PS. I have tried different USB Ports, i have installed fresh Windows (really). I'm using XP SP3. Battery is at 100%.
Click to expand...
Click to collapse
Mate, you said that you flashed stock rom v.3.14.xxx but you also said that the SPL 2.08.
I m quite confused, usually the stock rom v.3.14 contains SPL 3.03 (not 2.08). So, I m curious what version of your hd2, is it TMOUS?
Have you tried a HARD RESET?
Try HR and see whether your hd2 can pass that.
If succeded, you can retry flashing HSPL over usb (dont forget to turn off antivirus, firewall, internet on your pc) or else retry flashing via micro sd flashing (use 2,4 or 8 gb reformated micro sd)
hope you can succeed.
good luck
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens.
Click to expand...
Click to collapse
forget starting with the phone already running, it doesnt need to connect to activesync, that just adds a load of confusion, saying that in all the instructuons.
phone off
phone into bootloader
usb
hspl4
choose 2.08.hspl
bootloader
flash rom
I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
Click to expand...
Click to collapse
so thats two east europe and a wwe rom, , you dont have hspl installed, , and you're unsure why nothing will flash?
cancel this post
RealWaaagh said:
Ok, for today i have enough. I will try tomorrow with another PC.
SD Cards i already tried three of them.
Click to expand...
Click to collapse
One more question are you right clicking and running HSPL as administrator???
samsamuel said:
forget starting with the phone already running, it doesnt need to connect to activesync, that just adds a load of confusion, saying that in all the instructuons.
phone off
phone into bootloader
usb
hspl4
choose 2.08.hspl
bootloader
flash rom
so thats two east europe and a wwe rom, , you dont have hspl installed, , and you're unsure why nothing will flash?
Click to expand...
Click to collapse
I have already tried to start hspl4 without running WinMo, same effect. In WinXP Bootloader still displays on the Phone, and in DFT HSPL progres bar just bounce from left to right.
In Vista DFT HSPL returns critical error about connection.
About ROMS, 3.14 is East Europe (downloaded from HTC after checking serial) and 1.48 is WWE, also checked with serial from HTC site.
I have tried 1.48 EE since somewhere i have read, taht i have to get rom with the same number on the end, as installed (ie. 3.14.479."2")
PS. I can't tconnect to Mobile Center is Vista. With ActiveSync on WinXP there are no problems.
silverwind said:
Mate, you said that you flashed stock rom v.3.14.xxx but you also said that the SPL 2.08.
I m quite confused, usually the stock rom v.3.14 contains SPL 3.03 (not 2.08). So, I m curious what version of your hd2, is it TMOUS?
Have you tried a HARD RESET?
Try HR and see whether your hd2 can pass that.
If succeded, you can retry flashing HSPL over usb (dont forget to turn off antivirus, firewall, internet on your pc) or else retry flashing via micro sd flashing (use 2,4 or 8 gb reformated micro sd)
hope you can succeed.
good luck
Click to expand...
Click to collapse
My Phone is East Europe WWE (afaik).
I have installed SPL 2.08 onto HSPL 1.6 with DFT HSPL3.
Then i have installed 3.14 by USB. I don't know, why i still have SPL2.08 if you say i should't.
HR works fine.
In a minute i will check HSPL with internet turned off.
How to flash HSPL via microSD ?
Since i can't flash whole ROMs (maybe i have wrong ones, but they pass serial check on htc.com) from microSD (3 cards checked 2GB SD, 4 GB SDHC(don't work), 16 GB SDHC)
T-Macgnolia said:
One more question are you right clicking and running HSPL as administrator???
Click to expand...
Click to collapse
When i try run in Vista, i click and run it as Admin, but in XP i have Admin Account, so i just run it.
PS. Sorry for three posts, i didn't see multiple-quote option
RealWaaagh said:
When i try run in Vista, i click and run it as Admin, but in XP i have Admin Account, so i just run it.
PS. Sorry for three posts, i didn't see multiple-quote option
Click to expand...
Click to collapse
Doesn't matter, still right click and run as admin, always put phone in bootloader yourself before starting to flash, if it fails just run hspl.exe again. Try all USB ports.
No, you can't apply hspl from SD card.
samsamuel said:
Doesn't matter, still right click and run as admin, always put phone in bootloader yourself before starting to flash, if it fails just run hspl.exe again. Try all USB ports.
No, you can't apply hspl from SD card.
Click to expand...
Click to collapse
PROBLEM SOLVED
I needed to make another admin account in WinXP. And then use it by Run As (then choose this new account).
I don't know why it works like that, but it worked.
Just to give all informations.
After more testing, i detected my Computer problem. My USB ports were not working properly, and update of Motherboard BIOS helped (ASUS P7P55D). So, i don't know what was the exact issue of problems.
Hi there,
I've bought my HTC Leo 1 week ago and I want to install Android on it. I'm following the steps of this post but it's a little hard if you haven't flash a cell phone ever
The thing is that my cell phone has SPL 3.03.0000, but I need HSPL 1,2 or 3, So I need to downgrade the SPL to use the right HSPL.
Does anyone know how to downgrade the SPL? If I understood right I need to flash a new ROM of win mo 6.5 in my cell phone with the right spl, but I don't know where to find it.
Thanks!
Search for HSPL2 or HSPL3.
You actually need HSPL4 AFAIK. Just search for HSPL4 then download etc. Then go in to bootloader and run the .exe found in the file you've downloaded. Click through the steps and you'll get to a screen with a drop down menu, choose 2.08.HSPL from the menu. Then just click next and it'll flash.
Sent from my HTC Vision using XDA App
Skellyyy said:
You actually need HSPL4 AFAIK. Just search for HSPL4 then download etc. Then go in to bootloader and run the .exe found in the file you've downloaded. Click through the steps and you'll get to a screen with a drop down menu, choose 2.08.HSPL from the menu. Then just click next and it'll flash.
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
then I need HSPL4. I just saw this post and it says "Android / WP7 / MAGLDR don't support HSPL3.03/OSPL3.03. You need HSPL2.08 to run Android / WP7 / MAGLDR." So, among all the HSPL releases, the only one that doesn't work is the 3.03? If that's right the HSPL4 should work, I'll give it a try
Oh, I just see this post and it says "You must have hspl 2 or 3 for android to run well please use HSPL GUIDE" . Is there any problem with HSPL4 of the guide is old?
It won't matter. All HSPL4 does is flash 2.08.HSPL to bootloaders that have SPL 3 and up as the older versions are compatible with older SPL's (bootloader).
Sent from my HTC Vision using XDA App
Well, I have another problem now
I'm following this steps to put HSPL4:
2. Synch Phone with PC in Windows Mobile!!! It has to be connected to activesync or WMDC via USB cable
3. Run HSPL4.exe from your pc and read all the text carefully
4. When finished reading click next in the HardSPL program
I connect my phone to the PC, and the Windows Mobile center pops out, but when I go to the ActiveSync on my phone it says that I should install the ActiveSync software in my pc (I don't know why but I can't install ActiveSync on my pc, it says that my software is uncompatible (Windows 7, 64 bit), I read that WMDC is used in W7 instead of ActiveSync). So I executed the HSPL4 (phone conected) and wait 5 minutes, and it didn't find the USB conection of my phone with my pc :/
Anyone had this problem or know any alternative? :/
Thanks!
Done, I use the "NOTE: You can also install HARDSPL by entering Bootloader mode manually, then running the HSPL4.exe program once you see 'USB' at the bottom of the tri-colour screen.". I didn't saw it
Haha I was just about to say that. It's actually better if you run it straight from HSPL.
So are you all flashed now or what?
Skellyyy said:
Haha I was just about to say that. It's actually better if you run it straight from HSPL.
So are you all flashed now or what?
Click to expand...
Click to collapse
I just flashed it and now I have to install the Radio, but I have the same problem (in the steps it says that I need to be connected by activeSync)
I think I will try again from the Bootloader mode manually, what do you say?
Edit: In this post says that the radio have to be installed before the rom, but in this one it says the opposite.
(I'm a little lost )
Install everything from the bootloader. They;ll all flash correctly from there.
Install the radio before the ROM. Make sure you flash 2.15.50.14 then flash MAGLDR and flash away!
mm, I downloaded the radio 2.15.50.14 but when I execute the CustomRUU and the phone is conected in Bootloader mode it doesn't recognize the phone :S
I can't figure out any solution... what a thing...
PD: Now it shows SPL-3.03.HSP in the bootloader screen, so that's ok
Actually no that's the reason why its not okay. You flashed the wrong HSPL. Just go back to bootloader, open up HSPL4 and when you get to a drop down menu chose 2.08.HSPL from the menu. That's the one you need. Flash that, then reflash the radio and it will flash properly.
Sent from my HTC Vision using XDA App
i don't know
christian.patella said:
i don't know
Click to expand...
Click to collapse
Thank you for the useful post...
Sent from my HTC Vision using XDA App
Oh, I've just realized one thing.. In this post says:
★STEP 2★
Prepare your device
windows rom - windows rom has been linked with issues within the android builds so for the first time im going to compile a list of working roms here that have no issues within android
i have been using ChuckyROM GTX + CHT 1.8.5 - 23128 from the start of android development and have yet to have an issue below is a list of other roms and links that are working well with android :-
BARE BONES WM ROM FOR ANDROID BY NRGZ28
[ROM][WWE]★★★Astraios Roms★★★[REG/BUUF/GTX][23569][22nd July]
ELEGANCIA ROM Series™
ChuckyROM GTX + CHT 1.8.5 - 23128 ~ 2.10.1
¸¸.·´¯`·.¸¸.- Energy -.¸¸.·´¯ | 21911||23129 * Sense 2018
★★★ PLEASE LEAVE LINKS AND INFORM ME OF ANY ROMS YOU HAVE TRIED AND HAD NO ISSSUES ★★★
FOR INFORMATION ON HOW TO FLASH A ROM PLEASE GO TO FLASHING GUIDE.
That means I have to install another windows rom before the android one?
PD: When I installed the HSPL 3.03.0000 (by mistake) and then the 3.03.HSPL, in both cases it shows ''We hacked it!'', but I just install the 2.08.HSPL and it didn't show anything, it just said ''Succesfully done'', is that ok? . Edit: The phone displays the right version of SPL, i'll try with the custumRUU in a moment
I'm waiting for the answer I'm afraid of running the customruu without haven't changed the WM Rom (That step is't very clear for me )
If you have 2.08.HSPL on your phone all you need to do now is flash MAGLDR from the RUU. You don't need a custom WinMo ROM if you have the correct radio etc. as MAGLDR will over-write WinMo anyway.
So basically if your phone is saying 2.08.HSPL just go back to the bootloader and flash the MAGLDR RUU.
Help please
dami_rz said:
Help please
Click to expand...
Click to collapse
I have.
Okay, I've spent about a week trying to figure out why I can't get HSPL4 to flash 2.08.HSPL onto my phone (and subsequently MAGLDR 1.3, then SOME version of Android).
I'd like first to apologize to samsamuel if I missed a thread somewhere that addresses this issue - I know you've gotten frustrated with a lot of people asking the same questions over and over =/
So here's the problem... I have a WinXP machine running ActiveSync 4.5 that recognizes my phone. When I first got my T-Mo HTC HD2 a year and some change ago, I went ahead and used the SD card to run an old version of Android (executed from within WinMo 6.5). At some point it died, and I went on using WinMo 6.5.
I got fed up with it and decided to try and go the HSPL/MAGLDR route. However, when I sync up the phone (usb cable -> hd2 w/ActiveSync, Enable Data Sync unchecked) and run HSPL4, it finds the phone, reboots it into rainbow mode, tells me I have "SPL 2.08.0000 ||", allows me to select 2.08.HSPL, then hangs on the "Please wait while installing the HSPL. Do not touch the device!!" screen and just keeps scrolling the progress bar back and forth. I left this up overnight (~8hours) and neither the phone nor the progress screen changes. No errors, nothing.
I've currently got the stock 2.10.0 ROM on the device, but I've also tried the 3.14.0 stock ROM (SPL 2.10.000) to no avail.
Here's all of the info I can think of to provide...
T-Mobile HTC HD2, 16GB MicroSD, 576MB RAM
R: 2.08.50.08_2
G: 15.34.50.07U
D: 2.10.82076
Rainbow Road says:
PB81120 HX_B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Any help troubleshooting this would be greatly appreciated!
-Skye
SkyeDaemon said:
Okay, I've spent about a week trying to figure out why I can't get HSPL4 to flash 2.08.HSPL onto my phone (and subsequently MAGLDR 1.3, then SOME version of Android).
I'd like first to apologize to samsamuel
Click to expand...
Click to collapse
lol!
when I sync up the phone (usb cable -> hd2 w/ActiveSync,
Click to expand...
Click to collapse
Don't do that,, put phone into bootloader manually, and then run hspl,,, USB times out in the time taken to restart the phone into bootloader.
samsamuel said:
lol!
Don't do that,, put phone into bootloader manually, and then run hspl
Click to expand...
Click to collapse
Tried that as well, still the same result. =( It recognizes the installed SPL version "2.08.0000||", I select 2.08.HSPL, it goes to the "Please wait..." screen and then nothing happens. Progress bar animates indefinitely and phone just sits on rainbow screen (USB displayed at bottom).
I've tried with and without the MicroSD card and with/without the SIM card. Same result.
Any ideas?
SkyeDaemon said:
Tried that as well, still the same result. =( It recognizes the installed SPL version "2.08.0000||", I select 2.08.HSPL, it goes to the "Please wait..." screen and then nothing happens. Progress bar animates indefinitely and phone just sits on rainbow screen (USB displayed at bottom).
I've tried with and without the MicroSD card and with/without the SIM card. Same result.
Any ideas?
Click to expand...
Click to collapse
If you stay on the rainbow screen, please have a look if USB is indicated.
If so, unplug and plug again the cable. USB disappears and come again.
Try again..
SkyeDaemon said:
Tried that as well, still the same result. =( It recognizes the installed SPL version "2.08.0000||", I select 2.08.HSPL, it goes to the "Please wait..." screen and then nothing happens. Progress bar animates indefinitely and phone just sits on rainbow screen (USB displayed at bottom).
I've tried with and without the MicroSD card and with/without the SIM card. Same result.
Any ideas?
Click to expand...
Click to collapse
Taco123 said:
If you stay on the rainbow screen, please have a look if USB is indicated.
If so, unplug and plug again the cable. USB disappears and come again.
Try again..
Click to expand...
Click to collapse
yea fiddle with the cable to be sure its connected, but to be honest, rather than spend hours trying, find a 32bit machine to try it on, id lay 60:40 on it working straight away.
SkyeDaemon said:
I'd like first to apologize to samsamuel if I missed a thread somewhere that addresses this issue - I know you've gotten frustrated with a lot of people asking the same questions over and over =/
Click to expand...
Click to collapse
I genuinely laughed at that :')
Also, as far as I can remember there is no stock ROM called 2.10? And flashing stock ROM 3.14 should give you SPL 3.03 not 2.10
Nigeldg said:
I genuinely laughed at that :')
Also, as far as I can remember there is no stock ROM called 2.10? And flashing stock ROM 3.14 should give you SPL 3.03 not 2.10
Click to expand...
Click to collapse
(and to think ive been trying hard not to bite lately, , , hehe)
2.10 was the original t mo, with spl 2.08.0000, 2.13 has 2.10.0000, and the tmous seems not to require spl 3.03.0000 to run 3.14, while the regular runs bad and loses ram when it uses 3.14 with any other spl than 3.03.
If so, unplug and plug again the cable. USB disappears and come again.
Try again..
Click to expand...
Click to collapse
Tried that. Unplugging the USB cable switches the indication to "SERIAL" and plugging it back in switches to "USB" again. I've tried two cables as well. It's not losing connection =/
find a 32bit machine to try it on, id lay 60:40 on it working straight away.
Click to expand...
Click to collapse
This is on a 32-bit install of WinXP =/
Also, as far as I can remember there is no stock ROM called 2.10? And flashing stock ROM 3.14 should give you SPL 3.03 not 2.10
Click to expand...
Click to collapse
I think I've been running in circles long enough trying to figure this out that I've thoroughly confused myself on how to correlate the ROM version and the SPL version, lol.
I guess I'll try another machine when I get home from travel, but so far still the same weird issue where it just sits there. Any other suggestions are welcome!
SkyeDaemon said:
This is on a 32-bit install of WinXP =/
!
Click to expand...
Click to collapse
heh my mistake, was thinking of another thread.
Thought of trying hspl3? hspl4 is only necessary if you are on 3.03.0000
There are even some threads talking about hspl4 possibly causing problems, even going as far as causing the 'unable to get into bootloader' and 'bad modelID' problems,, but i haven't really looked into that so couldn't say.
samsamuel said:
(and to think ive been trying hard not to bite lately, , , hehe)
2.10 was the original t mo, with spl 2.08.0000, 2.13 has 2.10.0000, and the tmous seems not to require spl 3.03.0000 to run 3.14, while the regular runs bad and loses ram when it uses 3.14 with any other spl than 3.03.
Click to expand...
Click to collapse
Of course, completely forgot that TMOUS had different stock ROMs, my bad. As samsamuel said, HSPL4 has caused some problems for some people (not for me as far as I know, but it has for others), so try using HSPL3 which I would think is perfectly fine for your ROM version and SPL version currently.
No luck on HSPL3 either - exact same problem. Just sits there and does nothing, no errors or anything.
Tomorrow I'll try on my Win7 laptop to see if it's some sort of strange driver issue =/
Went ahead and installed all the necessary drivers on my Win7 machine, synced up and HSPL3 worked on it. I'm guessing there is a device driver issue or something on my WinXP machine that is preventing HSPL from working.
I may look into it further at a later date to try and post a (real) solution to the problem in case someone else runs into this, but for now the problem is resolved. Many thanks to those of you that replied to help =)