Is there a way to connect two phones together, either with bluetooth or wifi and have the camera from one display on the other?
i think you need to hard-reset your mobile phone...i mean first you shut down your device and then push down both the vol+up and vol+down button and press the power button until a 3-color screen shows up... then release both vol buttons and push vol+up button to reset, then your system will go back to the first time use condistions...
caution!!!! remember to backup before you do.!!!!
Don't do it.
xiamilo said:
i think you need to hard-reset your mobile phone...i mean first you shut down your device and then push down both the vol+up and vol+down button and press the power button until a 3-color screen shows up... then release both vol buttons and push vol+up button to reset, then your system will go back to the first time use condistions...
caution!!!! remember to backup before you do.!!!!
Click to expand...
Click to collapse
Umm, wrong post to reply to?
Do you mean something like Skype?
And for this to work via bluetooth the phones would have to be very close to each other since bit rate drops for bluetooth the further you get away.
I assume Skype needs net access. Was wondering if it exists (or is possible) for two phones to be connected directly in the same room/house.
Wanted to check something in one room while doing something in another and thought a remote display type thing using two WinMo phones could be handy.
Related
do you guys face this problem before?
first time, i don't know what happened, tried to press power button few times, the screen not ON. So i soft-reset.
second time, when i tried device locked and press Power button to standy during activesync to my notebook, after a while i press Power to ON it back but the screen show nothing. Then i tried called my pda with another mobile phone. My pda did not ring at all and i can heard the calling tone from another mobile phone. It seem like hang already.
Can anyone know what's my problem?
xSean said:
do you guys face this problem before?
first time, i don't know what happened, tried to press power button few times, the screen not ON. So i soft-reset.
second time, when i tried device locked and press Power button to standy, after a while i press Power to ON it back but the screen show nothing. Then i tried called my pda with another mobile phone. My pda did not ring at all and i can heard the calling tone from another mobile phone. It seem like hang already.
Can anyone know what's my problem?
Click to expand...
Click to collapse
Try a hard reset, see it if helps.
Hi people. having a bit of a crisis. my mini s wont startup any more? it just hands at the 'windows mobile' graphic?
anyone know any genuis solutions to help me get it working again?
pretty please *crying*
mark
Have you tried to give it some time? When i had old version of Polish official WM5 ROM from Era operator, my Wizard took more than 5 minutes to boot (instead of less than a minute with newer ROM). Also, sometimes it did hang in the process. What seemed to help (though i have no idea why) was not allowing the backlight to go off by tapping the screen once in a while during the boot process.
left it on, with charger plugged in to maintain juice all morning and its not gone any further
And how about keeping the device awake - tapping the screen during boot process?
it stays permanently awake from reset
What i meant, is that when my device booted, after a while the backlight went off. if i didn't tap the screen to turn it back on, the device simply hung. Then again, that was probably just a problem of my ROM/software combination, since i never saw anyone else describing such problem. If you have your data backed up, you might try a hard reset, if not, maybe someone else can give you a bit more useful advice
it just stays on. no tapping required.
is a hard reset the same as holding down the power button til it turns off because ive done that a few times now
any suggestions?
nope, hard reset is holding the comm manager and voice memo buttons pressed and pressing the side reset button. Keep these buttons down until you get a question if you want to restore your factory defaults (you'll have to press the call button if you do). Be arare that you'll lose all the data on your phone (those on the storage card will stay intact) - all the files, contacts, messages. I hope you have a backup of those...
strangely enough, held down those three buttons and instead of asking me to hard reset it vibrated and then popped the txt mesages screen up?
very bizare
must have been retaining the boot graphic on top of the apps?
thanks for the help!
mark
Well, i must admit - that sure is odd.
there is another way to hard reset - turn off your device completely (holding the power button for a few secs, and answer the popup message asking if you want to power down "yes" (from your earlier posts i understand that it worked). When the phone is completely off (no LED blinking), press the two side buttons i mentioned earlier (voice command and comm manager) and while holding them power the phone up just as you normally do - by power button. Keep both side buttons down until you get the question about resetting. If you hold the buttons and it gets to the windows mobile screen, then one of them might be faulty.
[EDIT]
I just thought o0f something else - if the SMS window pops up, it would mean that the device is actually booted, so it should connect with activesync. Maybe connecting it to the PC, opening the device's folder, and navigating to /windows/startup folder. Thye problem might be caused by one of the applications run on start, so try moving (not deleting) all items from startup to some location on your PC. Then do a soft reset (the reset button on the side). If it boots, post the list of apps you had in startup, maybe we can figure out which one was causing trouble and put all others back to startup. If not, then the problem is somewhere deeper in the system, and a hard reset will probably be necessary.
[/EDIT]
When i press the ON button to start the device ( after blank mode) . automatically the volume is invoked which is very annoying.
Is that becaouse of moisture...????
how to get rid of that?
What rom are you using? Maybe that rom has an alternative function for power button on long press.
i have WM 6.1 Rom. not yet upgraded.but it seems that when i press the power button , the last application gets invoked automatically. i dismantled the HTC completely and didnt see any moisture here.. i m not understanding whats the problem. if in stanby position (when light is off) , i revove the SD card , then also the last application ( camera or keypad, vol control, phone book) gets invoked.
The problem was noticed when in mp3 player " Power Music" gives a shattering sound once , in playing music the screen goes blank.
@hatcap_2000: Check for buttons settings in Settings->Personal->Buttons
If I am not entirely wrong (I could be ), you are not closing the 'last application'. Close that application, suspend the device and see if the problem persists.
Like if you suspend your device while volume control is displayed, waking the device back to on will display the volume control.
what application to close? if i access an vol key? dear.if i access camera key and then blank the screen, in next power on event..., i get camera activated. is it a hrdwr fault or software flt?
hatcap_2000 said:
what application to close? if i access an vol key? dear.if i access camera key and then blank the screen, in next power on event..., i get camera activated. is it a hrdwr fault or software flt?
Click to expand...
Click to collapse
If you click on the Speaker icon again, it will close the volume control.
Use task manager to close applications.
To me its a software fault.
Hush! to be on safer side i sold my cell for a good amt. @ 4500Rs. and bought N70 Nokia. Nokia rocks!!!!!
hatcap_2000 said:
Hush! to be on safer side i sold my cell for a good amt. @ 4500Rs. and bought N70 Nokia. Nokia rocks!!!!!
Click to expand...
Click to collapse
Thats a good one .
Its been long since I heard such a good joke
I bought a new phone (HTC TOUCH 2) from China.
It is same as the original one.
My problem is: I can't do a HARD RESET or Soft Reset by Button.
I searched the forums and found some talking about pressing (VOLUNEUP+VOLUMEDOWN+Power.
others talking about VOLUMEDOWN+Power
I tried every possible key compinations to do the HARD RESET with no success.
When i press VOLUNEUP+VOLUMEDOWN+Power, a green screen show up with the bellow data:
"THIS OPERATION WILL SET KITL MODE.
CURRENT SETTING........
DISABLE KITL: CAMERA
PASSIVE KITL:VOLUMEDOWN
ACTIVE KITL: VOLUMEUP
I searched for a Camera button but it seems this button is not there at all, only one tall button on the left side for Volume (up+down)
Also there is no Reset button at all, i searched every where in the mobile with no success even if i remove the styles, nothing there at all.
is there any help?
I have some problem with my htc clone i have no camera button but i must change kitl to disable to comunicate my htc with pc with active or passive kitl mode usb connection are not recognized by my pc. Is there any way to change kitl mode using wm mobile aplication or something like that i want to change my rom too. cause this one is probably for another htc with camera button
Hard Reset
Go to menu -> settings -> system -> clear storage to hard reset your phone
don't work with my problem after clear storage kitl stays in passive mode i need disable for usb comunication
Also, all owners of this mobile having the below problems:
1- Can't load normal Rom files (.nbh), they should load it through a flash memory
2- Rom File size should be smaller than 128mb.
3- Can't connect it with PC Post#2.
4- No Camera Button !!!!
Mine was disabled and I don't know which combination of buttons I pressed to enable it but now it really startups slow and also the usb connection problem came up. So anyone?
I tried each and every possible key combination with no success to Disable kitl.
Any help?
I would never trust a clone for a wm as i do keep all of my work on it. Never ever trust a chinese clone company for this. Better to pay a few dollars more and buy the real one than risk loosing all of my data kept.
You are right 100%.
but, what about the current case?
Do i have to put it in the trush bin?
Ravash said:
Mine was disabled and I don't know which combination of buttons I pressed to enable it but now it really startups slow and also the usb connection problem came up. So anyone?
Click to expand...
Click to collapse
Press (VolumeUP + VolumeDown + Power) then select Passive again...Working fine
Once press the "Windows logo" + "Volume Up" + "Power" working hard reset
Hard Reset is easy. Press the Volume up an down key from the center.i.e press it form the middle. like that both the up an down keys would be pressed. then Power on. Easy. yes it wasn't easy for me too in the start but a bit more pressure and it works.
Gothik said:
Hard Reset is easy. Press the Volume up an down key from the center.i.e press it form the middle. like that both the up an down keys would be pressed. then Power on. Easy. yes it wasn't easy for me too in the start but a bit more pressure and it works.
Click to expand...
Click to collapse
I have the same problem. Yesterday I put my cell phone passive KITL mode, but when I connect to my computer, nothing happens.
I did hard reset and soft reset but nothing happens.
Help me!
have you installed microsoft activesync (windows XP) or windows mobile device center (vista or 7)? i think you have to install those first.
robekia1 said:
Press (VolumeUP + VolumeDown + Power) then select Passive again...Working fine
Click to expand...
Click to collapse
How do you Select passive, when you get the screen of "this operation will set kitl mode. thank you
The screen will guide you.........
DID YOU REALLY PRESS THOSE BUTTONS?
Power button does not respond at any point.
*EDIT:except after battery out for a long time, then power button WILL turn the phone on, but then continues to not function as per usual.
However, the phone automatically turns on as soon as the battery is placed in, so it's not dead at least.
Also can not get the phone to be recognised on either of two computers (one running Win 7 and the other Vista) always get "device has malfunctioned etc"
Have re-flashed a ROM from SD but same problem. If holding down the Vol Down on start up (putting the battery in) I can get to bootloader, hence the re-flash. But holding down both gets to the hard reset 'warning' screen, but it won't let me press Vol Up to actually do the hard reset.
All in all a frustrating problem which means I have to remove my battery to turn my phone off and have to use the option from Windows Menu to lock the device.
Any help with any of the problems is greatly appreciated.
Also Power Button mechanical function is still normal.
Many thanks.
Sounds like your end key has become faulty as well as your volume up button. Both of witch are common issues, especially the end button, but most peoples volume down button wears out first. This is do to the fact that the end/power key is in constant use from turning on and off the HD2 or from getting MAGLDR to pulled up a bootup for those running NAND Android. Also the volume keys take a lot of wear and tear from constant volume adjustment especially if you listen to alot of music on your HD2. Plus the volume ..down key takes extra wear and tear from being used to enter bootloader.
hello
hello vsem
Yes it does seem that way, however I have had teh battery out over night, when I put it back in this morning it DID NOT automatically initiate the boot sequence. But it did after I pressed the power button, so it must have read it to some extent?
Also when the phone is on I can change the volume up and down as per usual, its all a bit strange.
Any other way to initiate a hard reset other than that menu?
Thanks very much!
It seems you are having a hardware issue, try sending your device to the service centre.